TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic TA7833AF, TA784AF, TA785AF, TA787AF, TA788AF, TA789AF TA7833, 4, 5, 7, 8, 9AF A Three-Terminal Positive oltage Regulator The TA78***AF series consists of fixed-positive- regulator ICs capable of sourcing current of up to A. Features Maximum output current: A Output voltage: 3.3 / 4. / 5. / 7. / 8. / 9. Weight :.36 g (typ.) Output voltage accuracy: OUT ± 4% (@T j = 25 C) Protection function: overcurrent /overheating /safe operating area(soa) Package type: New PW-Mold Pin Assignment Marking side IN 3 2 GND OUT Marking 3 78***AF Product No. (or abbreviation code) Lot No. 2 A line indicates Lead(Pb)-Free Finish. Note: The *** in the each product number is replaces with the of each product. The product(s) in this document ( Product ) contain functions intended to protect the Product from temporary small overloads such as minor short-term overcurrent or overheating. The protective functions do not necessarily protect Product under all circumstances. When incorporating Product into your system, please design the system () to avoid such overloads upon the Product, and (2) to shut down or otherwise relieve the Product of such overload conditions immediately upon occurrence. For details, please refer to the notes appearing below in this document and other documents referenced in this document.
How to Order (Note) TA7833, 4, 5, 7, 8, 9AF Product No. Package Package Type and Capacity TA78**AF (TE6L,NQ TA78***AF (TE6LNQ New PW-Mold: Surface-mount Tape (2 pcs/reel) Note : The ** in each pro-forma product number is replaced with the of each product. Block Diagram INPUT Safe operating area circuit Startup circuit Reference voltage circuit + - Over current protection circuit 2 OUTPUT Thermal shutdown circuit 3 GND Absolute Maximum Ratings (Ta = 25 C) (Note2) Characteristic Symbol Rating Unit Input voltage IN 2 Output current I OUT A Operating Junction temperature T jopr 4 to 35 C Junction temperature T j 5 C Storage temperature T stg 55 to 5 C Power dissipation Ta = 25 C P D Tc = 25 C W Note 2: Do not apply current and voltage (including reverse polarity) to any pin that is not specified. Note 3: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ( Handling Precautions / Derating Concept and Methods ) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). 2
Thermal characteristics Characteristic Symbol Max Unit Thermal resistance, junction to ambient R th (j a) 25 C / W Thermal resistance, junction to case R th (j c) 2.5 C / W Protection Function (reference) (Note 4) Characteristics Symbol Test Condition Min Typ. Max Unit Thermal shutdown T SD IN = OUT + 5 75 C Peak circuit current I PEAK IN = OUT + 5, T j = 25 C.7 A Short circuit current I SC IN = OUT + 5, T j = 25 C.5 A Note 4: Ensure that the devices operate within the limits of the maximum rating when in actual use. 3
TA7833AF (C IN =.33 μf, C OUT =. μf, T j = 25 C, unless otherwise specified) TA7833, 4, 5, 7, 8, 9AF Output voltage OUT IN = 8.3, I OUT = ma 3.68 3.3 3.432 5.8 IN 3.3, 5 ma I OUT A 3.35 3.3 3.465 Line regulation Reg line 5.8 IN 3.3, I OUT = 5 ma 5 5 m Load regulation Reg load IN = 8.3, 5 ma I OUT A 5 5 m Quiescent current I B IN = 8.3, I OUT = 5 ma, 3 8 ma Quiescent current change ΔI B 5.8 IN 3.3, I OUT = 5 ma.3 ma IN = 8.3, I OUT = 5 ma 5 μrms 6.3 IN 3.3, I OUT = 5 ma 67 db IN = 8.3, I OUT = 5 ma, ±.33 m/ C TA784AF (C IN =.33 μf, C OUT =. μf, T j = 25 C, unless otherwise specified) Output voltage OUT IN = 9, I OUT = ma 3.84 4. 4.6 6.5 IN 4, 5 ma I OUT A, 3.8 4. 4.2 Line regulation Reg line 6.5 IN 4, I OUT = 5 A 5 m Load regulation Reg load IN = 9, 5 ma I OUT A 5 m Quiescent current I B IN = 9, I OUT = 5 ma, 3 8 ma Quiescent current change ΔI B 6.5 IN 4, I OUT = 5 ma.3 ma IN = 9, I OUT = 5 ma 5 μrms 7 IN 4, I OUT = 5 ma 66 db IN = 9, I OUT = 5 ma, ±.4 m/ C 4
