R Tour Worksurfaces and Supports Table of Contents Topic Page COLUMN SUPPT SUPPT FRAME TIE BRACKET TO COUNTER Worksurface to Shelf Attachment 2 Worksurface to Counter Attachment Bracket 3 Worksurface Tied to End of Counter 4 Floating Worksurface Z Bracket Attachment Myfile Attachment to Worksurface 5 6 TO SHELF BRACKET NOTE: Use all the fasteners supplied with the supports. All floor supports have pilot holes for alignment. POST LEG LAMINATE PANEL SUPPT END OF COUNTER TO BRACKET T-27 TX POST LEG TAPERED LEG (SHOWN) POST LEG (SHOWN) TAPERED LEG TAPERED LEG MYFILE PEDESTAL FLOATING Z BRACKET COLUMN SUPPT 2008 Steelcase Inc. Grand Rapids, MI 4950 U.S.A. Printed in U.S.A. Page of 6
Worksurface to Shelf Attachment. Position two (2) worksurface to shelf brackets to be approximately from edge of worksurface being mounted (a). Attach worksurface to shelf bracket(s) to shelf using three (3) screws each (b). Top View a b 2. Position worksurface onto worksurface to shelf brackets (2a) and attach each bracket to worksurface using three (3) screws each (2b). TO SHELF BRACKET 2b SHELF 2-/4" NOTE: Position brackets from the edge of the worksurface. Distance between the two brackets will vary depending on the worksurface width. 2a A single worksurface can also be mounted to two (2) counters. b 2a NOTE: Use three (3) brackets for full length. Page 2 of 6
Worksurface to Counter Attachment Bracket. Position brackets to be approximately from the edge of worksurface being mounted (a). If possible, use supplied holes underneath counter for mounting the brackets and place brackets over holes and attach each bracket using two (2) /4-20 nuts and two (2) /4-20 screws (b). /4-20 NUT TIE BRACKET TO COUNTER b a Top View 2. Place worksurface onto brackets (2a) and attach each bracket to the worksurface using two (2) screws each (2b). COUNTER -5/6" 2b NOTE: Use three (3) brackets for full length. 2a /4-20 NUT A single worksurface can also be mounted to two (2) counters. TIE BRACKET TO COUNTER Page 3 of 6
Worksurface Tied to End of Counter. Remove each frame corner trim as shown. 2. Break each piece of trim in half along die cut. 3. Reposition both partial pieces of trim back on frame as shown. /2 FRAME CNER TRIM 4 FLAT HEAD TX DRIVE END OF COUNTER TO BRACKET 4. Position end of counter to worksurface bracket to end of counter and attach using two (2) screws. 3 FRAME CNER TRIM NOTE: Worksurface needs to be fully supported. This tie bracket is to be used as a tie to the counter, not a support. 5. Set worksurface onto end of counter to worksurface bracket and attach using two (2) screws. 2 DISCARD THIS PIECE 5 SAVE THIS PIECE Page 4 of 6
Floating Worksurface Z Bracket Attachment. The host table and the round worksurface must be supported by one () column base or two (2) post or tapered legs per the application guidelines. 2. The floating worksurface Z bracket is to be centered on the round worksurface and 8" maximum from the host table. POST TAPERED LEGS POST TAPERED LEGS POST TAPERED LEGS 36" ROUND MAX. POST TAPERED LEGS C L C L 36" ROUND MAX. Z BRACKET Z BRACKET Z BRACKET 8" MAX. 8" MAX. 8" MAX. 2 2 2 Page 5 of 6
Myfile Attachment to Worksurface. Fully extend drawer and push in on the side tabs on the suspension, as shown, to remove the drawer. 2. Place worksurface over the pedestal. Locate the worksurface flush to the side of the pedestal and flush to the rear of the pedestal as shown. Secure the worksurface to the pedestal with two (2) screws supplied. NOTE: Drilling /8" pilot holes will ease the attachment of the screws. 3. Reinstall drawer and level worksurface with glides provided on the bottom of the pedestal. 3 S 2 FLUSH FLUSH Page 6 of 6