FAX:

We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. However, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: -888-996-79 FAX: -866-873-353 gameroom@escaladesports.com Or write to: Escalade Sports Customer Service Department P.O. Box 889 Evansville, IN 47706 Please have your date code when inquiring about parts. When contacting Escalade Sports please provide your model number, date code (if applicable), and part number if requesting a replacement part. These numbers are located on the product, packaging, and in this owners manual. Your Model Number: Date Code: Purchase Date: G054W -G054W- -WJ PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 03 Escalade Sports For Customer Service Call -886-996-79

IMPORTANT! READ EACH STEP IN THIS MANUAL BEFORE YOU BEGIN THE ASSEMBLY. THREE ADULTS ARE REQUIRED TO ASSEMBLE THIS ATOMIC 7FT -IN- FLIP TOP GAME TABLE Tools Required: Wrench T included with the table Phillips Screwdriver Furniture Polish and Cloth An electric screwdriver is helpful in assembly. However, please set a low torque and use extreme caution with an electric screwdriver because you could overtighten the hardware and strip the screws. Assembly Tips Make sure you understand the following tips before you begin to assemble your flip table.. Start all bolts by hand before tightening.. Some drawings or images in this manual may not look exactly like your product. Please read and understand the text before starting each assembly step. R E A D A N D F O L L O W A L L A S S E M B L Y, O P E R A T I O N, A N D S A F E T Y I N S T R U C T I O N S C A R E F U L L Y. A T L E A S T T W O A D U L T S A R E N E E D E D T O P U T T H I S G A M E T A B L E T O G E T H E R. 03 Escalade Sports For Customer Service Call -886-996-79

HARDWARE IDENTIFIER (To Scale) H - 4 x 44mm Phillips Flat Head Screw (0) H - 4 x 38mm Phillips Flat Head Screw (34) H3-3.5 x 3mm Phillips Washer Head Screw (8) (Not to Scale) H4-8 x 8mm Hex Head Bolt (8) - 8 x 9mm Flat Washer (8) H7-Barrel Nut (8) T - Wrench () H6-8 x 63mm Hex Head Bolt (8) H8-8 x 00mm Hex Head Bolt (4) H9-4 x 5mm Phillips Flat Head Screw (6) (Not to Scale) H3 - M0 Hex Nut () (Not to Scale) H4 - Leg Leveler (4) H0 - Male Pivot Assembly () H - M0 Acorn Nut () H - M0 x 5mm Flat Washer (4) - 4 x mm Phillips Round Head Screw () H6-3 x 6mm Phillips Washer Head Screw (4) H7-4 x 50mm Phillips Flat Head Screw () H8-4 x 44mm Phillips Washer Head Screw (4) H9-4 x 44mm Phillips Flat Head Screw (4) H0-3 x 5mm Phillips Flat Head Screw (4) PARTS IDENTIFIER (Not to Scale) P - Pool Table () (Red Cloth) P - Hockey Table with C Blower Motor () P3 - Right Leg () P4 - Left Leg ()! WARNING: CHOKING HAZARD Small parts. Not for children under 3 yrs. 03 Escalade Sports 3 For Customer Service Call -886-996-79

PARTS IDENTIFIER (Not to Scale) P5 - Right Leg Panel () P6 - Left Leg Panel () P7 - Goal Box Support Frame with Curved (4) P8 - Goal Box Support Frame (4) ATOMIC P9 - End Frame Panel () P0 - Goal Box Panel () P - Frame Bottom Board () P - End Top Rail with Corner Caps Attached () P3 - L-Frame Lock (4) P4 - Leg Connecting Panel () P5 - Leg Panel Stiffener () P6 - Ball Storage Tray () P7 - Outer Apron with Cord Hole () P8 - Outer Apron without Cord Hole () P9S - Small Cue Clip () P9L - Large Cue Clip () P0 - Triangle Holder () P - Round Plastic for Cord Hole () P - Screw Covers (4) P3 - Barrel Nut Covers (8) P4 - Cord Holder () P5 - Female Pivot Bushing() ACCESSORY IDENTIFIER (Not to Scale) A - Pool Ball Set () A - Pool Cloth Brush () A3 - Plastic Triangle () A4 - Cue Chalk () A5 - Cue stick () A6 - Red Striker () A7 - Red Puck () A8 - Striker Felt Pad ()! WARNING: CHOKING HAZARD Small parts. Not for children under 3 yrs. 03 Escalade Sports 4 For Customer Service Call -886-996-79

