Single Mirror Cabinet Assembly Instructions - please keep for future reference YO886 464/3944 Dimensions Width - 35.5cm Depth - 16.5cm Height - 60cm Important Please read these instructions fully before starting assembly Issue 1-1/1/17
Safety and Care Advice Important Please read these instructions fully before starting assembly Check you have all the components and tools listed on page During assembly do not stand or put weight on the product, this could cause damage. plastic bags and separate them into their groups. Assemble the item as close room) as possible. Keep children and animals away from the work area, small parts could choke if swallowed. Assemble on a soft level surface to avoid damaging the Make sure you have enough space to layout the parts before starting. Parts of the assembly will be easier with people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the using. Only use hand screwdrivers Care and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Handy Hints Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts Regularly check and ensure tightend properly. WARNING In order to help prevent overturning To help prevent product toppling over please follow the below steps:do not allow children to climb or hang on the furniture Do not place heavy items in the top drawers Do not place heavy items on top of the furniture, unless the furniture has been designed for this purpose You will need to provide wall plugs and screws applicable for your wall type 1
Components - Panels Please check you have all the panels listed below 1 Left Side Panel x 1 (57(w) x 14.5(d) cm ) Right Side Panel x 1 (57(w) x 14.5(d) cm ) 4 Back Panel x 1 (57.5(w) x 3.8(d)cm) 5 Door Panel x 1 (60(w) x 35.5(d) cm) 7 Top Panel x 1 (35.5(w) x 14.5(d) cm) 8 Base Panel x 1 (35.5(w) x 14.5(d) cm) 3 Cross Plinth x (3.3(w) x 4.5(d) cm) 6 Shelf Panel x 1 (3(w) x 13(d) cm)
Components - Fittings Note: may be supplied than are required. Male Camlocks x 8 14mm Screw x 8 Female Camlocks x 8 30mm Dowel x 8 Shelf Supports x 4 1mm Screw x 9 Push Catch x 1 Catch Plate x 1 Panel Stiffeners x 4 Hinges x Tools required Phillips screwdriver (medium & large) Ruler Use this ruler to help correctly identify the screws 0 5 10 15 0 5 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 10 15 130 135 140 145 150 155 160 165 170 3
4
Assembly Instructions Step 1 1. Into the Edges of x Cross Plinths 3 insert a total of 8 x Dowels C. Locate Side Panels 1 and onto Cross Plinths as shown 3 1 3 Step 1.Slide Back Panel 4 position into 3 1 4 5
Assembly Instructions Step 3 1. Into Top and Bottom Panels 7 and 88 insert a total of 8 x Male Camlocks A C as shown. Into holes shown in Side Panels 31 and 4 Insert a total of 8 x Female Camlocks B as shown. Use a screwdriver to turn the Female Camlocks Clockwise to lock 7 For more information refer to the Using Camlocks Section 1 8 Step 4 8 1. On the reverse of the unit install a total of 4 x Panel Stiffeners as shown using 4 x Screw E E 6.
Assembly Instructions Step 5 1. Install Push Catch to Base Panel 8 as shown using 4 x Screw E. Connect Door Panel 55 to Right Side Panel as shown with x Hinges I I using a total for 8 x Screws FF 7 5 Step 6 1. To mount the unit to the wall 4 x holes will need to be drilled. Note: Please refer to the wall mounting guide at the back of this instruction for further details. 8. With the aid of someone, lift the unit into the desired position and mark the with a suitable scribe. Please use a spirit lebel to ensure your marks are level before any holes are drilled 3. Drill holes and insert 4 x suitable Wall Plugs, Please check the type of wall you are fixing to and for more information please see the guide to wall mounting & Fixings on the back page 4. With the aid of someone else. Hold the unit in position and using x suitable screws, attach the unit to the wall. 7
Assembly Instructions Step 7 1. Insert 4 x Shelf Supports D into the unit. Place Shelf 6 5 onto Shelf Supports 7 Assembly Complete 5 6 8