iniature photoelectric switches series W-: The efficient space savers Photoelectric reflex switch with switching threshold adaptation and autocollimation. Transparent objects of all kinds can be reliably detected in difficult and changing ambient conditions, with the switching threshold being automatically adapted to the changing ambient conditions, such as dust gathering on the optical surfaces. D ATA SH E E T Photoelectric proximity switches BGS Photoelectric reflex switches Through-beam photoelectric switches IIt is the little things that make you big : minimum size, maximum versatility. Three versions of the W- series offer the users the following benefits for their application: Clearly visible light spot. The integration of new pinpoint LEDs creates brilliant, tightly defined light spots. Thus, the photoelectric switches can be aligned easily and quickly, as the light spot is easy to see even in bright ambient conditions. Best background suppression in its class. Background suppression offering more than just a good black/white displacement, i. e. object detection in front of reflective and moving backgrounds. The sensor has a nd sender LED allowing the sensor to see spatially. Optimum ambient light suppression. The photoelectric proximity switch needs to detect objects directly in front of an energy-saving lamp or a fluorescent lamp no problem. Light from such sources is identified and suppressed. Hygienic and safe to use in aggressive environments. Hydrofluoric acid, coolants, alcohols etc. cannot affect the fully Teflon-encapsulated versions even when exposed for long periods.
W- Selection table Reliably solved with linear light spot featured in the WTB-: Continuous detection of honeycomb structured objects, Accurate positioning, irrespective of grooves or recesses in objects, Reliable detection of falling objects. WTB- Photoelectric proximity switch with background suppression Detection of objects, irrespective of colour and consistency, up to the predefined scanning distance Best background suppression Clearly visible light spot Photoelectric proximity switch WTBS- with laser-like light spot: detection of the inserted PC board, at a distance of 80 mm, with pinpoint accuracy. The reflecting background does not interfere with the sensor s performance if no tool carrier is clamped and the robot moves. Laser-like light spot in the WTBS- for: Accurate positioning of the light beam on the object, Reliable detection of small objects immediately in front of a background, Very good visibility of the light spot on the object. WL- and WLG- Photoelectric reflex switches Safe and easy mounting. The mounting holes are fitted with threaded metal bushes for added strength. uick and easy alignment using the clearly visible light spot. Detection of transparent objects with switching threshold adaptation. Photoelectric reflex switch WLGS- thinks and controls with: automatic switching threshold adaptation transparent objects with an attenuation of > 8% are reliably detected. Detection of transparent objects such as PET bottles, even with dust and moisture present, Implementation of the sensor close to the process, without expensive mounting systems, Clear visibility of the light spot aids the alignment of the sensor, from nearly all conceivable positions. WSE- Through-beam photoelectric switches Fast and reliable alignment of the sensors through brilliant light spot. SICK 008-0-0
Housing Version Light beam geometry Description Side view Slim housing Standard photoelectric proximity switch Scanning distance:... 0 mm. mm in 0 mm For standard applications: packaging, paper, cardboard, PC boards, solar cells. Page to Laser-like Scanning distance:... 0 mm < mm of 0 mm to 80 mm Detection and positioning of small parts and any object directly in front of a background. to Standard photoelectric proximity switch Scanning distance:... 0 mm 7 mm in 0 mm For standard applications: detection of packaging, paper, cardboard, PC boards, solar cells etc. to 7 V-optics Scanning distance:... 0 mm 0 mm in 0 mm Detection of transparent and reflective objects: e. g. transparent trays, shiny packages, blister packs. 8 to 9 Line sensor Scanning distance:... 0 mm x 8 mm in 0 mm Detection of structured objects: grid boxes, PC boards with gaps, monitoring of small ejected parts. 0 to Standard sensor in Teflon housing Scanning distance:... 0 mm 7 mm in 0 mm Detection of objects in harsh ambient conditions or directly in contact with liquids. H O -compatible. to Side view Slim housing Autocollimation with polarisation filter Range: 0.0... m mm in. m Photoelectric switch for glass detection with switching threshold adaptation Range: 0.0... m Standard with polarisation filter Range: 0.0... m Photoelectric switch for glass detection Range: 0.0... m mm in. m 7 mm in. m Small, high visibility light spot for the detection of small objects and where mounting space is restricted. Detection of transparent objects. Compensation for environmental effects such as temperature fluctuations, dust and dirt. For standard applications: With and without Teach-in function, sec. Teach for 0 % switching threshold. 8 sec. long Teach for transparent objects with > 8 % attenuation. 80 mm in. m Detection of PET bottles and foils > 8 % attenuation and of objects with critical shiny surfaces such as foil packaging and coffee packages. to 7 8 to 9 0 to to Side view Slim housing Range: 0... m 0 mm in.0 m Detection of small parts, advantageous for applications where space is restricted and where reflective surfaces are present. to 7 Range: 0... m 0 mm in.0 m For standard applications: sender with test input. 8 to 9 Teflon housing Range: 0... m 0 mm in.0 m Detection of objects in harsh ambient conditions or directly in contact with liquids. H O -compatible. 0 to 008-0-0 SICK
