ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES

ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR HIGH POWER CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT ASSEMBLY INSTRUCTIONS SECTION 3 CONTACT INSTALLATION AND REMOVAL INSTRUCTIONS SECTION 4 MODULE INSTALLATION AND REMOVAL INSTRUCTIONS SECTION 5 ITA CABLE ASSEMBLY INSTRUCTIONS SECTION 6 HIGH POWER ACCESSORIES SECTION 7 CROSS REFERENCE TABLES APPENDIX PRODUCT PERFORMANCE SPECIFICATIONS Please note that any printed or downloaded User Manuals or Procedure Sheets may not reflect the most current revisions. The information contained in these materials is subject to change. For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 1 HIGH POWER RECEIVER CONTACT ASSEMBLY PART # 610 149 101, 610 150 101 FRONT PLATE Wire Cutter Jacket Stripper Pneumatic Crimp Tool Kit, Part # 910 102 116, (Figure A) includes: High Power Pneumatic Crimper High Power Contact Locator High Power Contact Die Set Point Micrometer Heat Gun CRIMP TOOL SETUP 1. Disconnect airline. 2. Install locator into locator cavity (Figure B). 3. Install die set into pneumatic crimper (Figure B). 4. Ensure front plate is installed on crimper (Figure A). 5. Re-connect airline. Figure A. Pneumatic crimper. HIGH POWER PNEUMATIC CRIMPER HIGH POWER CONTACT LOCATOR HIGH POWER CONTACT DIE SET Figure B. Exploded view of pneumatic crimper. INSPECTION HOLE ASSEMBLY INSTRUCTIONS 1. Cut wire to length. 2. Strip wire 0.75" (19.05 mm). Figure C1. 610 149 101 contact. Figure C2. 610 150 101 contact. 3. Carefully insert wire into the wire end of the contact. NOTE: Be careful not to disturb the natural lay of the individual wire strands, this could make it difficult to insert the strands into the contact. 4. Place the contact into the crimper cavity until it completely bottoms out against the end of the locator. 5. Depress button to crimp and then remove the crimped wire and contact from the crimp cavity (Figure C). 6. Inspect the location of crimp indentions. Indentions should be located between the wire end of the crimp barrel and the wire inspection hole. The wire should be visible in the inspection hole (Figure C). 7. Use a point micrometer to measure the crimp height across the crimp indentions. Measure across the crimp indentions, rotate the contact 90 and measure across remaining crimp indentions. The measurement should be 0.279" ± 0.005" [7.087 ± 0.127 mm] (Figure D). 8. Slide a 2" piece of Ø0.5" shrink tubing over the contact up to the first shoulder from the wire end of the contact covering the inspection hole and shrink in place with heat gun (Figure E). NOTE: Contact tested and designed for specific use with Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. If using a wire other than prescribed, reference 5.3.5 Machined Contacts - CMA buildup of the IPC/WHMA-A-620A standard. NOTE: Recommended CMA range for this contact falls between 63,206 and 66,499 with a max conductor Ø of.340" [8.636 mm] and a min conductor Ø of.315" [8.001 mm]. To calculate CMA please reference Figure F. Figure D. Measuring crimp. Figure E. Applied shrink tubing. Stranded Wire AWG D Number of Strands Metric Dimensions CMA = D 2 x N x 1550.003 CMA = Circular Mil Area D = Diameter of Single Strand in millimeters N = Number of Strands U.S. Customary Dimensions CMA = D 2 x N CMA = Circular Mil Area D = Diameter of Single Strand in mils N = Number of Strands Figure F. Calculate circular mil area. D 1-1 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 3 HIGH POWER 90 SERIES RECEIVER CONTACT INSTALLATION AND REMOVAL PART # 510 104 307 Phillips Head Screwdriver High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 In/Lbs Torque Driver CONTACT INSTALLATION INSTRUCTIONS 1. Assemble the contact to the respective wire. NOTE: Contact tested and designed for specific use with 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. NOTE: For more information concerning the contact assembly process, please see contact assembly instructions in Section 1 of this User s Manual. 2. Insert the assembled contact into the back (wiring side) of the assembled module. Once in place, pull the wire slightly to ensure that the contact is fully seated. 