c c e s s H a r d w a r e
PM BRND SS HRDWR PM brand access hardware is designed with captive screws to help keep parts to a minimum and eliminate risks associated with loose hardware that could fall out and damage internal components. These panel fastener assemblies are ideal to attach metal panels or other thin material components in applications where subsequent access will be necessary. PM threaded access hardware types include selfclinching panel fasteners with low-profile design that hugs front panels and a large knurl for ease of use; self-clinching panel fasteners with universal slot/phillips recess; tool or hand actuated self-clinching panel fasteners in steel or stainless steel to resist corrosion; stainless steel panel fasteners that meet UL 195 service access area requirements; low-cost self-clinching panel fasteners featuring a small, compact, and low-profile design for limited access areas; flush-mounted panel screw components; snap-in panel fasteners designed to be installed without tools; press-in panel fasteners allowing for radial float to compensate for mating hole misalignment; and surface mount panel fasteners. For special applications or designs, please consult your local engineering representative or a factory engineer. TYP PF11 TM ND PF12 TM Self-clinching with tool or finger operation............. Page 4 TYP PF13 TM ND PF14 TM Self-clinching with tool or finger operation............. Page 5 TYP PF11M, PF12M, PF13M, PF14M nti cross-threading technology.................... Page 6 TYP PFHV TM ompact, self-clinching with tool or finger operation....... Page 7 TYP PF2 ND PFS2 Self-clinching with tool or finger operation............. Page 8 TYP PF4 Self-clinching in stainless with tool or finger operation..... Page 9 TYP PF3 Low-profile, self-clinching with tool or finger operation.... Page 1 TYP PF5 TM ND PF6 TM Low-profile, self-clinching with tool or finger operation.... Page 11 TYP PF1 Flush-mounted, self-clinching with tool only operation..... Page 12 TYP PF2P TM Self-clinching with tool only operation................ Page 15 TYP PFF TM HYBRID TM, floating with tool or finger operation.......... Page 16 TYP PFP TM HYBRID TM, self-clinching with tool or finger operation...... Page 17 TYP PFT TM HYBRID TM thumbscrews.......................... Page 18 TYP PFK Broaching for P.. boards, with tool or finger operation.... Page 19 TYP PTL2 Self-clinching spring-loaded plunger assemblies......... Page 19 ReelFast PNL FSTNRS (PF) Surfaced mounted on P.. boards................... Page 2 Material & Finish Specifications................... Page 22 Installation.................................. Page 24 Performance Data.............................. Page 3 HIHT OMPRISON UID ND STNDRD RSS FOR SM THRD SIZ PNL FSTNRS PF1 PFHV PF3/31/32 PF5/6 PF2/PFS2 PFK PF2P Installed height above sheet. PF-2 opyright 1998 Pennngineering.
PM PNL FSTNR SLTOR UID PM Panel Fastener p p l i c a t i o n R e q u i r e s : PF11/PF11M PF12/PF12M PF13/PF13M PF14/PF14M PF2 PF4 PFS2 PFHV PF3 PF31 PF32 Meets Meets Recesses Stainless Installs Spring Tool Hand Installs Installs Multiple Flush vailable vailable UL 58 UL 195 steel for into loaded actuated actuated into any Into screw mounted in black in operator service Slot/ Phillips Slot Six-lobe/ corrosion stainless assembly thin printed lengths custom access access Phillips slot resistance steel material circuit colors area area available sheet boards (2) req. req. PF5 PF6 PF1 PF2P PFF (1) PFP (1) PFT (1) PFK ReelFast PF (1) (1) Standard color is black. (2) See page PF-32 for custom color capabilities. PF4 PFP PFF PF11/PF12 PF11M/PF12M PF13/PF14 PF13M/PF14M ReelFast PF PF-3
TYP PF11 TM ND PF12 TM SLF-LINHIN PNL FSTNR SSMBLIS Shoulder provides positive stop during installation. Universal (slot/phillips) recess. PF11 meets UL 58 operator access area requirements. PF12 meets UL 195 service access area requirements. vailable with durable black finish. vailable in three screw lengths. Four dimples on head designate metric thread. Driver size. PF11-832 - BL Finish Shoulder provides positive stop during installation. T 2 T 1 PF11 Patented. SRTH PROOF P Min. Float -.2 /.51 mm total. PF12 DuraBlack TM finish ll dimensions are in inches. Size Knurled Smooth ap ap.112-4 (#4-4).138-32 (#6-32).164-32 (#8-32).19-32 (#1-32).25-2 (1/4-2) (Shank) Max. Min. Sheet Thickness Hole Size In Sheet P T 1 T 2 Driver Hole +.3 Max. ±.1 ±.25 ±.25 Nom. Nom. Size /L To -. dge.17. PF11 PF12 44 1.36.36.219.218.417.23.6.31.45 #1.28 2.29.12.23. PF11 PF12 632 1.36.36.25.249.45.29.6.45.64 #2.29 2.35.12.23. PF11 PF12 832 1.36.36.312.311.514.29.6.45.64 #2.33 2.35.12.23. PF11 PF12 32 1.36.36.312.311.514.29.6.45.64 #2.33 2.35.12.29. PF11 PF12 42 1.36.36.375.374.575.35.6.53.79 #3.46 2.41.12 ll dimensions are in millimeters. Size x Pitch Knurled Smooth ap ap Min. Hole Size (Shank) Sheet In Sheet Max. Thickness +.8 P T 1 T 2 Driver Hole Max. ±.25 ±.64 ±.64 Nom. Nom. Size /L To dge 4.32 M3 x.5 PF11 PF12 M3 1.92.92 5.56 5.54 1.59 5.84 1.52 7.87 11.43 #1 7.11 2 7.37 3.5 5.84 M3.5 x.6 PF11 PF12 M3.5 1.92.92 6.35 6.33 11.43 7.37 1.52 11.43 16.26 #2 7.37 2 8.89 3.5 5.84 M4 x.7 PF11 PF12 M4 1.92.92 7.92 7.9 13.6 7.37 1.52 11.43 16.26 #2 8.38 2 8.89 3.5 5.84 M5 x.8 PF11 PF12 M5 1.92.92 7.92 7.9 13.6 7.37 1.52 11.43 16.26 #2 8.38 2 8.89 3.5 7.37 M6 x 1 PF11 PF12 M6 1.92.92 9.53 9.5 14.61 8.89 1.52 13.46 2.7 #3 11.68 2 1.41 3.5 PF-4
