Multi-Channel, Class D, 70 Watt Amplifier OWNER S MANUAL >> EA-AMP-12D-70A EA-AMP-8D-70A 12 CHANNEL 8 CHANNEL

Similar documents
ECA COMMERCIAL AMPLIFIER OWNER S MANUAL ECA-70MIXAMP V / 70V / 4Ω Amplifier ECA-70MIXAMP-1-60 OUTPUT LEVEL POWER MASTER MIC 1

Installation Manual. 45 Watt, Class D 12 Channel Amplifier EA-AMP-12D-45A

A Channel Amplifier

plifier D-501 otion Am Tactile M

INSTALLATION MANUAL EA-AMP-SUB-1D-500R EA-AMP-SUB-1D-500R

2BSST POWER AMPLIFIER OWNER S MANUAL

INSTALLATION MANUAL ECA-70VMINI-60W ECA-70VMINI-60W L VOLUME SPEAKER OUTPUTS 12VDC IN + L+ L- GND R+ R- S GND GND Tx Rx

REVAMP4100 Instruction manual

HTA125A/250A. Power Amplifiers. Installation & Use Manual

Big Bang. SpeakerCraft. BB1235 Owner s Manual. Power Amplifiers

IMPORTANT SAFETY INSTRUCTIONS

Model CC4041. CC Series Amplifier. Installation and Use Manual

M-300 Mono power amplifier User s guide

R-Series R235LS 2-Channel Power Amplifier with Local Source Switching

OWNER S MANUAL A

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Big Bang. B B O w n e r s M a n u a l. Power Amplifiers. SpeakerCraft BB2125 POWER ACTIVE PROTECTION L

Classic Series Public Address Amplifiers C10 & C20 Models

KLASIK NEAR FIELD ACTIVE STUDIO MONITOR

CLASS D STEREO AMPLIFIER 60 WPC. Model: APA102 User Manual

Model CC4052. CC Series Amplifier. Installation and Use Manual

4-Zone / 8-Channel Amplifier DPA-4.8. Instruction Manual 4 Z O N E 8 C H A N N E L A M P L I F I E R POWER ZONE DPA-4.8

SVS SoundPath Wireless Audio Adapter Owner s Manual

OWNER S MANUAL EVOLUTION SERIES POWERED SUBWOOFER

WX-1 & WX-3 OPERATING MANUAL AND USER GUIDE. Professional Power Amplifier. WX-1 and WX-3.indd :23:16

Classic Series Amplifiers C35, C60, & C100 Models

Dual Alarm Clock Radio with Digital Tuning NRC-174. Instruction Manual Please read carefully before use and keep for future reference.

REVAMP4120T Instruction manual

Classic Series Public Address Amplifiers C10 & C20 Models

1695T Black Magick. User Manual

AV30MX-2 Operation Manual

Safety Precautions. Important Safety Instructions

MODEL A1. PackLite TM POWER AMPLIFIER

REVAMP2250 Instruction manual

DA216S DISTRIBUTION AMPLIFIER

MIC MECHANIC 2. Ultra-Simple Battery-Powered Vocal Effects Stompbox with Echo, Reverb and Pitch Correction. User Manual

System Integration 2CH Amplifier

OWNER S MANUAL. Triple 8 and 10 in. Powered Subwoofers

PAM 1270 MULTI-ZONE AMPLIFIER OWNER S MANUAL WARRANTY & REPAIR

User Manual LMS-325 Line Monitor Speaker

Spider IV 15. Pilot s Handbook Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto 取扱説明書

Mini-Z. Manual. Model: ZA-21.

3400 Watt Stereo Power Amplifier

PREZONE1 Instruction manual

DPA-1.2. Instruction Manual. 2 Channel Amplifier with Auto A/B Selector DPA-1.2 DPA-1.2 POWER SERIAL # LINE INPUT SENSING SPEAKER B OUT

Carmen Ghia. Manual. Model: ZA-07.

AV25-2 User Manual. 1 Important safety instructions

HARMONY SINGER 2. Battery-Powered Vocal Effects Stompbox with Guitar-Controlled Harmony, Reverb and Tone. User Manual

Lanen True Diversity UHF Systems For electric and bass guitars: GB21 For Series 21 mics: UHF21. User Manual GB21 receiver/uhf21 transmitter

SPECIAL 6. 6-Watt Vacuum Tube Guitar Amplifier. User Manual

User Guide. Wideband 4-channel Auto Gain-Control Antenna Divider

R850MC. 4-Zone, 8-Channel Power Amplifier Installation Manual

Professional Tube Amplifier PRO-18 User Manual

Instruction Manual Please read carefully before use and keep for future reference.

