HAFEN FEXIBE BOT CONNECTIONS MT-FBC 10.1-E FRAMING SYSTEMS
HAFEN FRAMING SYSTEMS Contents Fotolia HAFEN Framing s, HAFEN Bolts - General overview - Product range - overview: HAFEN Framing channels - Information on dimensioning - Heav dut framing sstem - Medium dut framing sstem - ight dut framing sstem 3 8 10 12 27 36 HAFEN Framing Sstem Accessories - Threaded rods, heagonal headed bolts, nuts, washers - end caps, channel cover strips - Cantilevers 44 46 47 Materials, design properties, constructions - Materials, designs of framing channels and bolts - Profile data HAFEN Framing channels at a glance - Product range overview: HAFEN Bolts - oad capacit of welded/anchor bolt framing sstems - HAFEN Framing channels as compression elements - Calculation of bolt lengths 48 50 54 56 58 59 e 2 e 1 F SZ HAFEN Framing s in engineering and equipment construction - Information on dimensioning NEW! 60 F F R F Q Appendi: - Specification tets - Inde - Addresses/contact 66 67 68 2 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS General Information Adjustable HAFEN fiing sstems offer a whole range of benefits: The adjustable HAFEN channel-bolt sstem is a supporting as well as a fiing sstem Full fleibilit in positioning and dimensioning the bolt connections Choice of corrosion protection: - Strip galvanied framing channels for low demands - Hot-dip galvanied framing channels for high demands - Framing channels in stainless steel for maimum requirements Quick assembl and adjustment of equipment and structural components Change or up-date entire projects with standard tools No specialist required to carr out modifications on site Dust free and low noise levels when modification work is done on site Corrosion protection is not compromised b bolting A large selection of standard channels with good load bearing characteristics. All the loads stated in this catalogue are permissible loads With HAFEN Framing channels ou avoid: Time consuming planning of infleible bolted fiings Costl manufacturing of bolt fiings Costl corrosion protection work when upgrading alread completed structural components i.e. when adjusting components to site HAFEN s All hot-rolled HAFEN Profiles and some of the light framing channels are also available as HAFEN HTA/HZA Cast-in channels. Both versions use the same bolts and locking plates. You can find more information on HAFEN s in our catalogue " HAFEN Cast-in channels, Product Information, B". Qualit Qualit is an outstanding feature of our products. HAFEN materials and products are subject to stringent qualit controls. A qualit audit b the Germanic lod Certification GmbH confirmed that our qualit management sstem meet the demands of the DIN EN ISO 9001:2008 standard. Certificate-no. QS-281 HH 2011 HAFEN MT-FBC 10.1-E www.halfen.com 3
HAFEN FRAMING SYSTEMS Framing s Framing channels HM, H, HZM and HZ Heav Dut Medium Dut ight Dut Materials / Statics Hot-rolled framing channels The hot rolling process makes these framing channels ideall suitable for: heav loads dnamic loads or welding Smooth channels HM Ver high tensile loads of up to 31 kn are possible Using nibbed bolts high longitudinal loads of up to 7.5 kn are possible (applies onl to steel) Toothed channels HZM Toothing allows high longitudinal loads up to 22 kn 3 channel sies for maimum efficienc Cold-rolled framing channels Cold-rolled channels are economic for lower loads. s are available with holes or without holes. Cold-rolled framing channels H, HM For lower loads in longitudinal channel direction Economic due to large selection of channels Toothed channels HZ, HZM For high loads in longitudinal channel direction Non-slip connection for high channel loads Roller-bearing fiing of a cablewa Welding-jig, locomotive construction Cantilever fiing on a vertical conveor sstem 4 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts HAFEN Bolts HS, HZS and HSR Tpe HS Tpe HSR Tpe HZS HAFEN Bolts; plain Suitable for all channels oad bearing capacit in two directions Marked at shank end with one notch Identifing HAFEN Bolts Bolt identification on the bolt head HAFEN Bolts with nibs Onl suitable for use in hot-rolled channels from the heav dut sstem Nibbed; therefore non-slip, load bearing in all directions The hook-head bolt prevents turning under vibration Marked at shank end with two notches (applies onl to steel) ocation of nib on bolt HAFEN H4.6 4.6 H 4.6 Toothed HAFEN Bolts For toothed framing channels HZM and HZ Toothing also provides positive load bearing transmission in longitudinal channel direction. The risk of slipping is eliminated Marked at shank end with two notches Teeth in channel Manufacturer (for individual dimensions) strength grade or material grade Heav Dut Medium Dut ight Dut HS All Tpes HZS 41/22 HZS 41/41 Notches on the shank tip: HSR All Tpes HZS 38/23 HZS 29/20 HAFEN H4.6 4.6 H 4.6 HAFEN H8.8 4.6 H 8.8 4.6 Strength class 4.6 galvanied or hot-dip galvanied Strength class 8.8 galvanied or hot-dip galvanied HAFEN -50 H 4.6 HAFEN -70 H 4.6 material qualit - 50 stainless steel material qualit - 70 stainless steel Marking at the shank end of the HAFEN Bolts: After assembl check the correct orientation of the marking on the shank end of the bolts. The slot or slots must be at right angles to the channel length. Materials / Statics 2011 HAFEN MT-FBC 10.1-E www.halfen.com 5
HAFEN FRAMING SYSTEMS ocking Plate ocking plate GWP Heav Dut Medium Dut ight Dut ocking plates (channel nuts) allow an metric bolt or threaded rod to be used. Order eamples Order eample of framing channels Tpe Material ength (mm) ocking plates with grip (see Medium dut Framing sstem page 35). The toothing grips the channel lips. HM 50/30 6070 Order eample of bolts Tpe Thread ength (mm) Material ocking plates with spring are used in particular for securing plates or panels. (see Medium dut Framing sstem page 35). HS 50/30 M20100 -S or use the 12-digit Order-no. e.g. 0280.200-00003 or use the 12-digit Order-no. e.g. 0350.090-00068 Materials / Statics If ou have an further questions: Our technical department and our field support technicians will gladl advise and support ou in resolving questions concerning HAFEN assembl sstems. HAFEN Engineering Support Tel.: +49 (0) 2173-970 9021 E-Mail: es.fra@halfen.com www.halfen.de 6 2011 HAFEN MT-FBC 10.1-E www.halfen.com
Framing s The advantages at a glance Whether for low or ver high loads: ou will alwas find a cost effective solution for our requirements in the HAFEN product range of framing channels and bolts. Versatile and adaptable Adjustable assembl. All connections can be adjusted at an time; the are easil replaced or etended. Almost unlimited in its range of application; e.g. Building construction, industrial construction, steel construction, engineering construction, vehicle manufacturing and man other sectors. Heav dut framing sstem The heav dut framing channel is predominantl hot-rolled and particularl suitable for heav loads. Medium dut framing sstem All medium dut framing channels have the same profile width and are compatible with the innovative HAFEN Powerclick assembl sstem. Heav Dut Medium Dut ight Dut Secure and reliable Corrosion protection remains intact after bolting. arge selection of standard channels with ver good load bearing capacities. Toothed channels for non-slip connections. ow dut framing sstem The low dut framing channel is the prefect fiing solution for low loads. Materials / Statics 2011 HAFEN MT-FBC 10.1-E www.halfen.com 7
HAFEN FRAMING SYSTEMS Product Range Overview: Framing s + HAFEN Bolts Heav dut framing sstem Heav Dut Medium Dut ight Dut Hot-rolled Cold-rolled HM 72/48 HM 52/34 HM 50/30 HM 49/30 HM 50/40, H 50/40 HM 486 HS 72/48, HSR 72/48, GWP 72/48 Page 12 Page 14 Page 15 Page 15 Page 16 Page 16 Medium dut framing sstem 30 HS 50/30, HSR 50/30, GWP 50/30 Cold-rolled Cold-rolled, toothed Cold-rolled Cold-rolled, toothed HM 41/41, H 41/41 HZM 41/41, HZ 41/41 HM 41/62, H 41/62 HM 41/83, H 41/83 HM 41/22, H 41/22 HZM 41/22, HZ 41,22 Page 27 Page 28 Page 29 Page 30 HZS/HS 41/41, HZS 41/22 GWP 41/41, GWP 41/22 Page 31 Page 32 ight dut framing sstem Cold-rolled Materials / Statics HM 36/36, H 36/36 HM 38/17 HM 28/28, H 28/28 HM 26/26, H 26/26 HM 28/15, H 28/15 HM 315 Page 36 HS 38/17, GWP 38/17 Page 36 Page 38 Page 39 HS 28/15, GWP 28/15 Page 40 GWP 28/15 Page 40 8 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Product Range Overview: Framing s + HAFEN Bolts Hot-rolled Cold-rolled Hot-rolled, toothed Cold-rolled, toothed HM 40/22 HM 40/25 HM 422 HZM 53/34 HZM 38/23 HZM 29/20 HZ 63/63 Cold-rolled 40 25 18 22 HS 40/22, HSR 40/22, GWP 40/22 H 41/41 H 41/22 53 34 Page 18 Page 18 Page 18 Page 20 Page 22 Page 24 Page 26 Page 33 Page 33 NEW! HZS 53/34 HZS/HS 38/23, HS 38/17, GWP 38/17 HZS/HS 29/20, HS 28/15, GWP 28/15 HZS 41/22, HZA/HS 41/41, HZS 41/22, GWP 41/41 Heav Dut Medium Dut ight Dut Cold-rolled HM 20/12, H 20/12 Page 42 HS 20/12, GWP 20/12 Material; finishes: hot-dip galvanied or plate rolled blank WB sendimir galvanied SV Stainless steel Stainless steel A2 Stainless steel HCR For further information on Materials and finishes see page 48 HZM/HZ toothed profiles Materials / Statics 2011 HAFEN MT-FBC 10.1-E www.halfen.com 9
