Finish face milling tools FMA08 FMP04 FMDX series series series
FMA08/FMP04 Finish face milling tools series With general wiper inserts, flexible match, for different working conditions General finish milling FMA08
Arc General wiper insert Module adjustment Compact FMP04 Interference or low axial force machining 1
Clamping screw FMA08 SERIES Holder clamping screw Tightening screw With highly economical ON inserts, 16 edges available, XEEC 12090 high precision wiper inserts, 4 edges available. Available cutting length of wiper inserts is 7.3mm, allowing for more demanding cycle time Modular finish machining holder, precise adjustment, flexible use, satisfying 0.002mm adjustment resolution First choice for wide open face machining, with higher requirements on system rigidity, for cylinder block top, bottom, front and rear end face machining
machining case Machining engine block cover, material CGI, HB220, wet cutting, Ra 1.6 Cutting data: Vc=175m/min, F=1000mm/min, ap=0.5mm Company Cutting insert Wiper insert ZCC CT FMA08-125-B40-ON06-15W3 ONHU060408-CM/YBD152 XEEC120904/YBG105 Company A Similar products edge life 350 pcs 100 pcs Comparison of single edge life No. of machined workpiece (pc) Result of experiment: Under same cutting data, our FMA08 has superior single edge life than similar paroducts of Company A. Company A
FMA08 adjustable finish milling tools Kr:45 o type interface 1 type interface 1 type interface 1 specification Stock Basic dimension (mm) ØD ØD1 ød L apmax No. of teeth Interface style Weight -100-B32-ON06-12W2 100 111.1 32 63 1.0 10+2 B 3.0-125-B40-ON06-15W3 125 136.1 40 63 1.0 12+3 B 4.5 FMA08-160-C40-ON06-18W3 160 171.1 40 63 1.0 15+3 C 6.8-200-C60-ON06-24W4 200 211.1 60 63 1.0 20+4 C 10.3-250-C60-ON06-30W5 250 261.1 60 63 1.0 25+5 C 15.1-315-D60-ON06-36W6 315 326.1 60 80 1.0 30+6 D 27.2 in stock made to order accesaries diameter ØD Insert Holser block screw wrench toolholder Ø100-Ø315 diameter ØD ONHU060408-CM W18N DM6 20A WT15IS -- XEEC120904 -- -- WH50L LOCATOR-XEEC12 Insert Holder clamping screw screw screw Adjustment block Ø100-Ø315 ONHU060408-CM -- -- -- -- XEEC120904 M6 18(GB70-85) I60M4 10 DM6 20A ADJ01
FMA08 adjustable finish milling tools selection 45 d Basic demension (mm) CVD coating PVD coating ceramic carbide Insert shape L ØI.C S ød r YBC301 YBC302 YBM251 YBM253 YBM351 YBD152 YBD252 YBG105 YBG202 YBG205 YBG302 YBG152 YBG252 YNG151 YNG151C YC30S YD051 YD101 YD201 ONHU060408-CM 6.58 15.875 4.76 4.4 0.8 recommended optional made to order grade in stock grade in stock W bs d Basic demension (mm) CVD coating PVD coating ceramic carbide L Insert shape specification L W S ød bs YBC301 YBC302 YBM251 YBM253 YBM351 YBD152 YBD252 YBG105 YBG202 YBG205 YBG302 YBG152 YBG252 YNG151 YNG151C YC30S YD051 YD101 YD201 XEEC120904 12.7 9.525 4.76 4.4 7.3 recommended optional made to order grade in stock grade in stock Recommended cutting data Workpiece material Hardness HB Insert grade V(m/min) Cutting daata f(mm/z) 180-260 K Cast iron YBD152 250(150-300) 0.06~0.25 YBG105 180(100-250) 0.06~0.25
SERIES Non-adjustable tool Adjustable tool entering angle, low axial force, first choice for thin-wall parts, low rigidity clamping, satisfying semi-finish and finish machining combined Compact tool design, closer machining, avoiding interference and guarantying surface quality With SNCU series cutting edge, max cutting depth 9.8mm High precision modular adjustment holder, with XEEC120904 4-edge wiper inserts
Wiper insert Max cutting depth 9.8mm Cutting insert machining case Engine block filter face machining Company Cutting insert Wiper insert Cutting data ZCC CT FMP04-200-C60-SN12-24W4 SNCU120412-CF/YBD152 XEEC120904/YBD152 Vc=250m/min, F=1000mm/min, ap=0.3mm Company A Similar products Vc=216m/min, F=480mm/min, ap=0.3mm Cutting speed (m/min) Surface quality FMP04 Excellent Company A ordinary High efficiency Result: Under high speed cutting conditions, our FMP04 series products present better machining efficiency and surface quality than similar products of company A, which means superior performance.
