Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin Mist RAYBO PATTERN GLASS STYLES: Waterfall Bamboo Harp Mirage If you have a problem, question, or request, call your local dealer, or Steelcase Line at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call:.66.247.2500) Or visit our website: www.steelcase.com 2009 Steelcase Inc. Grand Rapids, MI 4950 U.S.A. Printed in U.S.A. NOTE: TRANSOM DOOR SHOWN CAUTION: Corner of the glass can easily be damaged while being installed. Please handle carefully! For etched/pattern glass orientation please refer to the installation drawings. Unless noted otherwise, use the default. DEFAULT GLASS ORIENTATION: ETCHED GLASS: Rough side to go on the inside of the office space. PATTERN GLASS: Rough side to go on the outside of the office space. SMALL SCREWDRIVER ENGLISH & METRIC ALLEN WRENCH T-HANDLE ALLEN WRENCH Page of 28
HANDLE ROLLER KIT BASE ROLLERS BASE CHANNELS HORIZONTAL ENTRY STOPS LIGHT SEALS TRACK KIT BOLT FULL HEIGHT ENTRY FRAME ASSEMBLIES (2 SETS) (2 SETS) HALF A (2 SETS) BASE RAIL ASSEMBIES SPLINE CHANNEL BASE SPACERS BASE COVERS WITH SCREWS VERTICAL ENTRY VERTICAL STRIKE HALF B (2 SETS) (2) PER KIT GLASS FULL HEIGHT SIDELITE TRANSOM HEIGHT SIDELITE TRANSOM HEIGHT ENTRY SPACERS COVER CAPS (2 SETS) SLIDER SIDELITE PLINTH WITH PLASTIC CLIPS SLIDER STRIKE PLINTH TRIM LEFT HAND RIGHT HAND Page 2 of 28
LOCK COVER (4) LOCK LOCK BODY CHANNEL LOCK PAD (2) - ONLY REQUIRED WHEN GLASS IS 3/8" THICK BLOCK CLAMP (2) TRIM RING - /4 THUMB TURN MORTISE CYLINDER #8-8 x FLAT HEAD TAPPING (2) #8-32 x /4 FLAT HEAD MACHINE (2) STRIKE PLATE KEY TURN MORTISE CYLINDER LOCK TRIM RING - /32 #0-2 x 3/4 FLAT HEAD TAPPING (2) SPACER BRACKET Page 3 of 28
= Inline Feature Strip = Half Feature Strip Connection Conditions.34" ~ (-/32") C L.34" ~ (-/32") C L NOTE: All other connection conditions are the same as standard panel mounting connection conditions. If a Floor Anchor is required C L C L. Using a pencil, mark floor anchor hole. 2. Using a masonry drill bit, drill a hole to the manufactures specification. Sliding Door Sliding Door Sliding Door 3. Place the anchor bolt into the hole. 4. Tap the anchor bolt down into the hole. "T" with Sliding Doors Centered 90 with Centered Sliding Door 5. Place anchor bracket over the anchor bolt and secure with washer & nut. 6. Tighten nut with wrench. NOTE: If floor anchoring is required on a raised floor, you can secure the anchor bracket to the floor with a screw and washer. 2 Anchor Bolt 3 4 5 6 Page 4 of 28
Installing The Frames. Install the slider door sidelite panel. Place top of panel into ceiling track first and then swing base of panel toward the floor. 2. Engage the post extension by inserting a screwdriver into the slots and slowly tapping the extension upward (2a) by engaging the small holes in the extension (2b). Extend fully to top of ceiling channel. 2b 2a SLIDER DOOR SIDELITE PANEL POST EXTENSION NOTE: Level frame before installing feature strips. NOTE: Adjoining frame removed from illustration for clarity. Page 5 of 28
Installing The Frames (continued) 3. Using two people, slide the transom height entryway into place. NOTE: For full height entryway unit see page 7 for assembly. TRANSOM HEIGHT ENTRYWAY Page 6 of 28
Assembling a Full Height Entry Frame STRIKE ENTRY HORIZONTAL ENTRY #0-6 x " PAN HEAD SCREWS VERTICAL ENTRY Page 7 of 28
Align track grooves Installing The Frames (continued) 4. Adjust levelers so that the tracks are align on both the sidelite frame and the entryway frame. CAUTION: Do not over tighten. 4 5. Secure the frames together with a full length feature strip or the optional vertical seal (see page 0). 3/32" ALLEN WRENCH 3/32" ALLEN WRENCH 4 4 Page 8 of 28