1668RT Jupiter. User Manual

SAGA PRO SERIES STEREO POWER AMPLIFIER OPERATION MANUAL

Important Safety Information

Lanen Series 21 from Prodipe SB21 Lanen Instrument Mic. User Manual SB21 Lanen Sax / Brass / Percussion

EPA104/254. User Manual.

Z-LUX. Manual. Model: ZA-38.

arthur ART48 - YELLOW ACOUSTIC FIDELITY USER MANUAL Assembling instruction on ART48-L/Rmast manual

Audio Systems. Mono Amplifier with Subwoofer Crossover OWNER S MANUAL

A WORLD OF LISTENING WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Antidote. Manual. Model: ZA-35.

PagePac Plus AmpliCenter V A/V A Installation and Use

10 WATT GUITAR COMBO

WM-SYS3/WM-SYS3D/WM-SYS4/WM-SYS4D

Spider. Pilot s Handbook Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto 取扱説明書

EPA152/252/502. User Manual.

CR31. Companion. Instruction Manual

Utility Radio WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC

PagePac Plus AmpliCenter V A - (D300A) V A - (D100A) V (D40) Installation and Use

Spider Valve. Pilot s Guide Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto 取扱説明書

Important safety instructions

MAZ 18/MAZ 38. Manual. Model: ZA-8 / ZA-5.

w i t h T A B L E O F C O N T E N T S Safety Information 2 Certifications/Standards 3

875HT OWNER S MANUAL

A-16D A-Net Distributor

MIXER POWER AMPLIFIER BG-130

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH THANK YOU! DARK TERROR. Thank you for choosing Orange. You are now a member of the Legendary British Guitar Amplifier owners club!

Black Max Amplifier X300, X450, & X600 Models

Primare A33.2 Amplifier User Guide

RackAmp 250 AMPLIFIER MANUAL WARRANTY INFORMATION

OWNER S MANUAL CPS 1 / CPS 2 CONTRACTOR PRECISION SERIES

ENGLISH TERROR BASS 500/1000

Owner s Manual. MOON Series W5.3 SE. Stereo Power Amplifier

MC58 Eight Channel Power Amplifier

MC75 Tube Power Amplifier Owner s Manual

Dual Terror Owners Manual

i3speakers LX503 MK2 User Manual

ENGLISH THANK YOU! OR15. Thank you for choosing Orange. You are now a member of the Legendary British Guitar Amplifier owners club!

3.Avoid spilling liquids or allowing materials to enter the cabinet

CANARY AUDIO. Power Amplifier CA-309 OWNER S MANUAL. Handcrafted in California MADE IN USA

GOLD NOTE PA-1175 PA Stereo Power Amplifier. Stereo - Bridged Mono OWNER S MANUAL

DSR-3. Bedienungsanleitung User Guide

DT25 Guitar Amplifier Pilot s Guide Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto 取扱説明書

THE NEW FACE OF BASS PRO BASS SYSTEM U30, U60, U120. Owner s Manual

SB 15/230. Active Speaker Soundbar. Designed to Entertain. User Guide English

Transcription:

OWNE S MANUA >> Multi-Channel, Class D, 70 Watt Amplifier EA-AMP-12D-70A 12 CHANNE EA-AMP-8D-70A 8 CHANNE

IMPOTANT SAFETY INSTUCTIONS WANING: To reduce the risk of fire or electric shock, do not expose this apparatus in or near rain or moisture. 1. ead the following instructions carefully. 2. Keep manual for future reference. 3. Heed all warnings. 4. Follow all instructions in this manual. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install according to manufacturer s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9. Do not override the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades - one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plug, convenience receptacles, and the point where it exits from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment. 15. efer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 16. To completely disconnect this equipment from the AC mains, disconnect the power supply cord plug from the AC receptacle. CAUTION CAUTION: TO EDUCE THE ISK OF EECTICA SHOCK, DO NOT EMOVE COVE. NO USE SEVICEABE PATS INSIDE. EFE SEVICING TO QUAIFIED SEVICE PESONNE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. pg.3 2015 Episode