Photoelectric proximity switch, WTBS-, BGS, red light, potentiometer Scanning distance... 80 mm Photoelectric proximity switch Dimensional drawing. 7. Highly accurate adjustment of the scanning distance with -turn potentiometer Outstandingly visible and tightly defined light spot Robust mounting thanks to metal bushes 8 7.7 0.9 9.8 8.8 7 Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator green, power on LED indicator yellow, status of received light beam Potentiometer 7 ounting hole 8 Connector WTBS-F WTBS-N WTBS-P WTBS-P WTBS-P WTBS-E WTBS-N WTBS-P See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems 8, -pin 8, -pin 8, -pin x 0. mm² SICK 008-0-0
W- WTBS- E F N N P P P P Scanning distance typ. max. Operating distance Adjustment of operating distance... 80 mm 0... 80 mm Potentiometer, revolutions Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter. mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, PNP antivalent Dark-switching Light-switching Complementary 00 ma Response time < 0. s ) Switching frequency,000 Hz ) Cable, PVC, m 7) VDE protection class Connector, 8, -pin Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 7) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Novodur, PA ) Average service life 00,000 h at Ta = + C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Scanning distance 0 80 0 80 0 80 0 (mm) 90 80 Operating distance Scanning distance typ. max. Scanning distance on black, % remission Scanning distance on grey, 8 % remission Scanning distance on white, 90 % remission % of scanning distance 0 0 0 0 (mm) 0 00 0 80 Ordering information WTBS-E 007 WTBS-F 00 WTBS-N 00 WTBS-N 00 WTBS-P 00 WTBS-P 000 WTBS-P 00 WTBS-P 00 008-0-0 SICK
Photoelectric proximity switch, WTBS-, BGS, red light, focussed, potentiometer Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing. 7. Highly accurate adjustment of the scanning distance with -turn potentiometer Easily visible laser-type light spot Robust mounting thanks to metal bushes 8 7.7 0.9 9.8 7 8.8 Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator green, power on LED indicator yellow, status of received light beam Potentiometer 7 ounting hole 8 Connector WTBS-E WTBS-N WTBS-P WTBS-P WTBS-P WTBS-F WTBS-N WTBS-P x 0. mm² 8, -pin 8, -pin 8, -pin See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems WTBS-N x 0. mm² SICK 008-0-0
W- WTBS- E F N N N P P P P Scanning distance typ. max. Operating distance Adjustment of operating distance... 0 mm 0... 0 mm Potentiometer, revolutions Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter. mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, NPN antivalent PNP antivalent Dark-switching Complementary Light-switching 00 ma Response time < 0. s ) Switching frequency,000 Hz ) Cable, PVC, m 7) VDE protection class Connector, 8, -pin Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 7) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Novodur, PA ) Average service life 00,000 h at Ta = + C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Scanning distance 0 0 0 0 0 0 0 (mm) 0 0 0 80 00 0 Operating distance Scanning distance typ. max. Scanning distance on black, % remission Scanning distance on grey, 8 % remission Scanning distance on white, 90 % remission % of scanning distance 0 0 0 0 (mm) 0 0 0 80 00 0 Ordering information WTBS-E 00 WTBS-F 000 WTBS-N 00 WTBS-N 00 WTBS-N 00 WTBS-P 009 WTBS-P 00 WTBS-P 007 WTBS-P 008 008-0-0 SICK 7
Photoelectric proximity switch, WTBS-, BGS, red light, focussed, teach-in Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing. A 7. A Easy commissioning through teach-in function Easily visible laser-type light spot Robust mounting thanks to metal bushes 7.7 0.9 9 8.8 7 8.8 Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator green, power on LED indicator yellow, status of received light beam Teach-in button 7 ounting hole 8 Connector WTBS-N WTBS-N WTBS-P WTBS-P x 0, mm² x 0, mm² 8, -pin 8, -pin ET ET WTBS-P WTBS-P See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems 8, -pin 8, -pin ET 8 SICK 008-0-0
