High Quality Coating Systems for Windows and Doors Made of Wood

SOFTWOOD COLLECTION High Quality Coating Systems for Windows and Doors Made of Wood

2

Content Native softwood such as spruce, pine and larch are beautiful. Many people purposefully decide on wood from native forests. It is especially easy to coordinate the appearance of windows and doors made of softwood to adjacent wood building elements such as facades, carports and roof eaves. And when it comes to thermal insulation, softwood is lighter and naturally has somewhat better properties than hardwood. It is also usually the less expensive version. With translucent coating systems from Remmers, softwood in particular can be decorated in brilliant shades of high grade timber. Dimensionally stable wood building elements made of softwood that are protected with Induline coating systems will be eye-catching details on any building and they will stay that way for a long time with very little maintenance. 04 Induline LW-700 05 No Need to Fear Bad Air 06 Remmers System Guide 08 Load Groups 10 Application Overview 13 Remmers Guarantee 14 3

INDULINE SW-900 Softwood Protected from the Bottom Up Permanently Good Softwood, especially sapwood parts, are often not sufficiently resistant against blue stain and other fungi that destroy wood. In many cases, the use of chemical preservatives is recommended and this should be discussed and agreed upon with the client in advance. Remmers has a state-of-the-art solution for this purpose that is approved throughout Europe (BPD), Induline SW- 900*, a product that can be easily integrated into the production sequence of manufacturing wood windows. Properties: Strengthens the surface Saves a lot of sanding work Protects against soft rot and blue stain Protects against moisture, also in end grain areas Makes fibres stand up and hardens them which Allows the fibres to be removed in the 1 st sanding operation Effective in application rates easily ap plied in practice (80 90 ml / m²) Range of use: For dimensionally stable as well as nonstable wood building elements For windows, exterior doors and cladding System products: / GW-201 / GW-208 Induline ZW-400 Induline LW-700 Induline DW-601 Induline Shade of colour Art. No. Bucket: 5.0 l (SU: 96 buckets) Bucket: 20.0 l (SU: 22 buckets) Drum: 120.0 l (SU: 4 drums) SW-900 clear 3776 4 * Use biocidal products with care. Always read the label and product information before using.

INDULINE LW-700 Brilliant, Highly Transparent and Durable The appearance and durability of a window surface mainly depends on the thick-layer stain that is used. Microfoam is often the cause of cloudy-looking coating films. And cloudy-looking coating films are not as resistant to environmental influences such as the impact of hail. Induline LW-700 stands out because of its excellent transparancy and it has been micro-foam optimised. Because of its highly elastic binders, even hail is not really able to harm the coating film and temporary water spots are not a problem either. Several years ago, the Austrian Wood Research Institute independently confirmed that Induline LW-700 is free of air bubbles (ÖNORM B3803). Properties: Highest possible brilliance and surface quality through micro-foam optimisation No water swelling (water spots) after drying Block-free up to at least 70 C Higher UV resistance Reliable colour stability Very good resistance to hail Range of use: For dimensionally stable wood building elements made of softwood and hardwood, e.g. windows, exterior doors, etc. For intermediate and finishing coats System products: Induline ZW-5xx Induline Shade of colour Art. No. Bucket: 5.0 l (SU: 96 buckets) Bucket: 20.0 l (SU: 22 buckets) Drum: 120.0 l (SU: 4 drums) LW-700/20 matt, various shades see Product Programme LW-700/40 silk gloss, various shades see Product Programme 5

NO NEED TO FEAR BAD AIR Perfect Room Climate in Tested Quality When humans stay in the rooms of buildings, their health and well-being not only depend on the climatic conditions that prevail in these rooms (especially temperature and relative humidity) but also on possible contamination of the indoor air. Remmers voluntarily had selected product systems independently tested according to the evaluation scheme issued by the German Committee for Health-Related Evaluation of Building Products (AgBB). The tested Remmers systems fulfilled the requirements of the AgBB evaluation scheme by a clear margin in regard to the emission of volatile organic compounds (VOC), including the limit value for formaldehyde. Benefits for customers: For manufacturers of CE-marked windows and doors (EN 14351-1): Clear statements on emission behaviour (at least for the coating system) can be made. With Remmers systems you are even on the safe side when it comes to the strict requirements on the quality of indoor room air, e.g. when the air could smell bad after coating inside brand new buildings or after renovation. 6