WECOME TO EPISODE Episode is one of the most highly-regarded brands of audio products available today. We appreciate your business, and we stand committed to providing our customers with the highest degree of quality and service in the industry These Episode Amplifiers are built on the latest digital technology and deliver efficient, clean power to every room. Each model is designed to produce the subtle details of music, while having the flexibility to meet a variety of installations. For the best sound quality, use Episode Speakers to complete the system. FEATUES DUABE AUDIOPHIE DESIGN These Episode Amplifiers use the latest digital technology to deliver cool-running performance from a compact, reliable package. Plus, they feature superior quality components for outstanding sound quality and are up to 90% more efficient than conventional analog designs. MUTIPE STAGES OF POTECTION Each pair of channels (or Zone) is individually protected with an operation mode indicated by bi-color EDs on the front of the amplifier. These enable simple troubleshooting. If the circuitry determines that a channel must be shut down for protection due to a short, only the channels that are affected will be turned off. The other zones will continue to play. GOBA A & B AND DIECT S A dedicated input can be assigned to a pair of channels via the channel ine In connection. Each pair of channels can also be configured to play common signals from the global input. When using the global connections, odd-numbered channels will receive the right channel, and the even-numbered channels will receive the left channel. This is further indicated by the color of the channel ine In jacks (odd numbers have white jacks and even numbers have red jacks). A 3 position switch is available for each channel pair to choose between the line-in and the 2 Global-Inputs. This provides unparalleled flexibility that is needed for today s demanding custom audio installations. INDIVIDUA CHANNE AND GAIN ADJUSTMENTS Each pair of channels has its own level adjustment which adjusts the maximum output. This allows the output of to be perfectly matched to its area. It can also serve to provide a limit on how loud each speaker may be allowed to play. Be sure set the volume at a level that does not clip or cause distortion when the volume is at the maximum level. This can cause damage to the speakers and the amplifier. INSTAATION-FIENDY CONNECTIONS Each pair of speakers feature a removable speaker wire connector that accommodates up to 14 gauge stranded speaker wire. The power cord is removable as well, facilitating fast and simple installations. The Global Inputs, oop Output, and individual Channel Inputs are all high-quality CA connectors. BIDGING The power output of adjacent channels can be combined to provide extra power when needed in certain areas. This is easily accomplished by flipping a single switch. Maintain an 8 ohm minimum when using bridge mode. ACK-MOUNTABE Each Episode amplifier includes an accessory package of rack ears that may be attached to the amplifier. The amplifier feet can be easily removed for clean rack mounting. The amplifier chassis and rack ears are NOT designed to support anything other than the amplifier. DO NOT stack components on top of the amplifier, as it could damage the amplifier s chassis. POWE MODE Power state can be toggled using the front Power Button, 12V input, or Audio Sensing. The method for power toggle is set by using the Power Mode Switch on the rear of the amplifier. See Power Mode Switch under ear Channel Features for information on the operation of each mode. Note: The front panel power button is inoperative when the 12V Trigger or Audio Sense power modes are selected. pg.4

EA-AMP-12D-70 1 2 3 4 5 6 7 8 9 10 11 12 EA PANE FEATUES (12D and 8D) 1. GOBA Easily amplify outputs from any stereo source across any/all channels 2. OOP OUT Allows global inputs to be sent to other amplifiers 3. GAIN CONTO Allows independent gain for each pair of inputs 4. BIDGED SWITCH Easily couple two channels together for increased power NOTE: 8-ohm minimum when using bridge mode 5. INE S Individual channel inputs for use with multi-channel preamps/ or dedicated sources pg.5 2015 Episode

EA-AMP-8D-70 1 2 3 4 5 6 7 8 9 10 11 12 6. SWITCH Choose between global inputs and individual inputs for each channel 7. SPEAKE S 8. MASTE POWE SWITCH Disables power to the amplifier 9. POWE MODE SWITCH Sets the amplifiers power mode: On Turns ON / OFF via front power button 12V Turns on when +12V is received at Trigger input AUDIO - Turns on when a minimal amount of audio signal is received at the audio inputs and will go into standby after 18 minutes of no audio signal. Note: The front panel power button is inoperative when the 12V Trigger or Audio Sense power modes are selected. 10. 12V TIGGE IN/OUT Turns amplifier on when 12v dc is applied and power mode switch is set to 12v. This 12v signal is regenerated to the 12v out for triggering additional amplifiers. Note: the front panel power button is inoperative when the 12v trigger or audio sense power modes are selected. 11. FUSE OCATION pg.6 12. POWE CONNECTO