HAFEN FRAMING SYSTEMS Information on Dimensioning Heav Dut Medium Dut ight Dut Materials / Statics The HAFEN adjustable assembl sstems can be used in a wide range of industrial fields. It is therefore important that the codes, guidelines and design criteria applicable to each field are considered. The technical values and data for framing channels and bolts in the building industr, mechanical engineering industr and the steel construction industries are eplained respectivel in the following chapters. HAFEN Bolts Framing channels Smbols used for the building industr and their definition F S F S F S F F fle q fle F Permissible load per bolt oad in load and transverse load direction. HAFEN Bolts HS and smooth channels HM Permissible load per bolt oad in load, transverse load and longitudinal direction. HAFEN Bolts HS and toothed channels HZM, HZ, HAFEN Bolts HSR, HZS and smooth channels Permissible load per bolt in longitudinal channel direction Friction coefficient thread/bearing surface μ=0.14; tightening factor 1.6; safet factor 3 Maimum point load- capacit centric load The load carring capacit of the channel lips is decisive. oad figures are onl valid for continuous welded channels or intermittent welds according to the table on page 56. In all other cases suitabilit of the welding seam must be checked. Bending load capacit with span Permissible channel (as a single span element) bending load capacit depends on span distance. imitation of the load capacit determined b bending tension and/or defined deflection. Calculation based on Eurocode 3 Bending load capacit with span Permissible line load of the channel (as a single span element) depends on span distance. imitation of the loading capacit determined b bending tension and/or defined deflection. Calculation based on Eurocode 3 Permissible load in longitudinal channel direction F F Carring capacit of the channels under transverse load angle < 60 Permissible load at a defined angle to the welded on or bolted channels F F Carring capacit of the channels under transverse load angle α 60 F Permissible load at a defined load angle to the welded on or bolted channels F K Fs F K Fs F F fle F Fs q fle Permissible buckling load compression rod Permissible buckling load. Proof based on Eurocode 3 F = (F ² + F ²) F = (F ² + F ²) M M Permissible bending moment of the channel lip Onl applies to welded profiles, otherwise torsion must be taken into account. 10 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Information on Dimensioning When designing an adjustable assembl sstems the eternal load F i must be less or equal to the minimum permissible load of the bolt Fs and to the maimum point load capacit and respectivel to the bending load capacit of the HAFEN Framing channel F. F i MIN (F s ; F ) ( see page 50) Design load i.e. stress calculation: Design load i.e. stress calculation: All load figures are permissible loads. HAFEN Bolts Framing channels Smbols used for mechanical engineering steel construction industr and their definitions F v F R F SZ F F FQ Fv FSZ F FR Pretension force bolt The pre-stress force of the bolt occurs b appling a torque on the bolt and is calculated according to VDI 2230 guidelines. Resulting force The resulting force F R is the vector addition of the eternal loads F in the longitudinal channel direction and the eternal load FQ transverse to the longitudinal channel direction; the resulting force is transferred frictionall to the channel. F R = (F ² + F Q ²) F R,d = 1.4 F (forces) M R,d = 1.4 M (moments) Force in the longitudinal bolt direction The force F SZ works as an eternal load along the screw longitudinal ais and perpendicular to the channel surface and is transferred frictionall to the channel. Maimum Point load-carring capacit centric load The load carring capacit of the channel lips is decisive. oad figures are onl valid for continuous welded channels or intermittent welds according to the table on page 56. In all other cases suitabilit of the welding seam must be checked. F oad capacit of the channels under transverse load angle < 60 Permissible load for a defined angle to the welded or bolted channels. F F F F oad capacit of the channels under transverse load angle α 60 Permissible load for a defined load angle to the welded or bolted channels. Heav Dut Medium Dut ight Dut The force F s along the screw longitudinal ais must be less or equal to the maimum point load capacit of the framing channel F Z. F s F Z The force F Q transverse to the longitudinal channel direction must be less or equal to the load capacit transverse to the longitudinal channel direction of the framing channel F. F Q F NEW! For further technical information and load tables applicable for mechanical engineering see pages 60 65. Materials / Statics 2011 HAFEN MT-FBC 10.1-E www.halfen.com 11
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channels HM 72/48 Heav Dut Medium Dut Materials/ Statics ight Dut HM 72/48 hot-rolled M1:1 Dimensions and load capacities HM 72/48 Material 5 Order-no. 0280. WB 180-00002 180-00003 180-00001 4.5 15.5 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 8.84 11.27 34.97 83.27 14.57 23.13 31.0 32.0 22.3 11.2 7.4 F = maimum bending load capacit on the channel lips 72 33 For further channel data and static properties see page 50 Accessories VUS 72/49 washer 48.5 Double channel on request F HM 72/48 F fle see page 45 12 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts HS 72/48 and HSR 72/48 HS 72/48 Bolt incl. nut Permissible loads for HAFEN Bolts Thread sie Ø permissible load per bolt for standard steel profiles recomm. load per bolt in longitudinal channel direction Grade Grade HS, Grade 4.6 HS, Grade 8.8 HSR, Grade 8.8 Tightening Tightening Tightening 4.6 8.8 torque torque ( = 3) torque [Nm] [Nm] [Nm] Dimensions Thread Thread M 12 M 12 M 16 M 16 M 20 M 20 a b d 62 31 22 Dimensions HS 72/48 and HSR 72/48 ength l oad capacit HS 72/48 HSR 72/48 M 20 M 24 M 27 M 30 M20 50 60 8.8-50 75 8.8 8.8 8.8 100 8.8 8.8 8.8-50 150 8.8 200 permissible load per bolt HS, Grade - 50 for stainless steel recomm. load per bolt in longitudinal channel direction HS, Grade - 50 M 20 27.0 56.4 1.4 120 4.7 400 7.5 400 - - - M 24 38.8 81.2 2.0 200 6.8 680 - - 38.8 2.0 200 M 27 50.5 106.0 2.6 300 8.9 1000 - - - - - M 30 61.7 129.0 3.2 400 10.9 1400 - - - - - Note: do not eceed ma. channel load bearing capacit; see page 12 ocking plates Fs ocking plate GWP 72/48 d b a HSR 72/48 Bolt with nib incl. nut Fs Fs Fs Tightening torque [Nm] Permissible load Thread oad capacit M 12 9.3 M 16 17.3 M 20 22.0 Heav Dut Medium Dut Materials/ Statics ight Dut 2011 HAFEN MT-FBC 10.1-E www.halfen.com 13
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channel HM 52/34 Heav Dut Medium Dut Materials/ Statics ight Dut HM 52/34 hot-rolled M1:1 Dimensions and load bearing capacities HM 52/34 Material 4.1 Order-no. 0280. WB 190-00002 190-00003 190-00001 10.5 52.5 4 22.5 length weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 4.98 6.34 9.33 23.70 5.35 9.03 17.0 21.0 8.8 4.4 2.8 F = maimum bending load capacit on the channel lips For further channel data and static properties see page 50 Accessories HPE 52/34 end cap 33.5 PA - 22 cover F VUS 52/34 Washer Double channel on request F fle bolts see page 17 see page 46 see page 46 see page 45 14 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing s Framing channels HM 50/30 and HM 49/30 HM 50/30 hot-rolled M1:1 2.75 Dimensions and load bearing capacities HM 50/30 and HM 49/30 Material 7.85 HM 50/30 Order-no. 0280. WB 200-00002 200-00003 200-00001 HM 49/30 WB 220-00001 220-00002 A2 220-00003 220-00004 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 3.23 4.12 5.19 13.99 3.24 5.67 11.0 19.0 5.3 2.7 1.6 6070 2.88 3.67 4.18 13.21 2.36 5.29 4.9 46 4.3 2.2 1.2 F = maimum bending load capacit on the channel lips Accessories 49 3 22.5 PA - 41 cover HM 49/30 cold-rolled 3 7.4 HCR version on request VUS 52/34 Washer Double channel on request F SIC 50/30 ocking plate F fle Heav Dut Medium Dut Materials/ Statics ight Dut bolts see page 17 see page 46 see page 45 see page 45 For further channel data and static properties see 50 2011 HAFEN MT-FBC 10.1-E www.halfen.com 15
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channels HM 50/40, H 50/40 and HM 486 Heav Dut Medium Dut Materials/ Statics ight Dut HM and H 50/40 cold-rolled M1:1 Dimensions and load bearing capacities HM 50/40, H 50/40 and HM 486 Material 3 7 Order-no. HM 50/40 0280. WB 090-00002 090-00003 090-00001 H 50/40 0281. WB 100-00001 100-00002 100-00003 HM 486 0280. WB 100-00001 100-00002 49 22 ength Profile weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 3.35 4.27 8.66 15.50 3.97 6.33 5.4 63.0 6.8 3.4 2.3 6000 3.15 3.73 7.14 15.36 3.65 6.27 5.4 53.0 5.7 2.9 1.9 6000 2.31 2.95 2.97 9.62 1.92 4.01 3.5 47.0 3.3 1.7 0.9 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 Accessories 39 HM 486 cold-rolled 2.5 6 48 22 27 F HM 50/40 60 H 50/40 40 18 HM 486 F fle Bolts see page 17 HPE 50/40 end cap PA - 41 cover see page 46 see page 46 16 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts HS 50/30 and HSR 50/30 Permissible loads for HAFEN Bolts Thread sie Ø permissible load per bolt Fs Dimensions HS 50/30 for standard steel profiles recomm. load per bolt in longitudinal channel direction Grade Grade HS, Grade 4.6 HS, Grade 8.8 HSR, Grade 8.8 Tightening Tightening Tightening 4.6 8.8 torque torque ( = 3) torque [Nm] [Nm] [Nm] permissible load per bolt HS, Grade - 50 for stainless steel profiles recomm. load per bolt in longitudinal channel direction HS, Grade - 50 Tightening torque [Nm] M 10 6.4 13.3 0.3 15 1.1 48 - - 6.4 0.3 15 M 12 9.3 19.4 0.5 25 1.6 70 - - 9.3 0.5 25 M 16 17.3 36.1 0.9 60 3.0 200 5.0 200 17.3 0.9 60 M 20 27.0 56.4 1.4 120 4.7 400 7.5 400 27.0 1.4 120 Note: do not eceed ma. channel load bearing capacit; see page 16 ocking plates HS 50/30 HAFEN Bolt incl. nut i = left hand thread HSR 50/30 HAFEN Bolt with nib incl. nut ength l M 10 M 12 M 16 M 20 ength l M 10 M 12 M 16 M 20 30 65-70 -50 75 35-50 40 /8.8 80 /8.8 /8.8 8.8-50 -70-50 45 8.8 /8.8 80 i -50-50 100 /8.8 /8.8 50-50 -70-50 -50 125-50 55 150 /8.8-50 -50-50 60 /8.8 /8.8 8.8 200-50 300 High corrosion resistant stainless steel HAFEN Bolts HS 50/30. Material order grade HCR, on request. Dimensions HSR 50/30 ength l M 10 M 12 M 16 M 20 ength l M 10 M 12 M 16 M 20 40 8.8 60 8.8 8.8 45 8.8 75 8.8 Fs Fs Fs Heav Dut Medium Dut Materials/ Statics ight Dut ocking plate GWP 50/40 ocking plate GWP 50/30 8 12 20 42 21 43.5 Thread M 6 - M 8 M 8 M 10 M 10 M 12 M 12 M 16 M 16 oad capacit Permissible load Thread GWP 50/30 GWP 50/40 M 6 2.2 M 8 4.0 4.0 M 10 6.4 6.4 M 12 9.3 6.4 M 16 9.3 6.4 2011 HAFEN MT-FBC 10.1-E www.halfen.com 17
