RADIOKUPOL+ SYSTEM EQUIPMENT CATALOG

RADIOKUPOL+ SYSTEM EQUIPMENT CATALOG cnt-radio.com New Technologies Center Moscow 2016

Company Review New Technologies Center company was formed as a separate subdivision of ARGUT company to carry out research, development and production of professional radio communication devices and equipment that are essential for the customer and not available on the Russian market. The company is a confident leader on the RoIP equipment Russian market for over five years since it has been formed. Within this period, a large number of projects have been implemented. We have manufactured, installed and put into operation over 400 base stations and 70 dispatcher centers in 17 regions of Russia. The total radio coverage area of our base stations have long ago exceeded one million square kilometers. We have solved problems related to providing simple and reliable radio communication for federal highways, large airports (Sheremetjevo, Vnukovo one of the largest in Russia), trade and leisure facilities (e.g. Vegas trade and leisure complex - the largest in Eastern Europe). We have offered also special applications. Among our customers are Russia s Ministry of Internal Affairs, Federal Security Service of Russia, Rescue Services, Rosaeronavigatsia (division of Russian FAA), common commercial customers, and even hams. As of 2016, we initiate supplies of an advanced version of our Radiokupol system Radiokupol+. (means radio dome in Russian) Radiokupol+ is our analog version extension to right away three digital standards. All the equipment and software has been developed by our company including firmware. All the items are produced in Russia. For more detail please see this Catalog. We hope that our equipment can be of use to our international customers as well. Respectfully yours, Stanislav Belovolov General Director Andrey Ermoshkin Technical Director

DR-25 line of Digital Repeaters Repeaters are supplied in three modifications for three most popular digital standards - dpmr Mode 2, DMR Tier II and APCO 25 Phase I Conventional (labelled as DR-25- dpmr, DR-25-DMR, DR-25-APCO). All repeaters now (as of Fall 2016) have the following common features: compatibility with all mentioned digital standard two-way radios, including practically all cheap Chinese manufacturers; RF power is 25W, UHF 430-470 MHz (VHF band production plans are for the end of 2016; 50W - beginning of 2017); mixed operation mode and retransmission of call data (i.e. repeater automatically determines the type of signal - analog or digital, whether the signal has subcarrier or group/individual digital code - and relays the signal to air locally and over IP-network); two versions simple single-site #1 - if the customer is satisfied with a local repeater solution, and a full IP-version #5 capable of measuring RSSI signal level и BER with a possibility of building largescale systems and connecting to all analog Radiokupol dispatcher components (requires a voice digital converter DVC-xxx - of the relevant standard); simultaneous connection of the repeater to 10 IP-devices of the Radiokupol+ system; possibility of upgrading to another digital standard using a special software key, so that the upgrade can be done on-site. DR-25 line of Digital Repeaters General specifications Transmitter Receiver Network interface Nominal value Nominal value Nominal value Operation frequency range: 430 470 MHz Operation frequency range: 430 470 МГц Interface type: 10/100BASE-T Ethernet, IEEE 802.3, 10 or 100 Mbps; RJ-45 connector Transmitter output power: 5 W, 10 W, 25 W. Sensitivity: -117dBm (12dB SINAD or 5% BER) Protocols: ARP, IP, TCP, UDP, IP, HTTP Frequency stability: 2 x10-6 Selectivity: over 80 db @ 25kHz; over 70 db @ 12.5kHz; Audio codecs: g.711 µ/a Law, GSM 6.10 FR, Speex Audio bandpass flatness +within +1 to -4 db: 0 3400 Hz Audio bandpass flatness within +1 to -4 db: 5 3400 Hz Audio delay in analog mode g.711 150 ms, GSM 300 ms, Speex 100 ms Modulation distortion: Not more than 2% at 50% deviation Audio distortions: Not more than 1% at 50% deviation Audio delay in digital mode dpmr - 320 ms, DMR 100 ms, APCO 160 ms Spurious radiation suppression: over 80 db Receiver type: Double Conversion Superheterodyne: IF1-45 MHz, IF2-455 khz Duty cycle: 50% RF Rise Time: Current consumption: Less than 50 ms up to 8 А Radio Gateways and Repeaters 1