POSITIONING YOU EPISODE AMPIFIE Episode amplifiers are designed to help deliver a great audio experience that makes your music come alive for years to come. However, where you place the amplifier can have a large effect on the performance that you receive and the life of the unit. Be sure that the unit is in a well-ventilated area that provides adequate cooling. Do not block the cooling vents located on both sides of the unit. Do not place the unit on carpeting or any similar material. Do not install the unit near a source of heat, or in an extremely humid or wet location. If your installation lacks good air flow (such as solid cabinet doors or wall-mounted racks), it may be necessary to create ventilation to allow outside air into the space. Allow a minimum of 5 of free air space above the unit. Allow a minimum of 3 of free air space on either side of the unit. (Does not apply to rack mounting). Minimum of 5" of free air space above Minimum of 2" of depth behind unit to accommodate cables and connectors Minimum of 3" free air space on each side INSTAATION GETTING CONNECTED CAUTION: All connections and switching must be done with the amplifier s power switch positioned to Off. Connect the power cord last to ensure that the amplifier is off during all of your connections and set up. S For line level connections, use high-quality CA cables that feature low impedance, shielding and high-quality connectors. SPEAKE S Use 14-18 gauge stranded two-conductor loudspeaker wire for all high level connections. At each loudspeaker-level connection, ensure that at least 2 inches of each conductor are separated. Strip away 1/4 inch of insulation from each conductor. Connect the appropriate conductor to the speaker connection, observing correct polarity. pg.7 2015 Episode

VEIFYING PHASE When proper polarity is not maintained, the speakers play at the opposite time from each other, or out of phase. The result is audio with lack of bass and vocals that sound thin or distant. If during or after calibrating your receiver you suspect the sound is not right and you cannot see any markings on the wire to verify polarity is correct, try this simple test: 1. Sit in the normal listening position for the system. 2. Play some music with your receiver set to Mono. isten to the music and observe the audio. - Does the bass sound full and even with the other audio? - Do the vocals sound centered and even in volume? If any of the answers are YES, follow steps 3 and 4. 3. Turn off your receiver and reverse the connections for one of the speakers. 4. epeat your test at the same volume level. When the sound has the loudest and best sounding bass, and vocals are centered and clear, your connections are correct and in-phase. OOP S Any source connected to the ine In Input can be sent to other components or amplifiers by connecting them to the Global oop output connectors. pg.8

INSTAATION SETUP AND OPTIONS SEECTION CAUTION: Only change switch positions when the amplifier is turned off.each channel is capable of delivering the sources from a dedicated ine-in or the Global-Inputs by changing the ine-in/ Global In switch. POWE CONNECTION Plug the supplied power cord into the amplifier and to a polarized wall outlet or appropriate surge protector. CAUTION: DO NOT plug the amplifier s power cord into a switched outlet, as is featured on some Surround eceivers. If you wish to have the amplifier turn on when the eceiver is powered up, use the 12V trigger jack or Audio Sense mode. BIDGING CHANNES There are situations when you may wish to combine two channels into one through a process known as bridging. The output of the two combined channels can then be used to power one speaker. Switch in bridged mode To Bridge Two Adjacent Channels: 1. emove Power from the amplifier. 2. Set the channel switch to BIDGED/MONO. 3. Connect the (+) POSITIVE lead of the speaker to the (+)POSITIVE connection of the EVEN numbered channel. 4. Connect the (-) NEGATIVE lead of the speaker to the (+) POSITIVE connection of the ODD numbered channel. 5. Connect the output from the source to the INE IN of the EVEN numbered channel. Note: DO NOT connect more than one speaker to the outputs of the bridged channel. All input selection and volume settings for bridged channels will be controlled by the ED channel. Maintain an 8 ohm minimum when using bridge mode. Source Output OPEATION Speaker (-) Negative Speaker (+) Positive POWE SWITCH/ ED The Power switch on the front panel of the amplifier will turn off the amplifier when the Power Mode Switch is set to ON. BUE Amplifier is ON ED Amplifier is in STANDBY efer to the Power Mode section for further information. ZONE ED INDICATOS When lit, the EDs on the front panel indicate the amplifiers operating state. Each channel has one bi-color ED, for each zone. BUE Amplifier is ON and functioning properly ED Amplifier is ON and is not functioning properly, check for possible short at Speaker Output OFF (When Power ED is BUE) A channel is not functioning and may require service. EVE ADJUSTMENT The level adjustments on the back panel of the amplifier can be used to easily adjust the level of each channel pair. One great use for this feature is to limit the volume level in an area, such as a child s room or guest area. Be sure set the volume at a level that does not clip or cause distortion when the volume is at the maximum level. This can cause damage to the speakers and the amplifier. pg.9 2015 Episode