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channels HM 40/22, HM 40/25 and HM 422 Heav Dut Medium Dut Materials/ Statics ight Dut HM 40/22 hot-rolled M1:1 Dimensions and load bearing capacities HM 40/22 and HM 40/25 Material 2.4 HM 40/22 Order-no. 0280. WB 210-00002 210-00003 210-00001 HM 40/25 WB 230-00001 230-00002 A2 230-00003 230-00004. ength crosssection Profileweight crosssection Dimensions and load bearing capacities HM 422 (C40) Mat. Moment of inertia Moment of resistance Ma. point-load bearing capacit Order-no. 0280. ength weight Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] cm] F fle WB 110-00001 6000 1.55 1.98 1.27 4.29 1.04 2.17 2.5 36.0 1.8 0.9 0.4 110-00002 F = maimum bending load capacit on the channel lips Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 2.10 2.68 1.97 5.87 1.62 2.97 5.7 21.0 2.6 1.3 0.6 6070 2.09 2.66 2.06 6.09 1.39 3.05 3.8 33.0 2.6 1.3 0.6 F = maimum bending load capacit on the channel lips HM 422 (C40) cold-rolled 39.5 M1:1 2.4 21.5 HM 40/25 cold-rolled 2.75 5.6 F HM 40/22 Double channel on request F F fle F fle Accessories VUS 40/25 Washer SIC 40/22 ocking plate see page 45 see page 45 18 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts HS 40/22 and HSR 40/22 32.5 Permissible loads for HAFEN Bolts Thread Ø 32.5 permissible load per T-head bolt Dimensions HS 40/22 ength l M 10 M 12 M 16 ength l M 10 M 12 M 16 Material Material Material Material Material Material 20 80 30-50 -50 80 i -50-50 -70-50 -50 100 40-70 -50-50 -50-50 45 50 125 150-70 -50-50 -50-50 50 i -50 200 60-50 Dimensions HSR 40/22 for standard steel profiles -50 250 300 ength l M 16 ength l M 16 Material Material 40 8.8 60 8.8 recomm. load per T-head bolt in longitudinal channel direction Grade Grade HS, Grade 4.6 HS, Grade 8.8 HSR, Grade 8.8 Tightening Tightening Tightening 4.6 8.8 torque torquet ( = 3) torque [Nm] [Nm] [Nm] permissible load per T-head bolt HS, Grade - 50 for stainless steel profiles recomm. load per T-head boltin longitudinal channel direction HS, Grade - 50 M 10 6.4 13.3 0.3 15 1.1 48 - - 6.4 0.3 15 M 12 9.3 19.4 0.5 25 1.6 70 - - 9.3 0.5 25 M 16 17.3 36.1 0.9 60 3.0 200 5.0 200 17.3 0.9 60 Note: do not eceed ma. channel load bearing capacit; see page 18 ocking plate HS 40/22 HAFEN Bolt incl. nut i = left hand thread HSR 40/22 HAFEN Bolt with nib incl. nut Fs Fs Fs Fs Tightening torque [Nm] Heav Dut Medium Dut Materials/ Statics ight Dut ocking plate GWP 40/22 Dimensions Thread M 6 Thread M 8 M 8 M 10 M 10 a b 35 17 d 10 M 12 M 12 11.5 oad bearing capacit Permissible load Thread oad capacit M 6 2.2 M 8 4.0 M 10 6.4 M 12 9.3 2011 HAFEN MT-FBC 10.1-E www.halfen.com 19
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channels HZM 53/34 Heav Dut Medium Dut Materials/ Statics ight Dut HZM 53/34 hot-rolled, toothed NEW! M1:1 Dimensions and load bearing capacities HZM 53/34 Material 4 Order-no. 0284. WB 070-00002 070-00003 070-00001 4 ength 52.5 22.5 weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 4.63 5.91 9.26 23.23 5.01 8.85 22.0 25 12.5 6.2 2.8 F = maimum bending load capacit on the channel lips For further channel data and static properties see page 50 Accessories PA - 22 cover 34 VUS 52/34 Washer F F fle see page 46 see page 45 20 2011 HAFEN MT-FBC 10.1-E www.halfen.com
l HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts toothed HZS 53/34 NEW! 41.6 Permissible loads for bolts Thread Ø HZS 53/34 HAFEN Bolt, toothed incl. nut for standard steel profiles permissible load per HAFEN Bolt Tightening torque [Nm] HZS Grade 8.8 Dimensions HZS 53/34 ength l M 16 M 20 Material Material 60 8.8-70 65 8.8-70 100 8.8 8.8-70 -70 for stainless steel profiles permissible load per bolt Tightening torque [Nm] HZS Grade -70 M 16 200 36.1 200 23.6 M 20 350 56.4 350 36.8 Note: do not eceed ma. channel load bearing capacit; see pages 20, 56 Fs Fs Fs longitudinal load F s 19.0 Heav Dut Medium Dut Materials/ Statics ight Dut 2011 HAFEN MT-FBC 10.1-E www.halfen.com 21
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channel HZM 38/23 Heav Dut Medium Dut Materials/ Statics ight Dut HZM 38/23 hot-rolled, toothed M1:1 Dimensions and load bearing capacities HZM 38/23 Material 3 Order-no. 0284. WB 060-00001 060-00003 060-00002 38 18 ength 3.5 weight 23 crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 2.42 3.09 2.11 6.17 1.59 3.25 12.0 20 4.2 1.4 0.6 F = maimum bending load capacit on the channel lips For further channel data and static properties see page 50 Accessories VUS 40/25 Washer SIC 38/23 ocking plate HZM 38/23 F F fle see page 45 see page 45 22 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts HZS 38/23, HS 38/23 and HS 38/17 Dimensions HZS 38/23, HS 38/23 and HS 38/17 ength l HZS 38/23 HS 38/23 HS 38/17 ength l HZS 38/23 HS 38/23 HS 38/17 M 12 M 16 M 16 M 10 M 12 M 16 M 12 M 16 M 16 M 10 M 12 M 16 20 70 8.8 25-70 -50 80 8.8 8.8 30 8.8 8.8-50/-70-70 -50/-70 80 i -50-50 -70 A2-70/-70 A2-50/-50 100 8.8 8.8 40 8.8 8.8-50 -50-70 A2-70/-70 A2-50/-50 125 8.8 8.8 50 8.8 8.8 150 8.8 8.8-50 -50-70 A2-70/-70 A2-50/-50 200 8.8 50 i -50-50 -50-50 60 8.8 8.8 /8.8 300 8.8-50/-70 8.8 8.8 High corrosion resistant stainless steel bolts HS 38/17 Material order code HCR, on request. -70-70 -50 Permissible loads for HAFEN Bolts HAFEN Bolts, toothed HZS 38/23 HAFEN Bolts, HS 38/23, HS 38/17 Tightening torque [Nm] HZS, Grade 8.8 permissible load per bolt HZS, Grade -70 longitudinal load F s Tightening torque [Nm] permissible load per bolt HS, Grade 4.6 HS, Grade -50 HS, Grade -70 Thread Ø M 10 - - - 15 6.4 6.4 8.7 M 12 80 19.4 12.6 12.0 25 9.3 9.3 12.6 M 16 120 36.1 23.6 60 17.3 17.3 23.6 Note: do not eceed ma. channel load bearing capacit; see pages 22, 56 Permissible moment load; see page 57 Note: HAFEN Bolts HS are not suitable for loads in direction F S ocking plate HZS 38/23 HAFEN Bolt toothed, incl. nut Fs Fs HS 38/23 HAFEN Bolt, incl. nut HS 38/17 HAFEN Bolt, incl. nut i = eft hand thread Fs Heav Dut Medium Dut Materials/ Statics ight Dut ocking plate GWP 38/17 d b a Dimensions Thread Thread M 6 M 6 M 8 M 8 M 10 M 10 M 12 M 12 a b d 33.5 17.5 6 oad bearing capacit Permissible load Thread oad capacit M 6 2.2 M 8 4.0 M 10 5.7 M 12 5.7 2011 HAFEN MT-FBC 10.1-E www.halfen.com 23
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channel HZM 29/20 Heav Dut Medium Dut Materials/ Statics ight Dut HZM 29/20 hot-rolled, toothed M1:1 Dimensions and load capacities HZM 29/20 Material 2.5 Order-no. 0284. WB 050-00001 050-00003 29 14 2.5 ength 20 weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 1.51 1.98 1.02 2.42 0.91 1.67 8.0 15 2.4 0.7 0.3 F = maimum bending load capacit on the channel lips For further channel data and static properties see page 50 Accessories US DIN 9021 Washer SIC 29/20 ocking plate HZM 29/20 F F fle see page 44 see page 45 24 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts HZS 29/20, HS 28/15 and HS 29/20 Dimensions HZS 29/20, HS 29/20 and HS 28/15 ength l HZS 29/20 HS 29/20 HS 28/15 ength l HZS 29/20 HS 29/20 HS 28/15 M 12 M 12 M 6 M 8 M 10 M 12 M 12 M 12 M 6 M 8 M 10 M 12 15 60 8.8 20-70 A2-70/-70 80 8.8 25-70 A2-70 100 8.8-70 -50 30 8.8 125 8.8-50 A2-70/-70 A2-70/-70 150 8.8 40 8.8-50 8.8 200 8.8 A2-70/-70-50 50 8.8 250 8.8 300 8.8 50 i A2-70/-70-50 High corrosion resistant stainless steel bolts HS 38/17, Material order reference HCR. Permissible load for HAFEN Bolts HAFEN Bolt toothed HZS 29/20 HAFEN Bolt HS 28/15, HS 29/20 Tightening torque [Nm] permissible load per HAFEN Bolt HZS, Grade 8.8 longitudinal load F s Tightening torque [Nm] permissible load per HAFEN Bolt HS, Grade 4.6 HS, Grade -50 HS, Grade -70 Thread Ø M 6 - - 3 2.2 - - M 8 - - 8 4.0 4.0 5.5 8.0 M 10 - - 15 6.4 6.4 8.7 M 12 80 19.4 25 9.3 - - Note: do not eceed ma. channel load bearing capacit; see pages 24, 56 Permissible moment load; see page 57 Note: HAFEN Bolts HS are not suitable for loads in direction F S ocking plate HZS 29/20 HAFEN Bolt toothed incl. nut Fs Fs HS 28/15 HAFEN Bolt, incl. nut HS 29/20 HAFEN Bolt, incl. nut Fs Heav Dut Medium Dut Materials/ Statics ight Dut ocking plate GWP 28/15 d Assembl note: M 6 and M 8: Insert locking plate at a slant through the channel slit. M 10: First insert the locking plate then screw in the threaded rod b a Dimensions Thread Thread M 6 M 6 M 8 M 8 a b d 24.5 13.0 4 M 10 M 10 33.5 17.5 5 oad bearing capacit Permissible oad Thread oad capacit M 6 1.9 M 8 2.8 M 10 3.0 2011 HAFEN MT-FBC 10.1-E www.halfen.com 25
HAFEN FRAMING SYSTEMS Framing s Heav Dut Framing Sstem Framing channel HZ 63/63 Heav Dut Medium Dut Materials/ Statics ight Dut HZ 63/63 cold-rolled, toothed M1:1 Dimensions and load bearing capacities HZ 63/63 Material 3 2.5 Order-no. 0283. 7 ength 030-00001 3000 030-00003 6000 63 9.5 22 9.5 weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle F = maimum bending load capacit on the channel lips For further channel data and static properties see page 52 Accessories HAFEN Bolts and locking plates HZS 41/41, HZS 41/22, GWP 41/41, GWP 41/22 63 toothing HZ 63/63 6.35 7.09 33.07 42.95 10.06 13.63 5.6 134.0 16.5 8.2 5.5 HPE 63/63 end caps F 250 Base channel for HAFEN Powerclick Sstem 63. Information about the Powerclick assembl sstem can be found in our product catalogue "HAFEN Powerclick Technical Product Information PC63". PA - 41 cover F fle 28 14 see medium dut framing sstem HAFEN see pages 34,35 see page 46 see page 46 26 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem Framing channel HM 41/41 and H 41/41 HM 41/41 and H 41/41 cold-rolled M1:1 Dimensions and load capacities HM 41/41 and H 41/41 Material 2.5 7 Order-no. HM 41/41 0280. WB 080-00001 SV 080-00002 080-00003 080-00004 H 41/41 0281. WB 010-00001 SV 010-00003 010-00002 010-00004 HM 41/41 D 0280. WB 150-00001 150-00003 150-00002 41 22 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 41 HM 41/41 2.61 3.33 7.16 9.22 3.06 4.46 5.6 49.0 5.4 2.7 1.8 2.46 2.98 6.07 9.16 2.84 4.43 5.6 42.0 4.7 2.3 1.6 5.33 6.67 35.81 18.44 8.67 8.93 5.6 132.0 H 41/41 50 28 14 F HM 41/41 D Double channel on request F fle 1.0 m 1.5 m 2.0 m 7.3 4.9 3.7 Heav Dut Medium Dut Materials/ Statics ight Dut Accessories HPE 41/41 end cap PA - 41 cover see page 46 see page 46 2011 HAFEN MT-FBC 10.1-E www.halfen.com 27
