LC Programmed with HCT s Intella Software Suite 14 I/O (8 inputs & 6 outputs), 1 CAN interface Supply voltage 9-30Vdc The is a robust programmable controller for solenoid-operated proportional valves. It is uniquely designed with configurable I/O and one CAN communication port. This controller has fewer I/O than the DVC710, making it more affordable for smaller stand-alone applications. However, it can also be utilized as a system master module or as an expansion module for the DVC700 series controllers. Advanced stand-alone programmable controller Total system master controller when combined with DVC700 series expansion modules Selectable PID closed-loop processes for pressure/speed control Configurable inputs and outputs Configurable input and output function curves CAN communication Current regulated outputs Open/short detection for diagnostics Auto scale outputs for EDC valves (1 to 125 ma) Rugged and fully encapsulated SAE J1455 environment and load dump compliant IP67, 69K CE Certified Operational Specifications Supply Voltage 9-30 V DC (recommended operating voltage +12 to +28 V DC, absolute maximum +/-32 V DC ) Supply Current Operating Temperature Storage Temperature Weight Dimensions Enclosure NEMA / IP Rating 15 Amps (recommended supply current per power pin 5 Amps, absolute maximum 8 Amps) -40 to +85 C -40 to +100 C 1.29 lbs (0.58 kg) L: 5.50 in (140 mm) x W: 4.70 in (119 mm) x H: 1.65in (42 mm) Solid potted, industry standard Deutsch enclosure with automotive connectors NEMA 6P / IP67, 69K Communication CAN 2.0B (maximum voltage +/-14V DC ) Baud rates 125 kb/s, 250kb/s, 500kb/s, software configurable Protocol SAE J1939, HCT DeviceNet Default baud rate 250kb/s Serial Interface RS232 (maximum voltage Rxd,RTS = +/-15V DC Txd = +/-8 V DC ) 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 1
LC Inputs Digital (Qty 3) Discrete high/low, pulse (RPM and count), software configurable Input Range 0 to +Supply, (Impedance Z = 32.4KΩ) Pulse: RPM/Pulse inputs will accept up to 24kHz on all RPM/Pulse inputs combined Debounce Time 0 to 10 seconds, 10ms intervals, software configurable Analog (Qty 2) 0-5 V DC, digital, (Impedance Z > 100KΩ), software configurable (Note: 2) Universal (Qty 3) 0-5 V DC, 4-20 ma, digital, pulse (RPM, count, and quadrature), software configurable (Note: 2) Input Range Current mode: 0 to +22 ma maximum allowable current, (Impedance Z = 120KΩ) Pulse: RPM/Pulse inputs will accept up to 24kHz on all RPM/Pulse inputs combined Outputs NOTE: 1) Maximum voltage on any input pin +/-32 V DC 2) Analog and Universal inputs have configurable calibration, center and inverse modes Digital (Qty 6) Current Leakage Diagnostics Fly back protection PWM (Qty 2) 3,000 ma sourcing, software configurable Off = 370µA, Supply = +28 V DC Off = 180µA, Supply = +13.6 V DC Open/short circuit detection Integrated : 0-3,000 ma sinking proportional 10-bit resolution, software configurable LC: 0-1,500 ma sinking proportional 10-bit resolution, software configurable Dither Frequency 1-500 Hz, software configurable Diagnostics Open/short circuit detection Fly back protection Integrated Reference Output 0-5 V DC (500 ma Max) Standards Environmental SAE J1455 Immunity 89/336/EEC, EN 61000-6-2 Steam Cleaning & Pressure Washing Temperature Section 4.1.3.2 ESD EN 61000-4-2 Salt Spray Section 4.3.3.1 EMC EN 61000-4-3 Section 4.5.3.2 EMC EN 61000-4-4 Vibration Section 4.10.4.2 RF EN 61000-4-6 Shock Section 4.11.3.4 Emissions 89/336/EEC, EN 61000-6-4 Load Dump Section 4.13.2.2.1.a EN 55011 Certifications CE 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 2
LC Pin Out 30 Pin Cinch Pin Function Pin Function Pin Function L1 TXD M1 CAN H N1 CAN L L2 RXD M2 PWR COM N2 PWR COM L3 RTS M3 PWR COM N3 PWR COM P1 UNI 1 INPUT R1 UNI 2 INPUT S1 UNI 3 INPUT P2 ANA 1 INPUT R2 ANA 2 INPUT S2 DIG 1 INPUT P3 PWR COM R3 5V REF OUTPUT S3 DIG 2 INPUT T1 HS 1 OUTPUT W1 PWM 1 OUTPUT X1 HS 2 OUTPUT T2 HS 3 OUTPUT W2 PWM 2 OUTPUT X2 HS 4 OUTPUT T3 DIG 3 INPUT W3 HS 5 OUTPUT X3 HS 6 OUTPUT Y1 Y2 Y3 + POWER IN + POWER IN + POWER IN 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 3
