Driver LC 53W 5-35mA flexc lp ANCED series Product description Built-in constant current LED Driver New version DC operating with EL marking Adjustable output current between 5 and 35 ma Max. output power 53 W Up to 9.5 % efficiency Nominal life-time up to, h For luminaires of protection class I and protection class II Temperature protection as per EN 6347--3 C5e 5-year guarantee Housing properties Low-profile metal casing with white cover Type of protection IP Interfaces Terminal blocks: 45 push terminals Functions Overload protection Short-circuit protection No-load protection Burst protection voltage kv Surge protection voltage kv (L to N) Surge protection voltage kv (L/N to earth) Suitable for emergency lighting systems acc. to EN 57 Typical applications For linear/area lighting in office applications È Standards, page 4 Wiring diagrams and installation examples, page 4 www.tridonic.com
EL Driver LC 53W 5-35mA flexc lp ANCED series Technical data Rated supply voltage 4 V AC voltage range 98 64 V DC voltage range 76 8 V Max. input current (at 3 V, 5 Hz, full load).7 A Typ. input current (at 3 V, Hz, full load).7 A Leakage current (at 3 V, 5 Hz, full load) < 45 µa Mains frequency / 5 / 6 Hz Overvoltage protection 3 V AC, 48 h Max. input power 57.5 W Typ. power consumption (at 3 V, 5 Hz, full load) 57.5 W Min. output power 7.8 W Max. output power 53 W Typ. efficiency (at 3 V / 5 Hz / full load) 9.5 % λ (at 3 V, 5 Hz, full load).95 Output current tolerance ± 7.5 % Max. output current peak 3 output current + % Max. output voltage 5 V THD (at 3 V, 5 Hz, full load) < % Output LF current ripple (< Hz) ± 5 % Time to light (at 3 V, 5 Hz, full load) 5 ms Time to light (DC mode) <, ms Switchover time (AC/DC) < 5 ms Turn off time (at 3 V, 5 Hz, full load).5 s Hold on time at power failure (output) s Ambient temperature ta (at life-time, h) 4 C Storage temperature ts -4... +8 C Dimensions L x W x H 8 x 3 x mm Hole spacing D 68 mm Ø4, Ordering data Type side fixing feature 8 68 tc Article number 88 Packaging, carton 4, 5 Packaging, pallet 3 Weight per pc. LC 53W 5-35mA flexc lp 8468 5 pc(s). 9 pc(s)..69 kg Specific technical data Type LC 53W 5-35mA flexc lp Test result at 35 ma. Output Min. forward current voltage Max. forward voltage Max. output power Typ. power consumption Typ. current consumption Max. casing Ambient I-out Resistor 4 (at 3 V, 5 Hz, full load) (at 3 V, 5 Hz, full load) temperature tctemperature ta max. 5 ma 7 V 5 V 37.5 W 4.9 W 86 ma 7 C -... +55 C - Type A 75 ma 7 V 5 V 4.3 W 45. W 3 ma 7 C -... +5 C - Type B 3 ma 7 V 5 V 45. W 49.5 W ma 7 C -... +5 C - Type A 35 ma 7 V 5 V 48.8 W 54. W 4 ma 7 C -... +5 C - Type C 35 ma 7 V 5 V 5.5 W 57.5 W 56 ma 7 C -... +5 C open Output current is mean value. 3 Test result at 5 C. 4 Type A is a short circuit plug ( Ω). www.tridonic.com
ACCES- SORIES Plug for output current Product description Ready-for-use resistor to set output current value Compatible with LED Driver serie LC flexc ; not compatible with I- (generation ) and I- (generation ) Resistor is base isolated When using your own resistors, make sure the resistor must be isolated Resistor power.5 W Current tolerance ± % additional to output current tolerance Hot plug of the resistor is not permitted For detailed current setting see table Specific technical data of the respective LED Driver and chapter 3.8 Current setting Ordering data Type Article number Colour of X area Colour of Y area X Y 9 5,5 4,5 xxxx xxxx Marking 7,5 3,5 Resistor value 3,5 Packaging bag Weight per pc. Plug Type A YL 877 Yellow Yellow A. Ω pc(s).. kg Plug Type B YL 877 Yellow Black B 3.6 kω pc(s).. kg Plug Type C YL 8773 Yellow Purple C 8.7 kω pc(s).. kg www.tridonic.com 3
. Standards EN 555 EN 6-3- EN 6-3-3 EN 6347- EN 6347--3 EN 6547 EN 6384 According to EN 57 for use in central battery systems According to EN 6598-- suitable for emergency lighting installations. Thermal details and life-time. Expected life-time Expected life-time Type ta 4 C 5 C 6 C LC 53W 5-35mA flexc lp The LED Driver is designed for a life-time stated above under reference conditions and with a failure probability of less than %. 3. Installation / wiring 3. Circuit diagram 4 V /5/6 Hz L N tc 6 C 7 C x Life-time, h 5, h x 3.4 Installation instructions The LED module and all contact points within the wiring must be sufficiently insulated against 3 kv surge voltage. Air and creepage distance must be maintained. 3.5 Wiring guidelines All connections must be kept as short as possible to ensure good EMI behaviour. Mains leads should be kept apart from LED Driver and other leads (ideally 5 cm distance) Max. lenght of output wires is m. Incorrect wiring can damage LED modules. To avoid the damage of the Driver, the wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.). The current ion has to be installed in the accordance to the requirement of low voltage installation. 