Digital Voice Converter (DVC) works with series DR-25 only It is used for logic intersystem switching between various digital standards APCO, dpmr, DMR and analog, each digital subsystem requiring its own Digital Voice Converter (labeled as DVC-APCO, DVC-dPMR and DVC-DMR, respectively). A system general layout is provided in Appendix A at the catalog end. This IP-device has a 1U form-factor and provides conversion of the vocoder audio signal and the relevant call data (e.g. the number of the digital group of one of the digital formats) into PCM voice and service information, so that data and voice can be sent to another digital system (via its relevant DVC), besides it makes it possible to use all the dispatcher infrastructure of an analog Radiokupol system (analog radio communication networks, dispatching, voice logging, interconnect to SIP, PBX, PSTN, etc). Each DVC supports simultaneous connection of up to 16 IP-devices of the Radiokupol+ system. DVC ensures logic integration of various digital and analog systems allowing them to operate in a single group both in static and dynamic modes using a Dispatcher software with the Switching function. For dpmr standard, there are two modifications - DVC-dPMR (supports AMBE+2 genuine vocoder) and DVC-dPMR-C (supports Chinese vocoders AMBE+2C and ASELP designed by the Beijing University). Chinese vocoders are popular with cheap Chinese subscriber radios. You can buy an additional software license to replace a dpmr repeater version with that of DMR/ARCO. Note: The necessity of using our own repeater is related, among other things, to the fact that some standards, such as dpmr and DMR, do not describe interconnection between base stations, and in case of APCO standard protocols described in TIA documents (e.g. ISSI, DFSI) are optional for many equipment suppliers, and are not included in the functionality basic set. 2 Radio Gateways and Repeaters

Radiokupol+ System Analog Components FR-101 Gateway FR-101 is a simple RoIP-gateway for one IP-connection. Two through COM-ports for local devices control. Supplied with SINDIS FR-SF free control software. Connects via radio s audio input/ouput to work with practically any radio (see Appendix B). Two PTT operation modes: COR and VOX RoIP-gateway is setup via a web-interface or a command line prompt (telnet or RS232). Application Radio remote control Integration of two radio communication zones into a single network (without transmitting of group calls) Switching of several radio communication networks using Switching software module (an option for the Dispatcher software) Compatibility Software: SINDIS FR-SF, Dispatcher software, Switching software optional module IP-devices: FR-104, DVC Parameter Value Parameter Value Audio input impedance Balance input, 10 kohm Input impedance of COR, AUX0, AUX1, AUX2 inputs 47 kohm Input level at THD not more than 0.1% from 100 mv to 2 V Switching voltage 2.5 V Audio frequency range 20 Hz 3600 Hz Setup/Configuring Web, telnet or RS232 Output level at THD not more than 0.1% from 100 mv to 2 V Output type Open collector, подтяжка к +5В/100mA Audio output impedance 400 Ohm Interface type Ethernet, connector RJ-45 Connector to connect to radio DB26, female Protocols TCP, UDP, IP Switching voltage 2.5 V Audio codec g.711 ulaw, GSM 6.10 FR Protection up to 10 V Supply voltage 12 V +-4 V, current not more than 0.5 А Power supply connector Coaxial Jack 2.5 mm, «+» in the center Radio Gateways and Repeaters 3

