Single-phase Variable Frequency Switch Gear

Similar documents
Single-phase Variable Frequency Switch Gear

Single-phase Variable Frequency Switch Gear

Single-phase Variable Frequency Switch Gear

Single-phase Variable Frequency Switch Gear

Variable Frequency AC Source

Variable Frequency AC Source

Speed Control Of Transformer Cooler Control By Using PWM

Gregory Bock, Brittany Dhall, Ryan Hendrickson, & Jared Lamkin Project Advisors: Dr. Jing Wang & Dr. In Soo Ahn Department of Electrical and Computer

The Single-Phase PWM Inverter with Dual-Polarity DC Bus

Comparison of Lamination Iron Losses Supplied by PWM Voltages: US and European Experiences

VF-nC1 Adjustable Speed Drive Engineering Specification

6. HARDWARE PROTOTYPE AND EXPERIMENTAL RESULTS

S11 Adjustable Speed Drive Engineering Specification

ECET Industrial Motor Control. Variable Frequency Drives. Electronic Motor Drives

ECET 211 Electric Machines & Controls Lecture 9-1 Adjustable-Speed Drives and PLC Installations (1 of 2)

MDSRC Proceedings, December, 2017 Wah/Pakistan

University of North Carolina-Charlotte Department of Electrical and Computer Engineering ECGR 3157 Electrical Engineering Design II Fall 2013

2015 International Future Energy Challenge Topic B: Battery Energy Storage with an Inverter That Mimics Synchronous Generators. Qualification Report

E3 Adjustable Speed Drive Engineering Specification

Frequently Asked Questions (FAQs) MV1000 Drive

AC Drives and Soft Starter Application Guide

When input, output and feedback voltages are all symmetric bipolar signals with respect to ground, no biasing is required.

Active Rectifier in Microgrid

CHAPTER-III MODELING AND IMPLEMENTATION OF PMBLDC MOTOR DRIVE

External Drive Hardware

DESIGN AND IMPLEMENTATION OF SINGLE PHASE INVERTER

Digital-to-Analog Converter. Lab 3 Final Report

Analysis of Advanced Techniques to Eliminate Harmonics in AC Drives

IMPLEMENTATION OF IGBT SERIES RESONANT INVERTERS USING PULSE DENSITY MODULATION

Use of Advanced Unipolar SPWM Technique for Higher Efficiency High Power Applications

Implementation of a Single Phase Z-Source Buck-Boost Matrix Converter using PWM Technique

CHAPTER 3 H BRIDGE BASED DVR SYSTEM

Design Document. Analog PWM Amplifier. Reference: DD00004

Effects of Initial Conditions in a DRSSTC. Steven Ward. 6/26/09

Electronics. RC Filter, DC Supply, and 555

2.1 Performance Standards The UPS is designed with the applicable sections of UL, CUL, and ISO The UPS has UL and CUL listing.

Voltage Source Inverter with Three Phase Preventer and Selector for Industrial Application

Navigation and Thrust System for AUVSI RoboBoat

CHAPTER-5 DESIGN OF DIRECT TORQUE CONTROLLED INDUCTION MOTOR DRIVE

Figure 1 Typical Inverter Block Diagram

L E C T U R E R, E L E C T R I C A L A N D M I C R O E L E C T R O N I C E N G I N E E R I N G

CHAPTER 3 SINGLE SOURCE MULTILEVEL INVERTER

Development of Variable Speed Drive for Single Phase Induction Motor Based on Frequency Control

Applications for Isolated Gate Drivers

AC : PSCAD SIMULATION IN A POWER ELECTRONICS APPLICATION COURSE

Project Proposal. Low-Cost Motor Speed Controller for Bradley ECE Department Robots L.C.M.S.C. By Ben Lorentzen

Pulse Width Modulated Motor Drive Fault Detection Using Electrical Signature Analysis