7

REMMERS SYSTEM GUIDE No matter whether translucent or opaque, light-coloured or dark! Here you will find the perfectly matched system for your type of wood! Types of wood / substrates Pine Spruce / Fir Larch Accoya Properties Resin may bleed from the wood; for guarantee: at least 80 % pine heartwood in the outer covering layer Resin galls Resin may bleed & cracks may form; prime with a thin layer (avoid: slipping of the coating); multiple flow coating: run-off problems possible. To stabilise the ph value, 0.5 % Additive VP 20829 must be added to coating materials that are applied in dipping & flow coating procedures. Translucent Intermediate coating applied in a spraying procedure 1 A or 1 B 1 A or 1 B 1 A or 1 B 1 A or 1 B Intermediate coating applied in a flow coating procedure Best possible, all-round protection (moisture) White and grey translucent shades of colour Attention: Shorter maintenance intervals! Natural / highly transparent / clear Attention: Shorter maintenance intervals and special conditions! 2 A or 2 B 2 A or 2 B 2 A or 2 B 2 A or 2 B 3 A 3 A 4 A 4 A 4 A 4 A Opaque Intermediate coating applied in a spraying procedure Best possible sealing of substances in the wood Intermediate coating applied in a flow coating procedure Best possible, all-round protection (moisture) 1 A or 1 B 1 A or 1 B 1 A or 1 B 1 A or 1 B 2 A or 2 B 2 A or 2 B 2 A or 2 B Metallic look 3 A 3 A 8

Remmers Systems A B System Properties System Properties 1 Induline LW-700 / Induline ZW-504i Induline LW-700 Best possible wood protection Especially inconspicuous Induline GW-306 Induline LW-700 / Induline ZW-504i Induline LW-700 Efficient (3-layer system) 2 Induline ZW-502 Induline LW-700 Best possible wood protection Especially inconspicuous Induline GW-306 Induline ZW-502 Induline LW-700 Efficient (3-layer system) Very good all-round protection: Intermediate coating applied in a flow coating procedure 3 WF Induline LW-720 Induline LW-720 Trendy translucent shades of colour; no yellowing of the coating film 4 ligno-stabilising Induline GW-306 ligno-stabilising Induline LW-700 clear VP20181 Induline LW-700 clear VP20181 Best possible wood protection Clear system with the best possible UV protection 1 Induline GW-201 Induline ZW-400 Induline DW-601 Best possible wood protection : concentrate Induline GW-306 white Induline ZW-400 Induline DW-601 Efficient (3-layer system) : ready-to-use 2 Induline GW-208 Induline GW-208 / Induline ZW-502 Induline DW-601 Best possible wood protection : ready-to-use Induline GW-306 white Induline GW-306 white / Induline ZW-502 Induline DW-601 Efficient (3-layer system) : ready-to-use 3 wenge Induline ZW-420 Induline ZW-420 Induline LW-720 Pronounced metallic effect Uncomplicated application 9