3. Install strain relief plate and secure wires to strain relief. NOTE: In all High Power contact applications, VPC highly recommends the use of a strain relief plate. CONTACT REMOVAL INSTRUCTIONS 1. Remove the module from the receiver frame. NOTE: For more information concerning the process of removing the module from the receiver frame, see module installation and removal instructions in Section 4 of this User s Manual. Figure A. Separating the module. 2. Use a Phillips head screwdriver to remove the screws located at the top and bottom of the module. 3. Grasp the module halves and apply force in opposite directions, rocking the ends of the module while slightly pulling the top of the module away from the mating bottom section, until separated (Figure A). RETAINING RING TAB 4. Place the High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 (Figure B), over the contact to be removed/ replaced. Use care to keep the tool perpendicular to the surface of the module, otherwise the tool or contact could be damaged. Rotate the tool slightly while pushing it into the counter bore on the mating side of the module. EXTRACTION TOOL PART # 910 112 129 A DETAIL A 5. Once the extraction tool is seated and the retaining tabs on the retaining ring are compressed (Figure B), push the tool into the module. The contact will be pushed out of the rear of the module. DO NOT PUSH THE TOOL INTO THE MODULE UNTIL THE TIP OF THE EXTRACTION TOOL HAS FULLY SEATED INTO THE MODULE AND COMPRESSED THE RETAINING RING TABS ON THE CONTACT. HIGH POWER RECEIVER CONTACT Figure B. Fully seat extraction tool before depressing. 6. If necessary, replace the module cap using both hands to push the separated halves together. Replace and tighten the module retaining screws to a maximum torque of 1.5 in-lbs [0.17 Nm]. 3-1 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 3 HIGH POWER icon/i1 RECEIVER CONTACT INSTALLATION AND REMOVAL PART # 510 160 124 Flat Head Screwdriver Phillips Head Screwdriver High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 In/Lbs Torque Driver CONTACT INSTALLATION/LOADING INSTRUCTIONS 1. Assemble the contact to the respective wire. NOTE: Contact tested and designed for specific use with 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. NOTE: For more information concerning the contact assembly process, please see contact assembly instructions in Section 1 of this User s Manual. 2. Ensure empty modules are secure in receiver frame. Insert the assembled contact into the back (wiring side) of the assembled module. Once in place, pull the wire slightly to ensure that the contact is fully seated. NOTE: For more information concerning the module installation process, please see icon module installation and removal instructions in Section 4 of this User s Manual. 3. If loading an icon frame, repeat steps 1 and 2 for module A, loading High Power contacts in positions 3 and 4 only (All TriPaddle positions may be used). 4. Install strain relief plate and secure wires to strain relief. NOTE: In all High Power contact applications, VPC highly recommends the use of a strain relief plate. CONTACT REMOVAL INSTRUCTIONS 1. Remove the module from the receiver frame. NOTE: For more information concerning the process of removing the module from the receiver frame, see module installation and removal instructions in Section 4 of this User s Manual. Figure A. Correctly loaded receiver contacts in i1. A or TOP POSITION B or BOTTOM POSITION Figure B. Correctly loaded receiver contacts in icon. 2. Use a Phillips head screwdriver to remove the screws located at the top and bottom of the module. 3. Grasp the module halves and apply force in opposite directions, rocking the ends of the module while slightly pulling the top of the module away from the mating bottom section, until separated. You may pry at the machined slot on the module using a flat head screwdriver to assist in opening the module. Be sure to open both sides of the module simultaneously or contacts could be damaged. 4. Place the High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 (Figure C), over the contact to be removed/ replaced. Use care to keep the tool perpendicular to the surface of the module, otherwise the tool or contact could be damaged. Rotate the tool slightly while pushing it into the counter bore on the mating side of the module. 