Radiokupol+ System Analog Components FR-104 Gateway Application Radio remote control Integration of up to 10 radio communication zones into a single network (with a possibility of overlapping coverage zones) Capable of switching several different radio communication networks without using Switching software module of the Dispatcher software. Provides continuous radio coverage for highways and complex infrastructure sites. In case of a highway, it is sufficient to have three nominal frequencies one for reception, and two alternately for transmission Compatibility Software: SINDIS FR-SF, Dispatcher software, Switching optional module IP-devices: FR-101, FR-104, Votinger Server, Remote Voice Logging Recorder, DVC FR-104 is an advanced version of FR-101. Up to 10 simultaneous IP-connections of any topology. Capable of working in multicast mode in networks that do not support the given mode on their own. Allows measurement and transmission of the receive signal (RSSI) over IP-network. When transmitter coverage zones overlap, use can be made additionally of a special Voting Server (optional) to collect all such signals, determine the best one and retransmit it to all base stations connected via FR-104 gateway. In case IP-communication with the Voting Server is lost, the gateway switches to the independent local repeater mode. Analysis of information on the signal received by different base stations is ensured continuously to provide seamless handover of a fast moving subscriber. Parameter Value Parameter Value Audio input impedance Balance input, 10 kohm Output type Open collector, voltage elevation to +5В/100 ma Input level at THD not more than 0.1% from 100 mv to 2 V Interface type Ethernet, connector RJ-45 Audio frequency range 20Hz 3600 Hz Protocols TCP, UDP, IP Output level at THD not more than 0.1% from 100 mv to 2 V Audio codec g.711 ulaw, GSM 6.10 FR Audio output impedance 400 Ohm Setup/Configuring Web, telnet or RS232 Input impedance of COR, AUX0, AUX1, AUX2 inputs 47 kohm Connector to connect to radio DB26, female Switching voltage 2.5 V Supply voltage 12 V +-4 V, current not more than 0.5 А Protection up to 10 V 4 Radio Gateways and Repeaters

Radiokupol+ System Analog Components FR-106 Gateway FR-106 SIP-version of FR-101 Allows connection to SIP networks and devices Works with Asterix, CISCO 2911 Receives DTMF-signals from air to ensure dialing Voice announcement into air via a connected radio about call transition in SIP-network Application Ensures connection of SIP-network to a half-duplex radio communication subsystem Compatibility Software: Asterix IP-devices: all supporting SIP-connection Parameter Audio input impedance Input level at THD not more than 0.1% Audio frequency range Output level at THD not more than 0.1% Audio output impedance РТТ output type Network interface Protocols Audio codec Setup/Configuring Connector to connect to radio Supply voltage Power supply connector Value Balance input, 10 kohm from 100 mv to 2 V 20Hz 3600 Hz from 100 mv to 2 V 400 Ohm Open collector, voltage elevation to +5V / 100 ma Ethernet, connector RJ-45 SDP, RTP, TCP, UDP, IP, SIP g.711 ulaw, GSM Web, telnet or RS232 DB26, female 112 В +-4 V, current not more than 0.5 А Coaxial Jack 2.5 mm, «+» in the center Radio Gateways and Repeaters 5

Radiokupol+ System Analog Components FR-101С/104С/106С Gateway Rack mount version for FR-1хх series; Possible installation of up to 4 Gateways in one casing; Convenience for some installations. Parameter Audio input impedance Input level at THD not more than 0.1% Audio frequency range Output level at THD not more than 0.1% Audio output impedance Input impedance of COR, AUX0, AUX1, AUX2 inputs Switching voltage Protection Output type Interface type Протоколы Аудио кодек Setup/Configuring Connector to connect to radio Supply voltage Power supply connector Value Balance input, 10 kohm from 100 mv to 2 V 20 Hz 3600 Hz from 100 mv to 2 V 400 Ohm 47 kohm 2.5 V up to 10 V Open collector, voltage elevation to +5 V / 100 ma Ethernet, connector RJ-45 SDP, RTP, TCP, UDP, IP g.711 ulaw, GSM 6.10 FR Web, telnet or RS232 DB26, female 220 V / 0.5 А АС-016 6 Radio Gateways and Repeaters