LOAD GROUPS Determination of the Load Group for Wood Windows and Exterior Doors The surface protection that will be required the factors named, you can determine or 1. Execution: first coat E will depend on several influence factors: re- check which of the systems is the right sy- 2. Window, species of wood: spruce II gional weather load (e.g. normal climate or stem for each building project. 3. Load: Residential building with 4 sea climate), pronouncement of construc- The application example shows how to storeys on an exposed, tive measures to protect wood (length of do this: slope location, shade of colour eaves), species of wood and type of surface coating (translucent or opaque). RAL 6009 fir green 4.Type of coating: opaque line 7 C With the aid of the table given below and Required coating group: C 7 / II-E Load ID / shade of colour Translucent coating (species group) Opaque coating (species group) I II I II Resin-rich softwood (e.g. pine and larch) Low-resin softwood (e. g. spruce) Resin-rich softwood (e.g. pine and larch) Low-resin softwood (e.g. spruce) Outdoor room climate / indirect weathering Constructive protection from precipitation and sunlight 1 light A A C C Outdoor climate with normal, direct weathering Areas with a normal climate load (no sea or mountain climate) Built-in situation: max. 3 storeys Weather acts directly on windows and doors 2 light * B B C C 3 medium B ** B C ** C 4 dark B ** B C ** C Outdoor climate with extreme, direct weathering Areas with a strong climate load Build-in situation: more than 3 storeys or no constructive protection (e.g. built-in flush with the facade) Weather acts directly on windows and doors 5 light * C C 6 medium B ** C ** C ** 7 dark B ** C ** 10 * When modern UV absorbers are added to certain light shades of translucent coatings, they are able provide as much UV resistance as medium shades of colour. However, a corresponding formulation with these UV absorbers must be examined in each case and approved by Remmers. When these shades of colour are used, the Care Set must be used twice a year. ** Regardless of the surface coating and with an increasing risk when dark coloured coatings are used, bleeding resin cannot be prevented on species of wood that are rich in resin. Light bleeding of resin is natural and does not constitute a defect.

11

Shade of colour 1 larch pine (RC-250) Intermediate and Induline LW-700/20 silk matt stone pine / larch (RC-260) B2/I-E Shade of colour 2 spruce Intermediate and teak (RC-551) Induline LW-700/40 silk gl. teak (RC-550) B3/II-E Shade of colour 3 spruce Intermediate and afromosia (RC-450) Induline LW-700/40 silk gl. afromosia (RC-450) B3/II-E Shade of colour 4 spruce Intermediate and afromosia (RC-450) Induline LW-700/40 silk gl. light oak (RC-351) B3/II-E Shade of colour 5 spruce Intermediate and nutwood (RC-652) Induline LW-700/40 silk gl. teak (RC-550) B4/II-E One-pot system (e.g. for facades)** FT32323 Opaque shade of colour** NCS S 3050-Y30R One-pot system (e.g. for facades)** RC-550 Opaque shade of colour** NCS S 4550-Y60R One-pot system (e.g. for facades)** RC-450 Opaque shade of colour** NCS S 4550-Y40R One-pot system (e.g. for facades)** FT32326 Opaque shade of colour** NCS S 4050-Y30R One-pot system (e.g. for facades)** FT32327 Opaque shade of colour** NCS S 6030-Y40R Shade of colour 6 spruce pine (RC-250) Intermediate and Induline LW-700/40 silk gl. pine (RC-250) B3/II-E Shade of colour 7 larch Intermediate and pine (RC-250) Induline LW-700/40 silk gl. afzelia (RC-330) B3/I-E Shade of colour 8 spruce Intermediate and teak (RC-551) Induline LW-700/40 silk gl. pine (RC-250) B3/II-E Shade of colour 9 spruce Intermediate and teak (RC-551) Induline LW-700/40 silk gl. cherry (RC-490) B3/II-E Shade of colour 10 spruce Intermediate and nutwood (RC-652) Induline LW-700/40 silk gl. nutwood (RC-652) B4/II-E One-pot system (e.g. for facades)** RC-250 Opaque shade of colour** NCS S 2070-Y20R One-pot system (e.g. for facades)** FT32329 Opaque shade of colour** NCS S 3065-Y20R One-pot system (e.g. for facades)** FT32330 Opaque shade of colour** NCS S 3560-Y30R One-pot system (e.g. for facades)** FT32331 Opaque shade of colour** NCS S 3560-Y40R One-pot system (e.g. for facades)** RC-652 Opaque shade of colour** NCS S 8010-Y70R 12 * For especially scratch and hand cream resistant surfaces on doors, use Induline LW-725 / DW-625 instead of Induline LW-700 / DW-601. ** There may be slight deviations in the shade of colour due to the system; these are only approximations!

