3811110 ASSEMBLY INSTRUCTIONS 10 X14 HIGGINS HARDTOP GAZEBO ITEM# L-GZ212PST-4
Parts List Square pole A 4 Round pole B 4 Short arch bar C 4 Long arch bar D 6 Long beam 1 E1 2 Long beam 2 E2 2 Long beam connector E3 2 Short beam 1 F1 2 Short beam 2 F2 2 Corner connector G 4 Middle connector H 4 Corner support bar I1 4 Middle support bar I2 4 Long pipe J1 8 Short pipe J2 8 Pipe connector J3 16 Top frame short brace K1 2 Top frame long brace K2 2 Top roof brace (Corner) L1 4 Top roof connector L2 1
Parts List Top roof brace (Long) M1 2 Top roof brace (Short) M2 2 Top roof cover sheet (Small) Top roof cover sheet (Large) Big roof cover sheet 1 (Short side Big roof cover sheet 2 Short side Big roof cover sheet 3 Short side Big roof cover sheet 4 Short side Big roof cover sheet 5 Short side Big roof cover sheet 1 Big roof cover sheet 2 Big roof cover sheet 3 Big roof cover sheet 4 Big roof cover sheet 5 Big roof cover sheet 6 N1 2 N2 2 O1 2 O2 2 O3 2 O4 2 O5 2 P1 2 P2 2 P3 2 P4 2 P5 2 P6 2 Cover board Top roof Q 4 Corner cover board Big roof R 4
Parts List Middle cover board (Long side) Middle cover board (Short side) S1 2 S2 2 Small top cover board T 1 Finial U 2 Hook V 1 Short support bar 1 W1 2 Short support bar 2 W2 2 Short support bar 3 W3 2 Short support bar 4 W4 2 Long support bar 1 X1 2 Long support bar 2 X2 2 Long support bar 3 X3 2 Long support bar 4 X4 2 Shield Y 4 Mosquito netting Z1 1 Wall Z2 1 Mosquito netting for top roof Z3 1 Tools required: ladder, hammer screwdriver (not included)
Hardware Pack1 AA BB CC DD EE M6X15 Hex bolt M6 Flat washer (small) M6X55 Bolt TBZ00306055HQ M6 Nut TBZ20106HQ M6X15 Bolt 30 PCS 126 PCS 32 PCS 32 PCS 32 PCS WW M6 Wrench 1 PC Fig.1: Insert the short beam 2 (F2) into short beam 1 (F1), fix them by using bolt (AA) and flat washer (BB). Attach the middle connector (H) onto the short beam (F1, F2) with the bolt (AA) and flat washer (BB). Fig.2: Connect the long beam 2 (E2) and long beam 1 (E1) with long beam connector (E3). Screw one hex bolt (AA) and flat washer (BB) onto the underside of the long beam 1 (E1). Attach the middle connector (H) onto the long beam 1 (E1) and long beam 2 (E2) with the bolt (AA) and flat washer (BB). Fig.3: Insert the beam (E1, F1) into beam (F2, E2), fix the corner connector (G) onto the beam with hex bolt (AA) and flat washer (BB). Fig.3-1, Fig.3-2: Fix the pipe connector (J3) onto the four corner beam and two sides of the middle connector (H) with bolt (EE) and flat washer (BB).