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem Framing channel HZM 41/41 and HZ 41/41 Heav Dut Medium Dut Materials/ Statics ight Dut HZM 41/41 and HZ 41/41 cold-rolled, toothed M1:1 Dimensions and load capacities HZM 41/41 and HZ 41/41 Material 2.5 7 Order-no. HZM 41/41 0284. WB 010-00001 010-00002 010-00003 HZ 41/41 0283. WB 010-00001 010-00002 010-00003 HZM 41/41 D 0284. 41 22 WB 030-00001 030-00002 030-00003 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 41 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 Accessories HZM 41/41 2.63 3.25 6.91 9.10 2.91 4.41 5.6 47.0 5.2 2.6 1.7 2.46 2.90 5.87 9.04 2.69 4.38 5.6 41.0 4.5 2.3 1.1 5.11 6.51 33.74 18.38 8.16 8.90 5.6 126.0 HZ 41/41 50 28 F 14 HZM 41/41 D F fle 1.0 m 1.5 m 2.0 m 6.9 4.6 3.5 HPE 41/41 end cap PA - 41 cover see page 46 see page 46 28 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem Framing channel HM 41/62 and H 41/62 HM 41/62 and H 41/62 cold-rolled M1:1 Dimensions and load capacities HM 41/62 and H 41/62 Material 2.5 7 Order-no. HM 41/62 0280. WB 140-00002 SV 140-00001 140-00003 H 41/62 0281. WB 040-00001 SV 040-00003 040-00002 HM 41/62 D 0280. WB 170-00001 170-00002 ength weight crosssectiont Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 1 m 2 m 3 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 F = maimum bending load capacit on the channel lips Accessories 41 22 62 HM 41/62 3.42 4.36 20.18 13.10 5.92 6.35 5.6 92.0 5.1 2.6 1.5 3.14 3.99 17.27 13.03 5.47 6.31 5.6 81.0 4.5 2.2 1.3 6.84 8.72 108.11 26.21 17.45 12.69 5.6 269.0 H 41/62 Note for span distance : take constructive measures to prevent possible bulging, tilting or buckling. 50 28 F 14 HM 41/62 D For further channel data and static properties see pages 50, 52 F fle 1.0 m 1.5 m 2.0 m 14.8 9.9 7.4 Heav Dut Medium Dut Materials/ Statics ight Dut PA - 41 cover see page 46 2011 HAFEN MT-FBC 10.1-E www.halfen.com 29
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem Framing channels HM 41/83 and H 41/83 Heav Dut Medium Dut Materials/ Statics ight Dut HM 41/83 and H 41/83 cold-rolled Dimensions and load capacities HM 41/83 and H 41/83 Material Order-no. HM 41/83 0280. WB 130-00002 SV 130-00001 130-00003 H 41/83 0281. WB 030-00004 SV 030-00006 030-00005 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 1 m 2 m 3 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 F = maimum bending load capacit on the channel lips Accessories HM 41/83 H 41/83 50 28 14 M1:1 2.5 7 41 22 4.23 5.39 42.50 17.00 9.52 8.23 5.6 148.0 8.2 4.1 2.7 3.93 5.02 37.07 16.93 8.85 8.20 5.6 133.0 7.3 3.7 2.4 83 Note for span distance : take constructive measures to prevent possible bulging, tilting or buckling. For further channel data and static properties see pages 50, 52 F F fle PA - 41 cover see page 46 30 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem Framing channels HM 41/22 and H 41/22 HM 41/22 and H 41/22 cold-rolled M1:1 Dimensions and load bearing capacities HM 41/22 and H 41/22 Material 2.5 7 Order-no. HM 41/22 0280. WB 120-00001 SV 120-00002 120-00003 120-00004 H 41/22 0281. 41 22 WB 020-00001 SV 020-00003 020-00002 020-00004 HM 41/22 D 0280. WB 160-00001 160-00002 160-00003 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 21 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 Accessories HM 41/22 1.80 2.30 1.19 5.32 0.97 2.58 5.6 15.0 1.8 0.8 0.4 1.57 1.95 0.99 5.27 0.89 2.55 5.6 12.0 1.6 0.7 0.3 3.60 4.59 5.55 10.64 2.69 5.15 5.6 42.0 H 41/22 50 28 14 F HM 41/22 D F fle 1.0 m 1.5 m 2.0 m 2.3 1.5 0.9 Heav Dut Medium Dut Materials/ Statics ight Dut HPE 41/41 end cap PA - 41 cover see page 46 see page 46 2011 HAFEN MT-FBC 10.1-E www.halfen.com 31
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem Framing channels HZM 41/22 and HZ 41/22 Heav Dut Medium Dut Materials/ Statics ight Dut HZM 41/22 and HZ 41/22 cold-rolled, toothed M1:1 Dimensions and load bearing capacities HZM 41/22 and HZ 41/22 Material 2.5 7 Order-no. HZM 41/22 0284. WB 020-00001 020-00002 020-00003 HZ 41/22 0283. WB 020-00001 020-00002 020-00003 HZM 41/22 D 0284. 41 22 WB 040-00001 040-00002 040-00003 ength 21 weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 1.79 2.22 1.16 5.21 0.92 2.52 5.6 14.0 1.7 0.8 0.3 6000 1.57 1.87 0.97 5.15 0.86 2.49 5.6 12.0 1.5 0.6 0.3 6070 3.58 4.66 5.64 11.00 2.68 5.33 5.6 42.0 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 Accessories HZM 41/22 HZ 41/22 50 28 F 14 HZM 41/22D F fle 1.0 m 1.5 m 2.0 m 2.3 1.5 0.9 HPE 41/41 end cap PA - 41 cover see page 46 see page 46 32 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem Framing channels H 41/41 and H 41/22 H 41/41 cold-rolled M1:1 1.5 Dimensions and load capacities H 41/41 and H 41/22 Material 7.5 Order-no. H 41/41 0282. SV 010-00002 H 41/22 0282. SV 020-00003 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 F = maimum bending load capacit on the channel lips Accessories 41 22 41 H 41/22 cold-rolled 1.5 7 41 22 21 H 41/41 H 41/22 1.61 1.92 4.24 6.10 2.04 2.95 1.8 91.0 3.2 1.6 1.0 1.14 1.33 0.75 3.67 0.71 1.78 1.8 31.0 1.1 0.4 0.2 F 50 28 50 14 28 F fle 14 Heav Dut Medium Dut Materials/ Statics ight Dut HPE 41/41 HPE 41/22 end cap PA - 41 cover see page 46 see page 46 2011 HAFEN MT-FBC 10.1-E www.halfen.com 33
HAFEN FRAMING SYSTEMS Framing s Medium Dut Framing Sstem HAFEN Bolts HZS 41/41, HZS 41/22 and HS 41/41 Heav Dut Medium Dut Materials/ Statics ight Dut HAFEN Bolts for all 41er profiles: Dimensions HZS 41/41, HZS 41/22 and HS 41/41 ength l HZS 41/41 HZS 41/22 HS 41/41 M6 M8 M10 M12 M16 M12 M16 M10 M12 30 inc flake coated inc flake coated inc flake coated inc flake coated 35 8.8-50 4.6 4.6 50 inc flake coated inc flake coated inc flake coated 63 inc flake coated 75 inc flake coated inc flake coated 80-50 -50-50 -50 8.8 8.8 4.6-50 -50 100 inc flake coated 8.8 102 inc flake coated Permissible loads for bolts Thread Ø 34.5 Tightening torque [Nm] l HAFEN Bolts toothed HZS 41/41 HAFEN Bolts toothed HZS 41/22 HAFEN Bolts HS 41/41 permissible load per T-head bolt permissible load per T-head bolt recomm. load per T-head bolt all channels F s HZS 41/41 HAFEN Bolts toothed (order nut separatel) Fs Fs Fs Fs Fs Fs HM/ H F s HZM/ HZ F s Tightening torque [Nm] H F s Tightening torque Grade 8.8 (Grade ) [Nm] all channels Grade 8.8 F s HZM/ HZ Grade 8.8 F s all channels Grade -50 F s HM/ H Grade -50 F s HZM/ HZ Grade -50 F s Tightening torque [Nm] HM/H Grade 4.6 F s HM/H Grade 4.6 F s HM/H Grade -50 F s M 6 12 5.0 1.0 2.2 12 1.0 - - - - - - - - - - - M 8 28 6.0 2.4 4.0 28 2.4 - - - - - - - - - - - M 10 55 7.0 3.5 5.0 55 3.5 - - - - - - 15 (15) 6.4 0.3 6.4 0.3 M 12 60 7.0 4.0 5.0 55 3.6 50 (50) 7.0 5.0 7.0 1.7 5.0 25 (25) 9.3 0.5 9.3 0.5 M 16 125 12.0 7.5 7.5 95 4.5 80 (80) 12.0 7.5 12.0 4.0 5.0 - - - - - Note: do not eceed ma. channel load bearing capacit; see pages 27 33 and 56 Application notes: HZS 41/41: - M16 not for channels 41/22 - M16 can onl be mounted b sliding on at channel end - M16 102 without toothing, F S = 4.0 kn 34.5 l HZS 41/22 HAFEN Bolts toothed, incl. nut for toothed Profiles 41/41 and 41/22 l 35.2 HS 41/41 HAFEN Bolts, incl. nut HM/H Grade -50 F s 34 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS ocking Plates Medium Dut Framing Sstem ocking plates GWP 41/41 - SN, - SH, GWP 41/22 ocking plates GWP 41/41 ocking plates for all 41er Profiles and Profile 63/63 Dimensions GWP 41/41 Thread oad bearing capacit GWP 41/41, - SN, -SH Thread Ø Thread Thread all Profiles F S d M 6 M 6 6 M 8 M 8 M 8 8 / 6 M 10 M 10 M 10 F M12 F M12 F M12 M12 M12 12 b 20 M16 M16 12 30 Tightening torque [Nm] a 34.5 HM/H F S Dimensions GWP 41/41 SN Thread d M 6 6 M 8 8 M 10 F M 12 HZM/HZ F S 9 Tightening torque [Nm] b a 20 34.5 H F S HM/H F S Tightening torque [Nm] HM/H F S M 6 5.0 12 1.0 2.2 12 1.0 5.0 6.5 0.3 2.2 M 8 6.0 28 2.4 4.0 28 2.4 6.0 16 0.6 4.0 M 10 7.0 55 3.5 5.0 55 3.5 7.0 31.5 1.2 5.0 M 12 9.0 75 5.0 5.0 55 3.6 - - - - F M12 7.0 60 4.0 5.0 55 3.6 7.0 55 1.7 5.0 M16 12.0 125 7.5 7.5 95 4.5 12.0 125 4.0 5.0 ocking plate GWP 41/22 Dimensions GWP 41/22 Thread Thread d d 9 b d b a b a a ocking plates GWP 41/41 SN ocking plates with short spring for Profiles 41/22 and 63/63 Application notes: GWP 41/41: - M12 + M16 not for channels 41/22 and 63/63 - M16 can onl be mounted b sliding on at channel end F s ocking plate for toothed channels 41/22 and 41/41 oad bearing capacit GWP 41/22 d a F s b ocking plates GWP 41/41 SH ocking plates with long spring for Profile 41/41 Dimensions GWP 41/41 SH Thread d M 6 6 M 8 8 M 10 9 M 12 12 d b a b a 20 34.5 F s F s HZM/HZ F S Heav Dut Medium Dut Materials/ Statics ight Dut M 6 - M 8 M 8 M 10 M 10 M 12 M 12 M 16 M16 On request 7.5 20 34.5 Thread Ø F S Tightening torque [Nm] HZM/HZ F S HM/H F S Tightening torque [Nm] HM/H F S HZM/HZ F S M 6 5.0 12 1.0 - - - - M 8 6.0 28 2.4 6.0 16-4.0 M 10 7.0 55 3.5 7.0 31.5-5.0 M 12 9.0 50 3.6 7.0 50-5.0 M 16 7.0 80 4.5 7.0 80-5.0 2011 HAFEN MT-FBC 10.1-E www.halfen.com 35