2a SIDE VIEW HEADER #0-24 x 3/8" SET SCREW Installing The Door Track Assembly. Align the track kit assembly with the frames. Butt end of track to vertical strike. 2. Attach track kit assembly to frames by engaging into track (2a) and secure using six (6) set screws with Loctite 425 (2b). VERTICAL STRIKE FRAME TRACK KIT TRACK KIT 2b /8" T-HANDLE ALLEN WRENCH TRANSOM HEIGHT SHOWN CAUTION: MAKE SURE THE TRACK IS SEATED AND SECURED TO HEADER WITH SET SCREWS AND LOCTITE 425, OTHERWISE INJURY MAY RESULT. HEADER /4" MAX ALONG TRACK AND HEADER TRACK Page 9 of 28
2b FEATURE STRIP Installing the Door Seal and the Optional Vertical Seal. Apply door seal to strike as shown. 2. For vertical seal option use vertical seal instead of feature strip on door side. Install as shown (2a). Use feature strip above track (2b). THIS STEP IS REQUIRED FOR FULL AND TRANSOM HEIGHT DOOR SEAL VERTICAL SEAL DOOR SEAL 2a TRANSOM HEIGHT SHOWN. FULL HEIGHT WILL HAVE THE DOOR SEAL AND THE VERTICAL SEAL GOING THE ENTIRE HEIGHT. TUCK DOOR SEAL BEHIND PLINTH TRIM J-HOOK PLINTH TRIM CUT TO JUST ABOVE J-HOOK J-HOOK Page 0 of 28
Installing the Roller Package Assembly HALF "A" FACES AWAY FROM PANEL 2 0 mm ( 3 ) 32 " 2.7 mm ( " 2 ) Check door thickness 3/8" (0mm) or /2" (2mm) ADD LOCTITE 425 TO THESE TWO (2) SCREWS 4 MM ALLEN WRENCH GLASS DOOR HALF "B" FACES PANEL SIDE OF DOOR LEAF 3 ROLLER 4 5 Side View BOLT INSTALL BOLT FLUSH TO TOP OF ROLLER CAUTION: Make sure "D" screws secure bolt as shown. Page of 28
STOP TRACK KIT 2 PANEL FRAME CHECK THAT BOLTS AND ROLLERS ARE FLUSH Installing The Door Assembly. Install one () stop into the track kit assembly as shown. Slide down to the opposite end and leave loose. 2. Install the glass door, use two people, and gently guiding the roller assemblies into the track kit assembly. SEE CAUTION! ROLLER TRACK KIT HALF "A" FACES AWAY FROM PANEL CAUTION: To avoid glass chipping, keep all protective corner packaging in place while unpacking and staging. Remove top protective corners after installing door leaf. Take care to avoid damage to unprotected corners. Do not rest bottom of glass on J-hook or other foreign objects. Page 2 of 28
STOP 3 TRACK KIT Installing The Door Assembly (continued) 3. Install the other stop into the track kit assembly as shown. 4. Adjust both stops so the door opens and closes at the correct distance. Edge of door to entryway (4a). Door should contact seal (4b). 5. Tighten the middle and outermost set screws per stop with Loctite 425. The innermost set screw, on the stop, will loosen or tighten the tension of the door as it rolls onto the stop. 4a 4b 5" MIN, 5-/2" MAX 5 ENTRYWAY POST DOOR HANDLE DOOR 3 MM ALLEN WRENCH INNERMOST SET SCREW Page 3 of 28
7 Installing The Door Assembly (continued) HALF "A" FACES AWAY FROM PANEL 6. Adjust roller package for door plumbness (6a). Maximum gap (6b). Secure bolt (6c). COVER CAP 7. Install cover caps. 8. Install track kit cover to sidelite end of the track kit assembly. Secure using provided screw. HALF "B" FACES PANEL GAP /2" MAX. 6a 6b Side View BOTTOM OF TRACK CAUTION: To adjust plumbness loosen "D" screw, but do not remove. TOP OF GLASS 8 TRACK KIT ADD LOCTITE 425 TO THESE TWO (2) SCREWS TRACK KIT COVER 6c CAUTION: Do not exceed max gap and make sure "D" screws secure bolt as shown or injury may result. Page 4 of 28