Dispatcher software It includes three software modules. Dispatcher Each node corresponds to one IP-connection: visualization of the received signal and the direction of transmission from/to the dispatcher; indication of connection loss; direct communication with other dispatchers; possibility of operation in multicast mode in networks that do not support this mode on their own; audio muting on/off for each window; node (built-in software SIP-module) to establish connection to PSTN via a SIP-network; fine adjustment of the interface and connection parameters. Voice Logging on dispatcher s computer Recording of talks with time/ traffic direction and message length data; possibility of export in *.wav format; visual representation of recordings, possibility of filtering and sorting, using date, time and direction data; automatic deletion of records after the preset storage period expires (storage time period can be set up from 1 to 365 days). Switching (Patching) - optional The module allows simple dragging of the relevant blocks to create visual connections via several simultaneously operating switching channels. Compatibility IP-devices: FR-101, FR-104, KD-02, KD-03, Remote Voice Logging Recorder, Voting Server, DVC Software 7

Dispatcher software Dispatcher Voice Logging record Bridging of radio communication networks and the dispatcher Bridging of a SIP-network and radio communication network User activity Settings panel 8 Software

Control consoles KD-02 Dispatcher Console KD-02 is a simple IP-console designed in a mobile radio form-factor. Simple segment LED display. Up to 5 IP-connections (changing of channels to the loudspeaker ensures listening to one current channel only). Possibility of operation in multicast mode in networks that do not support this mode on their own Parameter Значение Loudspeaker power, W, not less than 5 Audio frequency range 300 Hz 3600 Hz Network interface Interface type Ethernet, connector RJ-45 Protocols HTTP, TCP, UDP, IP Audio codec g.711 ulaw, GSM 6.10 FR General parameters Application Radio remote control Organization of a dispatcher place in any place where IP-connection is available Compatibility Software: SINDIS FR-SF, «Dispatcher» software, Switching module IP-devices: FR-101, FR-104, Voting Server, Remote Voice Logging Recorder, DVC Setup/Configuring External keying unit connector Supply voltage Power supply connector Overall dimensions, mm Web-interface RJ-45 12 V±4 V, current not more than 1.2 А Тип DS1110-01 165x140x45 (WxDxH) Control consoles 9

Operator console KD-03 Dispatcher Console KD-03 is designed in a radio form-factor and features an OLED display to ensure programming of channel alphanumeric names. SIMULTANEOUS connection to 5 IP-devices with adjustable priority and audio volume for each channel (loudspeaker receives all connected channels with indication of calls on the display). Possibility of operation in multicast mode in networks that do not support this mode on their own Parameter Loudspeaker power, W, not less than Audio frequency range Network interface Interface type Protocols Value 5 300 Hz 3600 Hz Ethernet, разъем RJ-45 HTTP, TCP, UDP, IP Audio codec g.711 ulaw, GSM 6.10 General parameters Setup/Configuring External keying unit connector Web-interface RJ-45 Application Radio remote control Organization of a dispatcher place in any place where IP-connection is available Compatibility Software: SINDIS FR-SF, «Dispatcher» software, Switching module IP-devices: FR-101, FR-104, Voting Server, Remote Voice Logging Recorder, DVC Supply voltage Power supply connector Overall dimensions, mm 12 V±4 V, current not more than 1.2 А Type DS1110-01 165x140x45 (WxDxH) 10 Control consoles

Voting Server up to 16 simultaneous IP-connections; selection of the best signal received by remote repeaters connected to the server; online visual display of connection status of all network nodes using web-interface (it is used for diagnostics and setup); setting up base station status (receiver, transmitter, transceiver); incoming data packets buffering to ensure enough time (up to 1 second) for the best signal selection; supporting handover mode between connected base stations; Application The device is designed to organize operation of radio communication networks along highways and on complex infrastructure sites. Compatibility Software: Dispatcher software IP-devices: FR-104, KD-02, KD-03, Remote Voice Logging Recorder, DVC COVERAGE ZONES OVERLAPPING Voting Server DR-25 version #5 DR-25 version #5 DR-25 version #5 IP IP IP Digital or analog call Digital or analog call Digital or analog call Scanning Scanning Subscriber station are in scanning mode Software 11