ARDUINO BASED SPWM THREE PHASE FULL BRIDGE INVERTER FOR VARIABLE SPEED DRIVE APPLICATION MUHAMAD AIMAN BIN MUHAMAD AZMI

An Introduction to Rectifier Circuits

Application Note 1024

Nicolò Antonante Kristian Bergaplass Mumba Collins

Oscillator/Demodulator to Fit on Flexible PCB

CHAPTER 4 CONTROL ALGORITHM FOR PROPOSED H-BRIDGE MULTILEVEL INVERTER

Embedded Test System. Design and Implementation of Digital to Analog Converter. TEAM BIG HERO 3 John Sopczynski Karim Shik-Khahil Yanzhe Zhao

CURRENT CONTROLLER FOR INVERTER BRIDGE DESIGNED FOR GRID-CONNECTED PHOTOVOLTAIC SYSTEM

Fluxgate Magnetometer

EE POWER ELECTRONICS UNIT IV INVERTERS

A Half Bridge Inverter with Ultra-Fast IGBT Module Modeling and Experimentation

Design and Applications of HCPL-3020 and HCPL-0302 Gate Drive Optocouplers

Calhoon MEBA Engineering School. Study Guide for Proficiency Testing Industrial Electronics

EE 368 Electronics Lab. Experiment 10 Operational Amplifier Applications (2)

RV4145A Low-Power Ground Fault Interrupter

Intro To Engineering II for ECE: Lab 7 The Op Amp Erin Webster and Dr. Jay Weitzen, c 2014 All rights reserved.

Active Suspension System. Josh Rose, Xander Serrurier, Rhydon Vassay, Chase Ramseyer Advisor: Steven Gutschlag 4/27/2017

Ch.8 INVERTER. 8.1 Introduction. 8.2 The Full-Bridge Converter. 8.3 The Square-Wave Inverter. 8.4 Fourier Series Analysis

Micro-controller Based Three-phase Voltage Source Inverter for Alternative Energy Source. Abstract

2.017 DESIGN OF ELECTROMECHANICAL ROBOTIC SYSTEMS Fall 2009 Lab 4: Motor Control. October 5, 2009 Dr. Harrison H. Chin

Low Cost Sine Wave Portable Inverter With Over Load Protection Using PIC18F452A

Using Optical Isolation Amplifiers in Power Inverters for Voltage, Current and Temperature Sensing

LABORATORY EXPERIMENT. Infrared Transmitter/Receiver

Interfacing a Flywheel to the Analog Model Power System

Introduction to project hardware

N. Sadeesh 1, P. Hema 2, E. Prasannakumar 3, S. Leelakrishnan 4. IJRASET: All Rights are Reserved

Precision Variable Frequency Drive for AC Synchronous Motor

BME/ISE 3512 Bioelectronics. Laboratory Five - Operational Amplifiers

ME375 Lab Project. Bradley Boane & Jeremy Bourque April 25, 2018

EEL4914 Senior Design. Final Design Report

Hardware Implementation of MOSFET Based High Frequency Inverter for Induction Heating

FPGA Implementation of a PID Controller with DC Motor Application

ECE Senior Design Final Report For. Scalable Regulated Three Phase Power Rectifier. May 10, 2004 Rev. 1.0

CHAPTER 4 MULTI-LEVEL INVERTER BASED DVR SYSTEM

Lab 3 Power electronics

Other Electronic Devices

Experiment 4: Three-Phase DC-AC Inverter

Unipolar and Bipolar PWM Inverter

Closed Loop Magnetic Levitation Control of a Rotary Inductrack System. Senior Project Proposal. Students: Austin Collins Corey West

dspace DS1103 Control Workstation Tutorial and DC Motor Speed Control Project Proposal

Determination of EMI of PWM fed Three Phase Induction Motor. Ankur Srivastava

Solid State Devices (2)

SECTION 16483D ADJUSTABLE FREQUENCY DRIVE - MICRODRIVE (MVX <10-HP)

BME 3512 Bioelectronics Laboratory Five - Operational Amplifiers

CHAPTER 5 CONTROL SYSTEM DESIGN FOR UPFC

Electrical Motor Power Measurement & Analysis

combine regular DC-motors with a gear-box and an encoder/potentiometer to form a position control loop can only assume a limited range of angular

