Skill Development Provider Accreditation Checklist Accrediting ETQA e.g. QCTO or SETA Name SDP Name: Centre Manager Name SDP Contact Details SDP Physical Address e.g. 17 Tonga-tinge Street, Mable Hall, 1612 Facilitator/Lecturer Name Facilitator/Trainer qualification relevant to the trade Auditor Name Auditor Employer Details Auditor Employer contact Ratio of learners to facilitator e.g. 12 Learners:1 Facilitator No. of Learners per given time in the Venue Accreditation History (If previously accredited through the SETA System, Complete the section below ) Accredited by: SETA Name Accreditation No. Accreditation Visit Date: DD/MM/CCYY OFO Code (if applicable) Province e.g. Northern Cape Municipality e.g. Madibeng New Accreditation Information Knowledge X Practical Skills X OFO Code Specialization /Alternative Title Legacy Trade New Trade SAQA ID Urban X Rural X Audit Visit Date DD/MM/YYYY Signature: Page 1 of 8 Date revised 23/02/2016
Hand Tools *Bolster 1:1 *Chalk line 1:2 *Line Blocks + Line / Builders Line 1:1 *Pencil 1:1 *Spade 1:4 *Straight Edges 1.5m, 2m, 2.5m & 4m 1:4 *Mortar boards 1:1 *Brick Trowel / Builders Trowel 1:1 *Plaster Trowel 1:1 *Gauging Trowel 1:1 *Brick Square 1:1 *Hammer 4 lb (4 Pound) / Club hammer 1:4 *Brick Hammer 1:4 *Rubber Mallet (Hammer) 1:4 *Wire brushes 1:4 *Bristle 1:4 *Cold chisel 1:1 *Plumb bob 1:10 *Pick with handle 1:4 *Rip saw 1:10 *Hack saw 1:10 *Shovel round 1:4 *Square nose 1:4 *Interior Corner Tool 1:1 *Exterior Corner Tool 1:1 *Nosing Tool 1:1 *Skirting Tool 1:1 Signature: Page 2 of 8 Date revised 23/02/2016
*Hand Hawk 1:1 *Float 1:1 *Corner float 1:1 *Steel trowel 1:1 *V-Jointer 1:1 *Reeding Tool (6 Groove) 1:1 *Plaster Square / Steel square 1:1 *Tool box 1:1 Special Tools *Dynamic Jointer (Wheels) 1:3 *Compass wing 1:5 *Jointer Square short 10 mm 1:5 *Jointer Square long 10 mm 1:5 *Jointer Round short 10 mm 1:5 *Jointer round long 10 mm 1:5 *Water level 1:10 *Dumpy level / Telescope 1:10 *Tripod 1:10 *Staff 1:10 Signature: Page 3 of 8 Date revised 23/02/2016
Assessment Aids *Segmental Arch Templates 1:5 *Semicircular Arch template 1:5 *Structure for Determining levels 1:5 *Concrete steps / form or ground for foundation 1:2 *Structure to be plastered (Depending on the Dimensions) 1:3 *Concrete floor 1 000 x 1 000 x 200mm risers 1:3 *Round column 2 100 x Radius 500mm 1:3 *Float surface 1 100 x 2 100mm 1:3 *Trowel finish wall 2 400 x 2 100mm 1:3 *Overhead concrete ceiling 900 x 900mm 1:1 *Recessed arch 610 x 2 100mm 1:2 Measuring Equipment *Tape measure 3m to 5m 1:1 *Tape measure 10m 1:5 *Ruler 1m 1:5 *Gauge rod 1:1 *Spirit level 1m - 1,2m 1:5 *Spirit level 600mm 800mm 1:5 Rain Gauge (Optional) Signature: Page 4 of 8 Date revised 23/02/2016
Machinery *Brick cutting machine 1:10 Demolishing machines (Optional) *Compactor 1:5 Power floating machine (Optional) 1:5 *Vibrator 1:5 Concrete mixer 1:5 Equipment (Long Term Consumables) *Scaffold Leg 2m *Scaffold Support 1.245 *Scaffold support 2.450 *Scaffold base jack *Scaffold connector *Trestle *Wooden doorframe Standard *Steel and Wooden window frame (NE8) *Vertical profile (Steel) *Scaffold plank *Wheel barrow *Face bricks *Wooden door frame 930mm outside measurement *Concrete lintels 1195x130x80mm *Concrete lintel 1195x100x80mm *Window sill Tiles 150x150x25mm Signature: Page 5 of 8 Date revised 23/02/2016
*Concrete Blocks 190x390x190mm *Window sill block 190x140 *Lintel blocks 190x390x190 *Steel pegs *Corner profile *Straight Edge 1m *Straight Edge 2m *Steel Clamps (4) Consumables *Wood Screws (3.5 X 20) *Bucket *Building Sand/River Sand (7 Wheel barrows full) *Lime (Minimum of 5 bags) *Stock Bricks *DPC 115mm; 220mm & 340mm *Line Pins *Nails *Wire for roof ties *Wall ties (bundle) *Stays Steel/Wood *Crimp wire *Arch Templates *Wire mash *Rhino lite Signature: Page 6 of 8 Date revised 23/02/2016
Safety *Apron 1:10 *Fire extinguishers *Personal Protective Clothing 1:1 *Safety Gloves 1:1 *Safety Boots 1:1 *Safety Goggles 1:1 *Safety helmet 1:1 *Respirator / Dust Mask 1:1 *First Aid box (Updated) *Evacuation plan in the workshop *Designated assembly point I, (manager of the trade test centre / skills development provider) hereby commits to comply with all the relevant OHS regulations and sections applicable to this specific trade. Signature and date Logistics And Lay-Out Demarcations Teaching Media Including Class Rooms For Theoretical Training 1:12 Green/White Boards/Notice Boards 1 P/C Projectors Models samples Stationery Area for setting out buildings Ventilation Lighting Workshop or slab for practical components Signature: Page 7 of 8 Date revised 23/02/2016
Cubicles Proportional to the Number of Candidates I. the undersigned, hereby declare that all the tools/equipment/training materials/machines were checked and are the sole property of the SDP. Signature:.. Date: Accreditation recommended Yes No Constraints/Gaps: Recommendations: SME Name Signature Date: DD/MM/CCYY Organizational Rep. Name Designation Signature Date DD/MM/CCYY Signature: Page 8 of 8 Date revised 23/02/2016