John ewis aine white/ash bed king size Stock number: 80307103 Thank you for purchasing this aine bedstead. lease read the instructions carefully before use to ensure safe and satisfactory operation of this product re-assembly preparation lease ensure instructions are read in full before attempting to assemble this product ecessary Tools You will require a cross head screwdriver to assemble this product. An electric drill may cause damage to the product and is not recommended. lease check the pack contents before attempting to assemble this product. A full checklist of components is given in this leaflet. If any components are missing, please contact John ewis customer services or your local branch. This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE ARE WHE ITI to avoid personal injury and (or) damage to the product. This product takes approximately 60 IUTES to assemble with /2 EOE. The fittings pack contains SA ITES which should be KET AWAY RO YOU HIRE. Read this leaflet in full before commencing assembly. 1 of 9
and parts checklist A E B A Headboard x 1 B ootboard x 1 Side supports x 2 Side support list x 4 E entre support beam x 1 Slats x 32 8 x85mm Bolt x 8 H Half moon x 8 I ut x 8 J 8x30mm wooden dowel x 8 K Spanner x 1 10x40mm wooden dowel x 8 2 of 9
4x35mm screw x 20 4x25mm screw x 4 O lastic midd caps x 16 lastic end caps x 32 3 of 9
Step by step assembly instructions Step One Insert four dowels () into the holes provided in the side support () Repeat for both side supports using a total of eight dowels () X 8 Step Two ix bolt () into the bushing on headboard (A) as shown. A X 4 60mm 4 of 9
Step Three ix bolt () into the bushing on footboard (B) as shown. 60mm X 4 B Step our Insert two dowels (J) in the side support list () Repeat for all four side support list J X 8 J x 4 J 5 of 9
Step ive To attach the side supports to the headboard, you firstly place the halfmoon (H) on the bolt (), and then you place the nut (I) on the bolt and screw it on. Use spanner (K) to tighten the nut (I) Be careful not to over tighten H I A K H X 4 I X 4 K X 1 Step Six To attach the side supports to the footboard, you firstly place the halfmoon (H) on the bolt (), and then you place the nut (I) on the bolt and screw it on. Use spanner (K) to tighten the nut (I) Be careful not to over tighten H X 4 H I K I X 4 B K X 1 6 of 9
Step Seven Insert the end of the central support beam (E) into the U-itting placed on headboard (A) and footboard (B) and use screw () to fasten it. X 4 E Step Eight ix the side support list () to the side supports () and fasten using the 35mm screws () X 20 7 of 9
Step ine lace the plastic midd caps (O) and the plastic end caps ()onto the slats () as shown O O X 16 X 32 O Step Ten O 8 of 9
are and aintenance This aine bed should be cleaned using a soft damp cloth and dried immediately. o not use a very wet cloth or allow any liquid to contact with the veneers for a long period of time as this can permanently damage the surface. o not use any abrasive cleaner or harsh detergent as this can damage the surface of the veneers. Safety Instructions eneral warnings: ever drag furniture when moving it, always lift it. eriodically check all fixings to ensure none have come loose and re-tighten when necessary. lease take care when handling or moving the furniture as careless handling may cause damage or injury. urniture can be dangerous if incorectly installed. Assembly should be carried out by a competent person. o iability will be accepted for damage or injury caused by incorrectly. Specific warnings for heavy items: It is recommended that before moving heavy objects to a new location they are completely disassembled to avoid personal injury or damage to the furniture. lease be careful to retain all fittings when doing this. EASE KEE THESE ISTRUTIOS OR UTURE REEREE John ewis artnership 171 Victoria Street ondon SW1E 5 www.johnlewis.com 9 of 9