Voice Logging Recorder The Recoder is designed to ensure remote recording of radio communications WEB-interface with password protection; voice recording with time, traffic direction and message length data; possibility of export in *.wav format; visual representation of recordings, possibility of filtering and sorting using date, time and direction data; automatic deletion of records after the preset storage period expires (storage time period can be set up from 1 to 365 days) recording is made on a SD-card; recording is possible with digitizing without compression (PCM, 64 kb), as well as using GSM 6.10 FR and Speex vocoders (not less than 10 kb). 12 Software

PSC-2-15 Power Supply Controller The Controller converts any reliable power supply source into a UPS for radio equipment. Application KP-2-15 Power Supply Controller provides power supply for various radio engineering equipment with the voltage of 12 to 14 VDC, with the current consumption up to 15A. Output voltage is fed to three pairs of terminals, two of which can be disconnected when either temperature threshold is achieved or by applying an external command via RS-232 port. Parameter Input voltage form power source Backup voltage source Battery charger Disconnection of battery from backup circuit without removing the terminals Number of power supply outputs Output voltage Maximum output current Temperature sensors connection ports, type TS Value 12 15 V 12 V, 7.2 Ah battery available available (using a jumper) 3 12 14 V 15 А 2 Fan port 1 Switchable temperature profiles Audio announcement of controller operation modes Controller control via RS-232 interface ALARM signal BAT_LOW signal 2 (using jumpers) available available Output OK, across external connector Output OK, across external connector Additional components 13

Additional components USB KD-01M Push-to-Talk Speaker-Mic for Operation with Dispatcher software USB Push-to-Talk Speaker-Mic is designed for operation with a «Dispatcher software. Parameter Value Interface USB 1.1 or USB 2.0 Operation current Operation frequency range Not more than 100 mа 300-3400 Hz 14 Additional components

Appendix А General Scheme Digital multi standard system Radiokupol plus Analogue system with analog Radiokupol equipment APCO25 Phase I radio system Voice logging recorder Dispatch software SIP network SIP PBX PSTN Repeater DR-25-APCO FR-101/105+ Analog radio Analog radio system IP network FR-106+ Analog radio APCO25 IP network Repeater DR-25-APCO Dispatch console KD-02/03 RSSI voter IP - NET DVC-APCO25 APCO25 voter DMR Tier 2 radio system dpmr Mode 2 radio system DVC-DMR Repeater DR-25-dPMR Repeater DR-25-DMR DVC-dPMR Repeater DR-25-DMR DMR IP network dpmr IP network Repeater DR-25-dPMR DMR voter dpmr voter Appendix 15

Appendix B List of Radios connected to FR-10Х series Gateways in NTC Laboratory Ref # Radio type Radio control version Remarks 1 Hytera MD785 CORR - 2 Hytera RD985 CORR - 3 IC-3003_4003 (носимая) VOX - 4 IC-7400 VOX - 5 IC-78 VOX - 6 IC-FR3000 CORR - 7 IC-M304 VOX - 8 ICOM FR5000_FR6000 CORR, channel control - 9 ICOM IC-A110 (1) VOX 10 ICOM IC-F110 (2) VOX, channel control 11 ICOM IC-F110 VOX 12 ICOM IC-F1721 VOX 13 ICOM IC-F320 VOX 14 ICOM IC-F521 VOX 15 Motorola GM-360 CORR 16 VERTEX VX-2100 COR Case opening and soldering of access jumpers required Case opening and soldering of access jumpers and adapter assembly (RS232- UART) required Two connectors, control without opening, radio seller warranty kept valid Case opening and soldering of access jumpers required Case opening and soldering of access jumpers required Case opening and soldering of access jumpers required Additional programming to work with service connector required Additional programming to work with service connector required 17 Баклан-5 VOX Special adapter assembly required 18 Гранит-103 VOX - 19 Радон-101 COR 20 РК-201м COR Additional programming to work with service connector required Additional programming to work with service connector required 16 Appendix