Installing The Door Assembly in a Tight Scenario. Slide stops and roller assemblies into each end of the track kit assembly and secure enough to not allow the rollers to come out. 2. Install track kit cover to sidelite end of the track kit assembly. Secure using provided screw. TRACK KIT CHECK THAT BOLTS AND ROLLERS ARE FLUSH 2 TRACK KIT COVER STOP ROLLER SIDELITE SIDE Page 5 of 28
2a SIDE VIEW HEADER Installing The Track Kit Assembly in a Tight Scenario. Align the track kit assembly with the frames. Butt end of track to vertical strike. 2. Attach track kit assembly to frames by engaging into track (2a) and secure using six (6) set screws with Loctite 425 (2b). 2b FRAME /8" T-HANDLE ALLEN WRENCH TRACK KIT TRACK KIT CAUTION: MAKE SURE THE TRACK IS SEATED AND SECURED TO HEADER WITH SET SCREWS AND LOCTITE 425, OTHERWISE INJURY MAY RESULT. HEADER /4" MAX ALONG TRACK AND HEADER TRACK Page 6 of 28
"D" SCREW Installing The Glass Door Assembly in a Tight Scenario. Install roller package assembly to the glass door per steps and 2 on page, except do not install (4) "D" screws. TRACK KIT BOLT HALF "A" FACES AWAY FROM PANEL GLASS DOOR 2a 2. Using two people, gently guide the glass door assembly into the track kit assembly (2a). Have third person position the bolts and once the door is hung add Loctite 425 to "D" screws and install. Do not tighten (2b). HALF "B" FACES PANEL 2b 4 MM ALLEN WRENCH CAUTION: To avoid glass chipping, keep all protective corner packaging in place while unpacking and staging. Remove top protective corners after installing door leaf. Take care to avoid damage to unprotected corners. Do not rest bottom of glass on J-hook or other foreign objects. GLASS DOOR Page 7 of 28
3 Installing The Glass Door Assembly in a Tight Scenario (continued) 3. Adjust both stops so the door opens and closes at the correct distance. 4. Tighten the middle and outermost set screws per stop with Loctite 425. Edge of door to entryway (4a). Door should contact seal (4b). The innermost set screw, on the stop, will loosen or tighten the tension of the door as it rolls onto the stop. 3 MM ALLEN WRENCH INNERMOST SET SCREW 5. Install cover caps. 5 4a 4b 5" MIN, 5-/2" MAX COVER CAP ENTRYWAY POST DOOR HANDLE DOOR Page 8 of 28
/2" GLASS RECEIVES ONE () SPACER PER SIDE 3/8" GLASS RECEIVES THREE (3) SPACER PER SIDE Installing the Base Channel. Align base rail assemblies to each side of glass door and attach using two (2) screws with Loctite 425. Only tighten screws enough to hold base rail assemblies from falling. NOTE: For a glass thickness of /2" use one () spacer per side. For 3/8" glass, use 3 (three) spacers per side. 2. Apply light seal to the back of each base channel in the location shown. SIDE VIEW TOP GLASS DOOR BASE RAIL 2 LIGHT SEALS ADDITIONAL SEALS FOR 3/8" GLASS ONLY BOTTOM LIGHT SEALS BASE CHANNELS Page 9 of 28
Installing the Base Channel (continued) 3. Start by sliding the rear base channel towards the strike side (3a) while also sliding the spline channel over the slider door guide assembly (3b) and also sliding the front base channel (3c). GLASS DOOR SIDE VIEW Advance the base channels and the spline channel until they are flush to the edge of the glass door. Align the base trim with the top of the plinth and the panel base. 3c 3b 3a FLUSH BASE RAIL PLINTH BOTTOM OF BASE RAIL FRONT BASE CHANNEL SPLINE CHANNEL REAR BASE CHANNEL APPROX. 2-3/6" SLIDER DOOR GUIDE FLOOR Page 20 of 28
Installing the Base Channel (continued) 4. Place base covers onto the ends of the base channels and secure with screws provided. 4 4 BASE COVER Page 2 of 28