APPLICATION OVERVIEW The Most Important Remmers Systems and Their Applications Remmers Products Dimensionally stable building elements Building elements with limited stability Building elements that are not stable Windows Exterior doors Winter gardens High quality profiled boards Eave cladding / verges Strut frames, glued trusses, purlin heads, rafters Exterior gates, balconies, framework, folding shutters Exclusive garden pavillions and wood houses Higher quality timber used in gardens Panels made of wooden materials for facade elements Simple wood in gardens such as lattice fences, board walks ** Screen walls, pergolas, carports, etc. Playground equipment Sheds, barns Rustic cladding, boarding BRUSHING QUALITY TRANSLUCENT Remmers HK Stain Priming Priming, intermediate and finishing coat Priming, intermediate and finishing coat Remmers Long-Time Stain UV Priming, intermediate and finishing coat Priming and finishing coat Priming and finishing coat Remmers UV Translucent Top Intermediate and finishing coat Remmers Maintenance Oil ** Priming and finishing treatment ** Remmers UV Weather Protection Stain Priming, intermediate and finishing coat Priming and finishing coat Priming and finishing coat Remmers Compact Stain PU Intermediate and finishing coat Priming and finishing coat Remmers Garden Wood Oils ** Priming and finishing treatment ** BRUSHING QUALITY OPAQUE Remmers Finishing Paint Priming and finishing coat Priming and finishing coat Remmers Compact Varnish PU Priming, intermediate and finishing coat Priming and finishing coat Remmers UV Opaque Top Priming, intermediate and finishing coat Priming and finishing coat EFFICIENT APPLICATION TRANSLUCENT Remmers Induline GW-310 (WF) Priming Priming and finishing coat Priming and finishing coat Remmers / 306 Priming Priming Priming Remmers Induline LW-760 Priming and finishing coat Remmers Induline LW-710 Finishing coat Remmers Induline LW-700 Intermediate and finishing coat Remmers Induline LW-725 * Intermediate and finishing coat Remmers Induline OW-815 ** Priming and finishing treatment ** EFFICIENT APPLICATION OPAQUE Remmers Induline GW-310 opaque Priming Priming, intermediate and finishing coat Priming, intermediate and finishing coat Remmers Induline DW-610 Priming, intermediate and finishing coat Priming, intermediate and finishing coat Remmers Induline DW-660 Priming, intermediate and finishing coat Remmers Induline DW-601 Intermediate and finishing coat Remmers Induline DW-625 * Intermediate and finishing coat * Only suitable for exterior doors ** Surfaces that are subjected to foot traffic may only be treated with the marked products. Detailed information on the range of use of the products named as well as possibilities for combining and handling are found in the latest Technical Data Sheets. 13

SYSTEMS WITH GUARANTEE No Renovation Coating for many Years The logical consequence of the superior properties of Induline Premium Coatings is the Remmers Guarantee for wood windows and doors. The safety that Induline Premium Coatings provide for wood windows and house doors in every step of the application process and the high quality standard of certified manufacturers of wood elements objectively oriented to important standards form the basis for our promise No restoration coatings for many years. But there are further important elements that make the guarantee to the quality assurance concept and valuable marketing instrument it is for the manufacturer of dimensionally stable wood building elements: Acceptance of the operation by a Remmers applications technician All production processes are precisely documented and recorded Systematic training of all involved employees Involvement of the consumer in maintaining the surfaces Remmers Guarantee Through the guarantee, active quality assurance is automatically carried out by the employees of dimensionally stable building element manufacturers well before they are marketed by certified companies. The guarantee helps the element manufacturer to position himself on the market as a quality supplier. In case of doubt, the guarantee is often the decisive factor for the award of an order and allows window & door manufacturers to demand higher prices on the market. 14

REGULAR CARE: The Remmers Care Sets, which were developed especially for house doors and windows, are an important component in the Remmers Guarantee. They are easy to use and extend restoration intervals as well as the service life of the coating: Sets containing cleaner and Care Balsam Closes micro-cracks (e.g. caused by hail) Streak-free on large surfaces Hardly any effect on the degree of gloss 15

www.remmers.de 885 / 11.13 GB