HAFEN FRAMING SYSTEMS Framing s ight Dut Framing channels HM 36/36, H 36/36 and HM 38/17 Accessories Medium Dut Framing s Heav Dut Materials/ Statics ight Dut HM 36/36 and H 36/36 cold-rolled M1:1 Dimensions and load capacities HM 36/36, H 36/36, HM 38/17 Material 2.5 Order-no. HM 36/36 0280. WB 070-00001 070-00002 070-00003 H 36/36 0281. WB 050-00001 050-00002 050-00003 HM 38/17 0280. 36 18 WB 020-00001 020-00002 A2 020-00003 020-00004 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit t Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 36 2.19 2.79 4.51 5.85 2.18 3.25 4.4 44.0 3.9 1.9 1.3 2.00 2.42 3.65 5.78 1.97 3.21 4.4 36.0 3.2 1.6 1.1 6070 1.81 2.30 0.85 4.29 0.82 2.26 4.8 11.0 1.5 0.6 0.3 F = maimum bending load capacit on the channel lips Accessories PA - 18H cover HM 38/17 cold-rolled 3 38 18 HPE 36/36 end cap for HM 36/36 and H 36/36 17.5 HCR version on request F HM 36/36 H 36/36 60 15 40 HM 38/17 For further channel data and static properties see pages 50, 52 SIC 38/17 ocking plate F fle see page 46 see page 46 see page 45 36 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts HS 38/17 Permissible loads for bolts Thread Ø permissible load per HAFEN Bolt for standard steel profiles recomm. load per bolt in longitudinal channel direction Grade Grade HS, Grade 4.6 HS, Grade 8.8 Tightening Tightening 4.6 8.8 torque torque [Nm] [Nm] permissible load per HAFEN Bolt HS, Grade A2/ - 50 for stainless steel profiles HS, Grade A2/ - 70 recomm. load per bolt in longitudinal channel direction HS, Grade A2/ - 50/70 Tightening torque [Nm] M 10 6.4 13.3 0.3 15 1.1 48 6.4 8.7 0.3 15 M 12 9.3 19.4 0.5 25 1.6 70 9.3 12.6 0.5 25 M 16 17.3 36.1 0.9 60 3.0 200 17.3 23.6 0.9 60 Note: do not eceed ma. channel load bearing capacit; see page 36 ocking plates HS 38/17 HAFEN Bolts incl. nut i = with left hand thread Fs Dimensions HS 38/17 ength l ength l M 10 M 12 M 16 M 10 M 12 M 16 20 60 25-70 -50 8.8 30-70 -70-50 70 8.8-70 A2-70 A2-50 80-70 -50-70 -50 40 80i -50-50 100-70 A2-70 A2-50 -70-50 -50-50 50 125 150-70 A2-70 A2-50 -50-50 -70-50 200 50i -50-50 -50-50 High corrosion resistant stainless steel bolts HS 38/17, Material order code HCR, on request. Fs Fs Fs Heav Dut Medium Dut Materials/ Statics ight Dut ocking plates GWP 38/17 Dimensions Thread Thread M 6 M 6 M 8 M 8 M 10 M 10 M 12 M 12 a b d 33.5 17.5 6 oad bearing capacit Permissible load Thread oad capacit M 6 2.2 M 8 4.0 M 10 5.7 M 12 5.7 2011 HAFEN MT-FBC 10.1-E www.halfen.com 37
HAFEN FRAMING SYSTEMS Framing s ight Dut Framing channels HM 28/28 and H 28/28 Accessories Medium Dut Framing s Heav Dut Materials/ Statics ight Dut HM 28/28 and H 28/28 cold-rolled M1:1 Dimensions and load capacities HM 28/28 and H 28/28 Material 2 Order-no. HM 28/28 0280. WB 050-00001 SV 050-00003 050-00002 050-00004 H 28/28 0281. 12 WB 060-00001 SV 060-00003 060-00002 060-00004 27 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 28 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 Accessories HPE 28/28 end cap HM 28/28 H 28/28 1.36 1.73 1.70 2.01 1.08 1.49 3.0 31.0 1.9 0.9 0.5 1.22 1.48 1.33 1.98 0.95 1.47 3.0 25.5 1.5 0.8 0.4 40 25 12.5 12,5 F F fle see page 46 38 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Framing s ight Dut Framing channels HM 26/26 and H 26/26 HM 26/26 and H 26/26 cold-rolled M1:1 Dimensions and load capacities HM 26/26 and H 26/26 Material 1.25 Order-no. HM 26/26 0280. SV 040-00001 H 26/26 0281. 26 12 SV 070-00001 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 26 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 Accessories HPE 26/26 end cap HM 26/26 H 26/26 40 0.82 1.05 0.94 1.18 0.64 0.91 1.10 50.0 1.1 0.5 0.3 0.72 0.89 0.73 1.16 0.56 0.89 1.10 40.0 0.9 0.4 0.22 25 12.5 12,5 F F fle Heav Dut Medium Dut Materials/ Statics ight Dut see page 46 2011 HAFEN MT-FBC 10.1-E www.halfen.com 39
HAFEN FRAMING SYSTEMS Framing s ight Dut Framing channel HM 28/15, H 28/15 and HM 315 (C30) Accessories Medium Dut Framing s Heav Dut Materials/ Statics ight Dut HM 28/15 and H 28/15 cold-rolled M1:1 Dimensions and load capacities HM 28/15, H 28/15, HM 315 (C30) Material 2.25 Order-no. HM 28/15 0280. WB 010-00001 010-00002 A2 010-00004 070-00003 H 28/15 0281. WB 080-00001 080-00004 A2 080-00002 080-00003 28 12 ength weight crosssection Dimensions and load bearing capacities HM 315 (C30) Mat. Moment of inertia Moment of resistance Ma. point-load bearing capacit Order-no. 0280. ength Moment of weight crosssection inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle WB 060-00001 6000 0.77 0.97 0.30 1.26 0.32 0.84 1.66 17.7 0.59 0.16 0.07 060-00002 F = maimum bending load capacit on the channel lips Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6070 15.25 F = maimum bending load capacit on the channel lips HM 315 (C30) cold-rolled M1:1 1.5 30 16 15 HM 315 HM 28/15 H 28/15 1.09 1.39 0.41 1.45 0.46 1.03 3.9 8.2 0.8 0.3 0.12 0.86 1.16 0.32 1.35 0.40 0.98 3.9 7.0 0.7 0.22 0.10 40 HCR version on request 25 F 9 F F fle F fle Accessories SIC 38/17 ocking plate see page 45 For further channel data and static properties see pages 50, 52 40 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolt HS 28/15 Permissible loads for HAFEN Bolts for standard steel profiles permissible load per HAFEN Bolt Dimensions HS 28/15 ength l M 6 M 8 M 10 M 12 ength l M 6 M 8 M 10 M 12 15 50 20 A2-70 A2-70 -70-70 25 60 A2-70 -70-70 80 30-70 100 A2-70 A2-70 -50-70 -70 125 40-50 8.8 150 A2-70 -50-70 200 50 i -50-50 High corrosion resistant stainless steel HAFEN Bolts HS 28/15, Material order code HCR, on request. recomm. load per HAFEN Boltin longitudinal channel direction Dimensions Thread Thread M 6 M 6 M 8 M 8 a permissible load per HAFEN Bolt b d 24.5 13.0 4 M 10 M 10 33.5 17.5 5 for stainless steel profiles recomm. load per HAFEN Boltin longitudinal channel direction Thread Ø Grade 4.6 HS, Grade 4.6 Tightening torque [Nm] HS, Grade A2/ - 50 HS, Grade A2/ - 70 HS, Grade A2/ - 50/70 Tightening torque [Nm] M 6 2.2 0.1 3 2.2 3.0 0.1 3 M 8 4.0 0.2 8 4.0 5.5 0.2 8 M 10 6.4 0.3 15 6.4 8.7 0.3 15 M 12 9.3 0.5 25 9.3 12.6 0.5 25 Note: do not eceed ma. channel load bearing capacit. see page 40 ocking plates HS 28/15 HAFEN Bolt incl. nut i = with left hand thread (not for HM 315) ocking plates GWP 28/15 for Profiles 28/15 and 315 (C30) Fs Fs Fs oad bearing capacit Permissible load Thread oad capacit M 6 1.9 M 8 2.8 M 10 3.0 Installation note: M 6 and M 8: Insert locking plate at a slant through the channel slit. M 10: First insert the locking plate then screw in the threaded rod. Fs Heav Dut Medium Dut Materials/ Statics ight Dut 2011 HAFEN MT-FBC 10.1-E www.halfen.com 41
HAFEN FRAMING SYSTEMS Framing s ight Dut Framing channels HM 20/12 and H 20/12 Accessories Medium Dut Framing s Heav Dut Materials/ Statics ight Dut HM 20/12 and H 20/12 cold-rolled M1:1 Dimensions and load bearing capacities HM 20/12 and H 20/12 Material 1.5 20 10 Order-no. HM 20/12 0280. WB 030-00001 030-00003 A2 030-00002 H 20/12 0281. WB 090-00001 090-00002 A2 090-00003 12 ength weight crosssection Moment of inertia Moment of resistance Ma. point-load bearing capacit Bending load capacit for span [m] G A I I W W F 0.5 m 1 m 1.5 m [kg/m] [cm²] [cm 4 ] [cm 4 ] [cm³] [cm³] [cm] F fle 6000 F = maimum bending load capacit on the channel lips For further channel data and static properties see pages 50, 52 Accessories SIC 20/12 ocking plate HM 20/12 H 20/12 40 0.52 0.66 0.12 0.36 0.16 0.36 2.24 5.8 0.3 0.08 0.04 0.45 0.53 0.09 0.35 0.14 0.36 2.24 4.6 0.23 0.06 0.03 25 9 F F fle SIC see page 45 42 2011 HAFEN MT-FBC 10.1-E www.halfen.com
l HAFEN FRAMING SYSTEMS HAFEN Bolts and Accessories HAFEN Bolts HS 20/12 Permissible loads for bolts Thread Ø 15.5 permissible load per HAFEN Bolt Grade 4.6 for standard steel profiles HS, Grade 4.6 Dimensions HS 20/12 permissible load per HAFEN Bolt in longitudinal channel direction ength l M 6 M 8 15 20 A2-70 25 30 A2-70 40 A2-70 50 A2-70 60 80 100 Tightening torque [Nm] Dimensions Thread Thread a permissible load per HAFEN Bolt HS, Grade A2-70 b d for stainless steel profiles permissible load per HAFEN Bolt in longitudinal channel direction HS, Grade A2-70 oad bearing capacit Tightening torque [Nm] M 6 2.2 0.1 3 3.0 0.1 3 M 8 4.0 0.2 8 5.5 0.2 8 Note: do not eceed ma. channel load bearing capacit see page 42 ocking plates HS 20/12 HAFEN Bolts incl. nut Fs ocking plates GWP 20/12 Fs Fs Fs permissible load Thread oad capacit Heav Dut Medium Dut Materials/ Statics ight Dut M 5 M 5 M 6 M 6 16 9 4 M 5 1.5 M 6 1.9 2011 HAFEN MT-FBC 10.1-E www.halfen.com 43
HAFEN FRAMING SYSTEMS Threaded Rods, Heagon Head Bolts, Nuts, Washers Heav Dut Medium Dut ight Dut GWS Threaded rod DIN 976-1 HSK He. head bolt DIN 933 or DIN EN ISO 4017 (without nut) He. head bolts are used in combination with HAFEN locking plates FK 4.6 Thread Stainless steel Thread ength oad capacit M 6 M 6 1000 2.2 M 8 M 8 1000 4.0 M 10 M 10 1000 6.4 M 12 M 12 1000 9.3 M 16 M 16 1000 17.3 M 20 M 20 1000 27.0 M 24 1000 38.8 Order eample: GWS - M 12 1000 - FK 8.8 Dimensions Stainless steel Dimensions S DIN S EN M 6 12 10 10 M 6 25 M 8 25 M 8 25 M 8 40 M 10 20 M 10 30 M 10 30 M 10 45 M 10 45 M 10 60 M 10 70 M 12 22 M 12 25 M 12 25 M 12 30 M 12 30 M 12 40 M 12 40 M 12 50 M 12 60 M 12 60 M 12 80 M 12 80 M 12 90 M 16 40 M 16 40 M 16 60 M 16 60 M 16 90 M 16 90 13 13 17 16 19 18 24 24 US Washers DIN EN ISO 7093-1/7094, DIN 440 US Washers DIN 125/ DIN EN ISO 7089 DIN EN for Screw sie Stainless steel for Screw sie D d s 7094 M 6 22 6.6 2 7093-1 M 8 M 8 24 8.4 2 7093-1 M 10 M 10 30 10.5 2.5 7094 M 12 45 13.5 4 7093-1 M 12 M 12 37 13 3 7093-1 M 16 M 16 50 17 3 7094 M 20 72 22 6 Order eample: US - M 12 - - DIN EN ISO 7093-1 Stainless D d s steel for Screw sie for Screw sie M 6 M 6 12 6.4 1.6 M 8 M 8 16 8.4 1.6 M 10 M 10 21 10.5 2 M 12 M 12 24 13 2.5 M 16 M 16 30 17 3 M 20 M 20 37 21 3 M 24 M 24 44 25 4 Stainless steel A2 D d s for Screw sie for Screw sie M 8 17 8.4 1.6 M 10 M 10 21 10.5 2 M 12 M 12 24 13 2.5 M 16 M 16 30 17 3 Order eample: US - - M 12 - DIN 125 Materials/ Statics MU He. head bolt DIN 934 or DIN EN ISO 4032 Stainless S/m S/m e FK 8 steel DIN ISO DIN Thread Thread M 6 M 6 10/5 10/5 11.5 M 8 M 8 13/6.5 13/6.5 15.0 M 10 M 10 17/8 16/ 8 19.6 M 12 M 12 19/10 18/10.5 21.9 M 16 M 16 24/13 24/14.5 27.7 M 20 M 20 30/16 30/18 34.6 M 24 M 24 36/19 36/21 41.5 Stainless S/m S/m e steel A2 DIN EN Thread Thread