5. Once the extraction tool is seated and the retaining tabs on the retaining ring are compressed (Figure C), push the tool into the module. The contact will be pushed out of the rear of the module. DO NOT PUSH THE TOOL INTO THE MODULE UNTIL THE TIP OF THE EXTRACTION TOOL HAS FULLY SEATED INTO THE MODULE AND COMPRESSED THE RETAINING RING TABS ON THE CONTACT. RETAINING RING TAB EXTRACTION TOOL PART # 910 112 129 A DETAIL A 6. If necessary, replace the module cap using both hands to push the separated halves together. Replace and tighten the module retaining screws to a maximum torque of 1.5 in-lbs [0.17 Nm]. HIGH POWER RECEIVER CONTACT Figure C. Fully seat extraction tool before depressing. 3-2 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 3 HIGH POWER 90 SERIES ITA CONTACT INSTALLATION AND REMOVAL PART # 510 108 281 Phillips Head Screwdriver High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 In/Lbs Torque Driver CONTACT INSTALLATION INSTRUCTIONS 1. Assemble the contact to the respective wire. NOTE: Contact tested and designed for specific use with 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. NOTE: For more information concerning the contact assembly process, please see contact assembly instructions in Section 2 of this User s Manual. 2. Insert the assembled contact into the back (wiring side) of the assembled module. Once in place, pull the wire slightly to ensure that the contact is fully seated. 3. Install strain relief plate and secure wires to strain relief. NOTE: In all High Power contact applications, VPC highly recommends the use of a strain relief plate. CONTACT REMOVAL INSTRUCTIONS 1. Remove the module from the ITA frame. NOTE: Prior to extracting contacts, wire must be untied from the strain relief. NOTE: For more information concerning the process of removing the module from the ITA frame, see module installation and removal instructions in Section 4 of this User s Manual. Figure A. Separating the module. 2. Use a Phillips head screwdriver to remove the screws located at the top and bottom of the module. 3. Grasp the module halves and apply force in opposite directions, rocking the ends of the module while slightly pulling the top of the module away from the mating bottom section, until separated. Be sure to open both sides of the module simultaneously or contacts could be damaged (Figure A). 4. Place the High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 (Figure B), over the contact to be removed/ replaced. Use care to keep the tool perpendicular to the surface of the module, otherwise the tool or contact could be damaged. Rotate the tool slightly while pushing it into the counter bore on the mating side of the module. EXTRACTION TOOL PART # 910 112 129 RETAINING RING TAB A DETAIL A 5. Once the extraction tool is seated and the retaining tabs on the retaining ring are compressed (Figure B), push the tool into the module. The contact will be pushed out of the rear of the module. DO NOT PUSH THE TOOL INTO THE MODULE UNTIL THE TIP OF THE EXTRACTION TOOL HAS FULLY SEATED INTO THE MODULE AND COMPRESSED THE RETAINING RING TABS ON THE CONTACT. HIGH POWER ITA CONTACT Figure B. Fully seat extraction tool before depressing. 6. If necessary, replace the module cap using both hands to push the separated halves together. Replace and tighten the module retaining screws to a maximum torque of 1.5 in-lbs [0.17 Nm]. 3-3 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 3 HIGH POWER icon/i1 ITA CONTACT INSTALLATION AND REMOVAL PART # 510 161 124 Flat Head Screwdriver Phillips Head Screwdriver High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 In/Lbs Torque Driver CONTACT INSTALLATION/LOADING INSTRUCTIONS 1. Assemble the contact to the respective wire. NOTE: Contact tested and designed for specific use with 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. NOTE: For more information concerning the contact assembly process, please see contact assembly instructions in Section 2 of this User s Manual. 2. Ensure empty modules are secure in ITA frame. Insert the assembled contact into the back (wiring side) of the assembled module. Once in place, pull the wire slightly to ensure that the contact is fully seated. NOTE: For more information concerning the module installation process, please see icon/i1 module installation and removal instructions in Section 4 of this User s Manual. 