EPISODE MUTI-OOM INSTAATION ECEIVE CD PAYE DVD AUX CD IPOD DVD PAYE OOM 1 OOM 2 OOM 3 OOM 4 OOM 5 OOM 6 GOBA A GOBA B SONOS pg.10

EPISODE MUTI-ZONE INSTAATION CD PAYE DVD PAYE TUNE IPOD CD DVD TUNE AUX AUDIO MATIX SWITCHE ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 pg.11 2015 Episode

EPISODE HOME THEATE/MUTI-OOM INSTAATION HOME THEATE ECEIVE EFT CENTE SPEAKE S IGHT EA EFT EA IGHT SUBWOOFE MUTIOOM VC DVD CD VC DVD PAYE CD PAYE OOM 1 OOM 2 OOM 3 OOM 4 OOM 5 OOM 6 pg.12

TOUBESHOOTING No audio from any channel. No audio from one or more channels. No audio from one channel or one zone only. Hum or buzzing sound is heard. Amplifier will not turn on. Front Power Button Inoperative Power cable to the amplifier is incorrectly connected or plugged into an outlet that does not have power. Check connections and verify power on the outlet. Audio cable to the source component is not connected properly, connected to incorrect BUS input or the cable is defective. Check connections or replace cable with one that has been verified as good. The Input Selection switches are set incorrectly. efer to instructions for correct settings. Audio cable to the source component is not connected properly or the cable is defective. Check connections or replace cable with one that has been verified as good. The Input Selection switch is positioned incorrectly. efer to installation instructions for proper settings. The Bridging switch is positioned incorrectly. efer to installation instructions for proper settings. Check the connections of the speaker wire at both the speaker and amplifier. Check the front panel ED for the zone that is not working. If it is red, you may have a short on either one of the speaker wires for that zone. Check wires and speaker connections for shorts. The level adjustment on the channel is turned down. Turn it slowly to the right to raise the volume. Test the bad channel by connecting it to a speaker that you know works. Audio cable to the source component is not connected properly or the cable is defective. Check connections or replace cable with one that has been verified as good. The Input Selection switch is positioned incorrectly. efer to installation instructions for proper settings. The Bridging switch is positioned incorrectly. efer to installation instructions for proper settings. Check the connections of the speaker wire at both the speaker and amplifier. Check CA input cables by removing them one at time (powering down the amplifier before disconnecting) and checking to see if a connection or cable is to blame. The amplifier must be plugged into a live outlet. The power switch on the back panel must be on. Ensure 12V is present if using the trigger input. Set the Power Mode Switch to ON. For Technical Support, call 1.866.838.5052 pg.13 2015 Episode

SPECIFICATIONS Continuous Power Output All channels driven Bridged Power Output All channels driven Input Sensitivity Input Impedance S/N ratio Frequency esponse Distortion (Unbridged) Distortion (Bridged) Dimensions Weight Certification 50 watts MS at 8 ohms 70 watts MS at 4 ohms 140 Watts per channel MS at 8 ohms Note: Maintain 8 ohm minimum when using bridge mode 500mV 20,000 ohms 95 db 20 Hz to 20 khz 0.1% THD 20 Hz-20 khz 0.1% THD 20 Hz-20 khz 17 w x 4 h (including feet) x 13 deep 8 ch: 25.3lbs / 12 ch: 32lbs Meets FCC Part 15, ET isted and tested under U/EN60065 *All specifications are subject to change without notice WAANTY 2-Year imited Warranty Episode Amplifier Products have a 2-Year imited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (A). pg.14

170301-1030 2017 Episode