CAREFULLY LIFT UP THE AIR HOCKEY PLAYFIELD AND REMOVE ALL ASSEMBLY PARTS, BEING SURE TO CHECK ALL INNER TABLE COMPARTMENTS FOR PARTS. FIND A CLEAN LEVEL PLACE TO BEGIN ASSEMBLY. WE RECOMMEND BUILDING THE TABLE IN THE BOX TOP TO PROTECT PARTS DURING ASSEMBLY. PARTS REQUIRED 8 pcs - H Phillips Flat Head Screw pcs - P3 Right Leg pcs - P Frame Bottom Board 8 pcs - H4 Hex Head Bolt pcs - P4 Left Leg pc - T Wrench 8 pcs - Flat Washer pcs - P9 End Frame Panel STEP : Secure P9 End Frame Panel to P Frame Bottom Board using H Screws as shown in FIGURE A. Attach the assembly from FIGURE A to P3 Right Leg and P4 Left Leg by insert H4 Bolts and Washers from inside of leg as shown in FIGURE B. Use T Wrench to tighten H4 Bolts. Repeat with other set of legs. Please note Pre-Drilled holes on both P9 & P Grooves on this side. P9 FIGURE B Steel inserts nuts must be on bottom P4 FIGURE A P H Be careful not to strip these screws. All H Screws must be tight - but not stripped. H4 H4 P3 PARTS REQUIRED 0 pcs - H Phillips Flat Head Screw pcs - P4 Leg Connecting Panel pcs - P5 Leg Panel Stiffener STEP : Install P5 Leg Panel Stiffeners to P4 Leg Connecting Panels using H Screws as shown in FIGURE. Important Note: Be careful not to strip these screws. All H Screws must be tight - but not stripped. Please note pilot holes on this top. Black laminate on this side. H H P5 H H H Please note Pre-Drilled holes on this side. P4 FIGURE 03 Escalade Sports 5 For Customer Service Call -886-996-79

PARTS REQUIRED 8 pcs - Flat Washer 8 pcs - H6 Phillips Round Head Screw pcs - P9L Large 8 pcs - H6 Hex Head Bolt 4 pcs - H8 Phillips Washer Head Screw Cue Clip 8 pcs - H7 Barrel Nut pcs - P9S Small Cue Clip pc - T Wrench STEP 3: With the help of another adult, attach the assembly from STEP (FIGURE ) to the assembly from STEP (FIGURE B) using H6 Hex Bolts with Flat Washers and H7 Barrel Nuts as shown in FIGURE 3. Do Not Tighten H6 Bolts at this time. Next, secure P5 Leg Panel Stiffener using H8 Screws as shown in FIGURE 3. Use T Wrench to tighten H6 Bolts. Attach P9S Small & P9L Large Cue Clips to P5 Leg Panel Stiffeners using pre-drilled holes with H6 Screws as shown in FIGURE 3. Important Note: Be careful not to strip these screws. All H6 & H8 Screws must be tight - but not stripped. Assembly from STEP. P9S (Small) P9L (Large) H6 FIGURE 3 H8 P5 P9S (Small) P9L (Large) H6 H6 H7 H8 Tighten, But do not overtighten all H6 Bolts. P4 Assembly from STEP. Install each P4/P5 (Assembly from STEP ) by making sure the 5(five) black barrel nuts are facing inside of table. PARTS REQUIRED 4 pcs - H4 Leg Leveler STEP 4: Thread H4 Leg Levelers onto each P3 Right Leg and P4 Left Leg as shown in FIGURE 4. FIGURE 4 P3 P4 H4 P3 H4 P4 H4 H4 03 Escalade Sports 6 For Customer Service Call -886-996-79