W- WTBS- N N P P P P Scanning distance typ. max. Operating distance... 0 mm 0... 0 mm Adjustment of operating distance Teach-in: single-teach button & cable ) Teach-in: single-teach button Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter. mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, Light-switching 00 ma Response time < 0. ms ) Switching frequency,000 Hz 7) Cable, PVC, m 8) VDE protection class Connector, 8, -pin Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 8) Cable with plug, 8, -pin, PVC, 00 mm 8) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) External teach-in: impuls > s with voltage Vs for PNP or for NPN ) Average service life 00,000 h at Ta=+ C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load 7) With light/dark ratio : 8) Do not bend below 0 C Scanning distance 0 0 0 0 0 0 0 (mm) 0 0 0 80 00 0 Operating distance Scanning distance typ. max. Scanning distance on black, % remission Scanning distance on grey, 8 % remission Scanning distance on white, 90 % remission % of scanning distance 0 0 0 0 (mm) 0 0 0 80 00 0 Order information WTBS-N 00 WTBS-N 00 WTBS-P 00 WTBS-P 000 WTBS-P 00 WTBS-P 00 008-0-0 SICK 9
Photoelectric proximity switch, WTBS-, BGS, focussed, IO-Link, teach-in Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing. 7. Parameterisation and diagnostics via IO-Link Easily visible laser-type light spot 7.7 9 Robust mounting thanks to 0.9 metal bushes 8.8 7 8.8 Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator green, power on LED indicator yellow, status of received light beam Teach button 7 ounting hole 8 Connector WTBSC-P WTBSC-P See Accessories chapter Connector,, -pin Connector, 8, -pin ounting systems 8, -pin /C, -pin /C 0 SICK 008-0-0
W- WTBSC- P P Scanning distance typ. max. Operating distance... 0 mm 0... 0 mm Adjustment of operating distance Teach-in: single-teach button Teach-in: via IO-Link Communication mode CO Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter. mm at 0 mm distance Supply voltage V s DC 8... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs PNP, /C PNP, not Switching mode Light-switching ) Output current I a max < 00 ma Response time < 0. ms ) Switching frequency,000 Hz 7) Connector, 8, -pin Cable with plug,, -pin, PVC, 0 mm 8) VDE protection class Circuit protection V s connections reverse-polarity protected / All outputs short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Parametrisable via IO-Link ) Signal transit time with resistive load in switching mode. Different values possible in CO mode. 7) With light/dark ratio : in switching mode. Different values possible in CO mode. 8) Do not bend below 0 C Scanning distance 0 0 0 0 0 0 0 Ordering information WTBSC-P 009 WTBSC-P 008 0 (mm) 0 0 0 80 00 0 Operating distance Scanning distance typ. max. Scanning distance on black, % remission Scanning distance on grey, 8 % remission Scanning distance on white, 90 % remission % of scanning distance 0 0 0 (mm) 0 0 0 80 00 0 008-0-0 SICK
Photoelectric proximity switch, WTB-, BGS, red light, potentiometer Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing High-precision setting of scanning distance thanks to -turn potentiometer Object detection almost irrespective of colour and background consistency Secure function when mounted opposite other sensors 9. 8 8. 0.9 7. 7 9. Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator yellow, status of received light beam LED indicator green, power on Potentiometer 7 ounting hole 8 Connector WTB-P WTB-N WTB-F WTB-N WTB-P WTB-F WTB-P x 0. mm² 8, -pin 8, -pin See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems WTB-N x 0. mm² WTB-P 8, -pin WTB-P 8, -pin SICK 008-0-0
W- WTB- F F N N N P P P P P Scanning distance typ. max. Operating distance Adjustment of operating distance... 0 mm... 0 mm Potentiometer, revolutions Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 7 mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max PNP, NPN antivalent NPN, PNP antivalent Dark-switching Complementary Light-switching 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) VDE protection class Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 7) Cable, PVC, m 7) Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 7) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Scanning distance 0 0 0 0 (mm) Operating distance 0 7 00 0 Scanning distance, max. typical Scanning range on black, % remission Scanning range on grey, 8 % remission Scanning range on white, 90 % remission % of scanning distance %/90% 0 0 8%/90% 90%/90% 0 (mm) 0 7 00 0 Ordering information WTB-F 0807 WTB-F 080 WTB-N 080 WTB-N 080 WTB-N 080 WTB-P 0809 WTB-P 08099 WTB-P 0800 WTB-P 08097 WTB-P 08098 Additional types on request 008-0-0 SICK
Photoelectric proximity switch, WTB-, BGS, red light, teach-in Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing Commissioning by simple teach-in function Object detection almost irrespective of colour and background consistency Secure function when mounted opposite other sensors 9. 8 8. 0.9 7. 7 9 Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator yellow, status of received light beam LED indicator green, power on Teach button 7 ounting hole 8 Connector WTB-N WTB-P WTB-P WTB-N WTB-P WTB-N WTB-P x 0. mm² 8, -pin 8, -pin 8, -pin ET See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems WTB-N WTB-P x 0. mm² WTB-P 8, -pin ET SICK 008-0-0
