5170 General Description Typical Application The 5170 is a fixed off-time step-up DC/DC converter in a small SOT-25/TSOT-25A package.the 5170 is ideal for LCD panels requiring low current and high efficiency as well as LED application for cellular phone backlighting, PDAs, and other hand-held devices. The low 400ns off time allows the use of tiny external components. 5170 is designed to drive up to four white LEDs in series with a constant current from a single Li-lon battery. To control LED brightness, the LED current can be adjusted by applying a PWM (pulse width modulated) signal with a frequency range of 100Hz to 50KHz to the EN pin. V IN 1.5V to 5V C IN 4.7µF L1 2.2µH IN SW EN 5170 GND FB R1 100KΩ R2 33KΩ V OUT = 5V CF 20pF C OUT 4.7µF Figure.1 Typical 5V Application Features V IN 1.5V to 5.5V L1 10µH V OUT = 12V 0.7Ω Internal Switch Use Small Surface Mount Components Adjust Output Voltage up to 28V Input under Voltage Lockout 0.1µA Shutdown Current Typical Small SOT-25/TSOT-25A Package All 's Lead Free Products Meet RoHS Standards C IN 4.7µF IN SW EN 5170 GND FB R1 240KΩ R2 27KΩ C OUT 1µF Applications LCD Bias Supplies White LED Back-Lighting Handheld Devices Digital Cameras Portable Applications C IN 4.7µF V IN 1.5V to 5.5V Figure.2 Typical 12V Application IN EN L1 10µH 5170 SW V OUT = 20V R1 510KΩ C OUT 1µF GND FB R2 33KΩ Figure.3 Typical 20V Application 1
5170 Typical Application V IN 2.7V to 5.5V L1 10µH V OUT C IN 4.7µF IN SW C OUT 1µF 5170 EN GND FB R2 62Ω Figure.4 White LED Application Function Block Diagram IN SW + Enable Comp - FB 1 : 8 V IN V REF - CL Adjust + Current Limit 400ns one Shot Cs UVP Logic Control Driver EN GND Figure.5 Function Block Diagram 2
5170 Pin Configuration SOT-25/TSOT-25A Top View 5 4 5170 1 2 3 5170AEEV 1. SW 2. GND 3. FB 4. EN 5. IN Die Attach: Conductive Epoxy Pin Description Pin Number Pin Name Pin Description 1 SW 2 GND 3 FB 4 EN 5 IN Power Switch input. This is the drain of the internal NMOS power switch. Minimize the metal trace area connected to this pin to minimize EMI. Ground. Tie directly to ground plane. Output voltage feedback input. Set the output voltage by selecting values for R1 and R2 using: V out R1 = R 2 1 1.23V Connect the ground of the feedback network to an AGND(Analog Ground) plane which should be tied directly to the GND pin. Enable control input, active high. The enable pin is an active high control. Tie this pin above 1.5V to enable the device. Tie this pin below 0.4V to turn off the device. Analog and Power input. Input Supply Pin. Bypass this pin with a capacitor as close to the device as possible. 3
5170 Ordering Information 5170 x x x x xxx x Special Feature Output Voltage Number of Pins Package Type Operating Ambient Temperature Range Pin Configuration Pin Configuration Operating Ambient Temperature Range Package Type Number of Pins Output Voltage Special Feature A 1. SW E: -40 O C to +85 O C E: SOT-2X V: 5 ADJ: Adjustable Z: Lead free (SOT-25) 2. GND Y: Lead free (TSOT-25A) 3. FB & Low profile 4. EN K: 0.9mm max height 5. IN (for TSOT-2XA Only) Ordering Information Part Number Marking* Output Voltage Package Operating Ambient Temperature Range 5170AEEVADJZ BLEww ADJ SOT-25-40 O C to +85 O C 5170AEEVADJK BLEww ADJ TSOT-25A -40 O C to +85 O C Note: ww represents the date code and pls refer to Date Code Rule on Package Dimension. * A line on top of the first letter represents lead free plating such as BLEww. Please consult sales office or authorized Rep./Distributor for the availability of package type. 4
5170 Absolute Maximum Ratings Parameter Symbol Maximum Unit Input Supply Voltage V IN 6 V EN, FB Voltages EN,V FB V IN V SW Voltage V SW V OUT + 0.3 V N-Channel Switch Sink Current I SW 600 ma ESD Classification B* Caution: Stress above the listed absolute rating may cause permanent damage to the device. * HBM B: 2000~3999V Recommented Operating Conditions Parameter Symbol Rating Unit Ambient Temperature Range T A - 40 to +85 Junction Temperature Range T J - 40 to +125 O C Storage Temperature Range T STG - 65 to +150 Thermal Information Parameter Package Die Attach Symbol Maximum Unit Thermal Resistance* (Junction to Case) Thermal Resistance (Junction to Ambient) Internal Power Dissipation Solder Iron (10Sec)** SOT-25 140 θ JC TSOT-25A 81 SOT-25 280 Conductive Epoxy θ JA TSOT-25A 230 SOT-25 400 P D TSOT-25A 455 350 o C / W mw o C * Measure θ JC on backside center of molding compund if IC has no tab. ** MIL-STD-202G 210F 5