PARTS REQUIRED 6 pcs - H9 Phillips Flat Head Screw pcs - H3 Hex Nut pcs - H0 Male Pivot Assembly pc - P Pool Table pcs - H Flat Washer pc - T Wrench STEP 5: Attach H0 Male Pivot Assembly to each end apron using H9 Screws as shown in FIGURE 5 and DETAIL A. Secure each H0 Male Pivot Assembly with H Washer and H3 Nut as shown in FIGURE 5 and DETAIL A. Use T Wrench to tighten each H3 Nut. Important Note: Be careful not to strip these screws. All H9 Screws must be tight - but not stripped. P H H3 FIGURE 5 DETAIL A H9 H0 H9 H3 H0 H BEFORE INSTALLING PLAYFIELD SCREWS - PLEASE BE SURE ALL PARTS HAVE BEEN REMOVED FROM INNER CABINET AND AIR MOTOR CORD IS BROUGHT THROUGH THE HOLE IN SIDE PANEL. PARTS REQUIRED 4 pcs - H Phillips Washer Head Screw pc - P Hockey Table STEP 6: With the help of another adult, carefully install P Hockey Table into P Pool Table using H Screws as shown in FIGURE 6. IMPORTANT, be sure to feed the plug end from the fan motor through the hole in the side apron. Be careful not to strip these screws. All H Screws must be tight - but not stripped. P FIGURE 6 H P Motor Cord Do not run cord through Side Pocket hole. Use holes beside the Side Pocket. 03 Escalade Sports 7 For Customer Service Call -886-996-79 H

PARTS REQUIRED pc - P7 Outer Apron with Cord Hole pc - P8 Outer Apron without Cord Hole STEP 7: To install P7 Outer Apron with Cord Hole, please feed the cord plug end back inside the hole in side apron. Carefully insert and sleave P7 Outer Apron with Cord Hole and P8 Outer Apron without Cord Hole as shown in FIGURE 7. White laminate face outside. FIGURE 7 P8 P7 White laminate face outside. This hole is offset and must match this hole. Cord Plug PARTS REQUIRED 4 pcs - H0 Phillips Flat Head Screw pc - P Round Plastic for Cord Hole pcs - P5 Female Pivot Bushing STEP 8: Feed the plug end again through the hole in the side apron as shown in FIGURE 8A. Attach P Round Plastic for Cord Hole as shown in FIGURE 8B. Install four (4) pcs H0 Screws on each end of the side apron as shown in FIGURE 8B. Insert P5 Female Pivot Bushing onto each H0 Male Pivot Assembly on each end of table as shown in FIGURE 8B. NOTE: The P5 is not permanently attached until STEP #0. FIGURE 8A Do not run cord through side pocket holes. Please use the holes directly beside the side pocket. H0 H0 Cord Plug P5 H0 FIGURE 8B P5 P H0 End of P7 & P8 Outer Apron must be flush with table end apron. H0 Note: Pilot Holes 03 Escalade Sports 8 For Customer Service Call -886-996-79