W- WTB- N N N N P P P P P P Scanning distance typ. max. Operating distance... 0 mm... 0 mm Adjustment of operating distance Teach-in: single-teach button & cable ) Teach-in: single-teach button Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 7 mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, PNP antivalent Light-switching Complementary 00 ma Response time < 0. ms ) Switching frequency,000 Hz 7) Cable, PVC, m 8) VDE protection class Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 8) Connector, 8, -pin Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) External teach-in: impuls > s with voltage V s for PNP or for NPN ) Average service life 00,000 h at Ta = + C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load 7) With light/dark ratio : 8) Do not bend below 0 C Scanning distance 0 0 0 0 (mm) Operating distance 0 7 00 0 Scanning distance, max. typical Scanning range on black, % remission Scanning range on grey, 8 % remission Scanning range on white, 90 % remission % of scanning distance %/90% 0 0 8%/90% 90%/90% 0 (mm) 0 7 00 0 Ordering information WTB-N 08090 WTB-N 08087 WTB-N 08088 WTB-N 08089 WTB-P 0890 WTB-P 0808 WTB-P 0808 WTB-P 0808 WTB-P 0808 WTB-P 0808 Additional types on request 008-0-0 SICK
Photoelectric proximity switch, WTB-, BGS, IO-Link, teach-in Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing Object detection almost irrespective of colour and background consistency Reliable operation if devices are installed opposite each other 9. 8. 0.9 7. Commissioning through simple teach-in function or IO-Link 8 7 Parameters and diagnostics via 9 IO-Link Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator yellow, status of received light beam LED indicator green, power on Teach button 7 ounting hole 8 Connector WTBC-P WTBC-P 8, -pin, -pin See Accessories chapter Connector,, -pin Connector, 8, -pin ounting systems /C /C SICK 008-0-0
W- WTBC- P P Scanning distance typ. max. Operating distance... 0 mm... 0 mm Adjustment of operating distance Teach-in: single-teach button Teach-in: via IO-Link Communication mode CO Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 7 mm at 0 mm distance Supply voltage V s DC 8... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs PNP, /C PNP, not Switching mode Light-switching ) Output current I a max < 00 ma Response time < 0. ms ) Switching frequency,000 Hz 7) Connector, 8, -pin Cable with plug,, -pin, PVC, 00 mm 8) VDE protection class Circuit protection V s connections reverse-polarity protected / All outputs short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Parametrisable via IO-Link ) Signal transit time with resistive load in switching mode. Different values possible in CO mode. 7) With light/dark ratio : in switching mode. Different values possible in CO mode. 8) Do not bend below 0 C Scanning distance 0 0 0 0 %/90% Ordering information WTBC-P 0809 WTBC-P 009 0 (mm) Operating distance 0 7 00 0 Scanning distance, max. typical Scanning range on black, % remission Scanning range on grey, 8 % remission Scanning range on white, 90 % remission % of scanning distance 0 8%/90% 90%/90% 0 (mm) 0 7 00 0 008-0-0 SICK 7
Photoelectric proximity switch, WTV-, BGS, red and infrared light, V-optics Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing Reliable detection of highly transparent and shiny objects at a distance of 0... mm High-precision setting of scanning distance thanks to -turn potentiometer Large, homogeneous light spot 9. 8 8. 0.9 7. 7 9. Adjustments possible Standard direction of the material being scanned Optical axis, receiver Optical axis, sender LED indicator yellow, status of received light beam LED indicator green, power on Potentiometer 7 ounting hole 8 Connector WTV-P WTV-P WTV-N WTV-P WTV-P WTV-N WTV-P WTV-P 8, -pin 8, -pin 8, -pin x 0. mm² See Accessories chapter Connector,, -pin Connector, 8, -pin Connector, 8, -pin ounting systems WTV-P, -pin 8 SICK 008-0-0
W- WTV- N N P P P P P P P Scanning distance typ. max. Operating distance Adjustment of operating distance... 0 mm... 0 mm Potentiometer, revolutions Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter Pinpoint LED, infrared light, 880 nm ) 0 mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, PNP antivalent Light-switching Complementary 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Cable, PVC, m 7) VDE protection class Circuit protection Connector, 8, -pin Connector, 8, -pin Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values Cable with plug, 8, -pin, PVC, 00 mm Cable with plug,, -pin, PVC, 0 mm V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Black-white shift/distance to background Background 0 0 0 0 0 [mm] 0 0 0 0 0 Distance Ordering information WTV-N 08 WTV-N 08 WTV-P 09888 WTV-P 08 WTV-P 08 WTV-P 08 WTV-P 09 WTV-P 08 WTV-P 098 Black-white shift 90 %/ % Distance to background detecting transparent objects 008-0-0 SICK 9
Photoelectric proximity switch, WTB-, BGS, red light, line Scanning distance... 0 mm Photoelectric proximity switch Dimensional drawing Wide-angle light spot with an aperture of 0 Reliable detection of objects with slots and holes Reliable detection of grid structures 9. 8 8. 0.9 7. 7 9. Adjustments possible Direction of the sender light line Optical axis, sender Optical axis, receiver LED indicator yellow, status of received light beam LED indicator green, power on Potentiometer 7 ounting hole 8 Connector WTB-N7 WTB-P7 WTB-N7 WTB-P7 WTB-P7 WTB-N7 WTB-P7 8, -pin 8, -pin 8, -pin x 0. mm² See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems 0 SICK 008-0-0
