Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level T-30 Torx Drive Bit If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500) Or visit our website: www.steelcase.com 2015 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Printed in U.S.A. #2 Phillips Drive Bit Page 1 of 21
TABLE OF CONTENTS: PAGE(S): Installing the Inline Connector... Assembling & Attaching the End Panel... Assembling & Attaching the Utility Pole to the Bench... Assembling & Attaching the Utility Pole to the Ceiling... 3 4-7 8-9 10-13 STOP - Electrical Inspection Required before moving on! Attaching the Data Tray End Cover - Utility Pole with Open Leg Covers... Attaching the Data Tray End Cover - Utility Pole with Closed Leg Covers... Attaching the Various Extension Trays... Attaching the Data Tray End Cover - End Panel with Open Leg Covers... Attaching Lifting Column Covers... Leveling the Assembly... 14 15 16 17 18-20 21 Hardware Description M8x1.25x70mm Metric Flat Head Screw 5mm Hex Drive (Silver) 16133112 M6x1.00x13mm Metric Button Head Screw T30 Torx Drive (Silver) 442F0004 #10-12 x 5/8 Truss Head Screw #2 Quadrex Square Drive (Black) 855010126 1/4-20 x 3/4 Button Head Screw #2 Phillips Drive (Silver) 853071664 #8-18 x 1/4 Truss Head Screw #2 Quadrex Square Drive (Black) 854008757 Page 2 of 21
Installing the Inline Connector Use the inline connector when attaching: - End Panel - Utility Pole - End Panel with Utility Pole 1 Insert the pre-assembled connector into the end of the beam and secure using the fasteners (included). 1 M8x1.25x70MM METRIC FLAT HEAD SCREW 5MM HEX DRIVE NOTE: For Utility Pole Installations: Attach Utility Pole L bracket now, prior to attaching an End Panel. M6x1.00x13MM METRIC BUTTON HEAD SCREW T30 TORX DRIVE Page 3 of 21
Assembling & Attaching the End Panel 1 a) Attach (5) brackets to Infill Panel as shown. b) DO NOT fully tighten screws. NOTE: Post Leg shown. Loop Leg assembly is the same. 2 Attach left and right End Panel Brackets 1a #10-12 x 5/8 TRUSS HEAD SCREW WITH #2 QUADREX SQUARE DRIVE 2 1b #10-12 x 5/8 TRUSS HEAD SCREW WITH #2 QUADREX SQUARE DRIVE Screws will be fully tightened later. Page 4 of 21
Assembling & Attaching the End Panel (cont.) 3 4 5 6 Position infill onto leg. Rotate mounting brackets onto leg, align with holes and install screws. Install top screw first, then the screws in the sides. Fully tighten all screws. Snap on plastic covers. 4 BOTTOM VIEW showing Infill Panel attached to legs. 3 6 Page 5 of 21
Assembling & Attaching the End Panel (cont.) 7 Install End Panel to Bench with (4) screws, as shown. M6x1.00x13MM METRIC BUTTON HEAD SCREW T30 TORX DRIVE 7 Page 6 of 21
Assembling & Attaching the End Panel (cont.) 8 Install bracket caps, as shown. NOTE: Bracket caps installation can be delayed until bench assembly is complete. 8 INFILL NOT SHOWN FOR CLARITY NOTE: If your configuration is End Panel Only (no Utility Pole), skip to page 17. Page 7 of 21
Assembling & Attaching the Utility Pole (see pages 4-7 for Assembling & Attaching the End Panel) Refer to page 10 for information on removing ceiling tile. 1 Install square aluminum block onto utility pole with 1/4-20 x 3/4 button head screws as shown. 1/4-20 x 3/4 BUTTON HEAD SCREW #2 PHILLIPS DRIVE 3 Attach bracket to rail and secure with M6x1.00x13mm button head screws provided. 1 Drive bolts through inside of power pole. BLOCK UTILITY POLE 3 M6x1.00x13MM METRIC BUTTON HEAD SCREW T30 TORX DRIVE BRACKET 2 a) Thread glide into pole base, then b) snap base into bottom of utility pole. BASE 2a 2b Page 8 of 21
Assembling & Attaching the Utility Pole (cont.) 4 5 Position pole assembly so that block extends into rail extrusion. Attach pole to bracket with (2) 1/4-20 x 3/4 button head screws provided. NOTE: Before routing power cords, attach utility pole to ceiling. See page 10. 4 5 Page 9 of 21
Install Utility Pole into a Ceiling 1 Remove the ceiling tile where the utility pole will be placed. 3 Assemble ceiling trim plate. 3 1 4 Bend retainers up and insert ceiling trim plate into the ceiling tile cut-out. 2 Cut ceiling tile hole. 3-1/4" x 6-1/4" 3-1/8" 4 2 1-5/8" Page 10 of 21