! WARNING: THIS STEP REQUIRES THREE OR MORE ADULTS. 3rd adult helps to insure P5 Female Pivot Bushing / H0 Male Pivot Assembly slides down into slot on each end of table correctly. P5 H0 CAUTION: PINCH POINT! STEP 9: With the help of another adult, carefully lift the assembly from STEP 8 (FIGURE 8B) to the assembly from STEP 4 (FIGURE 4) as shown in FIGURE 9. Assembly from STEP 8. FIGURE 9 CAUTION: PINCH POINT! CAUTION: PINCH POINT! Two () adults lift from each side to install. Assembly from STEP 4. PARTS REQUIRED pcs - H Acorn Nut 6 pc - H6 Screw pcs - H Flat Washer pc - P4 Cord Clip STEP 0: Secure the assembly from STEP 8 (FIGURE 8B) and the assembly from STEP 4 (FIGURE 4) using H6 Screws as shown in FIGURE 0. Secure P5 Female Pivot Bushing with H6 Screws using Pre-Drilled holes shown on P9 End Frame Panel. All H6 Screws must be tight - but not stripped. Secure assembly using H Washer with H Acorn Nuts as shown in FIGURE 0. Use T Wrench to tighten H Acorn Nuts. Peel the backing off P4 Cord Clip and attach to a side of the table as shown in FIGURE 0. H H H H H6 P9 P5 FIGURE 0 P4 H6 Secure P5 Female Pivot Bushing with H6 Screws using Pre-Drilled holes shown on P9 End Frame Panel. PEEL & ATTACH 03 Escalade Sports 9 For Customer Service Call -886-996-79 P4

PARTS REQUIRED pcs - H Phillips Flat Head Screw 4 pcs - P8 Goal Box Support Frame 4 pcs - P7 Goal Box Support Frame with Curved pcs - P0 Goal Box Panel STEP : Rotate table approximately 90 degrees as shown. With the help of another adult hold the table in this position to install P7 Goal Box Support Frames with Curved and P8 Goal Box Support Frames using H Screws as shown in FIGURE A. Slide P0 Goal Box Panels between P7 Goal Box Support Frames with Curved on each end of table as shown in FIGURE B. Important Note: Be careful not to strip these screws. All H Screws must be tight - but not stripped. CAUTION! PINCH POINTS ROTATE TABLE ONLY WITH ADULT SUPERVISION Groove face inside. P7 P8 P8 Pilot hole on this side. P8 Groove face inside. H P7 P8 P8 P7 H H H FIGURE A P7 H H Atomic Jelly logo on this side. P0 P0 P7 ATOMIC FIGURE B P7 03 Escalade Sports 0 For Customer Service Call -886-996-79

PARTS REQUIRED pcs - Flat Washer pcs - H7 Phillips Flat Head Screw 4 pcs - P3 L-Frame Lock 4 pcs - H8 Hex Head Bolt pcs - P End Top Rail pc - T Wrench STEP : With the help of another adult, hold the table in this position to install P3 L-Frame Locks to each () leg assembly. Place Washer on H8 Bolt, insert bolt and washer upward through leg assembly, through Washer, through P3 L-Frame Lock, through Washer, and finally thread into bottom side of P End Top Rail as shown in FIGURE. DO NOT OVERTIGHTEN H8 BOLTS AS P3 L-FRAME LOCKS MUST BE FREE TO PIVOT. Repeat with other legs. Next, Secure the P End Top Rail using H7 Screws as shown in FIGURE. Important Note: Be careful not to strip these screws. All H7 Screws must be tight - but not stripped. Repeat this procedure on other leg assembly. H7 H7 CAUTION! PINCH POINTS ROTATE TABLE ONLY WITH ADULT SUPERVISION P P3 ATOMIC P3 H8 FIGURE DO NOT OVERTIGHTEN H8 BOLTS AS P3 L-FRAME LOCKS MUST BE FREE TO PIVOT. H8 03 Escalade Sports For Customer Service Call -886-996-79