W- WTB- N7 N7 N7 P7 P7 P7 P7 Scanning distance typ. max. Operating distance Adjustment of operating distance... 0 mm... 0 mm Potentiometer, revolutions Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter x 8 mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, PNP antivalent Light-switching Complementary 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Cable, PVC, m 7) VDE protection class Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 7) Connector, 8, -pin Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values Scanning distance and light spot width ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C 0 0 0 (mm) 0 7 0 Scanning range on white, 90 % reflectance Scanning range on black, % reflectance inimum detectable object Lightspot: line width 70 0 0 0 0 0 0 0 [mm] 0 0 0 80 00 0 Distance Ordering information WTB-N7 08 WTB-N7 08 WTB-N7 077 WTB-P7 08 WTB-P7 08 WTB-P7 090 WTB-P7 08 adjusted scanning distance 0 mm adjusted scanning distance 00 mm 0 % 0 % 8 8 Width of object 90 % 0 [mm] 0 0 0 0 0 0 Distance to object Width of object 90 % 0 [mm] 0 0 00 Distance to object 008-0-0 SICK
Photoelectric proximity switch, WTB-, BGS, red light, in Teflon housing Scanning distance... 0 mm Dimensional drawing Photoelectric proximity switch Robust Teflon housing for use in wet and aggressive environments Suitable for food applications ø. ø 7.7. 7 7.8 Scanning distance set via teach-in wire Background suppression ø..8 Adjustments possible LED signal ounting hole Ø. mm Cable m, Ø. mm, m Teflon coated, Ø. mm Optical axis, receiver Standard direction of the material being scanned Optical axis, sender WTBT-N WTBT-P See Accessories chapter ounting systems x 0. mm² ET SICK 008-0-0
W- WTBT- N P Scanning distance typ. max. Operating distance... 0 mm... 0 mm Adjustment of operating distance Teach-in: External ) Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 7 mm at 0 mm distance Supply voltage V s DC 0... 0 V ) Ripple < Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, Light-switching 00 ma Response time < ms ) < 0. ms ) Switching frequency 00 Hz 7),000 Hz 7) Cable, PVC/Teflon coating, m 8) VDE protection class Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP 8, IP 9K Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material PTFE/Teflon ) External teach-in: impuls > s with voltage V s for PNP or for NPN ) Average service life 00,000 h at Ta = + C ) Limit values ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load 7) With light/dark ratio : 8) Do not bend below 0 C Ordering information WTBT-N 0809 WTBT-P 0809 008-0-0 SICK
Photoelectric reflex switch, WLS-, autocollimation, light- and dark-switching Scanning range 0... m Photoelectric reflex switch Dimensional drawing. 7. Reliable function in restricted spaces thanks to autocollimation Small, easily visible, tightly defined light spot Robust mounting thanks to metal bushes 8. 9.8 8.8 Adjustments possible Optical axis ounting hole Connector LED signal strength indicator green: power on LED signal strength indicator orange: status of received light beam WLS-E0 WLS-F0 WLS-P0 WLS-P0 WLS-F0 WLS-P0 WLS-E0 WLS-N0 WLS-P0 See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems Reflectors 8, -pin 8, -pin 8, -pin x 0. mm² SICK 008-0-0
W- WLS- E0 E0 F0 F0 N0 P0 P0 P0 P0 Scanning range typ. max. Scanning range, recommended Relating to 0... m 0.... m Reflector PL80A Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter Polarisation filter mm at. m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, PNP antivalent Dark-switching Light-switching Complementary 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Cable, PVC, m 7) Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 7) Connector, 8, -pin Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Scanning range and operating reserve 0 0 0 0 0 0 0. 0.8.0. 0 (m) Operating range Reflector type PL80A PL0F PL0A PL0F PL0F REF-IRF-..8.0.0..7.0,0,0,0,0 Scanning range max. typical Operating range 0.... m 0....0 m 0....8 m 0.... m 0....0 m 0... 0. m.0 Function reserve 00 0 Scanning range max. typ. [mm] 000 000 000 000 Distance Operating range Ordering information WLS-E0 007 WLS-E0 007 WLS-F0 00 WLS-F0 007 WLS-N0 007 WLS-P0 008 WLS-P0 009 WLS-P0 00 WLS-P0 0070 008-0-0 SICK
Photoelectric reflex switch, WLS-, teach-in, autocollimation, light- and dark-switching Scanning range 0... m Photoelectric reflex switch Dimensional drawing. 7. Reliable function in restricted spaces thanks to autocollimation Small, easily visible, tightly defined light spot uick and easy commissioning through teach-in function Robust mounting thanks to metal bushes 8. 9.8 8.8 Adjustments possible Optical axis ounting hole Connector LED signal strength indicator green: power on LED signal strength indicator orange: status of received light beam Teach button WLS-E WLS-F WLS-N WLS-V WLS-E WLS-F WLS-P WLS-F x 0. mm² 8, -pin 8, -pin 8, -pin See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems Reflectors WLS-W x 0. mm² WLS-P 8, -pin Alarm Alarm SICK 008-0-0