TYP PF13 TM ND PF14 TM SLF-LINHIN PNL FSTNR SSMBLIS Universal slot/phillips recess. PF13 meets UL 58 operator access area requirements. PF14 meets UL 195 service access area requirements. vailable with durable black finish. vailable in three screw lengths. Four dimples on head designate metric thread. Driver size. PF13-632 - BL Finish T 2 T1 SRTH PROOF P PF13 PF14 DuraBlack TM finish Min. Float -.2 /.51 mm total. ll dimensions are in inches. Size Knurled Smooth ap ap.112-4 (#4-4).138-32 (#6-32).164-32 (#8-32).19-32 (#1-32).25-2 (1/4-2) (Shank) Max. Min. Sheet Thickness Hole Size In Sheet P T 1 T 2 Driver Hole +.3 Max. ±.1 ±.25 ±.25 Nom. Nom. Size /L To -. dge.17. PF13 PF14 44 1.36.36.219.218.417.23.6.31.45 #1.28 2.29.12.23. PF13 PF14 632 1.36.36.25.249.45.29.6.45.64 #2.29 2.35.12.23. PF13 PF14 832 1.36.36.312.311.514.29.6.45.64 #2.33 2.35.12.23. PF13 PF14 32 1.36.36.312.311.514.29.6.45.64 #2.33 2.35.12.29. PF13 PF14 42 1.36.36.375.374.575.35.6.53.79 #3.46 2.41.12 ll dimensions are in millimeters. Size x Pitch Knurled Smooth ap ap Min. Hole Size (Shank) Sheet In Sheet Max. Thickness +.8 P T 1 T 2 Driver Hole Max. ±.25 ±.64 ±.64 Nom. Nom. Size /L To dge 4.32 M3 x.5 PF13 PF14 M3 1.92.92 5.56 5.54 1.59 5.84 1.52 7.87 11.43 #1 7.11 2 7.37 3.5 5.84 M3.5 x.6 PF13 PF14 M3.5 1.92.92 6.35 6.33 11.43 7.37 1.52 11.43 16.26 #2 7.37 2 8.89 3.5 5.84 M4 x.7 PF13 PF14 M4 1.92.92 7.92 7.9 13.6 7.37 1.52 11.43 16.26 #2 8.38 2 8.89 3.5 5.84 M5 x.8 PF13 PF14 M5 1.92.92 7.92 7.9 13.6 7.37 1.52 11.43 16.26 #2 8.38 2 8.89 3.5 7.37 M6 x 1 PF13 PF14 M6 1.92.92 9.53 9.5 14.61 8.89 1.52 13.46 2.7 #3 11.68 2 1.41 3.5 PF-5
PF11M, PF12M, PF13M, ND PF14M WITH NTI-ROSS THRD THNOLOY Pennngineering is a licensee for M anti cross-threading technology. This patented design helps speed assembly and eliminates failures, repairs, scrap, downtime, and warranty service associated with thread damage. M is a registered trademark of M Inc. Four dimples on head designate metric thread. Driver size. ases assembly. ligns components. Improves assembly line productivity. Slides through clogged internal threads. T 2 T 1 P vailable without shoulder as s PF13 or PF14 Min. Float -.2 /.51 mm total. PF11M - 632 - BL PF11M PF12M PF13M PF14M and Material Finish ll dimensions are in inches. Size Knurled Smooth ap ap.112-4 PF11M PF12M (#4-4) PF13M PF14M.138-32 PF11M PF12M (#6-32) PF13M PF14M.164-32 PF11M PF12M (#8-32) PF13M PF14M.19-32 PF11M PF12M (#1-32) PF13M PF14M.25-2 PF11M PF12M (1/4-2) PF13M PF14M ll dimensions are in millimeters. Size Knurled Smooth ap ap Max. Min. Sheet Thickness Hole Size In Sheet P T 1 T 2 Driver Hole +.3 Max. ±.1 ±.25 ±.25 Nom. Nom. Size /L To -. dge.2. 44 1.36.36.219.218.417.26.6.31.47 #1.28 2.32.12.23. 632 1.36.36.25.249.45.29.6.45.64 #2.29 2.35.12.23. 832 1.36.36.312.311.514.29.6.45.64 #2.33 2.35.12.23. 32 1.36.36.312.311.514.29.6.45.64 #2.33 2.35.12.29. 42 1.36.36.375.374.575.35.6.53.8 #3.46 2.41.12 Max. Min. Hole Size Sheet In Sheet Thickness +.8 P T 1 T 2 Driver Hole Max. ±.25 ±.64 ±.64 Nom. Nom. Size /L To dge M3 x.5 5.8 PF11M PF12M M3 1.92.92 5.56 5.54 1.59 6.6 1.52 PF13M PF14M 2 8.13 3.5 7.87 11.94 #1 7.11 5.84 PF11M PF12M M3.5 x.6 M3.5 1.92.92 6.35 6.33 11.43 7.37 1.52 PF13M PF14M 2 8.89 3.5 11.43 16.26 #2 7.37 M4 x.7 5.84 PF11M PF12M M4 1.92.92 7.92 7.9 13.6 7.37 1.52 PF13M PF14M 2 8.89 3.5 11.43 16.26 #2 8.38 M5 x.8 5.84 PF11M PF12M M5 1.92.92 7.92 7.9 13.6 7.37 1.52 PF13M PF14M 2 8.89 3.5 11.43 16.26 #2 8.38 M6 x 1 7.37 PF11M PF12M M6 1.92.92 9.53 9.5 14.61 8.89 1.52 PF13M PF14M 2 1.41 3.5 13.46 2.32 #3 11.68 PF-6
NTI ROSS-THRD THNOLOY - HOW IT WORKS MISLIND XIS: This design offers users the benefits of self-aligning, anti cross-threading threads. THRDS M: s the threads come into contact, the patented anti cross-thread begins to cam over the female thread. THRDS DRIV NORMLLY: The design promotes alignment of the two thread helixes. The fasteners drive easily with reduced effort. OPTIONS FOR PF11M, PF12M, PF13M, ND PF14M PNL FSTNRS LTRNT RTINR MOUNTIN STYLS OPTIONL RSSS Broaching PF11PM PF11LSM PF11SM PF11LM Flare-in Floating Phillips TYP PFHV TM PNL FSTNR SSMBLIS Small, compact and low profile design for limited access areas. Two screw lengths. Universal slot/phillips recess standard. Six-lobe/slot combination available. PFHV - 632 - N 6-Lobe/Slot ombination Driver size. Four dimples on head designate metric thread. Slotted 6-Lobe vailable with six-lobe/slot combination drive ( PFHVLS) on special order. T 2 H Finish T 1 Patented. P ll dimensions are in inches. Min. Hole Size (Shank) Sheet In Sheet H P T 1 T 2 Driver Hole /L Size Max. Thickness +.3 Max. ±.1 ±.25 ±.5 ±.25 Nom. Nom. Size To dge -..112-4.216. PFHV 44.36.36.23.22.26.8 (#4-4) 1.316.95.26.436 #1.213.138-32.234. PFHV 632.36.36.219.218.276.92 (#6-32) 1.359.12.29.484 #2.23 ll dimensions are in millimeters. Min. Hole Size Size x (Shank) Sheet In Sheet H P T 1 T 2 Driver Hole /L Pitch Max. Thickness +.8 Max. ±.25 ±.64 ±.13 ±.64 Nom. Nom. Size To dge M3x.5 PFHV M3 M3.5x.6 PFHV M3.5 M4x.7 PFHV M4 5.55.92.92 5.5 5.49 6.95 2.3 1 7.56 1.9 6.69 11.25 #1 5.8 6.1.92.92 6 5.98 7.45 2.34 1 8.42 2.3 7.45 12.47 #2 6.3 6.59.92.92 6.4 6.38 7.85 2.79 1 9.39 2.7 8.5 14.1 #2 6.7 PF-7