3.6 Replace LED module. Mains off. Remove LED module 3. Wait for seconds 4. Connect LED module again Hot plug-in or output switching of LEDs is not permitted and may cause a very high current to the LEDs. 3.7 Earth connection The earth connection is conducted as protection earth (PE). The LED Driver can be earthed via metal housing. If the LED Driver will be earthed, protection earth (PE) has to be used. There is no earth connection required for the functionality of the LED Driver. Earth connection is recommended to improve following behaviour. 3. Wiring type and cross section The wiring can be stranded wires with ferrules or rigid wires with a cross section of.5.5 mm². Strip 8.5 9.5 mm of insulation from the cables to ensure perfect operation of the push-wire terminals. wire preparation:.5.5 mm² 8.5 9.5 mm 3.3 Release of the wiring Press down the push button and remove the cable from front. Electromagnetic interferences (EMI) Transmission of mains transients to the LED output In general it is recommended to earth the LED Driver if the LED module is mounted on earthed luminaire parts respectively heat sinks and thereby representing a high capacity against earth. For Class I application, protection earth need to connected with the metal housing (bottom part). For Class II application, protection earth is no need to be connected, below scenarios should be considered: If the LED Driver housing is screw on a metal part inside the luminaires, both LED Driver and LED module must be isolated. If the LED Driver housing is screw on a plastic part inside the luminaires, the LED module need to be isolated. www.tridonic.com 4
3.8 Current setting 5 ma: Terminal and connected with Ω wire (max. 6 cm length) or resistor Plug Type A BR (article number: 877) 75 ma: Terminal and connected with resistor Plug Type B BR (article number: 877) 3 ma: Terminal and connected with Ω wire (max. 6 cm length) or resistor Plug Type A BR (article number: 877) 35 ma: Terminal and connected with resistor Plug Type C BR (article number: 8773) Type A Type B Type A Type C 4. Electrical values Test at 3 V 5 Hz. 4. Efficiency vs load Efficiency [%] 9 9 9 89 88 87 86 85 84 4 5 6 7 8 9 4. Power factor vs load Power factor,98,97,96,95,94,93,9,9,9,89 4 5 6 7 8 9 4.3 Input power vs load 6 35 ma: All terminals open Input power [W] 55 5 45 4 35 3 5 3.9 Mounting of device Max. torque for fixing:.5 Nm/M4 5 4 5 6 7 8 9 www.tridonic.com 5
4.4 Input current vs load 3 5 Input current [ma] 5 5 4 5 6 7 8 9 4.5 THD vs load THD without harmonic < 5 ma (.6 %) of the input current: 9 8 THD [%] 7 6 5 4 3 4 5 6 7 8 9 5 ma 75 ma 3 ma 35 ma 35 ma 4.6 Maximum loading of automatic circuit breakers Automatic circuit breaker type C C3 C6 C B B3 B6 B Inrush current Installation Ø.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm Imax Time LC 53W 5-35mA flexc lp 3 3 4 5 4 9 4 3 5 A 8 µs 4.7 Harmonic distortion in the mains supply (at 3 V / 5 Hz and full load) in % THD 3. 5. 7. 9.. LC 53W 5-35mA flexc lp < 8 < 5 < 5 < 3 < < Acc. to 6-3-. Harmonics < 5 ma or <.6 % (whatever is greater) of the input current are not considered for calculation of THD. www.tridonic.com 6
5. Functions 6. Miscellaneous 5. Short-circuit behaviour In case of a short circuit on the output side (LED) the LED Driver switches into hic-cup mode. After elimination of the short-circuit fault the LED Driver will recover automatically. 5. No-load operation The LED Driver works in burst working mode to provide a constant output voltage regulation which allows the application to be able to work safely when LED string opens due to a failure. 5.3 Overload protection If the output voltage range is exceeded the LED Driver will protect itself and LED may flicker. After elimination of the overload, the nominal operation is restored automatically. 5.4 DC emergency operation The LED Driver is designed to operate on DC voltage and pulsed DC voltage. For a reliable operation, make sure that also in DC emergency operation the LED Driver is run within the specified conditions. Light output level in DC operation (EOFi): % (cannot be adjusted) The voltage-dependent input current of Driver incl. LED module is depending on the used load. The nominal voltage-dependent no-load current of Driver (without or defect LED module) is for: AC: < 35 ma DC: < 5 ma 6. Isolation and electric strength testing of luminaires Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production. According to IEC 6598- Annex Q (informative only!) or ENEC 33-Annex A, each luminaire should be submitted to an isolation test with 5 V DC for second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The isolation resistance must be at least MΩ. As an alternative, IEC 6598- Annex Q describes a test of the electrical strength with 5 V AC (or.44 x 5 V DC). To avoid damage to the electronic devices this test must not be conducted. 6. Conditions of use and storage Humidity: 5 % up to max. 85 %, not condensed (max. 56 days/year at 85 %) Storage temperature: -4 C up to max. +8 C The devices have to be within the specified temperature range (ta) before they can be operated. 6.3 Additional information Additional technical information at www.tridonic.com Technical Data Guarantee conditions at www.tridonic.com Services Life-time declarations are informative and represent no warranty claim. No warranty if device was opened. www.tridonic.com 7