W- WLS- E E F F F N P P V W Scanning range typ. max. Scanning range, recommended Relating to 0... m 0... m Reflector PL80A Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter Polarisation filter mm at. m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, PNP antivalent PNP, and alarm NPN, and alarm Dark-switching Light-switching Complementary 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Alarm output Pre-failure signalling output Cable, PVC, m 7) Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm 7) Connector, 8, -pin Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Teach-in function Programming via teach-in button. Easy programming: Position reflector in the beam path, press button, ready: LED confirms teach-in operation. Double reseve via switching threshold. Scanning range and operating reserve... 0. 0.8.0. 0 (m) Operating range Reflector type PL80A PL0A PL0A PL0F REF-IRF-.0.0.0.0.0.0 Operating range 0....0 m 0....0 m 0.... m 0.... m 0... 0. m.0 Scanning range, max. typical.0 Function reserve 00 0 Operating range Scanning range max. typical [mm] 000 000 000 000 000 Ordering information WLS-E 008 WLS-E 0080 WLS-F 007 WLS-F 007 WLS-F 007 WLS-N 008 WLS-P 0077 WLS-P 0078 WLS-V 0079 WLS-W 008 008-0-0 Distance SICK 7
Photoelectric reflex switch, WLGS-, for transparent objects Scanning range 0... m Photoelectric reflex switch Continuous adaptation of the switching threshold in case of lens contamination Stable operation thanks to temperature compensation Small, easily visible, tightly defined light spot uick and easy commissioning through teach-in function Detection of glass objects with an attenuation of > 8% Dimensional drawing. 8. A 9.8 7. 8.8 Adjustments possible A Optical axis ounting hole Connector LED signal strength indicator green: power on LED signal strength indicator orange: status of received light beam Teach button 7 WLGS-F WLGS-E WLGS-W WLGS-V 8, -pin x 0, mm² x 0, mm² 8, -pin ET Alarm Alarm WLGS-P WLGS-F WLGS-P WLGS-F See Accessories chapter Connector, 8, -pin ounting systems Reflectors 8, -pin 8, -pin 8, -pin ET 8 SICK 008-0-0
W- WLGS- E F V W P P F F Detection of transparent objects Attenuation along light beam > 8 % Scanning range typ. max. Scanning range, recommended Relating to Sensitivity adjustment 0... m 0... m Reflector PL80A Teach-in: single-teach button Teach-in: single-teach button & cable Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter Polarisation filter mm at. m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, Dark-switching 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Alarm output Pre-failure signalling output Cable, PVC, m 7) Connector, 8, -pin, Cable with plug, 8, -pin, 00 mm 7) Cable with plug, 8, -pin, 00 mm 7) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Teach-in function Programming via teach-in button Standard mode (switching threshold adaptation): sensor adjusts the switching threshold to the ambient conditions. Sensor has clear sight of the reflector. No object in the beam path: press teach-in button for > s until yellow LED indicator lights up again. Sensor is ready to operate. Switch off switching threshold adaptation: sensor works statically with a switching threshold of 0 %. Sensor has clear sight of the reflector. No object in the beam path: press teach-in button for > 8s until yellow LED indicator flashes twice. Sensor is ready to operate. Scanning range and operating reserve... 0. 0.8.0. 0 (m) Operating range Reflector type PL80A PL0A PL0A PL0F REF-IRF-.0.0.0.0.0.0 Operating range 0....0 m 0....0 m 0.... m 0.... m 0... 0. m.0 Scanning range, max. typical.0 Function reserve 00 0 Operating range Scanning range max. typical [mm] 000 000 000 000 000 Order information WLGS-E 008 WLGS-F 008 WLGS-V 0087 WLGS-W 008 WLGS-P 08 WLGS-P 089 WLGS-F 088 WLGS-F 080 008-0-0 Distance SICK 9
Photoelectric reflex switch, WL-, red light, light- and dark-switching Scanning range 0.0... m Photoelectric reflex switch Dimensional drawing Fast and safe alignment through high visibility light spot Fast commissioning. Connect, align, ready! Easy assembly in slots and guide rails 9. 8... 9 Adjustments possible Centre of optical axis, sender Centre of optical axis, receiver LED signal strength indicator yellow: status of received light beam LED signal strength indicator green: power on ounting hole Connector WL-F0 WL-N0 WL-P0 WL-E0 WL-F0 WL-P0 WL-P0 WL-E0 WL-F0 WL-P0 See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems Reflectors 8, -pin 8, -pin 8, -pin x 0. mm² 0 SICK 008-0-0
W- WL- E0 E0 F0 F0 F0 N0 P0 P0 P0 P0 Scanning range typ. max. Scanning range, recommended Relating to 0.0... m 0.0.... m Reflector PL80A Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter Polarisation filter 7 mm at. m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, PNP antivalent Dark-switching Light-switching 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Cable, PVC, m 7) Connector, 8, -pin Cable with plug, 8, -pin, 00 mm 7) Connector, 8, -pin Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Scanning range and operating reserve 0.09 0. 0.9 0.0 0.8. 0.0.. 0.0.7 0.0.. 0 (m) 0..... Reflector type Operating range REF-IRF- 0.09... 0. m PL0F PL0A PL0A PL80A 0.0... 0.8 m 0.0.... m 0.0....7 m 0.0.... m 00 Operating reserve 0 Operating range Scanning range max. typical [m] 0..0..0..0..0. Distance Ordering information WL-E0 08 WL-E0 088 WL-F0 08 WL-F0 08 WL-F0 08 WL-N0 080 WL-P0 08 WL-P0 08 WL-P0 087 WL-P0 08 008-0-0 SICK