M6, M8 M 8 13/6.5 13/6.5 15.0 M 10 M 10 17/08 16/ 8 19.6 M 12 M 12 19/10 18/10.5 21.9 M 16 M 16 24/13 24/14.5 27.7 HJV Adapter coupler Stainless t b d F steel Tpe Tpe 1 1 6 40 13 1.5 2 2 8 50 17 3.3 3 3 10 50 17 5.0 recommended. ma. load Cross-section 44 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Couplers, Ring Nuts, Square Washers VBM Coupler, round SKM Heagonal rod coupler with view hole SPH Turnbuckle (right and lefthand thread) f = min. Screw-in depth M12 = 10 mm M16 = 13 mm SIC ocking plate thread sie Stainless steel thread sie D load capacit M 6 M 6 10/10 15 2.2 M 8 M 8 12/14 20 4.0 M 10 M 10 13/16 25 6.4 M 12 M 12 16/20 30 9.3 M 16 M 16 21/25 40 17.3 M 20 M 20 26/32 50 27.0 Recomm. maimum working load at centric-pull Sie D for tpe / thread sie Stainless steel thread sie S load capacit M 10 M 10 13 40 6.4 M 12 M 12 17 40 9.3 M 16 M 16 22 50 17.3 Recomm. maimum working load at centric-pull Order eample: SKM - - M 12 Stainless steel Thread M 12 ength Stainless steel Thread M 16 ength D for M12 D for M16 M12 60 M16 60 16 22 M12 75 M16 75 16 22 M12 95 M16 95 16 22 M12 115 M16 115 16 22 M12 135 M16 135 16 22 perm. load: 5 kn perm. load: 10 kn Order eample: SPH - - M 12 75 Article description Stainless steel Article description for HAFEN Bolt Tpe Dimensions SIC - 50/30 - SIC - 50/30-50/30 M16, M20 SIC - 40/22 - SIC - 40/22-38/17 40/22 M16 SIC - 38/23-38/23 M16 SIC - 29/20-29/20 M12 SIC - 38/17 - SIC - 38/17-38/17 40/22 M12, M10 SIC - 28/15 - SIC - 28/15-28/15 M8, M10 SIC - 20/12 - SIC - 20/12-20/12 M8 Order eample: SIC - 38/17- RM Ring-nut (DIN 582 Issue date 2003-8) VUS square - washers VUS 40/25 for profiles 40/25; HZA 41/22 VUS 49/30 for profiles 54/33, 49/30 VUS 52/34 for profiles 52/34, 50/30 VUS 72/49 for profiles 72/48, 72/49 VUS 41/41 for all 41 profiles d load capacit C 15 E thread sie M 8 20 1.4 M 10 25 2.3 M 12 30 3.4 M 16 35 7.0 M 20 40 12.0 Recomm. maimum working load at centric-pull according to DIN 582 a b d for bolts Stainless steel for bolts M 10 M 10 40 40 5 M 12 M 12 40 40 5 M 16 M 16 40 40 5 M 10 M 10 37 37 5 M 12 M 12 37 37 5 M 16 M 16 37 37 5 M 20 M 20 37 37 5 M 16 M 16 50 50 6 M 20 M 20 50 50 6 M 20 M 20 54 54 6 M 24 M 24 54 54 6 M 27 M 27 54 54 6 M 30 M 30 54 54 6 M 6 M 6 40 40 6 M 10 M 10 40 40 6 M 12 M 12 40 40 6 Order eample: VUS 52/34 - - M 20 Heav Dut Medium Dut ight Dut Materials/ Statics Application: Assembl Diagram: To prevent bolts HAFEN turning during assembl. HAFEN Bolt ocing plate SIC 2011 HAFEN MT-FBC 10.1-E www.halfen.com 45
HAFEN FRAMING SYSTEMS End Caps, Cover Strip Heav Dut Medium Dut ight Dut end caps, HPE end caps in plastic HAFEN cover PA Tpe HPE 63/63 color: blue Tpe HPE color: black Tpe HPE 41/41 Tpe HPE 41/22 color: black Order no. Description Order-no. For 0318.000- HPE 63/63 00010 63/63 HPE 52/34 00001 52/34 HPE 50/40 00002 50/40 HPE 41/41 00003 41/41 HPE 41/22 00004 41/22 HPE 36/36 00005 36/36 HPE 28/28 00006 28/28 HPE 28/15 00011 28/15 HPE 26/26 00007 26/26 The channel cover PA is used to prevent dirt entering the channel slit. Tpe overview Tpe: PA 41 PA 22 PA 18 H Assembl diagram: Tpe HPE 63/63 Tpe HPE 41/41 Tpe HPE 41/22 Assembl diagram: 15 PA 22 HAFEN Tpe HPE Materials/ Statics Qualit: hard PVC (KS) 41 21 9 27.5 22 15 27.5 16.5 5 HAFEN for eample; HM 52/34 Order-no. Tpe length Order -no. 0321.000- PA - 41 - KS - 3000 00002 white medium gra medium gra PA - 41 - SV - 3000 00001 Qualit: Steel sendimirgalvanied (SV) 9 41 21 suitable for profiles: 50/40, 50/30, 486, all 41. profiles suitable for profile 52/34 suitable for profile 36/36, 38/17 PA - 22 - KS - 3000 00003 PA - 18H - KS - 3000 00004 46 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Cantilevers Cantilevers KON Fleible comprehensive support sstem Whether for low or ver high requirements: ou are guaranteed to find the most cost-efficient solution for our requirements using the HAFEN product range. With its adjustable bolt connections, components can be installed, dismantled, moved and adjusted quickl and simpl. Short assembl times The fleibilit of HAFEN Cantilevers/ Bolts make them ideal when the positions and sies of bolts were not finalied at the planning stage of a project. Using the HAFEN product range avoids costl and comple adjustment work, drilling or thread cutting, in corrosion protected components. Heav dut framing sstem: Medium dut framing sstem: ight dut framing sstem: KON 52/2 Pipe supports with cantilevers brackets in a sewage treatment plant KON 41/1 KON 41/D KON 28/1 KON 36/1 Heav Dut Medium Dut ight Dut Note: Depending on the number of items ordered, custom cantilevers are available KON 41/2 KON 36/2 Materials/ Statics You can find detailed information on cantilevers in our catalogue; Adjustable Framing constructions: "HAFEN Fleible Framing Connections product information, MT-FFC". 2011 HAFEN MT-FBC 10.1-E www.halfen.com 47
HAFEN FRAMING SYSTEMS Materials, Tpes HAFEN s Heav Dut Medium Dut ight Dut Heav Dut Medium Dut ight Dut Tpe: cold-rolled Order code Pages 12 26 Pages 27 35 Pages 36 43 bright-rolled WB hot dip galvanied DIN EN ISO 1461 suitable for indoor application SV hot-rolled hot-rolled: Material S235JR (RSt 37-2), DIN EN 10025, Material no. 1.0038 cold-rolled: Material S235JR (RSt 37-2), DIN EN 10025 bright-rolled Tpe HZM: S275JR (St44-2) DIN EN 10025 hot-rolled: Material S235JR (RSt 37-2), DIN EN 10025, Material no. 1.0038 cold-rolled: Material S235JR (RSt 37-2), DIN EN 10025 hot dip galvanied, DIN EN ISO 1461 inc coating min. 50 μm Tpe HZM: S275JR (St44-2) DIN EN 10025 Material S235JR (RSt 37-2), DIN EN 10025, Material no. 1.0038 or equivalent steel grade according to British Standard BS 1449, Sect. 1.4, 1991 bright-rolled Material S235JR (RSt 37-2), DIN EN 10025, W.Nr. 1.0038 or equivalent steel grade according to British Standard BS 1449, Sect. 1.4, 1991 hot dip galvanied, DIN EN ISO 1461 inc coating min. 50 μm DX51D + Z275NA DIN EN 10346 sendimir galvanied, hot dip galvanied min. 20 μm Material S235JR (RSt 37-2), DIN EN 10025, Material no. 1.0038 bright-rolled Material S235JR (RSt 37-2), DIN EN 10025, Material no. 1.0038 hot dip galvanied, DIN EN ISO 1461 inc coating min. 50 μm DX51D + Z275NA DIN EN 10346 sendimir galvanied, hot dip galvanied min. 20 μm Materials/ Statics Strip galvanied DIN EN 10142 suitable for indoor application A2 Material no. 1.4301 DIN EN 10088 stainless steel DIN EN 10088 and DIBt approval certificate Z-30.3-6 HCR Material no. 1.4571 / 1.4401, DIN EN 10088 HCR = high corrosion resistant stainless steel, Material no. 1.4529 or 1.4547, DIN EN 10088, for channels 49/30 Material no. 1.4571 / 1.4401, DIN EN 10088 Material no. 1.4571 / 1.4401, DIN EN 10088 HCR = high corrosion resistant stainless steel, Material no. 1.4529 or 1.4547, DIN EN 10088, for channels 28/15 and 38/17 48 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Materials, Tpes HAFEN Bolts / Accessories: HAFEN Bolts ocking plates Heagon head bolts Heagon nuts S-shape HAFEN Bolts for safer assembl. The head shape guarantees better hold, preventing the bolt turning in the channel, even coping with manufacturing tolerances in the channel widths. HAFEN supplies both tpes subject to change. Tpe: Order code hot-dip galvanied DIN EN ISO 10684, for threads DIN 267 section 10 galvanied inc-plated DIN 50961, DIN EN 1403, DIN EN ISO 4042 inc flake coated 8.8 8.8 l A2 Tpes HS, HSR, HZS incl. nut Pages 54-55 hot-dip galvanied in accordance with DIN EN ISO 10684 strength class 4.6 in accordance with DIN EN ISO 898-1 hot-dip galvanied in accordance with DIN EN ISO 10684 strength class 8.8 in accordance with DIN EN ISO 898-1 galvanied inc-plated with special coating Cr(VI)-free, inc coating min. 12 μm, strength class 4.6 in accordance with DIN EN ISO 898-1 galvanied inc-plated with special coating Cr(VI)-free, inc coating min. 12 μm, strength class 8.8 in accordance with DIN EN ISO 898-1 inc flake coated (onl Tpe HZS 41/41) Alternative head shape Standardhead shape Tpe GWP galvanied inc-plated Cr(VI)-free, inc coating min. 5 μm Tpe HSK DIN EN ISO 4017 Tpe MU DIN EN ISO 4032 Page 44 Page 44 galvanied inc-plated Cr(VI)-free, inc coating appro. 5 μm, strength class 8.8 hot dip galvanied in accordance with DIN EN ISO 10684 strength class 8 galvanied inc-plated Cr(VI)-free, inc coating min. 5 μm, strength class 8 Stainless steel A2 Heav Dut Medium Dut ight Dut A2-50 A2-70 Grade A2-50 according to DIN EN ISO 3506-1 DIN 267, section 11 Grade A2-70 according to DIN EN ISO 3506-1 DIN 267, section 11 Materials/ Statics Stainless steel DIN EN 10088 i.e. DIBt-approval certificate Z-30.3-6 -50-70 HCR Grade -50 according to DIN EN ISO 3506-1 DIN 267, section 11 Grade -70 according to DIN EN ISO 3506-1 DIN 267, section 11 Material no. 1.4529, Grade HCR-50 according to DIN EN ISO 3506-1 on request Stainless steel Stainless steel - 70 Stainless steel 2011 HAFEN MT-FBC 10.1-E www.halfen.com 49
