EUD240SxxxDVL Features Innovative Design with No Electrolytic Capacitors Ultra Long Lifetime: Greater than 100,000 hrs at 85 C Case Temperature Full Power at Wide Output Current Range (Constant Power) Thermal Sensing and Protection for LED Module 010V/PWM/Timer Dimmable (3 Timer Modes ) DimtoOff with Standby Power 0.5 W Alwayson Auxiliary Power: 12Vdc, 200mA Output Lumen Compensation Input Surge Protection: 6kV lineline, 10kV lineearth AllAround Protection: OVP, SCP, OTP Waterproof (IP67) SELV Output Suitable for Independent Use 10 Years Warranty Description The EUD240SxxxDVL series is a novel 240W design that has removed the use of Electrolytic capacitors to extend lifetime at elevated temperatures. It is a constantcurrent, programmable LED driver that operates from 90305 Vac input with excellent power factor. Created for high bay, high mast, arena and roadway lights, it provides a dimtooff mode with low standby power. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure troublefree operation, protection is provided against input surge, output over voltage, short circuit, and over temperature of both the driver and the external LED array. Models Adjustable Output Current Range FullPower Current Range (1) Default Output Current Input Voltage Range(2) Output Voltage Range Max. Typical Power Factor Output Efficiency Power (3) 120Vac 220Vac Model Number (5) 701050mA 7001050mA 1050 ma 90~305Vac 114~343Vdc 240W 127~250Vdc 93.5% 0.98 0.96 EUD240S105DVL 1402100mA 14002100mA 1400 ma 90~305Vac 57~171Vdc 127~250Vdc 240W 93.5% 0.98 0.96 EUD240S210DVL 2804200mA 28004200mA 4200 ma 90~305Vac 29 ~ 86Vdc 127~250Vdc 240W 92.5% 0.98 0.96 EUD240S420DVL(4) 4456700mA 44506700mA 6700 ma 90~305Vac 18 ~ 54Vdc 127~250Vdc 240W 92.5% 0.98 0.96 EUD240S670DVL(4) Notes: (1) Output current range with constant power at 240W (2) Certified input voltage range: 100240Vac or 127250Vdc (except CCC, PSE and KS) (3) Measured at full load and 220Vac input (see below General Specifications for details). (4) SELV Output. (5) All the models are certificated to KS,except EUD240S105DVL 1 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL EUD240S105DVL IV Operating Area EUD240S210DVL Output Voltage(V) 60%Load EUD240S420DVL EUD240S670DVL Input Specifications Input Voltage 90 Vac 305 Vac 127~250 Vdc Input Frequency 47 Hz 63 Hz Leakage Current 0.70 ma IEC605981; 240Vac/ 60Hz Input AC Current 2.85 A Measured at full load and 100 Vac input. 1.22 A Measured at full load and 220 Vac input. Inrush Current(I 2 t) 1.72 A 2 s At 220Vac input, 25 C Cold Start, Duration=128 μs, 10%Ipk10%Ipk. See Inrush Current Waveform for the details. 2 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL Input Specifications (Continued) PF 0.90 THD 20% THD 10% At 100240Vac, 5060Hz, 60%100% Load (144240W) At 220240Vac, 5060Hz, 75%100% Load (180240W) Output Specifications Output Current Tolerance 5%Ioset 5%Ioset At full load condition Output Current Setting(Ioset) Range EUD240S105DVL EUD240S210DVL EUD240S420DVL EUD240S670DVL Output Current Setting Range with Constant Power EUD240S105DVL EUD240S210DVL EUD240S420DVL EUD240S670DVL Total Output Current Ripple (pkpk) Output Current Ripple at < 200 Hz (pkpk) 70 ma 140 ma 280 ma 445 ma 700 ma 1400 ma 2800 ma 4450 ma 1050 ma 2100 ma 4200 ma 6700 ma 1050 ma 2100 ma 4200 ma 6700 ma 8%Iomax 15%Iomax At full load condition, 20 MHz BW 2%Iomax Startup Overshoot Current 10%Iomax At full load condition At full load condition. Only this component of ripple is associated with visible flicker. No Load Output Voltage EUD240S105DVL EUD240S210DVL EUD240S420DVL EUD240S670DVL 360 V 190 V 96 V 61 V Line Regulation ±0.5% Measured at full load Load Regulation ±1.5% Turnon Delay Time Temperature Coefficient of Ioset 1.0 s 0.5 s 12V Auxiliary Output Voltage 10.8 V 12 V 13.2 V Measured at 120Vac input, 60%100% Load Measured at 220Vac input, 60%100% Load 0.03%/ C Case temperature = 0 C ~Tc max 12V Auxiliary Output Source 0 ma 200 ma Return terminal is Dim Current Note: All specifications are typical at 25 C unless otherwise stated. 