Photoelectric reflex switch, WLG-, for transparent objects, with polarisation filter Scanning range 0.0... m Photoelectric reflex switch Dimensional drawing Fast and safe alignment through high visibility light spot Detection of glass objects with an attenuation of > 8% Sensitivity setting via wire 9. 8... 9 7 Adjustments possible Centre of optical axis, sender Centre of optical axis, receiver LED signal strength indicator orange: status of received LED signal strength indicator green: power on ounting hole Connector 7 Teach button 7 WLG-E WLG-E WLG-F WLG-P WLG-F WLG-E WLG-P x 0, mm² 8, -pin 8, -pin x 0, mm² ET ET See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems WLG-F WLG-F 8, -pin 8, -pin ET SICK 008-0-0
W- WLG- E E E F F F F P P Detection of transparent objects Attenuation along light beam > 8 % Scanning range typ. max. Scanning range, recommended Relating to Sensitivity adjustment 0.0... m 0.0.... m Reflector PL80A Teach-in: single-teach button & cable Teach-in: single-teach button Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter Polarisation filter 7 mm at. m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, Dark-switching Light-switching 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Cable, PVC, m 7) Connector, 8, -pin Connector, 8, -pin Cable with plug, 8, -pin, 00 mm 7) Cable with plug, 8, -pin, 00 mm 7) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Teach-in-Funktion Programming via teach-in button. Easy programming: Position reflector in the beam path, press button, ready: LED confirms teach-in operation. Two operating modes: Standard setting: short Teach-in period (< 8 s); for standard applications; approx. double reserve via switching threshold Fine adjustment: long Teach-in period (> 8 s); for precise applications, transparent objects. Small switching hysteresis. Scanning range and operating reserve 0.09 0. 0.9 0.0 0.8. 0.0.. 0.0.7 0.0.. 0 (m) 0..... Reflector type Operating range REF-IRF- 0.09... 0. m PL0F PL0A PL0A PL80A 0.0... 0.8 m 0.0.... m 0.0....7 m 0.0.... m 00 Operating reserve 0 Operating range Scanning range max. typical Ordering information WLG-E 08 WLG-E 08 WLG-E 08 WLG-F 087 WLG-F 080 WLG-F 088 WLG-F 089 WLG-P 08 WLG-P 097 [m] 0..0..0..0..0. 008-0-0 SICK Distance
Photoelectric reflex switch, WLG-, for transparent objects, without polarisation Scanning range 0.0.... m Photoelectric reflex switch Dimensional drawing Fast and safe alignment through high visibility light spot Detection of PET bottles and foils with an attenuation of > 8% Sensitivity setting via wire 9. 8... 9 7 Adjustments possible Centre of optical axis, sender Centre of optical axis, receiver LED signal strength indicator orange: status of received light beam LED signal strength indicator green: power on ounting hole Connector 7 Teach button 7 WLG-E8 WLG-P8 WLG-F8 WLG-P8 WLG-F8 WLG-E8 WLG-N8 x 0, mm² 8, -pin 8, -pin x 0, mm² ET ET See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems WLG-F8 8, -pin SICK 008-0-0
W- WLG- E8 E8 F8 F8 F8 N8 P8 P8 Detection of transparent objects Attenuation along light beam > 8 % Scanning range typ. max. Scanning range, recommended Relating to Sensitivity adjustment 0.0.... m 0.0... 0.9 m Reflector PL80A Teach-in: single-teach button & cable Teach-in: single-teach button Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 80 mm at. m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption 0 ma ) Switching outputs Switching mode Output current I a max NPN, PNP, Dark-switching 00 ma Response time < 0. ms ) Switching frequency,000 Hz ) Cable, PVC, m 7) Cable, PVC, m 7) Connector, 8, -pin Connector, 8, -pin Cable with plug, 8, -pin, 00 mm Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +7 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Without load ) Signal transit time with resistive load ) With light/dark ratio : 7) Do not bend below 0 C Teach-in function Programming via teach-in button. Easy programming: Position reflector in the beam path, press button, ready: LED confirms teach-in operation. Two operating modes: Standard setting: short Teach-in period (< 8 s); for standard applications; approx. double reserve via switching threshold Fine adjustment: long Teach-in period (> 8 s); for precise applications, transparent objects. Small switching hysteresis. Scanning range and operating reserve 0.0 0. 0. 0.0 0. 0. 0.0 0. 0.9 0.0 0.9. 0 (m) 0. 0. 0. 0.8.0... Reflector type Operating range PL0F 0.0... 0. m PL0A PL0A PL80A 0.0... 0. m 0.0... 0. m 0.0... 0.9 m 00 0 Function reserve [m] Operating range Scanning range typ. max WLG- 0. 0. 0. 0.8.0... Ordering information WLG-E8 080 WLG-E8 088 WLG-F8 08 WLG-F8 087 WLG-F8 08 WLG-N8 009 WLG-P8 09897 WLG-P8 079 008-0-0 SICK