3. If loading an icon frame, repeat steps 1 and 2 for module A, loading High Power contacts in positions 3 and 4 only (All TriPaddle positions may be used). CONTACT REMOVAL INSTRUCTIONS 1. Remove the module from the ITA frame. NOTE: For more information concerning the process of removing the module from the ITA frame, see module installation and removal instructions in Section 4 of this User s Manual. 2. Use a Phillips head screwdriver to remove the screws located at the top and bottom of the module. 3. Grasp the module halves and apply force in opposite directions, rocking the ends of the module while slightly pulling the top of the module away from the mating bottom section, until separated. You may pry at the machined slot on the module using a flat head screwdriver to assist in opening the module. Be sure to open both sides of the module simultaneously or contacts could be damaged. 4. Place the High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 (Figure A), over the contact to be removed/replaced. Use care to keep the tool perpendicular to the surface of the module, otherwise the tool or contact could be damaged. Rotate the tool slightly while pushing it into the counter bore on the mating side of the module. 5. Once the extraction tool is seated and the retaining tabs on the retaining ring are compressed, push the tool into the module (Figure B). The contact will be pushed out of the rear of the module. Figure A. Correctly loaded ITA contacts in i1. A or TOP POSITION B or BOTTOM POSITION Figure B. Correctly loaded ITA contacts in icon. RETAINING RING TAB EXTRACTION TOOL PART # 910 112 129 A DETAIL A DO NOT PUSH THE TOOL INTO THE MODULE UNTIL THE TIP OF THE EXTRACTION TOOL HAS FULLY SEATED INTO THE MODULE AND COMPRESSED THE RETAINING RING TABS ON THE CONTACT. 6. If necessary, replace the module cap using both hands to push the separated halves together. Replace and tighten the module retaining screws to a maximum torque of 1.5 in-lbs [0.17 Nm]. HIGH POWER ITA CONTACT Figure B. Fully seat extraction tool before depressing. 3-4 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 4 HIGH POWER STANDARD/90 SERIES MODULE INSTALLATION AND REMOVAL 3 / 32 Allen Wrench In-lbs Torque Driver INSTALLATION INSTRUCTIONS 1. Place the module in the receiver or ITA until the upper and lower module screws touch the mating holes in the inner frame. Ensure that Position 1 is located at the top for systems in which the modules are oriented vertically or to the left for systems in which the modules are oriented horizontally. 2. Using a 3 / 32 Allen wrench, tighten the top screw (4-40 x 5 / 8 captive screw for the receiver module and 4-40 x 9 / 16 captive screw for ITA module)1 to 2 full revolutions, while pushing lightly against the face of the module. 3. Maintain this pressure while tightening the bottom screw 1 to 2 full revolutions. 4. Repeat this sequence until the module is seated. Tighten screws to a maximum torque of 4 in-lbs [0.45 Nm]. REMOVAL INSTRUCTIONS 1. To remove, loosen the top screw (4-40 x 5 / 8 captive screw for the receiver module and 4-40 x 9 / 16 captive screw for ITA module) 1 to 2 full revolutions. Loosen bottom screw 1 to 2 full revolutions. Figure A. Receiver Module. 2. Repeat this sequence until the module is separated from the receiver or ITA. NOTE: For optimum performance and system longevity, distribute the contact load evenly throughout the module. Figure B. ITA Module. 4-1 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 4 HIGH POWER icon/i1 MODULE INSTALLATION AND REMOVAL Phillips Head Screwdriver In-lbs Torque Driver INSTALLATION INSTRUCTIONS NOTE: The receiver strain relief plate or the ITA cover may need to be removed prior to installing or removing an icon module. Please refer to the appropriate User s Manual for instructions on how to perform these steps. 1. Place the module in the receiver or ITA until the upper and lower module screws touch the mating holes in the inner frame. Install modules such that Position 1 is located at the top of the ITA/ receiver frame. 2. Using a Phillips head screwdriver, tighten the top screw 1 to 2 full revolutions, while pushing lightly against the face of the module. 