TYP PF2 ND PFS2 PNL FSTNR SSMBLIS ssorted screw lengths for most applications. vailable in steel or stainless steel. Meets UL 58 operator access area requirements. Tool or finger operation. Most sizes available in three screw lengths. T 2 H Diagonal knurl identifies metric thread sizes. T1 PFS2-832 - 5 BN and Material Finish P SRTH PROOF PM Trademark Blue plastic retaining ring DuraBlack TM finish ll dimensions are in inches. Hole Size Min. In Sheet H P T (Shank) Sheet 1 T 2 Hole /L Size Stainless +.3 Max. ±.1 ±.16 ±.5 ±.25 Max. Nom. Steel Max. Thickness To dge Steel -..112-4 4.25. PFS2 PF2 44.6.6.265.264.312.72.36.54.25 (#4-4) 62.375.125 4.25..138-32 PFS2 PF2 632 62.6.6.281.28.344.375.72.125 (#6-32) 84 NS.5.25.36.54.28 5.312..164-32 PFS2 PF2 832 72.6.6.312.311.375.437.82.125 (#8-32) 94.562.25.45.69.31 5.312..19-32 PFS2 PF2 32 72.6.6.344.343.46.437.82.125 (#1-32) 94.562.25.45.69.34 6.375..25-2 PFS2 PF2 42 82 NS.6.6.413.412.468.5.97.125 (1/ 4-2) 4 NS.625.25.58.88.38 ll dimensions are in millimeters. Min. Hole Size Size x (Shank) Sheet In Sheet Stainless Pitch Steel Max. Thickness +.8 Steel M3 x.5 PFS2 PF2 M3 H P T 1 T 2 Hole /L Max. ±.25 ±.4 ±.13 ±.64 Max. Nom. To dge 4 6.4 1.53 1.53 6.73 6.71 7.92 1.83 62 NS 9.5 3.2 9.14 13.72 6.35 5 7.9 M4 x.7 PFS2 PF2 M4 72 NS 1.53 1.53 7.92 7.9 9.53 11.1 2.8 3.2 11.43 17.53 7.87 94 NS 14.3 6.4 5 7.9 M5 x.8 PFS2 PF2 M5 72 1.53 1.53 8.74 8.72 1.31 11.1 2.8 3.2 11.47 17.53 8.63 94 NS 14.3 6.4 6 9.5 M6 x 1 PFS2 PF2 M6 82 NS 1.53 1.53 1.49 1.47 11.89 12.7 2.46 3.2 14.73 22.35 9.65 4 NS 15.9 6.4 (NS) Not Stocked, available on special order. PF-8
TYP PF4 TM PNL FSTNR SSMBLIS Installs into stainless steel sheets. pproved for UL 195 service area access requirements. ssorted screw lengths for most applications. For use in sheets of HRB 88 or less. Driver size. PF4-832 - 5 T 2 T1 Four dimples on head designates metric thread. PM Trademark Blue plastic retaining ring US P Patented. ll dimensions are in inches. Size Min. (Shank) Sheet Max. Thickness Hole Size In Sheet P T 1 T 2 Driver Hole /L +.3 Max. ±.1 ±.16 ±.25 Max. Nom. Size To dge -..112-4 4.25. PF4 44.6.6.265.264.344 (#4-4) 62.375.125.138-32 (#6-32).164-32 (#8-32).19-32 (#1-32).37.54 #1.25 4.25. PF4 632 62.6.6.281.28.375.375.125.38.54 #2.28 84 NS.5.25 5.312. PF4 832 72.6.6.312.311.46.437.125.48.75 #2.31 94.562.25 5.312. PF4 32 72.6.6.344.343.437.437.125.49.75 #2.34 94.562.25 ll dimensions are in millimeters. Size x Pitch Min. Hole Size Min. Dist P T (Shank) Sheet In Sheet 1 T 2 Driver Hole /L Max. ±.25 ±.4 ±.64 Max. Nom. Size Max. Thickness +.8 To dge M3 x.5 PF4 M3 (NS) Not Stocked, available on special order. 4 6.4 1.53 1.53 6.73 6.71 8.74 62 NS 9.5 3.2 9.4 13.72 #1 6.35 5 7.9 M4 x.7 PF4 M4 72 NS 1.53 1.53 7.92 7.9 1.31 11.1 3.2 12.19 17.91 #2 7.87 94 NS 14.3 6.4 5 7.9 M5 x.8 PF4 M5 72 1.53 1.53 8.74 8.72 11.1 11.1 3.2 12.45 17.91 #2 8.63 94 NS 14.3 6.4 PF-9
TYP PF3 LOW-PROFIL PNL FSTNR SSMBLIS Satisfies many functional and cosmetic requirements. Large, slotted head for tool or finger operation. Low-profile design. Meets UL 58 operator access area requirements. Diagonal knurl identifies metric thread sizes. PF3-832 - 3 N Finish T 2 H T 1 SRTH PROOF DuraBlack TM finish Patented. ll dimensions are in inches. Size.112-4 (#4-4).138-32 (#6-32).164-32 (#8-32).19-32 (#1-32).25-2 (1/4-2) Min. (Shank) Sheet Max. Thickness Hole Size In Sheet H T 1 T 2 +.3 Max. ±.1 ±.15 ±.5 Max. Nom. -. PF3.3.3 PF31 44 3.38.4.23.22.46.3.22.325.595.26 PF32.58.6 PF3 NS.3.3 PF31 632 3.38.4.219.218.438.3.22.325.595.28 PF32.58.6 PF3 NS.3.3 PF31 832 3.38.4.25.249.468.3.27.33.6.29 PF32.58.6 PF3 NS.3.3 PF31 32 3.38.4.312.311.53.3.22.335.65.33 PF32.58.6 PF32 42 35.58.6.375.374.625.35.242.385.675.38 Hole /L To dge ll dimensions are in millimeters. Min. Hole Size H T Size x (Shank) Sheet In Sheet 1 T 2 Hole /L Max. ±.25 ±.4 ±.13 Max. Nom. Pitch Max. Thickness +.8 To dge M3 x.5 PF31 NS.97 1 M3 3 PF32 1.48 1.5 5.5 5.48 1.31 7.62 5.13 8.26 15.11 6.6 M4 x.7 PF31.97 1 M4 3 PF32 1.48 1.5 6.4 6.38 11.89 7.62 5.26 8.38 15.24 7.37 M5 x.8 PF31.97 1 M5 3 PF32 1.48 1.5 8 7.98 13.46 7.62 5.59 8.51 15.37 8.38 M6 x 1 PF32 NS M6 35 1.48 1.5 9.5 9.48 15.88 8.89 6.12 9.78 17.15 9.65 (NS) Not Stocked, available on special order. PF-1
TYP PF5 TM ND PF6 TM LOW-PROFIL PNL FSTNR SSMBLIS Satisfies many functional and cosmetic requirements. PF5 with large head and Phillips recess for tool or finger operation. vailable with six-lobe recess. PF5 (knurled cap) meets UL 58 operator access area requirements. PF6 (smooth cap) meets UL 195 tool only access area requirements. vailable in black. PF5-44 - 1 N roove on retainer identifies metric thread sizes. Driver size. Finish PF5 PF6 SRTH PROOF DuraBlack TM finish P T 2 H T 1 ll dimensions are in inches. Min. Hole Size Min. Dist H P T 1 T 2 Driver (Shank) Sheet In Sheet Hole /L Size Knurled Smooth Max. +.15 ±.25 ±.8 ±.25 Max. Nom. Size ap ap Max. Thickness +.3 -. -.5 To dge.112-4.23. PF5 PF6 44.3.3.23.22.46.27 (#4-4) 1.29.6.34.52 #1.26.138-32.23. PF5 PF6 632.3.3.219.218.438.27 (#6-32) 1.29.6.34.52 #2.28.164-32.23. PF5 PF6 832.3.3.25.249.468.217 (#8-32) 1.29.6.34.53 #2.29.19-32.23. PF5 PF6 32.3.3.312.311.53.225 (#1-32) 1.29.6.36.53 #2.33.25-2.28. PF52 PF62 42.58.6.375.374.625.246 (1/4-2) 1.34.6.395.6 #2.38 ll dimensions are in millimeters. Min. Hole Size Min. Dist H P T 1 T 2 Driver Size x Knurled Smooth (Shank) Sheet In Sheet Hole /L Max. +.4 ±.64 ±.2 ±.64 Max. Nom. Size Pitch ap ap Max. Thickness +.8 -.13 To dge M3 x.5 PF5 PF6 M3 5.84.77.8 5.5 5.48 1.3 5.26 1 7.37 1.52 8.64 13.21 #1 6.6 M3.5 x.6 PF5 PF6 M3.5 5.84.77.8 5.56 5.54 11.1 5.26 1 7.37 1.52 8.64 13.21 #2 7.1 M4 x.7 PF5 PF6 M4.77.8 6.4 6.38 11.9 5.84 5.51 8.64 13.46 #2 7.4 1 7.37 1.52 M5 x.8 PF5 PF6 M5.77.8 8 7.98 13.5 5.84 5.72 9.15 13.46 #2 8.4 1 7.37 1.52 M6 x 1 PF52 PF62 M6 1.47 1.5 9.5 9.48 15.9 7.11 6.25 1.4 15.24 #2 9.7 1 8.64 1.52 PF-11