ATOMIC ATOMIC STEP 3: Place all L-Frame Locks into closed position to lock table as shown in FIGURE 3A. Install P5 Right Leg Panel and P6 Left Leg Panel using H9 Screws as shown in FIGURE 3A. Stick P Screw Covers to cover H9 Screws if needed as shown in FIGURE 3B. Stick P3 Barrel Nut Covers to cover H7 Barrel Nuts if needed as shown in FIGURE 3B. Repeat procedure at opposite end of table. PARTS REQUIRED 4 pcs - H9 Phillips Flat Head Screw pcs - P6 Left Leg Panel pcs - P5 Right Leg Panel 4 pcs - P Screw Covers 8 pcs - P3 Barrel Nut Covers Lock Position P6 FIGURE 3A White laminate on this side. H9 P5 P FIGURE 3B P3 P P3 03 Escalade Sports For Customer Service Call -886-996-79

ATOMIC PARTS REQUIRED 8 pcs - H3 Phillips Washer Head Screw pcs - P6 Ball Storage Tray pcs - Phillipls Round Head Screw pc - P0 Triangle Holder STEP 4: Attach P6 Ball Storage Trays at each table end using H3 Screws as shown in FIGURE 4. Important Note: Please install P6 Ball Storage Trays so the bottom pre-drilled holes for P0 Triangle Holder face the inside of the tableas shown in DETAIL B. Attach one P0 Triangle Holder on bottom side of P6 Ball Storage Tray using pre-drilled holes with Screws as shown in FIGURE 4 and DETAIL B. Important Note: Be careful not to strip these screws. All H9 Screws must be tight - but not stripped. FIGURE 4 P6 H3 P0 Note: Cue Stick Storage Clips. H3 P6 DETAIL B Please install P6 Ball Storage Trays so the bottom pre-drilled holes for P0 Triangle Holder face the inside of the table. Please install P0 Triangle Holder back far enough on bottom of P6 Ball Storage Tray so it can not be a trip hazard. P0 Pre-Drilled Pilot Holes 03 Escalade Sports 3 For Customer Service Call -886-996-79

ATOMIC WARNING:!! LIFTING POINTS: FOR FINAL PLACEMENT OF FLIP TABLE PLEASE MAKE SURE ALL FOUR (4) P3 L-FRAME LOCKS ARE IN LOCK POSITION, THEN FOUR (4) ADULTS LIFT THE TABLE. ADULTS SHOULD LIFT TABLE BY PLACING HANDS ON EACH SIDE OF THE LEG AS SHOWN IN FIGURE 5. P3 L-FRAME LOCKS MUST IN LOCK POSITION. FIGURE 5 IMPORTANT! LIFTING POINT. IMPORTANT! LIFTING POINT. 03 Escalade Sports 4 For Customer Service Call -886-996-79

CAUTION: ROTATING YOUR TABLE DO NOT ALLOW CHILDREN TO ROTATE THIS TABLE This table should be rotated by ADULTS only. To release the table bed, open the frame locks at each corner. Be sure no one is in the way, then SLOWLY rotate the bed. After rotating the bed, close the frame locks to lock the table. Congratulations! You have now assembled your game table. Please note the Care and Use instructions below to insure many years of trouble free use of your game table. CARE AND USE OF YOUR TABLE. Use only a suitable 0v AC household outlet, and insure the cord is not a trip hazard.. Spray furniture polish is recommended to both protect the hockey play field and increase the puck speed. Apply and wipe off with the air motor on. Use spray furniture polish to clean all exterior surfaces of your game table. 3. Use the table brush provided to clean the cloth on the table. 4. You may use a vacuum cleaner with the brush attachment to clean the cloth on the pool table should it become necessary. 5. This product is intended for INDOOR use only. 6. DO NOT sit, climb or lean on the table. 7. DO NOT drag the table when moving it. This will damage the legs. 8. DO NOT set drinks on the table. 9. The purchase of billiard table cover will help protect and keep your table clean while not in use. 03 Escalade Sports 5 For Customer Service Call -886-996-79