FMP04 non-adjustable finish milling tools Kr:88 o type interface type interface 1 1 type interface 1 specification Stock Basic dimension (mm) ØD ØD1 ød L apmax No. of teeth Interface style Weight -050-A22-SN12-04 50 51.3 22 40 9.8 4 A 0.46-063-A22-SN12-06 63 64.3 22 40 9.8 6 A 0.55-080-A27-SN12-08 80 81.3 27 50 9.8 8 A 1.1 FMP04-100-B32-SN12-10 100 101.3 32 50 9.8 10 B 1.4-125-B40-SN12-11 125 126.3 40 63 9.8 11 B 3.2-160-C40-SN12-14 160 161.3 40 63 9.8 14 C 4.0-200-C60-SN12-16 200 201.2 60 63 9.8 16 C 6.5-250-C60-SN12-18 250 251.2 60 63 9.8 18 C 11.5 in stock made to order
FMP04 non-adjustable finish milling tools accesaries diameter ØD Insert clamping screw Wrench Ø50-Ø250 SNCU1204- I60M4 10 WT15IT
FMP04 non-adjustable finish milling tools Kr:88 o type interface type interface 1 1 type interface 1 specification Stock Basic dimension (mm) ØD ØD1 ød L apmax No. of teeth Interface style Weight -063-A22-SN12-08 63 64.3 22 40 9.8 8 A 0.6-080-A27-SN12-11 80 81.3 27 50 9.8 11 A 1.3-100-B32-SN12-14 100 101.3 32 50 9.8 14 B 1.55 FMP04-125-B40-SN12-18 125 126.3 40 63 9.8 18 B 3.5-160-C40-SN12-22 160 161.3 40 63 9.8 22 C 4.5-200-C60-SN12-28 200 200.3 60 63 9.8 28 C 6.6-250-C60-SN12-36 250 251.2 60 63 9.8 36 C 13.0 in stock made to order accesaries diameter ØD Insert Block Screw Wrench Ø63-Ø250 SNCU1204- W18N DM6 20A WT15IT
FMP04 non-adjustable finish milling tools Insert selection for non-adjustable finishing tools bs Basic demension (mm) CVD coating PVD coating ceramic carbide Insert shape L ØI.C S ød r bs YBC301 YBC302 YBM251 YBM253 YBM351 YBD152 YBD252 YBG102 YBG105 YBG202 YBG205 YBG302 YBG152 YBG252 YNG151 YNG151C YC30S YD051 YD101 YD201 SNCU120412-CM 12.7 12.7 4.76 4.68 1.2 1.5 SNCU120412-CF 12.7 12.7 4.76 4.68 1.2 1.5 SNCU1204-W 12.7 12.7 4.76 4.68 -- 4.0 recommended optional made to order grade in stock grade in stock Recommended cutting data for non-adjustable finishing tools Workpiece material P Low carbon steel soft steel High carbon steel alloy steel Alloy tool steel Hardness HB Cast iron 180-260 K Insert grade V(m/min) Cutting daata f(mm/z) 180 YBC302 230(170-350) 0.2(0.1-0.3) 180-280 YBC302 220(150-330) 0.2(0.1-0.3) 280-350 YBC302 190(130-300) 0.2(0.1-0.3) YBG102 210(120-300) 0.2(0.1-0.25) YBD252 200(150-250) 0.3(0.1-0.4) YBD152 250(150-300) 0.2(0.1-0.3)
FMP04 non-adjustable finish milling tools Kr:88 o type interface type interface 1 1 specification Stock Basic dimension (mm) ØD ØD1 ød L apmax No. of teeth Interface style Weight -125-B40-SN12-15W3 125 126.2 40 63 9.8 12+3 B 3.9 FMP04-160-C40-SN12-18W3 160 161.2 40 63 9.8 15+3 C 6.5-200-C60-SN12-24W4 200 201.2 60 63 9.8 20+4 C 9.9 in stock made to order Accesaries of adjustable finishing tool diameter ØD Insert Block Screw Wrench holder Ø125-Ø200 diameter ØD SNCU120412- W18N DM6 20A WT15IS -- XEEC120904 WH50L LACATOR-XEEC12 Insert Holder clamping screw Screw Screw Adjustment block Ø125-Ø200 SNCU120412- -- -- -- -- XEEC120904 M6 18(GB70-85) I60M4 10 DM6 20A ADJ01
FMP04 non-adjustable finish milling tools selection for adjustable finishing tool bs Basic demension (mm) CVD coating PVD coating ceramic carbide Insert shape L ØI.C S ød r bs YBC301 YBC302 YBM251 YBM253 YBM351 YBD152 YBD252 YBG102 YBG105 YBG202 YBG205 YBG302 YBG152 YBG252 YNG151 YNG151C YC30S YD051 YD101 YD201 SNCU120412-CM 12.7 12.7 4.76 4.68 1.2 1.5 SNCU120412-CF 12.7 12.7 4.76 4.68 1.2 1.5 recommended optional made to order grade in stock grade in stock bs d Basic demension (mm) CVD coating PVD coating ceramic carbide L Insert shape L ØI.C S ød bs YBC301 YBC302 YBM251 YBM253 YBM351 YBD152 YBD252 YBG102 YBG105 YBG202 YBG205 YBG302 YBG152 YBG252 YNG151 YNG151C YC30S YD051 YD101 YD201 XEEC120904 12.7 9.525 4.76 4.4 7.3 recommended optional made to order grade in stock grade in stock Recommended cutting data for adjustable finishing tool Workpiece material Hardness HB Insert grade V(m/min) Cutting daata f(mm/z) Cast iron 180-260 K YBD252 200(150-250) 0.06-0.25 YBD152 250(150-300) 0.06-0.25 YBG105 180(100-250) 0.06-0.25