LC Recommended Operating Parameters / Pin Functions Pin Name Function/Features Range Y1, Y2, Y3 M2, M3, N2, N3, P3 C2, D2, E2 Power In Power Common Universal Inputs (Notes: 3, 4, 6) Positive Power Supply Input Return for Power Supply and Sensors +12V DC to +28V DC (Note: 1) 0 Volts (GND) (Note: 1) Analog 0-5Volts (Notes: 3, Digital Pulse (RPM) Counter Quadrature (Uni_2 & 3) 4-20mA R3 5V REF Reference Output 5 V DC, 500mA S2, S3, T3 Digital Inputs On / Off. RPM 0 to +Supply (Note: 5, 6) P2, R2, Analog Inputs T1, T2, W3, X1, X2, X3 High Side Outputs Analog Active Low Digital Sourcing Discreet Output W1, W2 PWM Outputs Sinking PWM Output Notes: 0-5 V DC 1. Maximum continuous current allowed on any single connector Pin = 8 Amps 2. All limits are guaranteed by testing or statistical analysis 3. Input impedance, 100KΩ with respect to Ground (0V DC ) 4. Input impedance, 120Ω with respect to Ground (0V DC ) 5. Input impedance, 32.4KΩ with respect to Ground (0V DC ) 6. RPM/Pulse inputs will accept up to 24kHz on all RPM/Pulse inputs combined 0 to +Supply On = +Supply 3,000mA (0-1,500mA Off = +Supply 370µA, Supply = Off = +Supply 180µA, Supply = 13.6V DC 10 bit resolution 0 to +Supply 0 to 3,000 ma (0-1,500mA LC) 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 4
LC LED Diagnostic Indicators LED STATE Off On GREEN Flashing GREEN On RED On YELLOW Flashing RED Module Status MEANING There is no power applied to the module. The module is operating in a normal condition. Device is in standby state. May need servicing. Module has an unrecoverable fault. System Disabled active Low Supply Voltage. On GREEN Flashing GREEN On RED Flashing RED CAN Status Communication established with another Master Controller Waiting to establish communication with the Master Controller The device has detected an error that has rendered it incapable of communicating on the network. The DVC Devicenet communication is in a timed-out state % Current O/P Flashing GREEN Flashing RED LED STATE MEANING Off (Outputs Disabled) GRN (0-33%) YEL (34-66%) RED (66-100%) PWM or High Side output Open circuit detected PWM or High Side output Short circuit detected Error Status Off LED STATE No errors MEANING On RED PWM1 Open or Short Detected On GREEN PWM2 Open or Short Detected Flashing YELLOW High Side Open or Short Detected Multi Digit Blink Code Application defined blink codes. 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 5
Error Status % Current O/P CAN Status Module Status High Country Tek LC 4.00 in Physical Description High Country Tek, Inc. Electronic Controls for the Global Fluid Power Industry DVC System Solutions Master Controller Module 5.60 in Notes: 1) All dimensions are in Inches (Millimeters). 2) Use 1/4 x 20 SAE Grade 2 bolts (M6 x 1 ISO Grade 8) * Torque to 4 ft-lbs (5.4 N-m) Dry * Torque to 3 ft-lbs (4.1 N-m) Oiled 2) Mount to a flat hard surface protected from excess heat and moving parts. 3) Factory recommended 18-22 AWG (1.02mm to 0.64mm) TXL, XSL, and GXL automotive grade wire 4) Each Power pin used must be individually fused with an ATO 5, AGC 5 or smaller fuse 1.58 in www.hctcontrols.com Made In USA 30 PIN CINCH CONNECTOR L M N P R S T W X Y 1 2 3 Ø0.29 in 2 PLCS Mount with 1/4" or 6mm Hardware Connections Module Connector - 30 Pin Cinch 581-01-30-002 Mating Connector - 30 Pin Delphi Packard 15492542-B Mating Connector Pins Delphi Packard 12103881 Part Number LC Description 2x dual channel master controller, 1x CAN ports (0 to 3 Amp output) 2x dual channel master controller, 1x CAN ports (0 to 1.5 Amp output) 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 6
LC Output Features Output Groups (Qty2) Dual Coil High-Side Single Coil High-Side Single Coil Low-Side High-Side Only Designed with 3 output groups consisting of 2x digital sourcing outputs and 1x PWM sinking output allowing the user to configure each output group in one of four different configurations. Reference Figures 1 and 2. To be used with proportional dual coil applications Independently control a single proportional output and a single discrete output Independently control a single proportional output and two discrete outputs Independently control two discrete outputs Figure 1: output configurations. Figure 2: example wiring diagram using two different output group configurations. 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 7
LC High Country Tek www.enovationcontrols.com 5311 S 122nd East Ave. Tulsa, OK 74146 Copyright Enovation Controls 2018 This data sheet may contain mistakes and printing errors. The information in this publication is regularly checked and corrections made in the next issue. Please check our website for latest version. Enovation Controls accepts NO liability for technical mistakes or printing errors, or their consequences. 2018 Enovation Controls 021-00370 Rev. C www.enovationcontrols.com 8