Lecture 19 - Single-phase square-wave inverter

Improving Passive Filter Compensation Performance With Active Techniques

Lecture 6 ECEN 4517/5517

EE 3101 ELECTRONICS I LABORATORY EXPERIMENT 9 LAB MANUAL APPLICATIONS OF IC BUILDING BLOCKS

GENERATION OF SIGNALS USING LABVIEW FOR MAGNETIC COILS WITH POWER AMPLIFIERS

Application Note AN-3006 Optically Isolated Phase Controlling Circuit Solution

Transcription:

Single-phase Variable Frequency Switch Gear Eric Motyl, Leslie Zeman Advisor: Professor Steven Gutschlag Department of Electrical and Computer Engineering Bradley University, Peoria, IL October 15, 2015

EXECUTIVE SUMMARY Single-phase variable frequency switch gear that uses an operator selected output frequency in the range of 1 to 60 Hz and a bipolar direct current (DC) voltage source will be designed, built, and tested. The single-phase variable frequency switch gear will generate a single-phase variable frequency output with a constant Volts/Hertz ratio. Design of the switch gear is limited by the following constraints: the switch gear must use a constant Volts/Hertz ratio, it must use devices rated for a current of 1.5 A RMS, it must have a grounded neutral, and it must be safe. The switch gear should be reliable and efficient. The single-phase variable frequency switch gear designed will contain components necessary for a variable frequency drive. Successful design of single-phase variable frequency switch gear can be extended to three phases, which will pave the way for design of a variable frequency drive. Variable frequency drives (VFD) vary the speed of three-phase alternating current (AC) induction motors by varying the frequency and voltage supplied to the motor. VFDs are important because they provide energy efficiency benefits to industries that consume large amounts of power operating AC machines. Design and implementation of single-phase variable frequency switch gear will be accomplished through the design and implementation of its subsystems. Three subsystems will be designed, built, and tested. The first subsystem, a pulse-width modulated (PWM) generation controller, will take in a frequency select input in the range of 1 to 60 Hz to generate a switched PWM waveform. The second subsystem, gate drive circuitry, will amplify the voltage and current levels of the switched PWM waveform. The final subsystem, a DC-to-AC voltage inverter, will take a positive and negative DC voltage and convert it to AC voltages to generate a single-phase variable frequency output with a constant Volts/Hertz ratio. Devices that will be used to build each subsystem are readily available at Bradley University. Any equipment needed for testing is available in the electrical engineering laboratories at Bradley University. The cost of building the proposed design for single-phase variable frequency switch gear is expected to be under $100. The usefulness of variable frequency drives for energy efficiency is one motivation for designing single-phase variable frequency switch gear. Through the design of the switch gear, the design team expects to gain experience working with power electronics, which is another motivation for the design of variable frequency switch gear. i

ABSTRACT A variable frequency drive controls the speed of a three-phase alternating current motor by varying the frequency and voltage supplied to the motor. Variable frequency drives provide energy efficiency benefits to industries that consume large amounts of power operating alternating current (AC) machines. Single-phase variable frequency switch gear will be designed, built, and tested. Given an operator selected output frequency in the range of 1 to 60 Hz and a bipolar direct current (DC) voltage source, the variable frequency switch gear must provide the selected output frequency at the proper output voltage. Design of the single-phase variable frequency switch gear will be accomplished through the design of its subsystems. The subsystems are a software-based PWM generation controller, gate drive circuitry, and a DC-to-AC voltage inverter. Insulated gate bipolar junction transistor (IGBT) gate drive circuitry will be used to amplify voltage and current levels from the PWM generation controller, and to convert DC bus voltages to AC voltages in the DC-to-AC voltage inverter. Testing of the system will be conducted in the power laboratory at Bradley University. ii

