AUTOMATE PARADIGM FLUSH WALL SWITCH FRONT BACK CHANNELS P2 BUTTON STOP UP DOWN PACK CONTENTS Switch Fixing screws & anchors Instruction Manual 3V CR2430 Battery TECHNICAL SPECIFICATIONS Voltage: Frequency: 3V (CR2430) 433.92 MHz TransmittingPower: 10 milliwatt Ambient Operating Temperature: Transmission Distance: -10 C - 50 C up to 200 meters (open space) 433MHz Page. 1 of 6
CONTENTS Installing switch battery Mounting switch Select channel Pairing to motor Group Control Adding & deleting switches. Adding & deleting channels. Troubleshooting p3 p3 p4 p4 p4 p5 p5 p6 U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity required for EU market CAUTION Do not expose to moisture or extreme temperatures Replace with correct battery type as specified Do not allow children to play with this device or battery. Use or modification outside the scope of this instruction manual will void warranty. DISPOSAL Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately Page. 2 of 6
INSTALL SWITCH BATTERY 1 2 Remove cover from switch: Insert a flat-tip screw driver into the gap between covers located on the bottom of switch. Twist driver as shown to separate switch halves. Install battery with positive(+) side facing up 3 Replace cover by placing halves together and pressing firmly until snaps engage MOUNTING SWITCH Use supplied fasteners and anchors as needed to attach base to desired surface as shown in figure NEED STP FILE FOR MOUNT TO CREATE ILLUSTRATION HERE Page. 3 of 6
1. SELECT CHANNEL Detail View of Switch Controls 1a To select a channel or group of channels: Press desired channel button(s) until LED s appear 1b To de-select a channel: Press channel button(s) until channel LED disappears 2. PAIRING SWITCH TO MOTOR ACTIVATE PAIRING MODE ON MOTOR 2a (Any Motor) Press & hold button on motor head (3sec) OR 2a (Non-Battery Motor) Power ON motor BEEP 1X 2b Within 4sec, Press & Hold STOP (3sec) JOG 2X + BEEP 3X 3. GROUP CONTROL Explanation: in this step you are going to pair multiple motors to a single channel on your switch. This will allow you to operate a series of motors in unison without needing to change channels. Ensure that each motor you want to group is also assigned to another channel by itself Confirm that motor limits and favorite position are already set for each individual motor Select the channel you want to control the group of motors with REPEAT steps 2A and 2B for all motors using your desired group channel Page. 4 of 6
4. ADDING & DELETING SWITCHES ADDING A = Existing Controller B = Controller to be added DELETING A = Existing Controller B = Controller to be deleted 4a existing controller 4b existing controller 4c controller to be added or deleted CHANGE TO CONTROLLER TO BE ADDED OR DELETED JOG 2X + BEEP 3X 5. ADDING & DELETING CHANNELS ADDING A = Existing Channel B = Channel to be added DELETING A = Existing Channel B = Channel to be deleted 5a existing channel 5b existing channel 5c channel to be added or deleted CHANGE TO CHANNELTO BE ADDED OR DELETED JOG 2X + BEEP 3X Page. 5 of 6
TROUBLESHOOTING PROBLEM CAUSE REMEDY Motor is not responding Cannot set limits on a single Motor (multiple motors respond) Switch battery is discharged Battery is inserted incorrectly Radio interference / Shielding Receiver distance is too far from switch Power failure Incorrectwiring Using group channels to adjust motor limits Replace battery Check battery polarity Ensure switch is positioned away from metal objects and that aerial on motor or receiver is kept straight and away from metal. Move switch to a closer position. Check power supply to motor is connected and active. Check wiring is connected correctly (refer to motor installation instructions) Always reserve an individual channel for programming functions. SYSTEM BEST PRACTICE Provide an extra 15 channel switch in your multi motor projects, that provides individual control for each motor for programming purposes. ROLLEASE ACMEDA USA 200 HarvardAvenue Stamford, CT 069026320 T +1 203 964 1573 F +1 203 964 0513 ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 F +61 3 9355 0110 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan (Lombardia)Italy T +39 02 8982 7317 F +39 02 8982 7317 Western Australia Branch Unit 1, 41 MulgulRoad, Malaga WA6090 T +61 8 9248 5571 F +61 8 9248 5572 Queensland Branch Unit 2/62 Borthwick Avenue, Murarrie QLD 4172 info@rolleaseacmeda.co m rolleaseacmeda.com Page. 6 of 6