TA785AF (C IN =.33 μf, C OUT =. μf, T j = 25 C, unless otherwise specified) TA7833, 4, 5, 7, 8, 9AF Output voltage OUT IN =, I OUT = ma 4.8 5. 5.2 7.5 IN 5, 5 ma I OUT A, 4.75 5. 5.25 Line regulation Reg line 7.5 IN 5, I OUT = 5 ma 5 m Load regulation Reg load IN =, 5 ma I OUT A 5 m Quiescent current I B IN =, I OUT = 5 ma, 3 8 ma Quiescent current change ΔI B 7.5 IN 5, I OUT = 5 ma.3 ma IN =, I OUT = 5 ma 5 μrms 8 IN 5, I OUT = 5 ma 64 db IN =, I OUT = 5 ma, ±.5 m/ C TA787AF (C IN =.33 μf, C OUT =. μf, T j = 25 C, unless otherwise specified) Output voltage OUT IN = 2, I OUT = ma 6.72 7. 7.28 9.5 IN 6, 5 ma I OUT A, 6.65 7. 7.35 Line regulation Reg line 9.5 IN 6, I OUT = 5 ma 5 5 m Load regulation Reg load IN = 2, 5 ma I OUT A 5 5 m Quiescent current I B IN = 2, I OUT = 5 ma, 3 8 ma Quiescent current change ΔI B 9.5 IN 6, I OUT = 5 ma.3 ma IN = 2, I OUT = 5 ma 6 μrms IN 6, I OUT = 5 ma 6 db IN = 2, I OUT = 5 ma, ±.7 m/ C 5
TA788AF (C IN =.33 μf, C OUT =. μf, T j = 25 C, unless otherwise specified) TA7833, 4, 5, 7, 8, 9AF Output voltage OUT IN = 3, I OUT = ma 7.68 8. 8.32.5 IN 6, 5 ma I OUT A, 7.6 8. 8.4 Line regulation Reg line.5 IN 6, I OUT = 5 ma 5 5 m Load regulation Reg load IN = 3, 5 ma I OUT A 5 5 m Quiescent current I B IN = 3, I OUT = 5 ma, 3 8 ma Quiescent current change ΔI B.5 IN 6, I OUT = 5 ma.3 ma IN = 3, I OUT = 5 ma 7 μrms IN 6, I OUT = 5 ma 6 db IN = 3, I OUT = 5 ma, ±.8 m/ C TA789AF (C IN =.33 μf, C OUT =. μf, T j = 25 C, unless otherwise specified) Output voltage OUT IN = 4, I OUT = ma 8.64 9. 9.36.5 IN 6, 5 ma I OUT A, 8.55 9. 9.45 Line regulation Reg line.5 IN 6, I OUT = 5 ma 5 5 m Load regulation Reg load IN = 4, 5 ma I OUT A 5 5 m Quiescent current I B IN = 4, I OUT = 5 ma, 3 8 ma Quiescent current change ΔI B 2 IN 6, I OUT = 5 ma.3 ma IN = 4, I OUT = 5 ma 75 μrms.5 IN 6, I OUT = 5 ma 6 db IN = 4, I OUT = 5 ma, ±.9 m/ C 6
for All Products Generally, the characteristics of power supply ICs vary with temperature. The ratings at Tj = 25 assume that a temperature increase has no effect on IC characteristics as ascertained by pulse tests. Standard Application Circuit IN IN OUT TA78xxxAF 2 OUT C IN C 3 GND OUT.33 μf. μf Place C IN as close as possible to the input terminal and GND. Place C OUT as close as possible to the output terminal and GND. Although capacitor C OUT acts to smooth the dc during suspension of output oscillation or load change, it might cause output oscillation in a cold environment due to increased capacitor ESR. It is therefore recommended to use a capacitor with small variations temperature sensitivity. The IC may oscillate due to external conditions (output current, temperature, or the type of the capacitor used). The type of capacitor required must be determined by the actual application circuit in which the IC is used. Usage Precautions If the input terminal shorts to GND in a state of normal operation, the output terminal voltage becomes higher than the input voltage (GND potential), and the electric charge of a chemical capacitor connected to the output terminal flows into the input side, which may cause the destruction of circuit. In these cases, take such steps as a general silicon diode is connected to the circuit, as shown in the above figure There is a possibility that internal parasitic devices may be generated when momentary transients cause a terminal s potential to fall below that of the