TABLE OF CONTENTS EXECUTIVE SUMMARY... i ABSTRACT... ii I. INTRODUCTION... 1 A. Problem Background... 1 B. Problem Statement... 1 C. Constraints... 1 D. Scope... 1 II. STATEMENT OF WORK... 2 A. System Description... 2 1) System Block Diagram... 2 2) Subsystem Block Diagram... 3 3) High-level Flowchart... 3 4) Nonfunctional Requirements... 3 5) Functional Requirements... 4 B. Design Approach and Method of Solution... 5 1) PWM Generation Controller... 5 2) Gate Drive Circuitry... 5 3) DC-to-AC Voltage Inverter... 5 C. Economic Analysis... 6 D. Project Timeline... 7 E. Division of Labor... 7 F. Societal and Environmental Impacts... 8 III. CONCLUSIONS... 8 IV. REFERENCES... 9 A. SCHEDULE... 10 B. NONFUNCTIONAL REQUIREMENTS... 12 iii

I. INTRODUCTION A. Problem Background A variable frequency drive (VFD) controls the speed of a three-phase alternating current (AC) motor by varying the frequency and voltage supplied to the motor [1]. When AC motors were introduced in 1888, motor speed control required either varying the magnetic flux or changing the number of poles on the motor. In contrast, direct current (DC) motor speed control could be achieved by inserting an external rheostat into the DC field circuit. In the 1980 s VFD technology became reliable and inexpensive enough to compete with traditional DC motor control [2]. VFDs are important because they provide energy efficiency benefits to industries that consume large amounts of power. Through the use of VFDs, industries can match the speed of the motor driven equipment to the load requirements, rather than running the AC motor at full speed with variable speed mechanical drive trains [1]. Another benefit of using VFDs is the smooth startup of AC motors, which extends equipment life by reducing belt, gear, and bearing wear [3]. Previously at Bradley University, a senior project group designed and built a low-voltage singlephase variable frequency AC source using a LabVIEW based cdaq controller from National Instruments to generate a switched pulse-width modulated (PWM) waveform [5]. Alternative software can be used to generate a switched PWM waveform. B. Problem Statement Single-phase variable frequency switch gear that will operate at an output voltage of 120 V AC with frequencies between 1-60 Hz will be designed, built, and tested. The single-phase variable frequency switch gear will use a user-selected input frequency between 1 and 60 Hz and generate an output voltage with a constant Volts/Hertz ratio. C. Constraints Design constraints for the single-phase variable frequency switch gear are shown in Table I. The variable frequency switch gear must provide outputs frequencies in the range of 1-60 Hz. All devices used must be rated for a current of 1.5 A RMS. The switch gear must be safe and must have a grounded neutral. D. Scope Table II lists what is in and out of scope for the design of the single-phase variable frequency switch gear. Single-phase operation is in scope, but three phase operation is out of scope. Generating output frequencies in the range of 1-60 Hz is in scope, but generating output frequencies greater than 60 Hz is out of scope. Driving a resistive load is in scope, but driving a 3-phace AC induction motor is out of scope. 1

TABLE I: CONSTRAINTS FOR SINGLE-PHASE VARIABLE FREQUENCY SWITCH GEAR Constraints Output Frequencies In the range of 1-60 Hz Hardware Devices rated for a current of 1.5 A RMS Safety Safe to operate Neutral Grounded neutral TABLE II: ITEMS THAT ARE IN AND OUT OF SCOPE OF THE DESIGN FOR SINGLE-PHASE VARIABLE FREQUENCY SWITCH GEAR In Scope Single-phase operation Output frequencies in the range of 1-60 Hz Drive a resistive load Out of Scope Three-phase operation Output frequencies greater than 60 Hz Drive an AC induction motor I. STATEMENT OF WORK A. System Description 1) System Block Diagram The system block diagram of single-phase variable frequency switch gear system is shown in Fig. 1. The system has three inputs and one output. The inputs are a frequency select input and a bipolar DC source voltage. The output is a single-phase variable frequency voltage with a constant Volts/Hertz ratio. +VDC Frequency Select Input Variable Frequency Switch Gear Single-phase, Variable Frequency Output with Constant V/Hz Ratio -VDC Fig. 1. System block diagram for single-phase variable frequency switch gear. 2