HAFEN FRAMING SYSTEMS HAFEN Framing s, Non-Slotted Data Overview Heav Dut Medium Dut ight Dut Medium dut Framing sstem Heav dut Framing sstem e 2 e 1 HM 72/48 hot-rolled Tpes weight G kg/m] crosssection A [cm²] Center of gravit Moment of inertia Moment of resistance Ma. point-load bearing capacit e 1 [cm] e 2 [cm] I [cm4] I [cm4] W [cm³] W [cm³] W pl, [cm³] F WB 8.84 11.27 2.41 2.44 34.97 83.27 14.57 23.13 18.28 31.0 32 HM 52/34 WB 4.98 6.34 1.68 1.72 9.33 23.70 5.35 9.03 7.18 17.0 21 HM 50/30 WB 3.23 4.12 1.56 1.44 5.19 13.99 3.24 5.67 4.38 11.0 19 HM 40/22 WB 2.10 2.68 1.23 1.07 1.97 5.87 1.62 2.97 2.15 5.7 21 HM 72/48 D 17.63 22.46 4.85 4.85 204.04 166.14 42.51 46.15 54.88 31.0 109 HM 52/34 D 9.93 12.65 3.40 3.40 56.19 48.26 16.53 18.56 21.73 17.0 76 HM 50/30 D 6.45 8.22 3.00 3.00 27.52 28.31 9.17 11.32 11.85 11.0 61 HM 40/22 D 4.23 5.39 2.30 2.30 10.25 11.69 4.66 5.85 5.79 5.7 62 HZM 53/34 WB 4.63 5.91 1.85 1.55 9.26 23.23 5.01 8.85 6.85 22.0 25 HZM 38/23 WB 2.42 3.09 1.33 0.97 2.11 6.17 1.59 3.25 2.31 12.0 20 HZM 29/20 WB 1.51 1.98 1.12 0.88 1.02 2.42 0.91 1.67 1.31 8.0 15 HM 49/30 cold-rolled WB 2.88 3.67 1.77 1.23 4.18 13.21 2.36 5.29 3.56 4.9 46 HM 40/25 WB 2.09 2.66 1.47 1.02 2.06 6.09 1.39 3.05 2.11 3.8 33 HM 50/40 WB 3.35 4.27 2.18 1.72 8.66 15.5 3.97 6.33 5.55 5.4 63 HM 486 WB 2.31 2.95 1.55 1.15 2.97 9.62 1.92 4.01 2.71 3.5 47 HM 422(C40) WB 1.55 1.98 1.22 0.93 1.27 4.29 1.04 2.17 1.46 2.5 36 HM 41/41 WB SV 2.62 3.33 2.34 1.79 7.16 9.22 3.06 4.46 4.41 5.6 49 HZM 41/41 WB 2.62 3.25 2.38 1.75 6.91 9.10 2.91 4.41 4.26 5.6 47 HM 41/22 WB SV 1.80 2.30 1.24 0.83 1.19 5.32 0.97 2.58 1.5 5.6 15 HZM 41/22 WB 1.79 2.22 1.26 0.81 1.16 5.21 0.92 2.52 1.43 5.6 14 HM 41/83 WB SV 4.28 5.39 4.46 3.80 42.5 17.00 9.52 8.23 13.41 5.6 148 HM 41/62 WB SV 3.49 4.36 3.41 2.79 20.18 13.10 5.92 6.35 8.38 5.6 92 HM 41/41 D WB 5.23 6.67 4.13 4.13 35.81 18.44 8.67 8.93 11.97 5.6 132 HZM 41/41 D WB 5.11 6.51 4.13 4.13 33.74 18.38 8.16 8.90 11.36 5.6 126 HM 41/22 D WB 3.60 4.59 2.07 2.07 5.55 10.64 2.69 5.15 3.81 5.6 42 HZM 41/22 D 3.58 4.66 2.05 2.05 5.64 11.00 2.68 5.33 3.78 5.6 42 HM 41/62 D WB 6.85 8.72 6.20 6.20 108.11 26.21 17.45 12.69 24.31 5.6 269 F [cm] Materials/ Statics ight dut Framing sstem HM 36/36 WB 2.19 2.79 2.07 1.53 4.51 5.85 2.18 3.25 3.17 4.4 44 HM 38/17 WB A2 1.81 2.30 1.01 0.69 0.85 4.29 0.82 2.26 1.24 4.8 11 HM 315(C30) WB 0.77 0.97 0.92 0.58 0.30 1.26 0.32 0.84 0.47 1.6 17 HM 28/28 WB SV 1.36 1.73 1.58 1.22 1.70 2.01 1.08 1.49 1.54 3.0 31 HM 26/26 SV 0.82 1.05 1.48 1.12 0.94 1.18 0.64 0.91 0.89 1.1 50 HM 28/15 WB A2 1.09 1.39 0.88 0.62 0.41 1.45 0.46 1.03 0.68 3.9 8 HM 20/12 WB A2 0.52 0.66 0.72 0.48 0.12 0.36 0.16 0.36 0.25 2.2 5 Observe minimum distance a e between channel end and load point (HAFEN Bolt, locking plate): heav and medium dut framing sstems: a e 30 mm, light dut framing sstems: a e 20 mm. Do not eceed the bolt load capacit or the ma. channel load bearing capacit. For maimum point load capacit: F = ma. bending load capacit on the channel lips. Take constructive measures to prevent failure caused b possible bulging, tilting and buckling. On request. 50 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Framing s, Non-Slotted Data Overview Material: Steel, tpes WB,, SV E = 210000 N/mm² Heav dut Framing sstems Medium dut Framing sstems ight dut Framing sstems e 2 e 1 Bending load capacit at span (single span element) F fle corresponding HAFEN Bolts corresponding ocking plates F fle F fle q fle [kn/m] Tpe Thread Tpe Thread = 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m HM 72/48 22.3 11.2 7.4 16.7 8.4 5.6 89.3 22.3 9.9 HS/HSR 72/48 M20-M30 GWP 72/48 M12-M20 HM 52/34 8.8 4.4 2.8 6.6 3.3 1.6 35.1 8.8 3.0 HS/HSR 50/30 M10-M20 GWP 50/30 M8-M16 HM 50/30 5.3 2.7 1.6 4.0 2.0 0.9 21.4 5.3 1.7 HS/HSR 50/30 M10-M20 GWP 50/30 M8-M16 HM 40/22 2.6 1.3 0.6 2.0 0.8 0.3 10.5 2.1 0.6 HS/HSR 40/22 M10-M16 GWP 40/22 M6-M12 = 1.00 m 2.00 m 3.00 m 1.00 m 2.00 m 3.00 m 1.00 m 2.00 m 3.00 m HM 72/48 D 33.5 16.7 11.2 25.1 12.6 8.4 67.0 16.7 7.4 HS/HSR 72/48 M20-M30 GWP 72/48 M12-M20 HM 52/34 D 13.3 6.6 4.2 9.9 5.0 2.5 26.5 6.6 2.2 HS/HSR 50/30 M10-M20 GWP 50/30 M8-M16 HM 50/30 D 7.2 3.6 2.1 5.4 2.7 1.2 14.5 3.6 1.1 HS/HSR 50/30 M10-M20 GWP 50/30 M8-M16 HM 40/22 D 3.5 1.7 0.8 2.7 1.0 0.4 7.1 1.4 0.4 HS/HSR 40/22 M10-M16 GWP 40/22 M6-M12 = 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m HZM 53/34 12.5 6.2 2.8 9.3 3.7 1.6 49.8 10.0 3.0 HZS 53/34 M16-M20 - - HZM 38/23 4.2 1.4 0.6 3.2 0.8 0.4 16.8 2.3 0.7 HZS/HS 38/23 M12-M16 GWP 38/17 M12-M20 HZM 29/20 2.4 0.7 0.3 1.6 0.4 0.2 8.8 1.1 0.3 HZS/HS 29/20 M12 GWP 28/15 M8-M16 HM 49/30 4.3 2.2 1.2 3.3 1.6 0.7 17.4 4.3 1.3 HS 50/30 M10-M20 GWP 50/30 M8-M16 HM 40/25 2.6 1.3 0.6 1.9 0.8 0.4 10.3 2.2 0.7 HS 40/22 M10-M16 GWP 40/22 M6-M12 HM 50/40 6.8 3.4 2.3 5.1 2.5 1.5 27.1 6.8 2.8 HS 50/30 M10-M20 GWP 50/3(4)0 M6-M16 HM 486 3.3 1.7 0.9 2.5 1.2 0.5 13.2 3.2 0.9 HS 50/30 M10-M20 GWP 50/3(4)0 M6-M16 HM 422(C40) 1.8 0.9 0.4 1.3 0.5 0.22 7.1 1.4 0.4 HS 40/22 M10-M16 GWP 40/22 M6-M12 = 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m HM 41/41 5.4 2.7 1.8 4.0 2.0 1.3 21.5 5.4 2.3 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HZM 41/41 5.2 2.6 1.7 3.9 2.0 1.2 20.8 5.2 2.2 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HM 41/22 1.8 0.8 0.4 1.4 0.5 0.21 7.3 1.3 0.4 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HZM 41/22 1.7 0.8 0.3 1.3 0.5 0.20 7.0 1.2 0.4 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 = 1.00 m 2.00 m 3.00 m 1.00 m 2.00 m 3.00 m 1.00 m 2.00 m 3.00 m HM 41/83 8.2 4.1 2.7 6.1 3.1 1.9 16.4 4.1 1.7 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HM 41/62 5.1 2.6 1.5 3.8 1.9 0.9 10.2 2.6 0.8 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 = 1.00 m 1.50 m 2.00 m 1.00 m 1.50 m 2.00 m 1.00 m 1.50 m 2.00 m HM 41/41 D 7.3 4.9 3.7 5.5 3.7 2.7 14.6 6.5 3.7 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HZM 41/41 D 6.9 4.6 3.5 5.2 3.5 2.6 13.9 6.2 3.5 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HM 41/22 D 2.3 1.6 0.9 1.7 1.0 0.5 4.7 1.8 0.7 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HZM 41/22 D 2.3 1.5 0.9 1.7 1.0 0.6 4.6 1.8 0.8 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HM 41/62 D 14.8 9.9 7.4 11.1 7.4 5.6 29.7 13.2 7.4 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 = 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m HM 36/36 3.9 1.9 1.3 2.9 1.5 0.8 15.5 3.9 1.4 HS 38/17 M10-M16 GWP 38/17 M6-M12 HM 38/17 1.5 0.6 0.3 1.1 0.3 0.15 6.1 0.9 0.3 HS 38/17 M10-M16 GWP 38/17 M6-M10 HM 315(C30) 0.6 0.20 0.09 0.4 0.12 0.05 2.3 0.3 0.10 GWP 28/15 M6-M10 HM 28/28 1.9 0.9 0.5 1.4 0.7 0.3 7.5 1.8 0.5 HS 28/15 M6-M12 GWP 28/15 M6-M10 HM 26/26 1.1 0.5 0.3 0.8 0.4 0.16 4.3 1.0 0.3 HS 28/15 M6-M12 GWP 28/15 M6-M10 HM 28/15 0.8 0.3 0.12 0.6 0.16 0.07 3.3 0.4 0.13 HS 28/15 M6-M12 GWP 28/15 M6-M10 HM 20/12 0.3 0.08 0.04 0.19 0.05 0.02 1.0 0.13 0.04 HS 20/12 M6-M8 GWP 20/12 M5-M6 Note: For framing channels in stainless steel (E 170 000 N/mm 2 ) the bending deflection value must be individuall verified. Ffle Ffle q fle All load bearing are calculated as elastic-plastic values according to DIN 18800; these are approimate values and can be used for EC3. Partial safet coefficient F = 1.4 deflection l/150. Calculate the design value as F R,d = 1.4 F Heav Dut Medium Dut ight Dut Materials/ Statics 2011 HAFEN MT-FBC 10.1-E www.halfen.com 51
HAFEN FRAMING SYSTEMS HAFEN Framing s, Slotted Data Overview Heav Dut Medium Dut ight Dut Materials/ Statics Heav dut sstems Medium dut framing sstems ight dut sstems. H 50/40 e 2 e 1 cold-rolled Tpes weight G kg/m] crosssection A [cm²] Center of gravit Moment of inertia Moment of resistance Ma. point-load bearing capacit e 1 [cm] e 2 [cm] WB 3.15 3.73 1.95 1.95 7.14 15.36 3.65 6.27 4.68 5.4 53.5 HZ 63/63 6.35 7.09 3.01 3.29 33.07 42.95 10.06 13.63 13.51 5.6 134.0 H 41/41 WB SV 2.46 2.98 2.14 1.99 6.07 9.16 2.84 4.43 3.82 5.6 42.0 HZ 41/41 WB 2.46 2.90 2.18 1.95 5.87 9.04 2.69 4.38 3.70 5.6 41.0 H 41/22 WB SV 1.57 1.95 1.11 0.96 0.99 5.27 0.89 2.55 1.27 5.6 12.0 HZ 41/22 WB 1.57 1.87 1.13 0.94 0.97 5.15 0.86 2.49 1.23 5.6 12.0 H 41/83 WB 3.93 5.02 4.19 4.07 37.07 16.93 8.85 8.20 12.03 5.6 133.0 H 41/62 WB 3.14 3.99 3.16 3.04 17.27 13.03 5.47 6.31 7.35 5.6 81.0 H 36/36 WB 2.00 2.42 1.85 1.75 3.65 5.78 1.97 3.21 2.64 4.4 36 H 28/28 WB SV 1.22 1.48 1.39 1.41 1.33 1.98 0.95 1.47 1.25 3.0 25 H 26/26 SV 0.72 0.89 1.29 1.31 0.73 1.16 0.56 0.89 0.72 1.1 40 I [cm4] I [cm4] H 28/15 WB A2 0.86 1.16 0.79 0.71 0.32 1.35 0.40 0.98 0.55 3.9 7 H 20/12 WB A2 0.45 0.53 0.61 0.59 0.09 0.35 0.14 0.36 0.19 2.2 4 Observe minimum distance a e between channel end and load point (HAFEN Bolt, locking plate): heav- and medium-dut Framing sstems: a e 30 mm, light-dut Framing sstems: a e 20 mm. Do not eceed the bolt load capacit or the ma. channel load bearing capacit. For maimum point load capacit: F = ma. bending load capacit on the channel lips. Take constructive measures to prevent failure caused b possible bulging, tilting and buckling. On request. W [cm³] W [cm³] W pl, [cm³] F F [cm] All load bearing are calculated as elastic-plastic values according to DIN 18800; these are approimate values and can be used for EC3. Partial safet coefficient F = 1.4. Deflection l/150. Calculate the design value as F R,d = 1.4 F Note: For framing channels in stainless steel (E 170 000 N/mm 2 ) the bending deflection value must be individuall verified. 52 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS HAFEN Framing s, Slotted Data Overview Material: Steel, tpes WB,,SV E = 210000 N/mm² Heav dut sstems Medium dut sstems ight dut sstems e 2 e 1 Bending load capacit at span (single span element) corresponding HAFEN Bolts corresponding ocking plates F fle F fle q fle [kn/m] Tpe Thread Tpe Thread = 0.50m 1.00m 1.50m 0.50m 1.00m 1.50m 0.50m 1.00m 1.50m H 50/40 5.7 2.9 1.9 4.3 2.1 1.3 22.9 5.7 2.3 HS 50/30 M10-M20 HZ 63/63 16.5 8.2 5.5 12.4 6.2 4.1 66.0 16.5 7.3 HZS 41/41.41/22 M8-M16 Heav dut Framing sstems H D A a 50/40 18 40 60 20 63/63 14 28 250 222 Medium dut Framing sstems H/HZ D A a 41/41 14 28 50 22 41/22 14 28 50 22 41/83 14 28 50 22 41/62 14 28 50 22 GWP 50/30 GWP 50/40 GWP 41/41 GWP 41/22 M6-M16 M6-FM12 M6-M16 H 41/41 4.7 2.3 1.6 3.5 1.7 1.1 18.7 4.7 1.9 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HZ 41/41 4.5 2.3 1.5 3.4 1.7 1.0 18.1 4.5 1.9 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 H 41/22 1.6 0.7 0.3 1.2 0.4 0.17 6.2 1.1 0.3 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 HZ 41/22 1.5 0.6 0.3 1.1 0.4 0.16 6.0 1.0 0.3 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 = 1.00 m 2.00 m 3.00 m 1.00 m 2.00 m 3.00 m 1.00 m 2.00 m 3.00 m H 41/83 7.3 3.7 2.4 5.5 2.8 1.6 14.7 3.7 1.5 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 H 41/62 4.5 2.2 1.3 3.4 1.7 0.8 9.0 2.2 0.7 HZS 41/41. 41/22 M8-M16 GWP 41/41 M6-M16 = 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m 0.50 m 1.00 m 1.50 m H 36/36 3.2 1.6 1.1 2.4 1.2 0.6 12.9 3.2 1.2 HS 38/17 M10-M16 GWP 38/17 M6-M12 H 28/28 1.5 0.8 0.4 1.1 0.5 0.23 6.1 1.4 0.4 HS 28/15 M6-M12 GWP 28/15 M6-M10 H 26/26 0.9 0.4 0.22 0.7 0.3 0.13 3.5 0.8 0.23 HS 28/15 M6-M12 GWP 28/15 M6-M10 H 28/15 0.7 0.22 0.10 0.5 0.13 0.06 2.7 0.3 0.10 HS 28/15 M6-M12 GWP 28/15 M6-M10 H 20/12 0.23 0.06 0.03 0.14 0.04 0.02 0.8 0.10 0.03 HS 20/12 M6-M8 GWP 20/12 M5-M6 Hole sies and spacing A a D F fle Ffle Ffle q fle ight dut Framing sstems D A a H 36/36 15 40 60 20 28/28 12.5 25 40 15 26/26 12.5 25 40 15 28/15 9 25 40 15 20/12 9 25 40 15 Heav Dut Medium Dut ight Dut Materials/ Statics Other hole sies or hole spacing on request. 2011 HAFEN MT-FBC 10.1-E www.halfen.com 53