TYP PF1 FLUSH-MOUNTD PNL SRW OMPONNTS head is flush in sheets as thin as.125 / 3.2 mm. remains captive in retainer when disengaged. For use in sheets of HRB 7 or less. PR1 Retainer PS1 B M N1 Receptacle N1 Receptical Nut PR1 Retainer T PS1 Manually Retracted Position P ll dimensions are in inches. UNIFID B T M P Min. Nom. ±.1 Nom..4.125.4.16.28.13 ll dimensions are in millimeters. MTRI B T M P Min. Nom. ±.25 Nom. 1 3.18 1.16 4.6 7.11 3.3 PS1 Flush-Mounted s H Diagonal knurl identifies metric thread sizes. PS1-832 - 4 T L ll dimensions are in inches. Size.112-4 (#4-4).138-32 (#6-32).164-32 (#8-32).19-32 (#1-32) H L T +.2 Nom. ±.1 Nom. -.6 PS1 44 4.18.75.33.13 PS1 632 4.21.75.33.13 PS1 832 4.25.75.33.13 PS1 32 4.28.75.33.13 ll dimensions are in millimeters. H L T Size x +.5 Nom. ±.25 Nom. Pitch -.15 M3 x.5 PS1 M3 4 4.7 1.91 8.38 3.3 M4 x.7 PS1 M4 4 6.3 1.91 8.38 3.3 M5 x.8 PS1 M5 4 7.1 1.91 8.38 3.3 PF-12
PR1 Self-linching Flush-Mounted Retainers B PR1-832 H ll dimensions are in inches. Hole Size Min. Sheet Min. Sheet in Sheet B H (Shank) for Self- for Flush Hole /L Size (1) +.3 Nom. Max. Nom. Nom. Max. linching Installation to dge -..112-4 (#4-4) PR1 44.125.5.125.281.195.28.31.75.31.138-32 (#6-32) PR1 632.125.5.125.312.225.311.34.75.33.164-32 (#8-32) PR1 832.125.5.125.344.255.343.37.75.34.19-32 (#1-32) PR1 32.125.5.125.375.29.374.41.75.36 ll dimensions are in millimeters. Min. Sheet Min. Sheet Hole Size B H Size x (Shank) for Self- for Flush in Sheet Hole /L (1) Nom. Max. Nom. Nom. Pitch Max. linching Installation +.8 to dge M3 x.5 PR1 M3 3.18 1.27 3.18 7.14 4.75 7.12 7.87 1.91 7.87 M4 x.7 PR1 M4 3.18 1.27 3.18 8.74 6.48 8.72 9.53 1.91 8.64 M5 x.8 PR1 M5 3.18 1.27 3.18 9.53 7.37 9.5 1.41 1.91 9.14 (1) 2B (unified) and 6H (metric) go gauge may stop at pilot end but class 3 (unified) and 4h (metric) screws will pass through with finger torque. N1 Self-linching Receptacle Nuts H F N1-832 - 1 ZI T Shank Finish ll dimensions are in inches. Hole Size Min. Shank In Sheet F H T (Shank) Sheet Hole /L Size +.3 Max. Nom. ±.1 Nom. ±.5 Max. Thickness To dge -..112-4 (#4-4) N1 44 1.38.4.187.186.28.13.126.24.22.138-32 (#6-32) N1 632 1.38.4.213.212.31.13.156.24.27.164-32 (#8-32) N1 832 1.38.4.25.249.34.13.187.24.28.19-32 (#1-32) N1 32 1.38.4.277.276.37.13.213.24.31 ll dimensions are in millimeters. Min. Hole Size Shank F H T Size x (Shank) Sheet In Sheet Hole /L Max. Nom. ±.25 Nom. ±.13 Pitch Max. Thickness +.8 To dge M3 x.5 N1 M3 1.97 1 4.75 4.73 7.11 3.3 3.2 6 5.59 M4 x.7 N1 M4 1.97 1 6.35 6.33 8.64 3.3 4.75 6 7.11 M5 x.8 N1 M5 1.97 1 7.4 7.1 9.53 3.3 5.41 6 7.87 PF-13
F1 Self-linching Floating Receptacle Nuts (Special order only) F F1-832 - 1 ZI T D Shank Finish ll dimensions are in inches. Hole Size Min. Shank In Sheet D F T (Shank) Sheet Hole /L Size +.3 Max. Max. Max. ±.1 ±.1 Max. Thickness To dge -..112-4 (#4-4) F1 NS 44 1.38.4.29.289.29.36.12.2.3.138-32 (#6-32) F1 NS 632 1.38.4.328.327.33.39.12.193.32.164-32 (#8-32) F1 NS 832 1.38.4.368.367.365.44.12.191.34.19-32 (#1-32) F1 NS 32 1.38.4.46.45.45.47.12.25.36 ll dimensions are in millimeters. Min. Hole Size Shank D F T Size (Shank) Sheet In Sheet Hole /L Max. Max. Max. ±.25 ±.25 x Pitch Max. Thickness +.8 To dge M3 x.5 F1 NS M3 1.97 1 7.37 7.34 7.37 9.15 2.59 5.8 7.62 M4 x.7 F1 NS M4 1.97 1 9.35 9.32 9.28 11.18 2.59 4.85 8.64 M5 x.8 F1 NS M5 1.97 1 1.31 1.29 1.29 11.94 2.59 6.53 9.14 (NS) Not Stocked, available on special order. Special pplication Note: For applications where the screw head may project above the sheet surface, PS1 screws may be used with PMSRT F fasteners as retainers. F fasteners are self-clinching and flush mounted in sheets as thin as.6 / 1.5 mm. s are installed by turning them through the threads of the F fasteners. For dimensions and engineering data on F fasteners see PM Bulletin F. H M H M T Max. Nom. Nom. Nom. T MTRI UNIFID PS1 with F Retainer (inches).6.75.21.13 PS1 with F Retainer (millimeters) 1.53 1.9 5.4 3.3 PF-14
TYP PF2P TM PHILLIPS RSS PNL FSTNR SSMBLIS pproved for UL 195 service area access requirements. ssorted screw lengths for most applications. Driver size. PF2P - 832-5 US Patented. SRTH PROOF DuraBlack TM finish P T 2 T1 Four dimples on head designates metric thread. PM Trademark Blue plastic retaining ring. ll dimensions are in inches. Size Min. (Shank) Sheet Max. Thickness Hole Size In Sheet P T 1 T 2 Driver Hole /L +.3 Max. ±.1 ±.16 ±.25 Max. Nom. Size To dge -..112-4 4.25. PF2P 44.6.6.265.264.312 (#4-4) 62.375.125.138-32 (#6-32).164-32 (#8-32).19-32 (#1-32).25-2 (1/4-2).37.54 #1.25 4.25. PF2P 632 62.6.6.281.28.344.375.125.38.54 #2.28 84 NS.5.25 5.312. PF2P 832 72.6.6.312.311.375.437.125.48.75 #2.31 94.562.25 5.312. PF2P 32 72.6.6.344.343.46.437.125.49.75 #2.34 94.562.25 6.375. PF2P 42 82 NS.6.6.413.412.468.5.125.62.95 #3.38 4 NS.625.25 ll dimensions are in millimeters. Size x Pitch Min. Hole Size Min. Dist P T (Shank) Sheet In Sheet 1 T 2 Driver Hole /L Max. ±.25 ±.4 ±.64 Max. Nom. Size Max. Thickness +.8 To dge M3 x.5 PF2P M3 4 6.4 1.53 1.53 6.73 6.71 7.92 62 NS 9.5 3.2 9.4 13.72 #1 6.35 5 7.9 M4 x.7 PF2P M4 72 NS 1.53 1.53 7.92 7.9 9.53 11.1 3.2 12.19 17.91 #2 7.87 94 NS 14.3 6.4 5 7.9 M5 x.8 PF2P M5 72 1.53 1.53 8.74 8.72 1.31 11.1 3.2 12.45 17.91 #2 8.63 94 NS 14.3 6.4 6 9.5 M6 x 1 PF2P M6 82 NS 1.53 1.53 1.49 1.47 11.89 12.7 3.2 15.75 22.99 #3 9.65 4 NS 15.9 6.4 (NS) Not Stocked, available on special order. PF-15