2) Subsystem Block Diagram Design of single-phase variable frequency switch gear will be accomplished through design of its subsystems. A subsystem block diagram is shown in Fig. 2. A PWM generation controller will use a frequency select input to generate a switched PWM waveform. Gate drive circuitry will amplify the voltage and current levels of the PWM waveform to a useable level for the equipment used in the DC-to- AC voltage inverter. The DC-to-AC voltage inverter will convert DC bus voltages to AC voltages to generate a single-phase variable frequency output with a constant V/Hz ratio. 3) High-level Flowchart The PWM generation controller in Fig. 2 will use software to generate a switched PWM waveform. A high-level flow chart for the PWM generation controller is shown in Fig. 3. The program will start and initialize timers. A 1 V peak-to-peak 15 khz triangle wave and the desired half-wave rectified sine wave will be generated. The amplitude of these two waveforms will be compared. If the amplitude of the triangle wave is less than the amplitude of the sine wave, the output bit will be toggled high. If the amplitude of the triangle wave is greater than the amplitude of the sine wave, the output bit will be toggled low. 4) Nonfunctional Requirements A list of objectives for the design of single-phase variable frequency switch gear is shown in Table III. The system should be reliable and the system should be efficient. As a first test to determine whether or not the system is reliable, the design team will look at how often the system returns the desired output. As a second test to determine whether or not the system is reliable, the design team will look at how long it takes for changes in the input to be seen in the output. Gate Drive Circuitry + VDC Frequency Select Input PWM Generation Controller Upper half PWM Lower half PWM DC-to-AC Voltage Inverter VDC Single-phase, Variable Frequency Output with Constant V/Hz Ratio Fig. 2. Subsystem block diagram for single-phase variable frequency switch gear. TABLE III: NONFUNCTIONAL REQUIREMENTS FOR SINGLE-PHASE VARIABLE FREQUENCY SWITCH GEAR Objectives Reliable Efficient The switch gear should be reliable The switch gear should be efficient 3

Start Initialize Timer Create 1 V p-p 15 khz Triangle Wave Create desired sine wave Check: Triangle < sine Toggle output bit high Check: Triangle > sine Toggle output bit low Toggle output bit low Fig. 3. High-level flowchart for PWM generation controller. TABLE IV: FUNCTIONAL REQUIREMENTS AND CORRESPONDING SPECIFICATIONS FOR SINGLE- PHASE VARIABLE FREQUENCY SWITCH GEAR System Function Specification Overall Provide a constant V/Hz ratio ±10 % tolerance PWM Generation Controller Gate Drive Circuitry DC-to-AC Voltage Inverter Generate a switched PWM waveform Amplify voltage and current levels from PWM generation controller Convert DC bus voltages to AC voltages ±10 % tolerance ±10 % tolerance ±10 % tolerance 5) Functional Requirements Functional requirements for single-phase variable frequency switch gear are shown in Table IV. The overall system shall provide a constant V/Hz ratio. The constant V/Hz ratio should be within ±10 % tolerance of the expected value. The PWM generation controller shall generate a switched PWM waveform. Gate drive circuitry shall amplify voltage and current levels from the PWM generation 4