3 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL General Specifications Efficiency at 120 Vac input: EUD240S105DVL Io= 700 ma Io= 1050 ma EUD240S210DVL Io= 1400 ma Io= 2100 ma EUD240S420DVL Io= 2800 ma Io= 4200 ma EUD240S670DVL Io= 4450 ma Io= 6700 ma Efficiency at 220 Vac input: EUD240S105DVL Io= 700 ma Io= 1050 ma EUD240S210DVL Io= 1400 ma Io= 2100 ma EUD240S420DVL Io= 2800 ma Io= 4200 ma EUD240S670DVL Io= 4450 ma Io= 6700 ma Efficiency at 277 Vac input: EUD240S105DVL Io= 700 ma Io= 1050 ma EUD240S210DVL Io= 1400 ma Io= 2100 ma EUD240S420DVL Io= 2800 ma Io= 4200 ma EUD240S670DVL Io= 4450 ma Io= 6700 ma 89.0% 88.0% 89.0% 88.0% 88.0% 86.0% 88.5% 86.5% 91.5% 91.5% 90.0% 88.5% 88.5% 92.0% 91.0% 92.0% 88.5% 91.0% 89.0% 91.0% 90.0% 91.0% 90.0% 90.0% 88.0% 88.5% 93.5% 92.5% 93.5% 92.0% 92.5% 92.5% 94.0% 93.0% 94.0% 92.5% 92.5% 93.0% 91.0% Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Standby power 0.5 W Measured at 230Vac/50Hz; Dimming off MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w 256,000 Hours 100,000 Hours 40 C +90 C 40 C +75 C Measured at 220Vac input, 80%Load and 25 C ambient temperature (MILHDBK 217F) Measured at 220Vac input, 80%Load and 85 C case temperature; See lifetime vs. Tc curve for the details Case temperature for 10 years warranty. Please see Inventronics EUDDVL Warranty Statement for complete details. Storage Temperature 40 C +85 C Humidity: 5%RH to 100%RH 4 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL General Specifications (Continued) Dimensions Inches (L W H) Millimeters (L W H) 8.86 2.66 1.56 225 67.5 39.7 Net Weight 1300 g Note: All specifications are typical at 25 C unless otherwise stated. With mounting ear 9.68 2.66 1.56 246 67.5 39.7 Dimming Specifications Absolute Maximum Voltage on the Vdim (+) Pin Source Current on Vdim (+) Pin Dimming Output Range EUD240S105DVL EUD240S210DVL EUD240S420DVL EUD240S670DVL EUD240S105DVL EUD240S210DVL EUD240S420DVL EUD240S670DVL Recommended Dimming Input Range 20 V 20 V 200 ua 300 ua 450 ua Vdim(+) = 0 V 10%Ioset Ioset 70 ma 140 ma 280 ma 445 ma Ioset 0 V 10 V Dim off Voltage 0.35 V 0.5 V 0.65 V Dim on Voltage 0.55 V 0.7 V 0.85 V Hysteresis 0.2 V PWM_in High Level 3 V 10 V PWM_in Low Level 0.3 V 0.6 V PWM_in Frequency Range 200 Hz 3 KHz PWM_in Duty Cycle 1% 99% 700 ma Ioset 1050 ma 1400 ma Ioset 2100 ma 2800 ma Ioset 4200 ma 4450 ma Ioset 6700 ma 70 ma Ioset < 700 ma 140 ma Ioset < 1400 ma 280 ma Ioset < 2800 ma 445 ma Ioset < 4450 ma Default 010V dimming mode. PWM Dimming off (Positive Logic) PWM Dimming on (Positive Logic) PWM Dimming off ( Negative Logic) PWM Dimming on ( Negative Logic) 2% 5% 8% 4% 7% 10% 92% 95% 98% 90% 93% 96% Dimming mode set to PWM in PC interface. Hysteresis 2% Note: All specifications are typical at 25 C unless otherwise stated. 5 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL Safety & EMC Compliance Safety Category Standard CE EN 613471, EN61347213 KS KS C 7655 EMI Standards EN 55015 (1) EN 6100032 EN 6100033 EMS Standards EN 6100042 EN 6100043 EN 6100044 Notes Conducted emission Test & Radiated emission Test Harmonic current emissions Voltage fluctuations & flicker Notes Electrostatic Discharge(ESD): 8kV air discharge, 4kV contact discharge RadioFrequency Electromagnetic Field Susceptibility TestRS Electrical Fast Transient/BurstEFT EN 6100045 Surge Immunity Test: AC Power Line: line to line 6kV, line to earth 10kV (2) EN 6100046 EN 6100048 EN 61000411 Conducted Radio Frequency Disturbances testcs Power Frequency Magnetic Field Test Voltage Dips EN 61547 Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2)To perform