GND terminal. In such case, that the device could be destroyed. The voltage of each terminal and any state must therefore never fall below the GND potential. Low voltage Do not apply voltage to the Product that is lower than the minimum operating voltage, or the Product s protective functions will not operate properly and the Product may be permanently damaged. Overcurrent Protection The overcurrent protection circuits in the Product are designed to temporarily protect Product from minor overcurrent of brief duration. When the overcurrent protective function in the Product activates, immediately cease application of overcurrent to Product. Improper usage of Product, such as application of current to Product exceeding the absolute maximum ratings, could cause the overcurrent protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. Overheating Protection The thermal shutdown circuits in the Product are designed to temporarily protect Product from minor overheating of brief duration. When the overheating protective function in the Product activates, immediately correct the overheating situation. Improper usage of Product, such as the application of heat to Product exceeding the absolute maximum ratings, could cause the overheating protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. 7
Output 出力電圧 voltage OUT () OUT () Allowable power dissipation PDmax (W) 出力電圧 OUT () Output 出力電圧 voltage OUT OUT () () P D max Ta 2 Condition: Number of IC = Reflow soldering on a ceramic substrate 8 Ta = Tc 6 5 mm 5 mm.8 mm 4 3 mm 3 mm.8 mm Single 2 Single 2 4 6 8 2 4 6 Ambient temperature Ta ( C) OUT Tj 5.25 5.5 5.5 4.95 4.85 TA785AF: IN = IOUT = 5 ma 4.75 5 5 5 Junction 接合部温度 temperature Tj Tj ( C) ( C) OUT IN 6.6 5.5 4.4 3.3 2.2. TA785LS: TA785AF: IOUT=.A, I OUT=.A, Tj=25 Tj=25. 5 5 2 Input 入力電圧 voltage IN IN () () 出力電圧出力電圧 OUT OUT () () Output voltage OUT () Output 出力電圧 voltage OUT OUT () () Peak 出力ピーク電流 output current I PEAK peak (A) I peak Tj 2.5 2..5..5 TA78xxxAF: IN = OUT + 5 Tj = 25 C 5 5 5 Junction 接合部温度 temperature Tj Tj ( C) ( C) OUT Tj 9.5 9.3 9. 8.9 8.7 TA789AF: IN = 4 IOUT = 5 ma 8.5 5 5 5 Junction 接合部温度 temperature Tj Tj ( C) ( C) OUT IN. 8.8 6.6 4.4 2.2 TA789LS: TA789AF: I OUT IOUT=.A, Tj=25. 5 5 2 Input 入力電圧 voltage IN IN () () 8
6.6 I B IN 6.6 I B IN バイアス電流 Quiescent current バイアス電流 I IB B IB (ma) (ma) (ma) 5.5 4.4 3.3 2.2 TA785LS: TA785AF:. I OUT=A, IOUT=A, Tj=25. 5 5 2 Input 入力電圧 voltage IN () () IN () バイアス電流 Quiescent current I B (ma) バイアス電流 IB (ma) IB (ma) 5.5 4.4 3.3 2.2 TA789LS: TA789AF:. IIOUT=A, Tj=25. 5 5 2 Input 入力電圧入力電圧 voltage IN IN () () IN () 6 I B Tj 6 I B Tj バイアス電流 Quiescent current I B IB (ma) 5 4 3 2 TA785AF: IN = IOUT = A 5 5 5 バイアス電流 Quiescent current I B IB (ma) (ma) 5 4 3 2 TA789AF: IN = 4 IOUT = A 5 5 5 接合部温度 Tj ( C) Junction temperature Tj ( C) Junction 接合部温度 temperature Tj ( C) Tj ( C) 3. D I OUT 3. D Tj 最小入出力間電圧差 Dropout voltage D () 2.5 2..5..5 Tj = 4 C 85 25 25 最小入出力間電圧差 Dropout voltage D () () 2.5 2..5..5 IOUT = A.2A A TA78xxAF.2.4.6.8. Output 出力電流 current I OUT I OUT (A) (A) TA78xxAF 5 5 5 Junction 接合部温度 temperature Tj ( C) Tj ( C) 9
Package Dimensions HSOP-3-P-2.3D Unit: mm Weight:.36 g (Typ.)
RESTRICTIONS ON PRODUCT USE 277-EN GENERAL The information contained herein is subject to change without notice. TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc. The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).these TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ( Unintended Usage ). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer s own risk. The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.