TYP PFF TM HYBRID TM FLOTIN PNL FSTNR SSMBLIS Molded-thru color knob. ompensates for up to.6 / 1.52mm mating hole misalignment. Tool or finger operation. Optional colors available. Installs into any panel material. Four dimples on head designate metric thread. Driver size. PFF - 32 - L 1 T 2 T 1 Shank Knob Style olor L PFF panel fasteners are shipped with mating washers. Patented. For color capabilities see page PF-32. W.25 /.64mm Nom. Shown with the standard slot/phillips recess and L style knob.(1) ll dimensions are in inches. Min. Shank L T 1 T 2 Driver Radial W Washer Size Max. ±.1 Nom. Nom. Nom. Nom. Size Float in Max. Part Sheet Number.19-32.315.154.468.668 PFF 32.283.594 (#1-32) 1.346.185.498.698 #2.3.411 PFFW-.216-24.39.16.54.698 PFF 1224.345.646 (#12-24) 1.341.191.534.728 #2.3.473 PFFW-12 ll dimensions are in millimeters. Min. Shank L T 1 T 2 Driver Radial W Washer Size x Max. ±.25 Nom. Nom. Nom. Nom. Size Float in Max. Part Pitch Sheet Number M5 x.8 PFF M5 8 3.91 11.89 16.97 7.19 15.9 1 8.79 4.7 12.65 17.73 #2.76 1.44 PFFW- M6 x 1 PFF M6 7.85 4.6 12.8 17.73 8.77 16.41 1 8.66 4.85 13.56 18.49 #2.76 12.2 PFFW-M6 (1) For special recess types consult our ngineering Department. For hole size and sheet thickness data, see charts on page PF-26. PF-16
TYP PFP TM HYBRID TM PNL FSTNR SSMBLIS Metal slot/phillips recess. Standard black BS knob. Steel retainer and screw. Optional colors available. Molded-thru color. vailable with six-lobe recess on special order. Four dimples on head designate metric thread. Shown with standard slot/phillips recess and L style knob. (1) Driver size. PFP - 632 - L 1 T 2 T 1 Patented. Knob Style Knob olor For color capabilities see page PF-32. P ll dimensions are in inches. Size.112-4 (#4-4).138-32 (#6-32).164-32 (#8-32).19-32 (#1-32) Min. Hole Size Total (Shank) Sheet In Sheet P T 1 T 2 Driver Hole /L Radial Max. Thickness +.3 Max. ±.1 ±.25 ±.25 Nom. Nom. Size To dge Float -. Min..23. PFP 44 1.36.36.23.22.542.29.6.436.636 #1.213.15 2.35.12.23. PFP 632 1.36.36.219.218.542.29.6.436.636 #2.23.2 2.35.12.23. PFP 832 1.36.36.25.249.594.29.6.436.636 #2.263.2 2.35.12.23. PFP 32 1.36.36.281.28.594.29.6.436.636 #2.294.2 2.35.12 ll dimensions are in millimeters. Min. Hole Size Size x (Shank) Sheet In Sheet Pitch Max. Thickness +.8 (1) For special drive types consult our ngineering Department. P T 1 T 2 Driver Max. ±.25 ±.64 ±.64 Nom. Nom. Size 5.84 Hole /L To dge M3 x.5 PFP M3 1.92.92 5.16 5.14 13.77 7.37 1.52 11.7 16.15 #1 5.41.38 2 8.89 3.5 5.84 M3.5 x.6 PFP M3.5 1.92.92 5.56 5.54 13.77 7.37 1.52 11.7 16.15 #2 5.84.51 2 8.89 3.5 5.84 M4 x.7 PFP M4 1.92.92 6.35 6.33 15.9 7.37 1.52 11.7 16.15 #2 6.68.51 2 8.89 3.5 5.84 M5 x.8 PFP M5 1.92.92 7.14 7.12 15.9 7.37 1.52 11.7 16.15 #2 7.47.51 2 8.89 3.5 Total Radial Float Min. Spring action of plastic fingers holds knob in retracted position. Photo represents - length screw. Shown here is the PFP panel fastener (custom color 2) threaded into a PM S nut. PF-17
TYP PFT TM HYBRID TM THUMBSRWS Internal, six-lobe metal recess plus slot in plastic knob. Standard black BS knob. Hand or tool actuated. olor matching capabilities. Molded-thru color. Driver size. T PFT L 632 - L 1 S Drive Knob Style Knob olor Shown with standard lobe drive and slotted knob. (1) For color capabilities see page PF-32. Patented. Three dimples on head designate metric thread. ll dimensions are in inches. Drive Size Max. S T Driver learance ±.1 ±.15 ±.15 ±.25 Max. ±.15 Size Hole.112-4.335 PFT L 44.75.35.5 (#4-4) 1.5.138-32.335 PFT L 632.75.35.5 (#6-32) 1.5.164-32.335 PFT L 832.75.4.58 (#8-32) 1.5.19-32.335 PFT L 32.75.4.58 (#1-32) 1.5.52.47 #1.143.65.47 #15.156.65.461 #2.191.65.461 #2.24 ll dimensions are in millimeters. Size x Pitch Drive Max. S T Driver learance ±.25 ±.4 ±.4 ±.64 Max. ±.4 Size Hole M3 x.5 PFT L M3 M3.5 x.6 PFT L M3.5 M4 x.7 PFT L M4 M5 x.8 PFT L M5 8.51 1.91 8.89 12.7 1 12.7 8.51 1.91 8.89 12.7 1 12.7 8.51 1.91 1.16 14.73 1 12.7 8.51 1.91 1.16 14.73 1 12.7 1.5 1.34 #1 3.73 1.25 1.34 #15 3.96 1.45 11.71 #2 4.78 1.65 11.71 #2 5.28 (1) For special knob or drive types consult our ngineering Department. PF-18
TYP PFK PNL FSTNR SSMBLIS For use in P boards and sheets of HRB 7 or less. PFK - 632-4 T 2 H T 1 Diagonal knurl identifies metric thread sizes. P PM trademark - Blue plastic retaining ring ll dimensions are in inches. Size.112-4 (#4-4).138-32 (#6-32) Min. Hole Size H P T 1 T (Shank) Sheet In Sheet 2 Hole /L ±.3 ±.1 ±.16 ±.5 ±.25 Max. Nom. Max. Thickness +.3 -. To dge 4.25. PFK 44 62 NS.6.6.265.283.312.375.72.125.36.54.2 84 NS.5.25 4.25. PFK 632 62.6.6.281.299.344.375.72.125.36.54.26 84 NS.5.25 ll dimensions are in millimeters. Min. Hole Size H P T 1 T Size x (Shank) Sheet In Sheet 2 Hole /L ±.8 ±.25 ±.4 ±.13 ±.64 Max. Nom. Pitch Max. Thickness +.8 To dge 4 6.4 M3 x.5 PFK M3 62 NS 1.53 1.53 6.73 7.19 7.92 9.5 1.83 3.2 9.14 13.72 5.8 84 NS 12.7 6.4 (NS) Not Stocked, available on special order. TYP PTL2 SPRIN-LODD PLUNR SSMBLIS Reverse side of sheet is flush when plunger is retracted. Quick lockout feature holds plunger in retracted position. For use in sheets of HRB 8 or less. vailable as type PSL2 without lockout feature on special order. T 2 H 1 PTL2-4 - 4 N TR 2 T 1 Plunger Diameter Plunger Finish D ll dimensions are in inches. Plunger Plunger Min. Hole Size D Diameter Sheet In Sheet +. 1 2 H T 1 T 2 TR Hole /L Max. ±.1 ±.1 ±.1 ±.1 ±.1 Nom. ±.5 Thickness +.3 -. -.5 To dge PTL2 4 4.6.328.327.25.5.46.31.17.595.895.43.34 PSL2 NS 4 4.6.328.327.25.5.46.31.17.51.78.35.34 ll dimensions are in millimeters. Plunger Plunger Min. Hole Size D Diameter Sheet In Sheet 1 2 H T 1 T 2 TR Hole /L Max. -.13 ±.25 ±.25 ±.25 ±.25 ±.25 Nom. ±.13 Thickness +.8 To dge PTL2 4 4 1.53 8.33 8.31 6.35 12.7 1.3 7.87 4.32 15.11 22.73 1.92 8.64 PSL2 NS 4 4 1.53 8.33 8.31 6.35 12.7 1.3 7.87 4.32 12.95 19.81 8.89 8.64 (NS) Not Stocked, available on special order. PF-19