Through-beam photoelectric switch, WSES-, red light, light- and dark-switching Scanning range 0... m Through-beam photoelectric Dimensional drawing. 7. Fast and reliable alignment through brilliant light spot Assembly of several pairs in tight environments due to a tightly defined small light spot Robust mounting thanks to metal bushes 8. 9.8 8.8 Adjustments possible Centre of optical axis LED signal strength indicator orange: status of received light beam LED signal strength indicator green: power on ounting hole Connector WSES-E0 WSES-F0 WSES-P0 WSES-F0 WSES-E0 WSES-F0 WSES-N0 Sender 8, -pin 8, -pin x 0. mm² See Accessories chapter Connector, 8, -pin ounting systems TE TE TE Receiver 8, -pin 8, -pin x 0. mm² SICK 008-0-0
W- WSES- E0 E0 F0 F0 F0 N0 P0 Scanning range typ. max. Scanning range, recommended 0... m 0.... m Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 0 mm at.0 m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption, sender Power consumption, receiver Switching outputs Switching mode Output current I a max 0 ma 0 ma NPN, PNP, Dark-switching Light-switching 00 ma Response time. ms ) Switching frequency 00 Hz ) Test input sender off TE to 0 V Cable, PVC, m ) Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm ) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +70 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Signal transit time with resistive load ) With light/dark ratio : ) Do not bend below 0 C Scanning range and operating reserve 0. 0 (m) Operating range Scanning range typ. max 000 00 WSES- Ordering information WSES-E0 009 WSES-E0 009 WSES-F0 0090 WSES-F0 0088 WSES-F0 0089 WSES-N0 009 WSES-P0 009 Operating reserve Operating range [m] Distance 008-0-0 SICK 7
Through-beam photoelectric switch, WSE-, red light, light- and dark-switching Scanning range 0... m Through-beam photoelectric Dimensional drawing Fast and safe alignment through high visibility light spot Fast commissioning. Connect, align, ready! Easy assembly in slots and guide rails 9. 8. 7. 9 Adjustments possible Centre of optical axis LED signal strength indicator orange: status of received light beam LED signal strength indicator green: power on ounting hole Connector WSE-F0 WSE-P0 WSE-P WSE-F0 WSE-F WSE-P0 WSE-P0 WSE-E0 WSE-F0 WSE-N0 Sender 8, -pin 8, -pin 8, -pin x 0. mm² TE TE NC TE TE See Accessories chapter Connector, 8, -pin Connector, 8, -pin ounting systems Receiver 8, -pin 8, -pin 8, -pin x 0. mm² 8 SICK 008-0-0
W- WSE- E0 F0 F0 F F0 N0 P0 P0 P0 P Scanning range typ. max. Scanning range, recommended Sensitivity adjustment 0... m 0.... m Potentiometer, revolutions Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 0 mm at m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption, sender Power consumption, receiver Switching outputs Switching mode Output current I a max 0 ma 0 ma NPN, PNP, PNP Dark-switching Light-switching Complementary 00 ma Response time > 0. ms ) Switching frequency,000 Hz ) Test input sender off TE to 0 V Cable, m ) Connector, 8, -pin Cable with plug, 8, -pin, PVC, 00 mm ) Connector, 8, -pin ) Connector, 8, -pin Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP, IP 7 Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +70 C Weight Ca. 0 g Housing material Bayblend, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Signal transit time with resistive load ) With light/dark ratio : ) Do not bend below 0 C Scanning range and operating reserve 000 WSE- 0. 0 (m) 00 Operating range Scanning range typ. max. Operating reserve 0 [m] Distance Ordering information WSE-E0 087 WSE-F0 088 WSE-F0 087 WSE-F 0 WSE-F0 0870 WSE-N0 08 WSE-P0 08 WSE-P0 080 WSE-P0 08 WSE-P 09898 008-0-0 SICK 9
Through-beam photoelectric switch, WSE-, red light, in Teflon housing Scanning range 0... m Dimensional drawing Through-beam photoelectric Robust Teflon housing for use in ø. ø 7.7 7.8 wet and aggressive environments Suitable for food applications. 7 Test input ø..8 Adjustments possible LED signal ounting hole Ø. mm Cable m, Ø. mm, m Teflon coated, Ø. mm Optical axis, sender und receiver WSET-E0 WSET-F0 WSET-P0 Sender x 0. mm² TE See Accessories chapter ounting systems Receiver x 0. mm² 0 SICK 008-0-0
W- WSET- E0 F0 P0 Scanning range typ. max. Scanning range, recommended 0... m 0.... m Light source, light type Pinpoint LED, red light, 0 nm ) Light spot diameter 0 mm at m distance Supply voltage V s DC 0... 0 V ) Ripple Vss ) Power consumption, sender Power consumption, receiver Switching outputs Switching mode Output current I a max 0 ma 0 ma NPN, PNP, Dark-switching Light-switching 00 ma Response time > 0. ms ) Switching frequency,000 Hz ) Test input sender off TE to 0 V Cable, m ) Circuit protection V s connections reverse-polarity protected / Output and not short-circuit protected / Interference suppression Enclosure rating IP 8, IP 9K Ambient temperature operation 0 C... +0 C Ambient temperature storage 0 C... +70 C Weight Ca. 0 g Housing material PTFE/teflon, PA ) Average service life 00,000 h at Ta = + C ) Limit values, reverse-polarity protected operation in short-circuit protected network max. 8 A ) ay not exceed or fall short of V s tolerances ) Signal transit time with resistive load ) With light/dark ratio : ) Do not bend below 0 C Scanning range and operating reserve 0. 0 (m) Operating range Scanning range, max. typical 00 0 Ordering information WSET-E0 098 WSET-F0 097 WSET-P0 09 Operating reserve Operating range Scanning range, max. typ. (m) 008-0-0 SICK