5170 Electrical Specifications V IN = 3.6V, EN = V IN, T A = 25 o C, C IN = 4.7µF, I L = 0A, unless otherwise noted. Parameter Symbol Test Condition Min Typ Max Units Input Voltage V IN 1.5 5.5 V Output Voltage Line Regulation 0.05 %V Quiescent Current I Q V IN = 2V 65 75 µa Shutdown Current I SD EN = 0V 0.1 1 µa FB Regulation Voltage V FB 1.20 1.23 1.26 V FB Comparator Hysteresis V FB Hysteresis 5 mv Switch Current Limit I CL 300 375 450 ma FB Pin Bias Current IFB VFB = 1.23V 1.0 µa Switch R DSON R DSON 0.6 1.0 1.4 Ω Switch Off Time t OFF 400 ns Input Undervoltage Lockout UVLO 1.2 1.4 V EN Input Threshold (High) (Enable the device) EN Input Threshold (Low) (Shutdown) EN Threshold 1.5 0.4 V 6
5170 Detailed Description The 5170 features a constant off-time control scheme. Operation can be best understood by referring to Figure 5. When the voltage at the FB pin is less than 1.23V, the Enable Comp in Figure.5 enables the device and the NMOS switch is turned on, pulling the SW pin to ground. When the NMOS switch is on, load current is supplied by the output capacitor C OUT. Once the current in the inductor reaches the peak current limit, the 400ns One Shot turns off the NMOS switch. The SW voltage will then rise to the output voltage plus a diode drop and inductor current will begin to decrease as shown in Figure3. During this time the energy stored in the inductor is transferred to C OUT and the load. After the 400ns offtime the NMOS switch is turned on and energy is stored in the inductor again. This energy transfer from the inductor to the output causes a stepping effect in the output ripple. This cycle is continued until the voltage at FB pin reaches 1.23V. When FB pin reaches this voltage, the enable comparator then disables the device turning off the NMOS switch and reducing the quiescent current of the device to 65µA typical. The load current is then supplied solely by C OUT indicated by the gradually decreasing slope at the output. When the FB pin drops slightly below 1.23V, the enable comparator enables the device and begins the cycle described previously. The EN pin can be used to turn off the 5170 and reduce the I Q to 0.1µA. In shutdown mode the output voltage will be a diode drop lower than the input voltage. DIODE SELECTION To maintain high efficiency, the average current rating of the schottky diode should be larger than the peak inductor current. Schottky diodes with a low forward drop and fast switching speeds are ideal for increasing efficiency in portable applications. Choose a reverse breakdown of the schottky diode larger than the output voltage CAPACITOR SELECTION Choose low ESR capacitors for the output to minimize output voltage ripple. Multilayer ceramic capacitors are the best choice. For most applications, a 1µF ceramic capacitor is sufficient. For some applications a reduction in output voltage ripple can be achieved by increasing the output capacitor. Local bypassing for the input is needed on the 5170. Multilayer ceramic capacitors are a good choice for this as well. A 4.7µF capacitor is sufficient for most applications. For additional bypassing, a 100nF ceramic capacitor can be used to shunt high frequency ripple on the input. LAYOUT CONSIDERATIONS The input bypass capacitor C IN, as shown in Figure 3, must be placed close to the IC. This will reduce copper trace resistance which effects input voltage ripple of the IC. For additional input voltage filtering, a 100nF bypass capacitor can be placed in parallel with C IN to shunt any high frequency noise to ground. The output capacitor, C OUT, should also be placed close to the IC. Any copper trace connections for the C OUT capacitor can increase the series resistance, which directly effects output voltage ripple. The feedback network, resistors R1 and R2, should be kept close to the FB pin to minimize copper trace connections that can inject noise into the system. The ground connection for the feedback resistor network should connect directly to an analog ground plane. The analog ground plane should tie directly to the GND pin. If no analog ground plane is available, the ground connection for the feedback network should tie directly to the GND pin. Trace connections made to the inductor and schottky diode should be minimized to reduce power dissipation and increase overall efficiency. 7