Fix Leveler Position. Verify unit for plumb, square and level. 2. Adjust strike and leveler as required. 3. With countersink bit, drill hole and countersink the strike at pilot hole indicated. 4. Use #0-32 thread cutting screw to secure leveler position. ADJUSTMENT SET SCREWS /64th High Speed Drill #8 Countersink - McMaster - Carr #290A46 Optional Stop Collar - McMaster - Carr #2903A3 #0-32 X /2" FLAT HEAD THREAD CUTTING SCREW Page 22 of 28
Installing Plinths. Install base trims. Plinth Installation at strike side. Position 'L' shape strike plinth as shown. 2. Slide 'J' shape strike plinth into place. Plinth Removal at strike side. Pry 'L' and 'J' shape plinths apart at connection seam. 3. Press strike plinths together to lock assembly. 4 4. Trim and adhere seal, flush to top of plinth. 2 'L' SHAPE PLINTH 'J' SHAPE PLINTH Page 23 of 28
Top View - Sidelite Side Plinth Installation at sidelite side. Insert a plastic clip in each of door vertical. Plinth Removal at sidelite side. Slide sidelite plinth up from plastic clips, then pull back. 2. Locate and press sidelite plinth into place, engaging plastic clips. SIDELITE PLINTH PLASTIC CLIP SIDELITE PLINTH 2 PLASTIC CLIP SIDELITE PLINTH Page 24 of 28
Installing the Door Handle. Place the two (2) spacers into the holes on the glass door. 2. Install the plastic washers, steel washers and bolts onto the handle that has the threads inside the tubes as shown. 2 SPACER SCREW HANDLE WITH THREADS INSIDE TUBES PLASTIC WASHERS STEEL WASHERS COLLAR LOCK WASHER Page 25 of 28
SET SCREW 3/32" ALLEN WRENCH Installing the Door Handle (continued) 3. Place the handle with the clearance holes inside the tubes over the bolts. 4. Install the set screws on the upper (4a) and lower (4b) portion of the handle using Loctite 425. NOTE: Make sure the set screws are located on the bottom of the handle, so they are not visible to the customer. 3 4a 4b HANDLE WITH CLEARANCE HOLE INSIDE TUBES Page 26 of 28
Installing the Door Lock. Place the spacer bracket onto the lock assembly and install two (2) #8-32 x /4" flat head machine screws. Take note of the style of the set screws. They can be flat or hex. 2. If the glass is 3/8" thick, apply a lock pad on each side of the glass around the glass cutout as shown (2a). Place the block clamps inside the glass cutout (2b), then slide the lock assembly with spacer bracket inside the pockets of the block clamps (2c). 3. Slide the lock body channel up over the lock assembly with spacer bracket and line up the top and bottom holes with the holes on the block clamps. NOTE: The style of the set screws can be flat or hex. LOCK SPACER BRACKET 2b LOCK PAD - ONLY REQUIRED WHEN GLASS IS 3/8" THICK 2a BLOCK CLAMP LOCK WITH SPACER BRACKET 2c 3 LOCK BODY CHANNEL #8-32 x /4" FLAT HEAD MACHINE SCREW Page 27 of 28
5 THUMB TURN MORTISE CYLINDER 4 Installing the Door Lock (continued) 4. Install two (2) #8-8 x " flat head tapping screws. TRIM RING - /32" #8-8 x " FLAT HEAD TAPPING SCREW TRIM RING - /4" NOTE: This could be a small flat-bladed screwdriver or a allen drive wrench. 5. Place the /32" wide trim ring over the key turn mortise cylinder and install outside the office. Place the /4" wide trim ring over the thumb turn mortise cylinder and install inside the office. Check function of lock. Tighten the set screws to lock the cylinders in place. 6. Snap four (4) lock covers onto the top and bottom of the lock body channel. 7. Place the strike plate into the hole on the vertical strike and install two (2) #0-2 x 3/4" flat head tapping screws. Make sure seal is tucked under the strike plate at the top & bottom. LOCK COVER 6 KEY TURN MORTISE CYLINDER VERTICAL STRIKE #0-2 x 3/4" FLAT HEAD TAPPING SCREW STRIKE PLATE 7 SEAL Page 28 of 28