Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 000000000 0W Front End Power System RCP-0 series { File Name:RCP-0PEC 018-01-15
0W Front End Power System RCP-0 series SPECIFICATI MODEL RCP-0-1 RCP-0-4 RCP-0-48 DC VOLTAGE 1V 4V 48V RATED CURRENT CURRENT RANGE 0 ~ 0 ~ 0 ~ RATED POWER 8W RIPPLE & NOISE (max.) Note. 150mVp-p 00mVp-p 300mVp-p OUTPUT VOLTAGE ADJ. RANGE(SVR) 11.6 ~ 1.4V 3. ~ 4.8V 46.3 ~ 49.7V VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0% LINE REGULATI ±0.5% ±0.5% ±0.5% LOAD REGULATI SETUP, RISE TIME HOLD UP TIME (Typ.) ±0.5% 0ms, 60ms/30VAC at full load 16ms/30VAC at full load ±0.5% ±0.5% VOLTAGE RANGE Note.4 ~ 64VAC 17 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz INPUT EFFICIENCY (Typ.) 81% 87% 89% AC CURRENT (Typ.) 8.5A/115VAC 4.5A/30VAC 10.5A/115VAC 5.5A/30VAC 11A/115VAC 5.5A/30VAC INRUSH CURRENT (Typ.) LEAKAGE CURRENT COLD START 50A <1.1mA / 30VAC 105 ~ 15% rated output power OVERLOAD Protection type : Constant current limiting, recovers automatically after fault condition is removed PROTECTI 13. ~ 16.V 6.4 ~ 3.4V 5.8 ~ 64.8V OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down AUXILIARY POWER 5V @ 0.3A REMOTE - CTROL By electrical signal or dry contact :short :open REMOTE SENSE Compensate voltage drop on the load wiring up to 0.5V FUNCTI OUTPUT VOLTAGE PROGRAMMABLE Adjustment of output voltage is allowable to ~ 110% of nominal output voltage. Please refer to the Function Manual. DC OK SIGNAL The isolated TTL signal out, Please refer to the Installation Manual AC OK SIGNAL The isolated TTL signal out, Please refer to the Installation Manual OVER TEMP WARNING Logic " High" for over temperature warning, Please refer to the Installation Manual, isolated signal WORKING TEMP. -0 ~ +60 (Refer to "Derating Curve") WORKING HUMIDITY 0 ~ % RH non-condensing ENVIRMENT STORAGE TEMP., HUMIDITY -40 ~ +85, 10 ~ 95% RH non-condensing TEMP. COEFFICIENT ± 0.0%/ (0 ~ 50 ) VIBRATI 10 ~ 500Hz, G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY & EMC (Note 5) OTHERS NOTE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATI RESISTANCE EMC EMISSI EMC IMMUNITY MTBF DIMENSI PACKING UL60950-1, TUV EN60950-1, EAC TP TC 004 approved I/P-O/P:3KVAC I/P-FG:KVAC O/P-FG:0.7KVDC I/P-O/P, I/P-FG, O/P-FG:M Ohms / 500VDC / 5 / 70% RH Parameter Standard Conducted Radiated Harmonic Current Voltage Flicker EN5504, EN6104-3, EN60-6- Parameter ESD Radiated EFT / Burst Surge Conducted Magnetic Field Voltage Dips and Interruptions EN5503 (CISPR3) / EN55011 (CISPR11) Class B EN5503 (CISPR3) / EN55011 (CISPR11) Class B EN60-3- ----- EN60-3-3 ----- Standard EN60-4- EN60-4-3 EN60-4-4 EN60-4-5 EN60-4-6 EN60-4-8 EN60-4-11 74K hrs min. Telcordia SR-33 (Bellcore) ; 107.3K hrs min. MIL-HDBK-17F (5 ) 95*17*41mm (L*W*H) 1.93Kg; 6pcs/1.6Kg/1.04CUFT Test Level / Note Test Level / Note Level 3, 8KV air ; Level, 4KV contact Level 3 Level 3 Level 4, 4KV/Line-Earth ; Level 3, KV/Line-Line Level 3 Level 4 >95% dip 0.5 periods, 30% dip 5 periods, >95% interruptions 50 periods File Name:RCP-0PEC 018-01-15
0W Front End Power System RCP-0 series Block Diagram PFC fosc : 110KHz PWM fosc : KHz I/P EMI FILTER ACTIVE INRUSH CURRENT LIMITING & PFC POWER SWITCH- ING O.L.P. & FILTER CURRENT SHARE ORING DIODE CURRENT SHARE PFC CTROL PWM CTROL DETECTI CIRCUIT V_TRIM O.V.P. CTROL / I C FUNCTI OPTIAL I C REMOTE - AUX POWER FAN DETECTI CIRCUIT & FILTER AC_OK DC_OK T_ALARM AUX POWER (5V/0.3A) AUX GND Static Characteristics 80 70 MODEL INPUT 180~64VAC 115VAC 1V 4V 48V 8W 8W LOAD (%) 60 50 40 VAC VAC 648W 54A 864W 36A 8W 7.W 18.9A 95 115 64 INPUT VOLTAGE (VAC) 60Hz Derating Curve Efficiency vs Load (48V Model) 95 LOAD (%) 80 60 40 0-0 0 10 0 30 40 50 60 70 AMBIENT TEMPERATURE ( ) EFFICIENCY (%) 85 80 75 70 65 10% 0% 30% 40% 50% 60% 70% 80% % % LOAD The curve above is measured at 30VAC. File Name:RCP-0PEC 018-01-15