ReelFast PNL FSTNR OMPONNTS ND SSMBLY DT RTINR Packaged on 13 recyclable reels of 465 pieces. Tape width is 24mm. Supplied with Kapton patch for vacuum pick up. Reels conform to I-481. R For Retainer ØD SMTPR - 6-1 T B Solder Pad Retainer Size Shank Finish ØH ll dimensions are in inches. ØH ØD Retainer Part Min. Sheet B R Hole Size In Sheet Min. Solder Number Max. Thickness ±.3 Max. Nom. ±.5 +.3. Pad SMTPR-6-1.6.6.167.249.375.325.25.396 ll dimensions are in millimeters. ØH ØD Retainer Part Min. Sheet B R Hole Size In Sheet Min. Solder Number Max. Thickness ±.8 Max. Nom. ±.13 +.8 Pad SMTPR-6-1 1.53 1.53 4.24 6.33 9.53 8.26 6.35 1.6 SRW Packaged in bags. L T vailable with six-lobe recess on special order. For Four dimples on head designate metric thread. Metal Phillips Drive PSHP - 632 - L 1 Knob Style (Lobed) olor (Standard Black) ll dimensions are in inches. L T Driver ±.1 ±.1 ±.1 Nom. Size PSHP 44 PSHP 632.51.663.44.542 1.57.723.51.663.44.542 1.57.723 #1 #2 ll dimensions are in millimeters. L T Driver ±.25 ±.25 ±.25 Nom. Size PSHP M3 PSHP M3.5 12.95 16.84 11.18 13.77 1 14.48 18.36 12.95 16.84 11.18 13.77 1 14.48 18.36 #1 #2 PF-2
SSMBLY (See page PF-29 for installation/assembly steps) Installed using conventional surface mount techniques. Simply snap screw into retainer to complete assembly. Black BS knob standard. Optional molded-thru colors available. When ssembled Spring action of plastic fingers holds screw in retracted position. PSHP SMTPR T 2 T 1 Patented. For color capabilities see page PF-32. P Board P ll dimensions are in inches. Part Number Retainer P T 1 T 2 Total Size Part Number ±.25 ±.25 Nom. Nom. Radial Float.112-4.188. PSHP 44 SMTPR-6-1 (#4-4) 1.248.26.138-32.188. PSHP 632 SMTPR-6-1 (#6-32) 1.248.26.478.646.15.478.646.2 ll dimensions are in millimeters. Part Number Retainer P T 1 T 2 Total Size x Pitch Part Number ±.64 ±.64 Nom. Nom. Radial Float M3 x.5 PSHP M3 M3.5 x.6 PSHP M3.5 4.78 SMTPR-6-1 1 6.3.66 4.78 SMTPR-6-1 1 6.3.66 12.14 16.41.38 12.14 16.41.51 PF-21
MTRIL & FINISH SPIFITIONS s Fastener Materials Standard Finishes Optional Finish For Use In Sheet Hardness: xternal, Bright Zinc Per Internal, NSI 4 Nickel STM 88 or 8 or 7 or 6 or NSI B1.1, 2 3 Heat- Series Passivated Over opper B 633 Less Less Less Less B1.1, 2B NSI/SM Series Treated Stain- and/or Flash S1 (5µm), on the on the on the on the NSI/SM B1.13M, 13M 6g Stainless arbon arbon cetal less BS Tested Per per STM III, Natural Black Black Rockwell Rockwell Rockwell Rockwell B1.13M, 6H (1) Steel Steel Steel luminum (4) Steel (3) STM 38 B689 olorless Finish nodize Nitride B Scale B Scale B Scale B Scale PF11 PF12 Knob Retainer Spring PF11M PF12M Knob Retainer Spring PF13 PF14 Knob Retainer Spring PF13M PF14M Knob Retainer Spring PF2 Retainer (2) Spring PF4 Retainer Spring PFS2 Retainer (2) Spring PFHV Retainer PF3 PF31 PF32 Retainer Spring PF5 PF6 ap Retainer Spring PR1 PS1 N1 F1 Part Number s for Finishes None N ZI None BL BN (1) s with all external plated threads, lass 2/6g, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/6h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) The blue plastic retaining rings are a PM trademark. The temperature limit is 2 F / 93. (3) Temperature limit is 2 F / 93. (4) Temperature range 32 F - 15 F / - 65. PF-22
MTRIL & FINISH SPIFITIONS (ontinued) s Fastener Materials Standard Finishes Optional Finishes For Use In Sheet Hardness: xternal, Bright Zinc Per lectro Matte Internal, NSI 4 Nickel STM Plated lectro- 8 or 7 or 6 or NSI B1.1, 2 3 Heat- Series Passivated Over B 633 Bright Tin STM Less Less Less B1.1, 2B NSI/SM Series Treated Stain- and/or opper S1 (5µm), Tin STM B 545 on the on the on the NSI/SM B1.13M, 13M 6g Stainless arbon arbon lumi- cetal less BS Tested Per Flash III, B 545, Natural Black Black lass Rockwell Rockwell Rockwell P B1.13M, 6H (1) Steel Steel Steel num (4) Steel (3) STM 38 per STM olorless lass B Finish nodize Nitride W/Preserva- B B B Board B689 W/Preserva- tive oating, Scale Scale Scale tive oating nnealed PF2P Retainer (2) Spring PFF Knob Retainer Washer PFP Knob Retainer PFT Knob PFK Retainer (2) Spring PTL2 PSL2 Retainer Plunger ReelFast Knob Retainer Part Number s for Finishes None N ZI T None BL BN DT (1) s with all external plated threads, lass 2/6g, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/6h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) The blue plastic retaining rings are a PM trademark. The temperature limit is 2 F / 93. (3) Temperature limit is 2 F / 93. (4) Temperature range 32 F - 15 F / - 65. PF-23
INSTLLTION (1) PF11 and PF12 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Dia. +.8 / +2 mm PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.26.437 83521 83518 632.39.468 83522 83519 832.39.531 83523 8352 32.39.531 83523 8435 42.48.598 84351 84352 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 6.6 11.1 83521 83518 M3.5 9.91 11.89 83522 83519 M4 9.91 13.49 83523 8352 M5 9.91 13.49 83523 8435 M6 12.19 15.19 84351 84352 NVIL PF13 and PF14 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Dia. +.8 / +2 mm PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.26.437 83521 83518 632.39.468 83522 83519 832.39.531 83523 8352 32.39.531 83523 8435 42.48.598 84351 84352 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 6.6 11.1 83521 83518 M3.5 9.91 11.89 83522 83519 M4 9.91 13.49 83523 8352 M5 9.91 13.49 83523 8435 M6 12.19 15.19 84351 84352 NVIL PF2/PFS2/PF2P 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Dia. +.8 / +2 mm PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.345.323 975226 97526 632.345.358 975227 975261 832.435.386 975228 975262 32.435.421 975229 975263 42.565.484 97523 975264 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 8.76 8.2 975226 97526 M4 11.5 9.8 975228 975262 M5 11.5 1.69 975229 975263 M6 14.35 12.29 97523 975264 NVIL (1) Punches and anvils should be hardened. PF-24