controller. The amplitude of the amplified signal should be within ±10 % tolerance of the expected amplitude. The DC-to-AC voltage inverter shall convert DC bus voltages to AC voltages. The amplitude of the resulting sine wave from the DC-to-AC voltage inverter should be within ±10 % tolerance of the expected output voltage of 120 V AC. B. Design Approach and Method of Solution Each subsystem will be discussed individually to describe the design approach and method of solution. A detailed testing plan will be discussed with each subsystem. Testing of the single-phase variable frequency switch gear will be conducted in the power laboratory at Bradley University. All equipment that will be used is readily available at Bradley University. 1) PWM Generation Controller An Atmega128 Atmel AVR development board will be used to generate a switched PWM waveform. A 1 V peak-to-peak 15 khz triangle wave and a half-wave rectified sine wave containing the desired frequency between 1-60 Hz will be generated. The amplitude of the triangle wave and half-wave rectified sine wave will be compared. If the amplitude of the triangle wave is greater than the amplitude of the sine wave, the bit on the output port will be toggled high. If the amplitude of the triangle wave is less than the amplitude of the sine wave, the bit on the output port will be toggled low. Every other halfcycle of the switched PWM output will control a separate bit on a given output port (e.g. PA0 and PA1). To test operation of the PWM generation controller, an external digital to analog converter can be used to see the generated triangle wave and half-wave rectified sine wave with an oscilloscope. An oscilloscope can also be used to view the switched PWM output on the two bit. The PWM generation controller is the key component to the design of single-phase variable frequency switch gear. If the Atmega128 cannot be programmed in a timely manner, then a function generator with LM311 comparators will be used as a substitute to generate a PWM signal that will drive IGBTs in the DC-to-AC voltage inverter. 2) Gate Drive Circuitry Two Avago HCPL-3120 IGBT Gate Drive Optocoupler chips will be used. A gate drive with an optocoupler was chosen to protect the Atmega128 board from high voltages used in the DC-to-AC voltage inverter circuitry. The gate drive circuitry will use a high and a low side driver. Each driver will have an 18 V supply. One HCPL-3120 chip will be used for the high-side driver to drive the high-side IGBT in the DC-to-AC voltage inverter H-bridge. A second HCPL-3120 chip will be used for the lowside driver to drive the low-side IGBT in the DC-to-AC voltage inverter H-bridge. To test the gate drive circuitry, a function generator will be used to provide a PWM signal for the gate drive circuitry. The output will be viewed from an oscilloscope to verify that the signal is amplified as desired. 3) DC-to-AC Voltage Inverter A Fairchild FMG2G754560 IGBT pair will be used in the DC-to-AC voltage inverter to convert DC bus voltages to AC phase voltages. Positive and negative DC voltage rails will be used. The DC-to- AC voltage inverter will be made up of the H-bridge shown in Fig. 4. The output of the high-side driver from the gate drive circuitry will be the high-side PWM that will drive the upper IGBT of the H-bridge. The output of the low-side driver from the gate drive circuitry will be the low-side PWM that will drive 5

the lower IGBT of the H-bridge. The output of the H-bridge will be connected to a resistive load connected to ground. Testing of the DC-to-AC voltage inverter will not take place until the gate drive circuitry has been built and tested. To test the DC-to-AC voltage inverter, a function generator will be used to provide a PWM signal to the gate drive circuitry. The output of the gate drive circuitry will drive the IGBTs in the DC-to-AC voltage inverter. Power supplies available in the power laboratory at Bradley University will provide the positive and negative DC rails. The voltage levels at the output of a resistive load will be measured to determine if the IGBTs are switched as desired. C. Economic Analysis The total cost of parts is expected to be $81.97. The components and their respective prices are shown in Table V. The hardware components that will be utilized to complete the design of the singlephase variable frequency switch gear are an Atmega128 Atmel AVR development board, two Avago HCPL-3120 gate drivers, and a Fairchild FMG2G75US60 IGBT module. If the PWM generation controller cannot be successfully implemented with an Atmega128, LM311 comparators will be used. The cost of an Atmega128A development board is $41.99 and is the most expensive part that is required to complete the project. Two Avago HCPL-3120 gate driver chips will be used. Each chip costs $3.27. The second most expensive part is the Fairchild FMG2G75US60 IGBT module, which costs $30. LM311 comparators can be found in packages of 10 for $3.44. The unit price for the comparator is $0.34. The total cost could be minimized by using parts readily available at Bradley University. Parts readily available are the Atmega128, Avago HCPL-3120 chips, and Fairchild IGBT pair. Specifically, the Avago HCPL-3120 chips, Fairchild FMG2G75US60 IGBT, and the LM311 comparators are available through Professor Steven Gutschlag. The software programs that will be used are available to Bradley students on the desktop computers in the electrical engineering department. This eliminates the cost of software for the project. Any oscilloscopes and power supplies that will be used are accessible in Bradley University s power laboratory. +VDC Upper Half PWM Load Lower Half PWM - VDC Fig. 4. H-bridge in the DC-to-AC voltage inverter with its output connected to a resistive load. TABLE V: PARTS LIST FOR SINGLE-PHASE VARIABLE FREQUENCY SWITCH GEAR 6