PRODUCT PARTS LIST FOR MODEL # G054W Key# Part# Description Qty. 054WJH 054WJH 054WJH3 054WJH4 054WJ 054WJH6 054WJH7 054WJH8 054WJH9 054WJH0 054WJH 054WJH 054WJH3 054WJH4 054WJ 054WJH6 054WJH7 054WJH8 054WJH9 054WJH0 054WJT 054WJP 054WJP 054WJP3 054WJP4 054WJP5 054WJP6 054WJP7 054WJP8 054WJP9 054WJP0 054WJP 054WJP 054WJP3 054WJP4 054WJP5 054WJP6 054WJP7 054WJP8 054WJP9S 054WJP9L 054WJP0 054WJP 054WJP 054WJP3 054WJP4 054WJP5 054WJA 054WJA 054WJA3 054WJA4 054WJA5 054WJA6 054WJA7 054WJA8 054WJC 054WJK 054WJM H H H3 H4 H6 H7 H8 H9 H0 H H H3 H4 H6 H7 H8 H9 H0 T P P P3 P4 P5 P6 P7 P8 P9 P0 P P P3 P4 P5 P6 P7 P8 P9S P9L P0 P P P3 P4 P5 A A A3 A4 A5 A6 A7 A8 C K M 4 x 44 mm Phillips Flat Head Screw 4 x 38 mm Phillips Flat Head Screw 3.5 x 3 mm Phillips Washer Head Screw 8 x 8 mm Hex Head Bolt 8 x 9 mm Flat Washer 6 x 63 mm Hex Head Bolt Barrel Nut 8 x 00 mm Hex Head Bolt 4 x 5 mm Phillips Flat Head Screw Male Pivot Assembly M0 Acorn Nut M0 x 5 mm Flat Washer M0 Hex Nut Leg Leveler 4 x mm Phillips Round Head Screw 3 x 6 mm Phillips Washer Head Screw 4 x 50 mm Phillips Flat Head Screw 4 x 44 mm Phillips Washer Head Screw 4 x 44 mm Phillips Flat Head Screw 3 x 5 mm Phillips Flat Head Screw Wrench Pool Table (Red Cloth) Hockey Table (No Blower Motor) Right Leg Left Leg Right Leg Panel Left Leg Panel Goal Box Support Frame with Curved Goal Box Support Frame End Frame Panel Goal Box Panel Frame Bottom Board End Top Rail with Corner Caps Attached L-Frame Lock Leg Connecting Panel Leg Panel Stiffener Ball Storage Tray Outer Apron with Cord Hole Outer Apron without Cord Hole Small Cue Clip Large Cue Clip Triangle Holder Round Plastic for Cord Hole Screw Covers Barrel Nut Covers Cord Holder Female Pivot Bushing Pool Ball Set Pool Cloth Brush Plastic Triangle Cue Chalk Cue Stick Red Striker Red Puck Striker Felt Pad Blower Motor Hardware Kit Owner s Manual 03 Escalade Sports 6 For Customer Service Call -886-996-79 0 34 8 8 8 8 8 4 6 4 4 4 4 4 4 4 4 4 4 8

90 DAY LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of 90 days from the original purchase. WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PROD- UCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMAN- SHIP. WARRANTY PERFORMANCE: During the above 90 day warranty period, ESCALADESPORTS shall repair or replace with a comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept. -888-996-79 / Warranty Dept. Or Write us at: Escalade Sports, Inc. - P.O. Box 889, Evansville, IN 47706 Attn: Warranty Dept. Or E-mail us at: gameroom@escaladesports.com Other than shipping requirements no charge will be made for such repair or replacement of inwarranty Products. ESCALADE SPORTS strongly recommends that the Product is insured for value prior to mailing. WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM- ITED IN DURATION TO THE ABOVE 90 DAY PERIOD. ESCALADE SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES IN- CURRED BY THE CONSUMER OF ANY OTHER USE. Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above limitations or exclusions may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. 03 Escalade Sports 7 For Customer Service Call -886-996-79