INSTLLTION (ontinued) PFHV 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Dia. +.8 / +2 mm PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.22.285 84688 97264 632.25.31 84689 97274 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 5.59 7.24 84688 97264 M3.5 6.35 7.65 84689 97274 M4 7.24 8.43 85439 9726 NVIL PF4 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into the anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Installation Requirements 1. Sheet hardness must be less than 88 on the Rockwell B scale. 2. Hole punch should be kept sharp to minimize work hardening around hole. 3. Fastener should be installed in punch side of hole. 4. Fastener should not be installed near bends or other highly cold worked areas where sheet hardness may be greater than 88 on the Rockwell B scale. Min. Dia. +.8 / +2 mm PUNH NVIL nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.345.358 975227 97526 632.345.39 97521243 975261 832.435.421 975229 975262 32.435.452 97521244 975264 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 8.76 9.9 975227 97526 M4 11.5 1.69 975229 975262 M5 11.5 11.48 97521244 975264 PF3 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Dia. +.8 / +2 mm PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.295.421 975216 97526 632.295.453 9752161 975261 832.31.484 9752162 975262 32.31.546 9752163 975263 42.365.64 9752164 975264 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 7.49 1.69 975216 97526 M4 7.87 12.29 9752162 975262 M5 7.87 13.87 9752163 975263 M6 9.27 16.26 9752164 975264 NVIL PF-25
INSTLLTION (ontinued) PFF 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil and workpiece over shank of fastener, and then place the washer over the shank of fastener. 3. With punch and anvil surfaces parallel, apply swaging force with flaring punch. 1/32 R Nom. 3 Nom. 45 Nom. FLRIN PUNH H I nvil Dimensions nvil Dimensions (in.) Punch Dimensions (in.) nvil Punch B D F H I Part Part ±.2 ±.2 ±.1 ±.2 ±.1 ±.3 ±.2 ±.4 Number Number 32.449.268.67.47.198-.21.25.44.16.32 86825 8672 1224.485.32.659.47.217-.22.236.468.18.36 8671 8673 F WSHR PNL nvil Dimensions (mm) Punch Dimensions (mm) nvil Punch B D F H I Part Part ±.5 ±.5 ±.3 ±.5 ±.3 ±.8 ±.5 ±.1 Number Number M5 11.4 6.81 15.42 1.19 5.3-5.11 5.21 1.26.41.81 86825 8672 M6 12.32 8.13 16.74 1.19 5.99-6.7 6.4 11.89.51 1.2 8671 8674 RSSD NVIL D B PFF panel fastener in custom color 2. PFF before flaring. PFF after flaring. Spring action plastic fingers holds knob in retracted position. PNL ONFIURTION 1 For applications where a space between mating panels is acceptable. D PNL ONFIURTION 2 For applications where a space between mating panels is not acceptable. D B Min. Max. H Max. D Hole Size Shank B in Sheet (1) H Sheet Min. +.3 Min. Thickness -. (2) PFF 32.31 -.63.125 1.64 -.94.16.344.472 PFF 1224.31 -.63.125 1.64 -.94.16.46.534 Shank B D Hole Size H Sheet Min. in Sheet (1) Min. Thickness +.8 (2) PFF M5.79-1.6 3.18 1 1.61-2.39 4.6 8.74 11.99 PFF M6.79-1.6 3.18 1 1.61-2.39 4.6 1.32 13.56 (1) Hole size may be as small as.1 /.3mm larger than the dimension if radial float is not required. (2) H dimension may be as small as.1 /.3mm larger than the W dimension if radial float is not required. PF-26
INSTLLTION (ontinued) PF5 and PF6 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Dia. +.8 / +2 mm PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.295.421 975216 97526 632.295.453 9752161 975261 832.31.484 9752162 975262 32.31.546 9752163 975263 42.365.64 9752164 975264 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 7.49 1.69 975216 97526 M3.5 7.49 11.51 9752161 975261 M4 7.87 12.29 9752162 975262 M5 7.87 13.87 9752163 975263 M6 9.27 16.26 9752164 975264 NVIL F1 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the nut comes in contact with the sheet material. PUNH nvil Dimensions NVIL nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.31.32 97526 975248 632.31.339 97527 975248 832.31.375 97528 975248 32.31.413 97529 975248 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 7.87 7.67 97526 975248 M4 7.87 9.53 97528 975248 M5 7.87 1.49 97529 975248 N1 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the nut comes in contact with the sheet material. PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.225.298 86124 975248 632.225.329 86735 975248 832.225.361 86736 975248 32.225.392 86174 975248 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 5.72 7.57 86124 975248 M4 5.72 9.17 86736 975248 M5 5.72 9.6 86174 975248 NVIL PF-27
INSTLLTION (ontinued) PR1 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into the mounting hole, preferably the punched side. 3. With punch and anvil surfaces parallel, apply squeezing force until the retainer is flush in the sheet. PUNH NVIL PFP 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the nut comes in contact with the sheet material. nvil Dimensions Dia. +.8 / 2mm nvil Dimensions (in.) B D nvil Part Punch Part ±.2 ±.2 ±.1 ±.2 Number Number 44.432.221.552.47 85413 8544 632.432.221.552.47 85413 85441 832.432.277.64.47 85414 85442 32.432.277.64.47 85414 85993 PUNH Min. Installation tooling is available from Pennngineering. nvil Dimensions (mm) B D nvil Part Punch Part ±.5 ±.5 ±.3 ±.5 Number Number M3 1.97 5.61 14.2 1.19 85413 8544 M3.5 1.97 5.61 14.2 1.19 85413 85441 M4 1.97 7.4 15.34 1.19 85414 85442 M5 1.97 7.4 15.34 1.19 85414 85993 NVIL B pply squeezing force to the top of the screw (not to plastic knob). D PFK 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Dia. +.8 / +2 mm PUNH nvil Dimensions nvil Dimensions (in.) nvil Part Punch Part ±.2 ±.2 Number Number 44.32.323 975226 97526 632.32.358 975227 975261 nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M3 8.13 8.2 975226 97526 NVIL PF-28