5170 Characterization Curve Switch off Time vs Temperature I FB vs Temperature Switch off time (ns) 700 650 600 550 500 450 400 IFB(mA) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 I Q vs Temperature EN Thershold High vs Temperature I Q (ma) 75 60 45 30 15 0 EN Threshold(V) 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 EN Threshold(V) 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 EN Threshold Low vs Temperature 0.4 Switch Current Limit(mA) 700 600 500 400 300 Switch Current Limit vs Temperature 200 8
5170 Characterization Curve R DSON vs Temperature V FB vs Temperature R DSON ( ) 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 1.50 1.45 1.40 UVLO vs Temperature VFB(V) 1.26 1.25 1.24 1.23 1.22 1.21 1.20 95 85 Efficiency vs Load Current UVLO(V) 1.35 1.30 1.25 1.20 1.15 Efficiency(%) 75 65 55 V IN=2.5V V IN=3.3V V IN =4.2V 1.10 1.05 45 V OUT =20V 1.00 Output Voltage vs Load Current 35 1 4 8 12 16 20 24 28 Load Current(mA) Efficiency vs Load Current 20.25 V IN =2.5V 95 Output Voltag e(v) 20.20 20.15 20.10 20.05 20.00 V IN =3.3V V IN=4.2V C OUT =1µF V OUT=20V Efficiency(%) 85 75 65 55 45 V IN =2.5V V IN =3.3V V IN =4.2V V IN=5.0V V OUT=12V 19.95 1 4 8 12 16 20 24 28 Load Current(mA) 35 1 12 24 36 48 60 72 Load Current(mA) 9
5170 Characterization Curve Output Voltage vs Load Current Efficiency vs Load Current 12.35 V IN =2.5V 95 Output Voltage(V) 12.25 12.15 12.05 11.95 V IN =3.3V V IN =4.2V V IN =5.0V C OUT=1µF V OUT =12V 11.85 1 8 16 24 32 40 48 56 64 72 Load Current(mA) Efficiency(%) 85 75 65 55 45 V IN =4.2V V IN =3.3V V IN =2.5V V OUT =5V 35 1 24 48 72 96 120 144 168 Load Current(mA) Output Voltage vs Load Current 4.95 C OUT=4.7µF V OUT=5V Output Voltage(V) 4.90 4.85 4.80 V IN =2.5V V IN=4.2V V IN=3.3V 4.75 1 24 48 72 96 120 144 168 Load Current(mA) 10
5170 Date Code Rule Marking Date Code Year A A A W W xxx0 A A A W W xxx1 A A A W W xxx2 A A A W W xxx3 A A A W W xxx4 A A A W W xxx5 A A A W W xxx6 A A A W W xxx7 A A A W W xxx8 A A A W W xxx9 Tape and Reel Dimension SOT-25 P W PIN 1 Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size SOT-25 8.0±0.1 mm 4.0±0.1 mm 3000pcs 180±1 mm 11
5170 Tape and Reel Dimension TSOT-25A P W PIN 1 Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size TSOT-25A 8.0±0.1 mm 4.0±0.1 mm 3000pcs 180±1 mm 12
5170 Package Dimension SOT-25 Top View D Side View SYMBOLS A MILLIMETERS INCHES MIN MAX MIN MAX 1.20REF 0.0472REF A 1 0.00 0.15 0.0000 0.0059 H E b 0.30 0.55 0.0118 0.0217 D 2.70 3.10 0.1063 0.1220 E 1.40 1.80 0.0551 0.0709 S1 e Front View A L e 1.90 BSC 0.07480 BSC H 2.60 3.00 0.10236 0.11811 L 0.37BSC 0.0146BSC q1 0 o 10 o 0 o 10 o S 1 0.95BSC 0.0374BSC b A1 TSOT-25A D b q SYMBOLS MILLIMETERS INCHES MIN MAX MIN MAX L A 0.700 0.900 0.028 0.035 0.25 A1 0.000 0.100 0.000 0.004 E1 E A2 0.700 0.800 0.028 0.031 b 0.350 0.500 0.014 0.020 c 0.080 0.200 0.003 0.008 PIN 1 e e1 TOP VIEW A1 c SIDE VIEW D 2.820 3.020 0.111 0.119 E 1.600 1.700 0.063 0.067 E1 2.650 2.950 0.104 0.116 e 0.95 BSC 0.037 BSC e1 1.90 BSC 0.075 BSC A2 A L 0.300 0.600 0.012 0.024 REAR VIEW q 0 o 8 o 0 o 8 o 13
5170 Lead pattern SOT-25 0.70 BSC 2.40 BSC 1.00 BSC 0.95 BSC 0.95 BSC 1.90 BSC Note: 1. Lead pattern unit description: BSC: Basic. Represents theoretical exact dimension or dimension target. 2. Dimensions in Millimeters. 3. General tolerance +0.05mm unless otherwise specified. 14
5170 Lead pattern TSOT-25A 0.70 BSC 2.40 BSC 1.00 BSC 0.95 BSC 0.95 BSC 1.90 BSC Note: 1. Lead pattern unit description: BSC: Basic. Represents theoretical exact dimension or dimension target. 2. Dimensions in Millimeters. 3. General tolerance +0.05mm unless otherwise specified. 15
www.ame.com.tw E-Mail: sales@ame.com.tw Life Support Policy: These products of, Inc. are not authorized for use as critical components in life-support devices or systems, without the express written approval of the president of, Inc., Inc. reserves the right to make changes in the circuitry and specifications of its devices and advises its customers to obtain the latest version of relevant information., Inc., October 2011 Document: 1231-DS5170-A.05 Corporate Headquarter, Inc. 2F, 302 Rui-Guang Road, Nei-Hu District Taipei 114, Taiwan, R.O.C. Tel: 886 2 2627-8687 Fax: 886 2 2659-2989