3. Maintain this pressure while tightening the bottom screw 1 to 2 full revolutions. 4. Repeat this sequence until the module is seated. Tighten screws to a maximum torque of 1.5 in-lbs [0.17 Nm]. A or TOP POSITION B or BOTTOM POSITION Figure A. Receiver Module. REMOVAL INSTRUCTIONS 1. To remove, loosen the top screw 1 to 2 full revolutions. Loosen bottom screw 1 to 2 full revolutions. 2. Repeat this sequence until the module is separated from the receiver or ITA. NOTE: For optimum performance and system longevity, distribute the contact load evenly throughout the module. A or TOP POSITION B or BOTTOM POSITION Figure B. ITA Module. 4-2 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 5 Flat Head Screwdriver Phillips Head Screwdriver High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 Heat Gun In-lbs Torque Driver HIGH POWER icon ITA CABLE ASSEMBLY PART # 410 123 122 BACK SHELL REMOVAL INSTRUCTIONS 1. Turn engagement knob in counterclockwise rotation to remove the plastic cover on the front of the ITA Figure A. 2. Unscrew the ITA cover chain from the ITA 3. Remove engagement knob and screw [Figure A]. 4. Remove 4 flat head screws from the positions shown [Figure B]. 5. Remove the flat head screw from the position shown and slide off the back shell assembly [Figure C]. Figure B. 6. Remove 2 flat head screws from the positions shown [Figure D]. 7. Slide off the U-shaped cable clamp assemnly [Figure E]. 8. Uncrew the 2 phillips head screws attached to the strain relief clamp to remove the clamp [Figure F]. NOTE: The cable clamp exit diameter is 1.55". Completed wire bundle should not exceed this dimension. Figure C. Figure D. Figure E. Figure F. 5-1 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 5 Flat Head Screwdriver Phillips Head Screwdriver 3 / 32 Allen Wrench High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 Heat Gun In-lbs Torque Driver HIGH POWER icon ITA CABLE ASSEMBLY PART # 410 123 106, 410 123 116, AND 410 123 122 CONTACT INSTALLATION INSTRUCTIONS NOTE: The ITA backshell must be removed prior to installing an icon module. Please refer to the icon User s Manual for instructions on how to perform this step. 1. Assemble the contact to the respective wire. NOTE: Contact tested and designed for specific use with 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. NOTE: For more information concerning the contact assembly process, please see contact assembly instructions in Section 2 of this User s Manual. A or TOP POSITION B or BOTTOM POSITION 2. Ensure empty modules are secure in ITA frame. 3. Insert the assembled contacts into the back (wiring side) of module A, in positions 3 and 4 only for 410123106 and 410123116; once in place, pull the wire slightly to ensure that the contact is fully seated. For 410123122 all High Power positions may be used. NOTE: For more information concerning the module installation process please see module installation and removal instructions in Section 4 of this User s Manual. 4. Insert TriPaddle contacts into the back (wiring side) of module A ; once in place, pull the wire slightly to ensure that the contact is fully seated (All TriPaddle positions may be used). Figure A. Fully loaded ITA. Figure B. Route wires around engagement post. 5. Repeat steps 3 and 4 for module B contact loading, except that module B can be loaded in all four positions of the module (Figure A). 6. Route wires down both sides of engagement post (Figure B). NOTE: Consult VPC for more information on the use of wire other than recommended. NOTE: The cable clamp exit diameter is 1.55". Completed wire bundle should not exceed this dimension. 5-2 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 5 Flat Head Screwdriver Phillips Head Screwdriver 3 / 32 Allen Wrench High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 Heat Gun In-lbs Torque Driver (optional) HIGH POWER icon ITA CABLE ASSEMBLY PART # 410 123 106, 410 123 116, AND 410 123 122 CONTACT INSTALLATION INSTRUCTIONS NOTE: The ITA backshell must be removed prior to installing an icon module. Please refer to the icon User s Manual for instructions on how to perform this step. Figure C. 7. If applicable, install protective sleeving at this time. Apply protective sleeving approximately 1" down from bottom of ITA frame. (Figure D). 