Part Cost Quantity Cost Atmega128A Atmel AVR development board kit $41.99 1 $41.99 Avago HCPL-3120 $3.27 2 $6.54 Fairchild FMG2G75US60 (IGBT) $30 1 $30.00 LM311 $0.34 1 $0.34 Total Cost $81.97 TASK Month September October November December January February March WEEK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Research Design & Test Gate Driver Code PWM Generation Controller Design & Test Inverter Winter Break Testing Fig. 5. Summarized Gantt chart for single-phase variable frequency switch gear. D. Project Timeline A summarized Gantt chart, shown in Fig. 5, depicts the project timeline. Design of variable frequency switch gear will be accomplished through design of its subsystems. Tasks have been assigned based on the subsystems that will be designed. Design of the PWM generation controller and gate drive circuitry will occur simultaneously. After the gate drive has been designed and built, the inverter will be designed and built. The design of the inverter is dependent on the gate drive as it inverts the output signal from the gate driver. Minor testing will occur as each subsystem is built. The critical path of the tasks starts with the design and implementation of the PWM generation controller and gate drive circuitry. The testing of the DC-to-AC voltage inverter is dependent on successful implementation of gate drive circuitry. Therefore, testing of the DC-to-AC voltage inverter will occur after testing of gate drive circuitry. Testing of the overall system is dependent on successful implementation of each subsystem. The largest portion of work is in the building and the testing of each subsystem. Testing of the switch gear is predicted to take up the majority of the second semester. Testing is scheduled for the second semester due to the dependency on completion of the hardware and software design. The testing task also includes any minor redesigning that needs to take place. A full Gantt chart is shown in Fig. 1 in appendix A. E. Division of Labor Each member is responsible for a different portion of the project. Leslie will be primarily responsible for the design of gate drive circuitry and the DC-to-AC voltage inverter. Eric is responsible for the design and programming of the PWM generation controller. Both members will work on interfacing the software and hardware that has been completed. This includes connecting the gate drive 7

circuitry and DC-to-AC voltage inverter to the Atmega128 board and using the generated code for the PWM generation controller. Lastly, the testing and any minor design changes will be carried out by both team members. A table displaying the division of labor is included in Table I in the appendix A. F. Societal and Environmental Impacts The use of a variable frequency drive impacts industries that consume large amounts of power operating AC machines. The smooth startup to AC motors that VFDs provide increases the lifespan of equipment by reducing belt, gear, and bearing wear. Smooth startup also reduces shaft fatigue to the motor. The less frequent a piece of equipment needs to be replaced positively benefits a company since there is less turnover of equipment. Matching the speed of the motor to load requirements rather than using variable speed mechanical drive trains increases efficiency. An increase in efficiency decreases the power consumption. The environmental impact of less power consumption means there are lower amounts of pollution produced. There are several safety standards that are used for power drive systems to reduce risk of operating equipment. The UL-61800-5-1 standard refers to adjustable speed electric drive systems and the NEC, NFPA 70E standard refers to reducing exposure to major electrical hazards. II. CONCLUSIONS Single-phase variable frequency switch gear will be designed, built, and tested. The switch gear will use an operator selected output frequency in the range of 1 to 60 Hz and a bipolar DC voltage source to generate a single phase variable frequency output with a constant Volts/Hertz ratio. Three subsystems will be constructed to accomplish the design of the switch gear. The subsystems are a PWM generation controller, IGBT gate drive circuitry, and a DC-to-AC voltage inverter. All equipment used is readily available at Bradley University. Testing of the system will be done in the power laboratory at Bradley University. Successful design of single-phase variable frequency switch gear can be extended to three phases, which would pave the way for design of a variable frequency drive. 8

III. REFERENCES [1] Introduction to AC Drives, [Online]. Available: http://vl.graybar.com/automation/ga_manuals/drives/alt%2018 /ITACDS-D.PDF [2] P. Novak. (2009). The Basics of Variable-Frequency Drives, [Online]. Available: http://ecmweb.com/power-quality/basicsvariable-frequency-drives [3] C. Hartman. (2014). What is a Variable Frequency Drive, [Online]. Available: http://www.vfds.com/blog/what-is-a-vfd [4] M. Spear. (2005). Drive up energy efficiency, [Online]. Available: http://www.chemicalprocessing.com/articles /2005/489/ [5] K. Lemke and M. Pasternak. (2014). Variable Frequency AC Source, [Online]. Available: http://cegt201.bradley.edu/ projects/proj2014/vfacs/deliverables/lemke_pasternak_project_proposal.pdf 9