Fig.4: Insert the top frame long brace (K2) into top frame short brace (K1), screw them with bolt (AA), flat washer (BB). Fig.5: Insert the corner support bar (I1) into 4 corners of the top frame short brace (K1), tighten with bolt (CC) flat washer (BB) and nut (DD). Fig.6: Use bolt (CC), flat washer (BB) and nut (DD) to connect corner support bar (I1) with corner connector (G). Fig.7: Insert middle support bar (I2) into middle connect pipe of top frame short brace (K1, K2), tighten with bolt (CC), flat washer (BB) and nut (DD). Fig.8: Use bolt (CC), flat washer (BB) and nut (DD) to lock middle support bar (I2) onto middle connector (H). Hardware Pack2 AA BB EE M6X15 Hex bolt M6 Flat washer M6X15 Bolt (small) 8 PCS 20 PCS 12 PCS
Fig.9: Screw the hook (V) into top roof connector (L2). Fig.10: Insert top roof brace (L1) into top roof connector (L2), tighten them with bolt (EE) and flat washer (BB). Fig.10-1: Use bolt (AA) and flat washer (BB) to connect top roof brace (M2, M1 and top roof brace (L1). Fig.11: Fix the mosquito netting for top roof (Z3) onto (M1, M2). Fix the shaped top frame onto connector pipe of top frame short brace (K1) with bolt (EE) and flat washer (BB). Hardware Pack3 BB M6 Flat washer (small) 40 PCS EE M6X15 Bolt 40 PCS
Fig.12: Place the top roof cover sheet (N1, N2) onto the top roof frame, screw them with bolt (EE) and flat washer (BB). Fig.13: Fix the long support bar 4 (X4) onto the middle support bar (I2) with bolt (EE) and flat washer (BB). Fig.14: Fix the long support bar 4 (X4) onto corner support bar (I1) with bolt (EE) and flat washer (BB). (Repeat the procedure for W1, W2, W3, W4, X1, X2, X3, as Fig.13 & Fig.14). Hardware Pack4 BB EE FF M6 Flat washer (small) M6X15 Bolt M6X35 Bolt TBZ00306035HQ 68 PCS 44 PCS 24 PCS Fig.15: Fix the cover board (Q) by using bolt (FF) and flat washer (BB). Fig.16: Fix the small top cover board (T) on the top frame by using bolt (FF) and flat washer (BB), then install the finial (U). Fig.17: Place the big roof cover sheet 1 (O1) on the big roof, fix them by using bolt (EE ) and flat washer (BB).
Fig.18: Place the big roof cover sheet 2 (P2), big roof cover sheet 4 (P4), big roof cover sheet 6 (P6) on the big roof frame, fix them by using bolt (EE) and flat washer (BB). Repeat the procedure for the rest cover sheets). Fig.19: Fix the corner cover board (R) by using bolt (FF) and flat washer (BB), then fix the middle cover board (S1, S2) with bolt (FF) and flat washer (BB). Hardware Pack5 AA BB LL EE KK GG HH DD JJ M6X15 Hex bolt TBZ00106015HQ M6 Flat washer (Small) M6 Flat washer (Large) M6X15 Bolt M6X30 Bolt TBZ00306030HQ Φ8X260MM Round nail TBZ10608260HQ M6X40 Bolt TBZ00306040HQ M6 Nut TBZ20106HQ M6X10 Bolt TBZ00306010HQ 16 PCS 50 PCS 16PCS 24 PCS 10 PCS 24 PCS 8 PCS 8 PCS 32 PCS
Z1 Fig.20: Lift the whole top of the gazebo and put it onto the four square posts (A), fix up with bolt (AA), flat washer (LL) and wrench (WW). Fig.21: Fix the shield (Y) onto the square posts (A), fasten them by using bolt (EE) and flat washer (BB). Fig.22: Fix the middle round post (B) onto the top beam by using bolt (HH), flat washer (BB) and nut (DD).
Fig.23: Insert the long arch bar (D) into the slot of the post, tighten with bolt (EE) and flat washer (BB). Fig.24: Fix the long arch bar (D) onto long beam (E1, E2) with bolt (KK) and flat washer (BB). Repeat the procedure for the short arch bar (C). Fig.25: Let the short pipe (J2) go through the metal ring on the wall (Z2). Insert the short pipe (J2) into the pipe connector (J3) in the middle beam. Then insert the short pipe (J2) into the pipe connector (J3) in corner beam. Repeat the procedure for the long pipe (J1). Note: There will be 8 metal rings hang on each short pipe (J1). 12 metal rings hang on long pipe (J2). Fig.26: Fix the short, long pipe (J2, J1) and the pipe connector (J3) by using bolt (JJ). Note: First assemble the wall (Z2), repeat the same procedure for the mosquito netting (Z1). The mosquito netting should be inside the gazebo. Fig.27: Fasten the gazebo by using round nail (GG). Let the cord go out of the hole and then tie it on the post. Please refer to the pictures below. Z2 Z2 Z2 Z2 Care & Maintenance: Steel components of garden accessories and furniture are treated with rust inhibiting paint that protects them from rust. However, due to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural process. To minimize this condition, it is recommended that care be taken when assembling and handling the product, in order to prevent the paint from being scratched. If scratching or damage occurs, it is recommended that the area be touched up immediately with rust inhibiting paint, which is included in the package. Surface rust can be removed easily using a very light application of common cooking oil. If surface oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may start dripping onto the deck or patio, which may cause damaging stains that may be difficult to remove.