8. Slide 4" shrink tubing up into cable clamp area as far as possible, covering lacing. Shrink into place with heat gun (Figure E). 9. Place U-shaped cable clamp over wire bundle and screw into rear of ITA frame using a 3 / 32 Allen wrench, taking care not to pinch wires in cable clamp (Figure F). Figure D. Applied protective sleeving. 10. Install cable clamp strain relief using Phillips-head screwdriver. 11. Slide cover onto ITA frame. Secure top captive screw first, then tighten the remaining four side screws into place using a Phillips-head screwdriver. Tighten screws to a maximum torque of 1.5 in-lbs [0.17 Nm] (Figure G). 12. Re-install engagement handle assembly, noting orientation of handle to ensure correct engagement clocking using a Phillips-head screwdriver. Tighten screw to a maximum torque of 2.5 in-lbs [0.28 Nm] (Figure H). Figure E. Applied shrink tube. NOTE: Consult VPC for more information on the use of wire other than recommended. NOTE: The cable clamp exit diameter is 1.55". Completed wire bundle should not exceed this dimension. POSITIONS 1 & 2 IN THE TOP MODULE CANNOT BE USED WITH 2 AWG WIRE EXCEPT ON 410 123 122 [FIGURE C]. Figure F. Attached U-shaped cable clamp. Figure G. Slide cover on ITA frame Figure H. Re-install engagement handle. 5-3 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 5 HIGH POWER i1 ITA CABLE ASSEMBLY PART # 410 128 103 Phillips Head Screwdriver High Power Receiver/ITA Contact Extraction Tool, Part # 910 112 129 Heat Gun In-lbs Torque Driver CONTACT INSTALLATION INSTRUCTIONS NOTE: The ITA backshell must be removed prior to installing an icon module. Please refer to the i1 User s Manual for instructions on how to perform this step. 1. Assemble the contact to the respective wire. NOTE: Contact tested and designed for specific use with 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. NOTE: For more information concerning the contact assembly process, please see contact assembly instructions in Section 2 of this User s Manual. 2. Ensure empty module is secure in ITA frame. Feed wire through cable clamp housing (uninstalled). Insert the assembled High Power and TriPaddle contacts into the back (wiring side) of module; once in place, pull the wire slightly to ensure that the contact is fully seated (Figure A). NOTE: For more information concerning the module installation process please see module installation and removal instructions in Section 4 of this User s Manual. Figure A. Route wire through cable clamp housing. 3. If applicable, install protective sleeving at this time. Apply protective sleeving approximately 1" below exit of cable clamp when in installed position. Slide 4" shrink tubing up into cable clamp area as far as possible, covering lacing. Shrink into place with heat gun (Figure B). 4. Slide cable clamp housing up length of wire and secure to bottom of ITA using Phillips head captive screws (Figure C). 5. Install and tighten cable clamp strain relief in place until wires/bundle is secure (Figure D). 6. Slide engagement housing over ITA frame/housing and secure in place by tightening the 4 Phillips head captive screws at the corners of the housing to a maximum torque of 1.5 in-lbs [0.17 Nm] (Figure E). Figure B. Apply sleeving and shrink tubing. NOTE: Consult VPC for more information on the use of wire other than recommended. NOTE: The cable clamp exit diameter is 1.26". Completed wire bundle should not exceed this dimension. Figure C. Attach cable clamp housing. Figure D. Attach strain relief cable clamp. Figure E. Attach engagement housing. 5-4 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 6 HIGH POWER ACCESSORIES PART # 510 109 549, AND 510 109 572 Phillips Head Screwdriver ASSEMBLY INSTRUCTIONS 90 SERIES 1. Use a Phillips-head screwdriver to fasten the strain relief to the 90 Series receiver module on the side of the receiver module as shown in (Figure A). 2. Wires should be restrained with slots in strain relief and be in line with the axis of its contact cavity. Twelve wire ties are included with the strain relief. ASSEMBLY INSTRUCTIONS ICON/I1 1. Use a Phillips-head screwdriver to fasten the strain relief to the icon/i1 receiver module on the sides of the receiver module as shown in (Figure B). 