l l l l l l l HAFEN FRAMING SYSTEMS Product Range Overview: HAFEN Bolts Heav Dut Medium Dut ight Dut HAFEN Bolt for channel HM 72/48 Tpe HS 72/48 Page ength l and Diameter 15 HSR 72/48 HM 52/34, HM 50/30, HM 49/30, HM/H 50/40, HM 486 HS 50/30 HSR 50/30 HS 40/22 HM 40/22, HM 40/25, HM 422 HZM 38/23 HSR 40/22 HS 38/23 HZS 38/23 page 13 p. 13 page 17 page 17 page 19 p. 19 p. 23 page 23 M20 M24 M27 M30 M20 M10 M12 M16 M20 M16 M20 M10 M12 M16 M16 M16 M12 M16 20 25 30 35 40 45 50 55 60 63 65 58 59.5 41 HCR 41.5 32.5 32.5 i 33.9 32.5 29 29 Materials/ Statics 70 75 80 100 i HCR i i 125 150 200 250 300 Detailed information on strength classification and permissible loads of HAFEN Bolts can be found on the respective product page. 54 2011 HAFEN MT-FBC 10.1-E www.halfen.com
l l l l l l HAFEN FRAMING SYSTEMS Product Range Overview: HAFEN Bolts HZM 53/34 HZM 38/23, HM/H 36/36, HM 38/17 HZS 53/34 HS 38/17 HZM 29/20 HS 29/20 HZS 29/20 HZM 29/20, HM/H 28/28, HM/H 26/26, HM/H 28/15 HM/H/H/HZM/HZ 41/41, 41/22, HM/H 41/62, HM/H 41/83 HZ 63/63 HM/H 20/12 HS 28/15 HS 41/41 HZS 41/41 HZS 41/22 HS 20/12 page 21 page 23 p. 25 p. 25 page 25 page 34 page 34 page 34 page 43 41.6 41.6 M16 M20 M10 M12 M16 M12 M12 M6 M8 M10 M12 M10 M12 M6 M8 M10 M12 M16 M12 M16 M6 M8 A2 A2 A2 29 A2 A2 HCR i A2 HCR A2 A2 i A2 21 A2 20 A2 HCR A2 i A2 HCR l l l l l 35.2 35.2 l l l d b l 34.5 34.5 l l l 34.5 32.5 15.5 A2 A2 A2 Heav Dut Medium Dut ight Dut i i l Materials/ Statics i = eft hand thread 2011 HAFEN MT-FBC 10.1-E www.halfen.com 55
HAFEN FRAMING SYSTEMS Bearing Capacit Values for Welded and Bolted HAFEN Framing s Framing channels welded on to steel elements or anchored in concrete elements Heav Dut Medium Dut ight Dut Materials/ Statics F Bearing capacit values for welded/bolted HAFEN Framing channels Tpe Weld seam Support distance Bearing capacit Hot-rolled channel Cold-rolled channel F F Tension area α 60 Transverse tension area < 60 The bearing capacit values for transverse tensions appl to a transverse tension load on the channel s front edge. With greater load distances (e.g. installation distance) the additional bolt bending moment must be considered and overlaid with the transverse tension loads; see page 57 aw aw Thickness a w ength l w e w Tension α 60 Tran. Pull < 60 F F HM 72/48 5 50 300 31.0 9.3 HM 52/34 4 30 200 17.0 5.9 HM 50/30 3 30 200 11.0 3.0 HM 40/22 3 30 150 5.7 2.5 longitudinal-pull F HZM 53/34 4 30 200 22.0 6.2 22.0 / 19.0 HZM 38/23 3 30 200 12.0 3.3 12.0 HZM 29/20 3 30 150 8.0 2.2 8.0 HM 50/40 3 30 400 5.4 1.9 HZM 41/41 3 30 300 5.6 1.2 5.0 HZM 41/22 3 30 120 5.6 1.5 5.0 HM 41/41 3 30 300 5.6 1.2 HM 41/22 3 30 120 5.6 1.5 HM 36/36 3 30 300 4.4 1.2 HM 38/17 3 30 100 4.8 2.5 HM 28/15 3 30 100 2.5 1.2 Recommended loads for longitudinal channel direction for smooth (non-toothed) framing channels can be found on the respective product page. For stainless steel. ew F ew F ew F F Tension loads in unfavorable position, load distance e w F Tension loads in unfavorable position, load distance e w F F ew F F ew F ew F F F 56 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Permissible bending moment of the HAFEN Bolts Permissible lateral bearing moment Thread 4.6 M s [Nm] 8.8 M s [Nm] Grade A2-50, - 50 M s [Nm] A2-70, - 70 M s [Nm] M 6 2.0 5.1 1.8 3.8 M 8 5.0 12.5 4.4 9.4 M 10 10.0 24.9 8.7 18.7 M 12 17.5 43.7 15.3 32.8 M 16 44.4 111.0 38.8 83.3 M 20 86.5 216.4 75.7 162.3 M 24 149.7 374.2 131.1 M 27 221.9 554.8 M 30 299.9 749.7 Q F s M s applies to the front edge of the HAFEN M [Nm] M [Nm] 72/48 498 41/41 81 52/34 231 36/36 39 50/30 99 38/17 30 40/22 52 315 7 38/23 87 28/28 20 29/20 52 26/26 7 50/40 109 28/15 15 486 53 20/12 5 422 28 - - Note: The bending moment of the HAFEN Bolt M s must not eceed the lateral bearing moment M of the HAFEN Bolt. Application eample: stand-off installation square washer With stand-off installations alwas use a four sided washer. Eample: Framing channel: HM 49/30 HAFEN Bolt: HSR 50/30 - M16 Washer: VUS 52/34 - M16 Bending moment M s : see table above M Heav Dut Medium Dut ight Dut Overla of bolt bending moment with transverse load Q: Q F s (1 (Q )/M s ) Materials/ Statics For F s refer to the respective product page. 2011 HAFEN MT-FBC 10.1-E www.halfen.com 57
HAFEN FRAMING SYSTEMS Framing s as Compression Elements HAFEN Framing channels as compression elements Heav Dut Medium Dut ight Dut Buckling calculated according to DIN 18800, these are approimate values and can be used for EC3. (Point-load applied at P) oad bearing capacit F K P S Tpe channel data permissible load F K for element length e A e l W W pl i min 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 [cm²] [cm] [cm 4 ] [cm³] [cm³] [cm] F K F K F K F K F K F K F K F K F K F K HM 72/48 11.23 2.41 34.99 14.33 18.28 1.77 60.3 54.5 46.1 36.9 29.2 23.2 18.7 15.3 12.7 10.7 HM 52/34 6.32 1.68 9.42 5.49 7.09 1.22 32.1 26.1 19.0 13.6 10.0 7.5 5.9 4.7 3.8 3.1 HM 52/34 D 12.65 3.40 56.19 16.53 21.73 2.11 54.7 53.2 47.4 41.3 35.6 30.4 25.9 21.9 18.4 15.6 HM 50/30 4.11 1.56 5.23 3.35 4.34 1.13 21.9 16.9 11.7 8.1 5.8 4.4 3.3 2.6 HM 40/22 2.70 1.23 2.02 1.65 2.19 0.87 13.6 8.9 5.5 3.6 2.5 1.8 HM 50/40 4.27 2.18 8.66 3.97 5.55 1.42 22.9 19.6 15.2 11.3 8.5 6.5 5.1 4.1 3.4 2.8 H 50/40 3.73 1.95 7.14 3.65 4.68 1.38 19.1 16.3 12.5 9.3 7.0 5.4 4.2 3.4 2.8 2.3 HZ 63/63 7.09 3.01 33.07 10.06 13.51 2.16 26.8 26.4 23.3 21.3 19.2 17.1 15.2 13.4 11.9 10.5 HM/HZM 41/41 3.25 2.38 6.91 2.91 4.26 1.46 16.9 14.6 11.5 8.7 6.6 5.1 4.0 3.2 HM/HZM 41/41D 6.51 4.13 33.74 8.16 11.36 1.68 27.5 25.5 23.2 20.7 17.4 13.8 11.1 9.1 7.5 6.3 HZ/H 41/41 2.90 2.18 5.87 2.69 3.70 1.42 14.4 12.5 9.8 7.4 5.6 4.3 3.4 2.7 HM 36/36 2.79 2.07 4.51 2.18 3.17 1.27 14.3 11.8 8.7 6.3 4.6 3.5 2.7 H 36/36 2.42 1.85 3.65 1.97 2.64 1.23 11.7 9.6 7.1 5.1 3.8 2.8 2.2 HM 28/28 1.73 1.58 1.70 1.08 1.54 0.99 8.5 6.2 4.1 2.8 2.0 H 28/28 1.48 1.39 1.33 0.95 1.25 0.95 6.7 4.9 3.2 2.2 1.5 HM 26/26 1.05 1.48 0.94 0.64 0.89 0.95 5.2 3.7 2.3 1.6 Materials/ Statics H 26/26 0.89 1.29 0.73 0.56 0.72 0.91 4.1 2.9 1.8 1.2 F K = permitted working load Partial safet factor for the effect of F = 1.4, E = 170 000 N/mm² F K = permissible load Partial safet factor for the effect of F = 1.4, E = 210 000 N/mm² Note: The ma. capacit for loads that are particularl eccentric should be calculated for buckling in accordance with Eurocode 3. 58 2011 HAFEN MT-FBC 10.1-E www.halfen.com
HAFEN FRAMING SYSTEMS Calculating the bolt ength for HAFEN Bolts Calculating the bolt lengths l erf for HAFEN Bolts (steel construction) i t fi lerf s v min Halfenschraube Deduction length for HAFEN Bolts (heav dut framing sstem) l erf = t fi + i + s + v min l erf = required bolt length t fi = thickness; attached component i = channel lip thickness s = washer thickness see page 44 v min = m + u m = nut height DIN EN ISO 4032 u = Bolt protrusion appro ca. 5 mm according to DIN 78 (bolts larger M20 require min. 7 mm ) Thread HM 72/48 HM 52/34 HM 50/30 HM 49/30 HM 40/22 HM 40/25 HM 422 HZM 38/23 Dimensions V min Bolt diameter v min = m + u M6 11.0 M8 12.5 M10 14.5 M12 17.0 M16 20.5 M20 26.0 M24 29.0 M27 31.5 M30 33.5 Thickness channel lip i profile 28/15 29/20 38/17 38/23 40/22 40/25 41/22 49/30 50/30 52/34 53/34 54/33 55/42 72/48 72/49 i 2.25 5.0 3.0 5.5 6.0 5.6 5.4 7.2 7.39 7.85 10.5 7.5 7.9 12.9 15.5 9.9 Required bolt length Sch The required bolt length Sch is the sum of the clamp thickness KD and the deduction length Ab. The thread protrusion v has to etend pass the nut at least 0.5 the nut height m (DIN EN 24032 regulation for nuts). Sch = KD + Ab Ab = h + m + v Deduction length Ab according to the table below HZM 29/20 HM 50/40 HM 486 HZ 63/63 M6 M8 12 M10 24 20 20 18 18 18 17 15 M12 27 24 23 22 22 22 21 16 19 18 19 M16 33 30 29 28 28 28 27 20 23 22 23 M20 42 38 34 34 29 28 29 M24 47 33 32 33 M27 50 M30 53 v m h ma KD Sch Heav Dut Medium Dut ight Dut Materials/ Statics Deduction length for HAFEN Bolts (medium dut framing sstem) Thread HM 41/41 HM 41/22 HM 41/62 HM 41/83 H 41/41 H 41/22 M6 M8 18 18 18 18 18 18 M10 19 19 19 19 19 19 M12 23 23 23 23 23 23 M16 29 29 29 29 29 29 Deduction length for HAFEN Bolts (light dut framing sstem) Thread HM 36/36 HM 38/17 HM 28/28 HM 26/26 HM 28/15 HM 315 HM 20/12 M6 M8 10 9 10 9 9 M10 15 15 13 12 13 12 12 M12 18 19 14 13 14 14 M16 24 25 18 17 18 17 2011 HAFEN MT-FBC 10.1-E www.halfen.com 59
HAFEN FRAMING SYSTEMS Applications in Mechanical Engineering and Industrial Plant Construction Static and dnamic tension tests Heav Dut Medium Dut ight Dut The transferabilit of static and dnamic loads for adjustable assembl sstems was rigorousl studied in cooperation with the State Material Testing Institute at the TU Darmstadt (Technical Universit Darmstadt). 60 40 20 HS 40/22-HM 40/22 HS40/22-HM40/22_01 HS40/22-HM40/22_02 HS40/22-HM40/22_03 0 0 100 200 300 400 Graph: Tightening tests Following VDI guideline 2230, the data acquired from bolt tightening tests, static and dnamic traction tests form the basis of algorithms used for calculating adjustable assembl sstems. 35 30 25 20 15 10 5 0 0 a120f1 a120f2 a120f3 1 2 3 4 5 6 Materials/ Statics Graph: tension test Tightening test Tension test Fatigue test 60 2011 HAFEN MT-FBC 10.1-E www.halfen.com