0W Front End Power System RCP-0 series Function Manual 1. Voltage Drop Compensation 1.1 Remote Sense The remote sense compensates voltage drop on the load wiring up to 0.5V. RCP-0 8 9 LOAD Sense lines should be twisted in pairs 1. Local Sense The, have to be connected to the,, respectively, as the following diagram, in order to get the correct output voltage if Remote Sense is not used. RCP-0 0 5 1. Remote / Control The power supply can be turned / together or separately by using the "Remote -" function. Between Remote - and Power Supply Status RCP-0 REMOTE - 7 9 Switch Short Switch Open PIN7 REMOTE / PIN8 PIN9 File Name:RCP-0PEC 018-01-15
0W Front End Power System RCP-0 series 3. Output Voltage Programming (or, PV / remote voltage programming / remote adjust / margin programming / dynamic voltage trim) In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed to ~110% of the nominal voltage by applying EXTERNAL RESISTANCE. PIN8 PIN9 PIN 13 V-TRIM RCP-0 V-TRIM 8 13 9 R1 R LOAD &, & also need to be connected on CN501 3.1 RCP-0-1 110 98 108 96 106 94 104 9 10 180K 40K 350K 560K 1.M NC R1 ( Ω) NC 300K 10K 6K 31K 13K R ( Ω) 3. RCP-0-4 98 96 94 9 110 108 106 104 10 560K 750K 1M 1.6M 3.3M NC R1 ( Ω) NC 330K 130K 6K 30K 10K R ( Ω) 3.3 RCP-0-48 110 98 108 96 106 94 104 9 10 1.3M 1.7M.4M 3.6M 7.6M NC R1 ( Ω) NC 345K 140K 70K 36K 15K R ( Ω) 4. I C Bus Interface Option For the details of I C option, please refer to the Installation Manual. File Name:RCP-0PEC 018-01-15
0W Front End Power System RCP-0 series Mechanical Specification Case No. 95A Unit:mm 41 7.1 1.5 95 4 17 39.1 66 46.3 3.6 5 max. CN501 SVR 46 DC OK AC OK Air flow direction LED Status Indicators & Corresponding Signal at Function Pins Function LED Description AC-OK AC-NG DC-OK DC-NG T-OK T-ALARM ---- ---- When input voltage 8V± 4V When input voltage 8V± 4V When output voltage 80% ± 5% of Vo rated. When output voltage 80% ± 5% of Vo rated. When the internal temperature (TSW1 & TSW short) is within safe limit When the internal temperature (TSW1 or TSW open) exceeds the limit of temperature alarm *Signal between function pin and "". Input / Output Connector Pin No. Assignment( CN501) : Postronic PCIB4W9M400A1 * Signal 0 ~ 0.5V 4.5 ~ 5.5V 0 ~ 0.5V 4.5 ~ 5.5V 0 ~ 0.5V 4.5 ~ 5.5V PSU Output 1 3 5 7 10 13 16 19 3 Mating Housing Postronic PCIB4W9F400A1 4 6 9 1 15 18 1 4 Pin No. Function Description 1,,4 (signal) Positive output voltage. 3,5,6 (signal) Negative output voltage. 7 Remote- Each unit can separately turn the output on and off by electrical or dry contact. Short:, Open:. 8 Positive sensing for Remote Sense. 9 Negative sensing for Remote Sense. 10 AC-OK Low : When input voltage is 8Vrms +/-4V. High : When input voltage in 8Vrms +/-4V. (Note.1) 11 DC-OK High : When Vout 80%+/-5%. Low : When Vout 80%+/-5% (Note.1) 1 CS 13 14 15 16 17 18 19,0,1 3 4 V-TRIM T-ALARM +5V-AUX GND-AUX SCL SDA A0,A1,A FG AC/L AC/N Current sharing signal. When units are connected in parallel, the CS pins of the units should be connected to allow current balance between units. Connection for output voltage programming. High : When the internal temperature is within safe limit. Low : 10 below the thermal shut down limit. (Note.1) Auxiliary voltage output, 4.3~5.3V, referenced to GND-AUX(pin 7). The maximum load current is 0.3A. This output has the built-in "Oring diodes" and is not controlled by the remote / control. Auxiliary voltage output GND. The signal return is isolated from the output terminals ( & ). Serial clock used in the I C interface option. Refer to the Instruction Manual. (Note.1) Serial data used in the I C interface option. Refer to the Instruction Manual. (Note.1) I C interface address lines. Refer to the Instruction Manual. AC Ground connection. AC Line connection. AC Neutral connection. Note1: Non-isolated signal, referenced to the output terminal. File Name:RCP-0PEC 018-01-15