2. Wires should be restrained with slots in strain relief and be inline with the axis of its contact cavity. Eight wire ties are included with the strain relief. Figure A. 90 Series Strain Relief Installation. Figure B. icon/i1 Strain Relief Installation. 6-1 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: SECTION 7 CROSS REFERENCE TABLES 90 SERIES RCV MODULE icon MODULE EXTRACTION TOOL CRIMP TOOL KIT LOCATOR/ DIE SET KIT LOADED icon RCV W/ FLYING LEADS LOADED i1 RCV W/ FLYING LEADS RECEIVER CONTACTS 510 104 307 510 160 124 910 112 129 910 102 116 910 102 117 310 123 508 310 128 480 610 149 101 X X X X X X X 90 SERIES ITA MODULE icon MODULE EXTRACTION TOOL CRIMP TOOL KIT LOCATOR/ DIE SET KIT ICON HIGH POWER ITA i1 HIGH POWER ITA LOADED icon ITA FLYING LEADS LOADED i1 ITA W/ FLYING LEADS ITA CONTACTS 510 108 281 510 161 124 910 112 129 610 150 101 X X X X X X X X X 910 102 116 910 102 117 410 123 106 410 128 103 410 123 700 410 128 565 7-1 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: APPENDIX HIGH POWER CONTACT ELECTRICAL SPECIFICATIONS 11.12.438 8.83.348 5.72.225 8.83.348 11.12.438 12.70.500 Receiver Contact Part # 610 149 101 38.48 1.515 36.20 1.425 12.70.500 ITA Contact Part # 610 150 101 Dimensions shown: [millimeters] inches Electrical Specifications Operating Current Operating Voltage Contact Resistance Dielectric Withstanding Voltage Insulation Resistance Temperature Rise 150 Amp Continuous using 2 AWG wire 600VDC or Peak AC 0.35 mohms 1500VDC Minimum 1000 Mohms Minimum +40 C at 150 Amps +30 C at 125 Amps Mechanical Characteristics Mating Force Cycle Life 2.5 lb Max [1.13 Kg] 10,000 cycles Material Contact Body Material Cu Alloy Receiver Contact Body Plating 10μ" Au over 100μ" Ni ITA Contact Body Plating 30μ" Au over 100μ" Ni Operating Temperature -40 C to 125 C 1 of 6 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: APPENDIX High Power Connector Product Performance Specification 1. Scope 1.1 Content This specification covers the performance, tests and quality requirements for the High Power contact and connector system. The High Power contact is a separable electrical connection device, designed and tested using 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL) wire. All High Power contact types are to be used in High Power connector modules. 1.2 Qualification Testing When tests are performed on subject product line, the following procedures shall be used: All inspections shall be performed using applicable inspection plans and product drawings. Upon completion of qualification testing, this specification will be assigned a number and be classified, 2. Applicable Documents 2.1 Content The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of a conflict between requirements of this specification and product drawing, the product drawing will take precedence. In the event of a conflict between requirements of this specification and referenced documents, this specification shall take precedence. 2.2 Documents A. Standards: AMS 2422 EIA 364-06 EIA 364-5 EIA 364-29 EIA 364-21 EIA 364-09 EIA 364-13 EIA 364-17 EIA 364-20 B. Product Drawings: Housings 510104307 510108281 510160124 510161124 Contacts 610149101 610150101 2 of 6 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: APPENDIX 3. Requirements 3.1 Design and Construction Product shall be of design, construction and physical dimensions specified on applicable product drawings. 3.2 Materials A. Female Contact Body - Copper alloy, Internal Contact Beams - Copper alloy Silver plated Gold over Nickel plating per MIL-DTL-45204D B. Male Contact Body - Copper alloy, IP Tip - Thermoplastic Gold over Nickel plating per MIL-DTL-45204D C. Housing G10 Epoxy Glass or Black PPS 3.3 Ratings A. Voltage AC up to 600VAC peak DC up to 600VDC B. Current 2 AWG: 150 ampere maximum C. Temperature -40 C to 125 C 3.4 Performance and Test Description Product is designed to meet electrical, mechanical, and environmental requirements specified in Figure A on pg. 4. Unless otherwise specified, all tests should be performed in free air, room temperature, and ambient environmental conditions. 