Install Utility Pole into a Ceiling (cont.) 5 Place ceiling tile with trim plate back in ceiling. 7 Insert the vertical channel through the ceiling tile hole. NOTE: If the vertical channel extends above the ceiling tile more than 4 inches mark and cut excess material off before securing to the frame or junction bracket. 5 4" max 7 6 Remove adjacent ceiling tile. 6 8 Route any power cords, harness and data cables as needed. Page 11 of 21
Install Utility Pole into a Ceiling (cont.) 9 10 Attach the ceiling bracket to the top of the vertical channel. Secure crossbar to the ceiling grid. #8-18x 3/8" 9 12 10 #8-18 x 1/4" 11 11 Attach slotted adjustment bracket to the cross bar and fully tighten screw. #8-18 x 1/4" 12 Attach slotted adjustment bracket to the ceiling bracket. Be sure not to fully tighten the screws. Gold #8-18 x.360" Page 12 of 21
Install Utility Pole into a Ceiling (cont.) 13 Secure junction box to ceiling bracket and complete cabling. MODULAR HARDWIRE 14 15 Snap the cover in place along the length of the vertical channel. Tighten screws connecting the slotted adjustment bracket to the ceiling bracket as shown on step 12. TO BUILDING TO BEAM 13 #8-18 x 1/4" 14 #8-18 x 3/8" Pan Head STOP: BEFORE PROCEEDING, ALL POWER AND DATA SHOULD BE INSTALLED. HAVE ALL NECESSARY INSPECTIONS BEEN COMPLETED? Page 13 of 21
Attaching the Data Tray End Cover - Only for Utility Pole with Open Covers Configuration 1a UTILITY POLE NOT SHOWN FOR CLARITY ENSURE BOTH OUTSIDE FLANGES OF COVER ARE TUCKED INSIDE OUTER TRAY AS SHOWN 1d 1c #8-18 x 1/4 TRUSS HEAD SCREW #2 QUADREX SQUARE DRIVE 1e 1b Page 14 of 21
Attaching the Data Tray End Cover - Only for Utility Pole with Closed Covers Configuration 1a UTILITY POLE NOT SHOWN FOR CLARITY 1b #8-18 x 1/4 TRUSS HEAD SCREW #2 QUADREX SQUARE DRIVE #8-18 x 1/4 TRUSS HEAD SCREW #2 QUADREX SQUARE DRIVE Page 15 of 21
Attaching the Various Extension Trays 1 Install extension tray to utility pole with (4) 1/4-20 x 3/4 button head screws provided. Extension Tray used with: Utility Pole Only (Open Covers) NOTE: See page 14. This tray requires the Data Tray End Cover to be installed FIRST. Extension Tray used with: Utility Pole Only (Closed Covers) 1/4-20 x 3/4 BUTTON HEAD SCREW #2 PHILLIPS DRIVE Extension Tray used with: Utility Pole with End Panel Page 16 of 21
Attaching the Data Tray End Cover - Only for Configurations with an End Panel 1a END PANEL NOT SHOWN FOR CLARITY 1c #8-18 x 1/4 TRUSS HEAD SCREW #2 QUADREX SQUARE DRIVE 1b Page 17 of 21
Attaching Lifting Column Covers 1 Remove the backing film (release liner) from the dual lock tape. 2 Align the interior cover holes with the holes in the lifting column connector (2a) and attach using screws provided (2b). OPEN COVER END PANEL/UTILITY POLE INTERIOR & EXTERIOR 2b M6x1.00x13MM METRIC BUTTON HEAD SCREW T30 TORX DRIVE 2a CLOSED COVER UTILITY POLE ONLY INTERIOR OPEN COVER END PANEL/UTILITY POLE INTERIOR & EXTERIOR OPEN COVER UTILITY POLE ONLY EXTERIOR CLOSED COVER UTILITY POLE ONLY INTERIOR CLOSED COVER UTILITY POLE ONLY EXTERIOR 1 Page 18 of 21
Attaching Lifting Column Covers (cont.) M6x1.00x13MM METRIC BUTTON HEAD SCREW T30 TORX DRIVE 3 Align the interior end cover holes with the holes in the lifting column connector (3a) and attach using screws provided (3b). Make sure to connect both sides together as shown (3c) for the full interior end covers. 3b 3a 3c Page 19 of 21
Attaching Lifting Column Covers (cont.) 4 Press down at the locations shown to bond the dual lock tape to the lifting columns. 5 Align the flat edges of the Top Covers with the center beam, and press down to bond the dual lock tape. 5 5 4 ATTACH EXTERIOR COVERS IN THE SAME MANNER AS THE INTERIOR COVERS Page 20 of 21
Leveling the Assembly 1 Before use, the table must be completely leveled, front-to-back and side-to-side using the height adjustable glides. Failure to do this could cause the lifting columns to bind. 2 After the table has been leveled, adjust the End Panel and/or Utility Pole glides. 2 2X GLIDE 1 4X 2 Page 21 of 21