Fig. 1. Gantt Chart for single-phase variable frequency switch gear A. SCHEDULE TASK WEEK Research-Bipolar Vs. Unipolar Research-Rectifier Research-Gate Driver Research-PWM Generator Proposal Presentation Design Gate Driver Code PWM Generation Controller Proposal Document Webpage Release Initial Testing of Gate Driver Design Inverter Initial Testing of Inverter Progress Presentation Performance Review Testing Progress Presentation Student Expo Abstract Project Demonstration Final Presentation Student Expo Poster Printing Student Expo Poster Setup Student Expo Final Report Draft Final Report Final Web Page Advisory Board Poster Printing Advisory Board Poster Presentation 8-Sep 15-Sep 22-Sep 29-Sep 6-Oct 13-Oct 20-Oct 27-Oct 3-Nov 10-Nov 17-Nov 24-Nov 1-Dec 19-Jan 26-Jan 2-Feb 9-Feb 16-Feb 23-Feb 1-Mar 8-Mar 15-Mar 22-Mar 29-Mar 5-Apr 12-Apr 19-Apr 26-Apr PERIODS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 10

TABLE I: SCHEDULE FOR SINGLE-PHASE VARIABLE FREQUENCY SWITCH GEAR START TASK DATE END DATE Research-Bipolar Vs. Unipolar 9/8/2015 9/9/2015 Research-Rectifier 9/10/2015 9/11/2015 Research-Gate Driver 9/15/2015 9/17/2015 Research-PWM Generator 9/22/2015 9/24/2015 Proposal Presentation 9/29/2015 10/1/2015 Design Gate Driver 10/6/2015 10/27/2015 Code PWM Generation Controller 10/6/2015 10/27/2015 Proposal Document 10/6/2015 10/15/2015 Webpage Release 10/27/2015 10/28/2015 Simulate Gate Driver 10/29/2015 11/3/2015 Design Inverter 11/3/2015 11/17/2015 Simulate Inverter 11/17/2015 11/19/2015 Build Components 11/24/2015 12/1/2015 Progress Presentation 11/19/2015 11/19/2015 Performance Review 12/3/2015 12/3/2015 Testing 1/19/2016 3/22/2016 Progress Presentation 2/18/2016 2/18/2016 Student Expo Abstract 3/18/2016 3/18/2016 Project Demonstration 3/24/2016 3/24/2016 Final Presentation 3/24/2016 4/7/2016 Student Expo Poster Printing 4/11/2016 4/11/2016 Student Expo Poster Setup 4/12/2016 4/12/2016 Student Expo 4/14/2016 4/14/2016 Final Report Draft 4/7/2016 4/14/2016 Final Report 4/14/2016 4/28/2016 Final Web Page 4/28/2016 4/28/2016 Advisory Board Poster Printing 4/28/2016 4/28/2016 Advisory Board Poster Presentation 4/29/2016 4/29/2016 11

B. NONFUNCTIONAL REQUIREMENTS Metrics for Reliability are as follows: Units: Design team s assessment of reliability from 0 (worst) to 10 (best) Metrics: Points will be assigned based on the following scale Always gives desired output 10 Almost always gives desired output 6.6 Almost never gives desired output 3.3 Never gives desired output 0 Metrics for efficiency are as follows: Units: Design team s assessment of efficiency from 0 (worst) to 10 (best) Metrics: Points will be assigned based on the following scale shown in Table I TABLE I: POINTS ASSIGNED FOR LEVEL OF EFFICIENCY IN SINGLE-PHASE VARIABLE FREQEUNCY SWITCH GEAR Time it takes for changes in input to be seen in the output (milliseconds) 10 10 20 6.6 30 3.3 >30 0 Value Scale 12