3 of 6 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: APPENDIX Test Requirements and Procedures Summary Test Description Requirement Procedure Preliminary Examination of Product Meets requirements of product drawing Visual, dimensional, and functional examination per applicable quality inspection plan Operating Current 150 Amp at 40 C Temperature Rise EIA-364-70: 100% of pin positions populated and subjected to 150 Amp current with 2 AWG wire Electrical Contact Resistance 0.35 mω max. EIA-364-06: Subject mated contacts in housing to 100mA and/or Maximum current per wire gage Dielectric Withstanding Voltage 1500 VDC min. EIA-364-20: Test between adjacent contacts in housing, 60 sec. min., Insulation Resistance 1000 MOhm min. EIA-364-21: Test at 500VDC Durability > 10000 Cycles EIA-364-09: Mate and unmate sample for 10000 cycles Mechanical Insertion/retention force < 2 lbf, > 50 lbf EIA-364-05/EIA-364-29: Measure force necessary to insert and remove samples from a module Figure A Mating/unmating forces 2.5 lb max. lbf per contact EIA-364-13: Measure force necessary to engage and disengage samples at a normal rate of engagement of the ITA Current Rating Graph Figure B NOTE: Tested and designed to use with Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. NOTE: For multiple conductor correction factors please reference chart on pg. 5 or http://www.coonerwire.com/amp chart/. 4 of 6 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: APPENDIX VPC High Power Contacts are tested and designed to use with 2 AWG Cooner Wire CW6044-14(UL Rated), AS 105-14(Non-UL), or equivalent. Multiple Conductor Correction Factors Lead Wire Current Carrying Capacity (Ampacity) Insulated Conductor Temperature Rating AWG SIZE at 80 C at 90 C at 105 C at 125 C at 150 C at 200 C 2 170 190 215 232 255 293 Multiply the ampacity rating from above by the correction factor listed below to determine the ampacity rating of a conductor in a multi-conductor cable. Number of Conductors Multiple Conductor Correction Factors Multiply ampacity by factor 4-6 0.80 7-9 0.70 10-20 0.50 Disclaimer: The information shown here has been assembled from sources believed to be reliable, but is not guaranteed by Cooner Wire Co. Cooner Wire Co. is not responsible for its accuracy or reliability. Figure C. Multiple Conductor Correction Factors for 2 AWG wire provided by Cooner Wire. 5 of 6 For the most current information available, visit www.vpc.com.

HIGH POWER CONTACTS AND MODULES USER S MANUAL: APPENDIX 4. Quality Assurance Provisions 4.1 Qualification Testing A. Sample Selection Samples shall be prepared in accordance with applicable instruction sheets and shall be selected at random from current production. Each test group shall consist of a minimum of 5 connectors containing at least 30 contacts total each and equal posts to mate with receptacles. B. Test Sequence Qualification inspection shall be verified by testing samples as specified in Figure A on pg. 4. 4.2 Requalification Testing If changes which significantly affect form, fit or function are made to product or manufacturing process, quality assurance shall coordinate requalification testing, consisting of all or part of original testing sequence as determined by development, product, and quality, and reliability engineering. 4.3 Acceptance Acceptance is based on verification that product meets requirements of Figure A on pg. 4. Failures attributed to equipment, test set-up or operator deficiencies shall not disqualify product. When product failure occurs, corrective action shall be taken and samples resubmitted for qualification. Testing to confirm corrective action is required before re-submittal. 4.4 Quality Conformance Inspection A Certificate of Conformance dimensional inspection must be completed for all samples prior to qualification testing. The applicable quality inspection plan will specify sampling acceptable quality level to be used. Dimensional and functional requirements shall be in accordance with applicable product drawing and this specification. REV Date Rev Change Prepared By 1 11/27/13 Original Release R. Brightwell 2 1/20/2014 Market Release R. Brightwell 3 1/22/2014 Official Market Release C. Slagle 4 3/10/2014 Updated R. Brightwell 5 5/28/2014 Update J. Harman 6 11/25/2014 Update J. Harman 7 5/9/2017 Update J. Diggs 8 Update A. Leger 6 of 6 For the most current information available, visit www.vpc.com.