INSTLLTION (ontinued) PTL2 1. Punch or drill properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Min. Pin Dia. +.8 / +2 mm PUNH nvil Dimensions NVIL Plunger nvil Dimensions (in.) Diameter nvil Part Punch Part ±.2 ±.2 Number Number 4.585.52 97521245 972133 Plunger nvil Dimensions (mm) Diameter nvil Part Punch Part ±.5 ±.5 Number Number 4 14.86 13.21 97521245 972133 ReelFast Panel Fastener Solder paste applied to pad on PB. Retainer soldered in place using standard surface mount techniques. snapped in place. ReelFast product performance is dependent upon application variables. We will be happy to provide samples for you to install. If required, we can also test your installed hardware and provide you with specific performance data. PF-29
PRFORMN DT (1) Test Sheet Material luminum old-rolled Steel Installation Pushout Installation Pushout (lbs.) (lbs.) (lbs.) (lbs.) 44 15 8 25 145 PF11 632 2 95 35 15 PF12 832/32 3 1 45 16 42 35 15 5 195 44 15 8 25 145 PF13 632 2 95 35 15 PF14 832/32 3 1 45 16 42 35 15 5 195 44 24 24 3 3 PFS2 632 27 275 35 35 PF2 832 29 3 38 4 PF2P 32 3 4 4 5 42 35 4 5 6 PFHV 44 17 18 22 118 632 185 117 24 128 44 22 64-185(3) (4) (4) PF3 632 24 66-19(3) (4) (4) PF31 832 28 68-2(3) (4) (4) PF32 32 35 72-26(3) (4) (4) 42 43 (2) (4) (4) 44 22 64 22 64 PF5 632 24 66 24 66 PF6 832 28 68 28 68 (5) 32 35 72 35 72 PF52 PF62 42 43 3 46 34 44 15 215 3 3 F1 632 2 24 3 3 832 2 25 3 3 32 2 3 35 4 44 25 95 36 13 N1 632 25 15 4 145 832 3 11 5 18 32 35 12 63 2 44 21 (2) 3 (2) PR1 632 21 (2) 3 (2) 832 21 (2) 36 (2) 32 24 (2) 42 (2) PSL2 PTL2 (2) 3 4 4 5 Test Sheet Material luminum old-rolled Steel Installation Pushout Installation Pushout (kn) (N) (kn) (N) M3 6.7 355 11.1 645 PF11 M4/M5 13.3 445 2 71 PF12 M6 15.6 465 22.2 865 M3 6.7 355 11.1 645 PF13 M4/M5 13.3 445 2 71 PF14 M6 15.6 465 22.2 865 M3 1.7 168 13.3 1334 PFS2 M4 12.9 1334 16.9 1779 PF2 M5 13.3 1779 17.8 2224 PF2P M6 15.6 1779 22.2 2669 M3 8.1 516 1.5 564 PFHV M3.5 8.8 561 11.4 614 M4 9.4 599 12.1 656 M3 9.8 285-823(3) (4) (4) PF3 M4 12.5 32-89(3) (4) (4) PF31 M5 15.6 32-1156(3) (4) (4) PF32 M6 19.1 1423 (4) (4) M3 9.8 284 9.8 284 PF5 M3.5 1.7 294 1.7 294 PF6 M4 12.5 32 12.5 32 (5) M5 15.6 32 15.6 32 PF52 PF62 M6 19.1 1334 2.5 1512 M3 6.7 956 13.3 1334 F1 M4 8.9 1112 13.3 1334 M5 8.9 1335 15.6 1779 M3 11.1 423 16 578 N1 M4 13.3 489 22.2 8 M5 15.6 534 28 89 M3 9.3 (2) 13.3 (2) PR1 M4 9.3 (2) 16 (2) M5 1.7 (2) 18.7 (2) PSL2 PTL2 (2) 13.3 1779 17.8 2224 PFF Max. Rec. Tightening Torque (in. lbs.) Swaging Force (lbs.) Pushout (lbs.) 32 21 6 1 1224 21 8 12 (1) The installation and pushout values reported are averages when all installation specifications and procedures are followed. Variations in mounting hole size, sheet material and installation force (or swaging force for PFF) will affect this data. Performance testing of this product in your application is recommended. We will be happy to provide samples for this purpose. (2) Not applicable. PFF Max. Rec. Swaging Tightening Pushout Force Torque (N) (kn) (N m) M5 2.37 2.67 445 M6 2.37 3.56 534 (3) Pushout depends on shank length. (4) an be used in cold-rolled steel provided sheet hardness does not exceed Rockwell B 6. (5) To obtain these values the aluminum test sheet thickness should be.3 to.4 /.76mm to 1.2mm, HRB 15 to 35 and the cold-rolled steel sheet should be.3 to.4 /.76mm to 1.2mm, HRB 45 to 65. PF-3
PRFORMN DT (1) (ontinued) PFP Max. Rec. old-rolled Steel 552-H34 luminum Tightening Installation Pushout Installation Pushout Torque (lbs.) (lbs.) (lbs.) (lbs.) (in. lbs.) 44 1 21 8 13 73 632 15 22 114 15 75 832 21 24 126 16 8 32 21 3 151 2 88 PFP Max. Rec. old-rolled Steel 552-H34 luminum Tightening Installation Pushout Installation Pushout Torque (kn) (N) (kn) (N) (N m) M3 1.13 9.3 355 5.8 325 M3.5 1.7 9.8 57 6.7 335 M4 2.37 1.7 56 7.1 355 M5 2.37 13.3 672 8.9 4 Test Sheet Material FR-4 Fiberglass Installation Pushout (lbs.) (lbs.) PFK 44 25 55 632 4 6 Test Sheet Material FR-4 Fiberglass Installation Pushout (kn) (N) PFK M3 1.1 245 Test Sheet Material 34 Stainless Steel Installation Pushout (lbs.) (lbs.) PF4 44 91 35 632 13 4 832 18 45 32 118 55 Test Sheet Material 34 Stainless Steel Installation Pushout (kn) (N) M3 4.5 1557 PF4 M4 48 22 M5 52.5 2447 (1) The installation, push out values reported are averages when all installations and procedures are followed. Variations in mounting hole size, sheet material and installation force will affect this data. Performance data testing of this product in your application is recommended. We will be happy to provide samples for this purpose. For PFS, tests were performed at room temperature and results are temperature dependent. PF-31
OLOR PBILITIS For s PFT, PFP, PFF, and ReelFast PF hoose a knob color code and add it to the end of the standard part number. The colors shown (except for black) are non-stocked standards and available on special order. Since actual color knob and retainer may vary slightly from those represented, we recommend that you request samples for color verification. If you require a custom color or you need a color matched knob or retainer, please contact us. Blue 6 Violet 7 reen 5 Red 2 Yellow 4 Orange 3 Standard Black 1 To be sure that you are getting genuine PM brand panel fasteners, look for the PM stamp, dimple, or two groove trademark. RoHS compliance information can be found on our website. Specifications subject to change without notice. heck our website for the most current version of this bulletin. PF-32-46384