electric strength (hipot) testing, the GDT ground disconnect (nut and metal lock sheet) on the driver endcap should be removed temporarily to prevent the internal gas discharge tube from conducting (as allowed by IEC 605981 Clause 10.2). After testing is completed, these items must be reinstalled to restore linetoearth surge protection and secure the end cap. Lifetime vs. Case Temperature 6 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL Inrush Current Waveform Efficiency vs. Load EUD240S105DVL(Io=700mA) EUD240S105DVL(Io=1050mA) EUD240S210DVL(Io=1400mA) EUD240S210DVL(Io=2100mA) 7 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL EUD240S420DVL(Io=2800mA) EUD240S420DVL(Io=4200mA) EUD240S670DVL(Io=4450mA) EUD240S670DVL(Io=6700mA) Power Factor 8 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL Total Harmonic Distortion Protection Functions External Thermal Protection NTC R1 7.81 kohm R2 4.16 kohm Protection Current Floor When R_NTC falls below R1, External Thermal Protection is triggered, reducing output current until R2 is reached. When R_NTC is less than R2, output current is reduced to the programmed Protection Current Floor. 10%Ioset 60%Ioset 100%Ioset 10%Ioset>Iomin (default setting is 60%) Iomin 60%Ioset 100%Ioset 10%Ioset Iomin (default setting is 60%) Over Temperature Protection Short Circuit Protection Over Voltage Protection Decreases output current, returning to normal after over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. 9 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL Dimming 010V Dimming The recommended implementation of the dimming control is provided below. V+(BRN) L N G Vac Inventronics LED Driver V(BLU) OTP+(PINK) OTP(BLU/WHT) Vaux(BLK/WHT) Dim+(PUR) 0 (1)10V Dim(GRY) Dimmer Implementation 1: DC Input Notes: 1. The dimmer can also be replaced by an active 010V voltage source signal or passive components like resistors and zener. 2. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 3. If 010V dimming is not used, Dim + should be open. PWM Dimming V+(BRN) L N G Vac Inventronics LED Driver V(BLU) OTP+(PINK) OTP(BLU/WHT) Vaux(BLK/WHT) Dim+(PUR) Dim(GRY) PWM Signal Implementation 2: Positive logic 10 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL V+(BRN) L V(BLU) N G Vac Inventronics LED Driver OTP+(PINK) OTP(BLU/WHT) Vaux(BLK/WHT) Dim+(PUR) Dim(GRY) PWM Signal Implementation 3: Negative logic Notes: 1. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 2. If PWM dimming is not used, Dim + should be open. 3. When PWM negative logic dimming mode and Dim+ is open, the driver will output minimum current. Time Dimming Time dimming control includes 3 kinds of modes, they are Self AdaptingMidnight, Self Adapting Percentage and Traditional Timer. Self AdaptingMidnight: Automatically adjusts the dimming curve based on the ontime of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self AdaptingPercentage: Automatically adjusts the ontime of each step by a constant percentage = (actual ontime for the past 2 days if difference <15 min) / (programmed ontime from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes. Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. 11 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRGMUL2 MultiProgrammer datasheet for details. Mechanical Outline INPUT(VDE H05RNF 3*1.0mm 2 7.2) DIMMING WIRE(VDE H05RNF 5*0.5mm 2 7.2) AC/L(BROWN) AC/N(BLUE) GND(YELLOW/GREEN) Tc V+(BROWN) V(BLUE) PINK BLUE/WHITE BLACK/WHITE PURPLE GRAY OUTPUT(VDE H05RNF 2*1.0mm 2 6.8) PROJ: Unspecified tolerance:±1 RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products. 12 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD240SxxxDVL Revision History Change Date Rev. Description of Change Item From To 20170809 A Datasheets Release / / 13 / 13 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com