GNEY SERIES Finishing tool Wiper insert Left or right insert both applicable Wipe edger up to 6mm 4 wiper edge for 1 insert For larger cutting depth Optimized tool geometry and technical structure Rough and finish insert share the same slot, screw clamping locating face Self-correcting mounting structure
As FMD02 supplement series, more suitable for small cutting depth, finishing Ra 1.6 with wiper inserts Screw clamping, tool does not need to be removed from machine, convenient online mounting available Wiper inserts and cutting edges share the same slot, saving cost Easy mounting of wiper inserts, easy identification, reducing error Cutting insert machining case Automobile mold rear finish milling, material FCD540, HB220, dry cutting, Ra1.6 Cutting data: N=800 r/min, F=1000mm/min, ap=0.1mm Company Cutting insert Wiper insert Cutting data ZCC CT FMDX-125-B40-PN11-12 PNEG110512R-CM/YBD152 PNEG1105-PW6/YBD152 500min Company A Similar products 300~400min Company A Result: Producing no abnormal noise during cutting, in comparison with similar products of Company A, under same cutting data, our FMDX series have longer service life, more excellent wear resistance of insert, with dimension precision satisfying customer requirements, stable tool life.
FMDX non-adjustable finish milling tools Kr:67 o type interface type interface 1 1 type interface 1 specification Stock Basic dimension (mm) ØD ØD1 ød L apmax No. of teeth Interface style Weight -080-A27-PN11-08 80 90.1 27 50 5 8 A 1.2-100-B32-PN11-10 100 110.1 32 50 5 10 B 1.6 FMDX -125-B40-PN11-12 125 135.1 40 63 5 12 B 3.3-160-C40-PN11-14 160 170.1 40 63 5 14 C 4.9-200-C60-PN11-16 200 210.1 60 63 5 16 C 8.2-250-C60-PN11-18 250 250.1 60 63 5 18 C 12.4 in stock made to order accesaries diameter ØD Insert Insert tightening screw Wrench Ø80-Ø250 PNEG1105- I60M4 10 W15IT
FMDX non-adjustable finish milling tools Insert selection Basic demension (mm) CVD coating PVD coating carbide Insert shape L ØI.C S ød bs YBC301 YBC302 YBM251 YBM253 YBM351 YBD152 YBD252 YBG105 YBG202 YBG205 YBG302 YBG152 YBG252 YNG151 YNG151C YC30S YD051 YD101 YD201 PNEG110512R/L-CF 5.4 15.875 5.56 4.64 1.6 PNEG110512R/L-CM 5.4 15.875 5.56 4.64 1.6 PNEG110512R/L-CR 5.4 15.875 5.56 4.64 1.6 recommended optional made to order grade in stock grade in stock Basic demension (mm) CVD coating PVD coating ceramic ceramic carbide Insert shape L ØI.C S ød bs YBC301 YBC302 YBM251 YBM253 YBM351 YBD152 YBD252 YBG105 YBG202 YBG205 YBG302 YBG152 YBG252 YNG151 YNG151C YC30S YD051 YD101 YD201 PNEG1105-PW6 5.4 15.875 5.56 4.64 6.0 recommended optional made to order grade in stock grade in stock Recommended cutting data Workpiece material Hardness HB Insert grade V(m/min) Cutting daata f(mm/z) P Low carbon steel soft steel High carbon steel alloy steel 180 180-280 YBC301 270(220-350) 0.2(0.1-0.3) YBC302 230(170-350) 0.2(0.1-0.3) YBC301 240(200-320) 0.15(0.1-0.3) YBC302 220(150-330) 0.2(0.1-0.3) Alloy tool steel 280-350 YBC301 220(180-300) 0.15(0.1-0.3) YBC302 190(130-300) 0.2(0.1-0.3) Cast iron 180-260 K YBD152 270(150-300) 0.2(0.1-0.3) YBD252 200(150-250) 0.3(0.1-0.4) YBG105 180(120-300) 0.2(0.1-0.25)