Playful Platform 29' 29' - PDF Free Download

R PB 8270 Playful Platform TM check out http://www.swing-n-slide.com/planupdates.htm for updates to these instructions. Option #1 PB 8263 Swing Beam PB 8270 Platform NE 4675L Slide 29' Option #2 PB 8263 Swing Beam PB 8270 Platform PB 8260 Tower PB 8264 Rock Wall PB 8265 Wood Roof NE 4675L Slide PAGES 8-28 22' No. of Children: Up to 6 Min. Use Zone: 29' x 22' Set Dim. 12'W x 10'L x 9'H Est. Building Time: 2 hrs. (Tower only.) 29' PAGES 29-49 ASSEMBLY INSTRUCTIONS 26' No. of Children: Up to 10 Min. Use Zone: 29' x 26' Set Dim. 12'W x 14'L x 10'H Est. Building Time: 2 hrs (Tower only.) Swing N Slide 1212 Barberry Drive Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232

R Safety Checklist for Swing-N-Slide Play Sets and Accessories Observing the following statements and warnings reduces the likelihood of serious or fatal injury Installation Safety Have You: Consulted the assembly instructions supplied with your particular model? Noted this accessory is to be used only on Swing N Slide approved designs? (Do not alter its design or add/remove components.) Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.) Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with a metal file as needed? Placed the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires? Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall onto a hard surface can result in serious injury to the equipment user.) Verified that suspended climbing ropes, chain,or cable are secured at both ends? Consulted in assembly instructions of your particular model for minimum use zones? Followed all anchoring and shock absorbing surfacing requirements on the back of this sheet as they apply? Made sure not to allow children to use equipment until it is properly installed? Operating Safety Have You: Determined that on-site adult supervision is provided for children of all ages? Warned children the following before allowing them to use the equipment? Not to walk close to, in front of, behind or between moving items. Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the strength of chain or rope. Not to swing empty seats or other accessories. Be sure to sit in the center of the swing seat and other accessories with full weight on the seat. Not to attach items to the playground equipment that are not specifically designed for use with the equipment such as but not limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard. Not to use equipment in a manner other than intended. Not to get off equipment while it is in motion. Not to climb on the equipment when it is wet. Determined that only one child per planned occupant seat should be allowed on this set at one time. Determined children must be dressed appropriately for play. Avoid clothing with draw strings and loose fitting clothes which could become entangled or snagged on equipment. Determined that suspended climbing ropes, chain, or cable cannot be looped back upon itself. Read and understood the following warning regarding the use of two and four passenger lawn swings? Warning: Lawn Swings are designed for use by children over two years of age. Use by children under the age of two can result in entrapment between the seats and back areas. Never place children in a rearward facing position or with legs between the seat and backrest because the child s body may pass through the opening causing entrapment of the child s head. Safety Maintenance Have You Determined to: Check all nuts and bolts twice monthly during the usage season for tightness and tighten as required? (It is particularly important that this procedure be followed at the beginning of each season.) To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories and take indoors? (Do not use when the temperature drops below 0 F.) Oil all metallic moving parts monthly during usage period? Check all hardware and equipment for sharp edges twice monthly during usage season? (Replace when necessary. It is especially important to do this at the beginning of each new season.) Check swing seats, chains, ropes and cables monthly during usage season for evidence of deterioration? Severe rusting or excessive wear, especially near the top swing hanger or at the seat connection are evidence of chain deterioration. Cracks in the protective plastic sleeve or seat itself are also signs of deterioration. If any of these conditions exist, call 1-800-888-1232 to order replacement accessories. Sand rusted metal parts and repaint using non-lead based paint. Disposal Instructions When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted. 2

This product is intended for single family home/residential use only and not intended for use in any public setting. Placement in any public setting constitutes a misuse of this product. IMPORTANT! ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions permit stakes to be pulled out easily, cementing into ground is necessary. To anchor the unit to the ground, Follow the instructions included in this plan for applying Anchor-It devices to your unit, or use 2" x 4" x 18" (45mm x 95mm x 457mm) pressuretreated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and climbing unit posts). Attach with four (4) 16D (3-1/2") galvanized nails per stake into each 4" x 4" (95mm x 95mm) post. If the unit has a climbing rope, anchor the rope end. Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material must be installed. This may be accomplished by using loose-fill materials at a sufficient depth. The Consumer Product Safety Commission Handbook for Public Playground Safety lists the following materials and required depths that are sufficient for home/residential application. For fall height protection up to 9 ft. (2.742m) [recommended for Swing N Slide kits]: LOOSE FILL MATERIAL REQUIRED (UNCOMPRESSED) DEPTH 1 in. (mm) Wood Mulch 9" (229mm) Double Shredded Bark Mulch 9" (229mm) Uniform Wood Chips 12" (305mm) Fine Sand 12" (305mm) Fine Gravel 12" (305mm) These depths were derived from the CPSC Handbook. Swing N Slide has not done independent tests to determine these required depths. When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units. This protective surfacing must extend a minimum of 6 ft. (1.828m) in all directions from the perimeter of the equipment or from the outermost edges of any component. For example, a slide extending beyond the platform must have protective surfacing at least 6 ft. (1.828mm) out from both sides as well as the end. For swings, the protective surface must extend at least 14 ft. (6m) out from both the back and front of the swing when the swing is in its rest position. Notes: 3

TOOLS REQUIRED HERRAMIENTAS REQUERIDAS OUTILS REQUIS TOOLS REQUIRED ELECTRIC DRILL 1/2" SOCKET & WRENCH HAMMER TAPE MEASURE SAFETY GLASSES & DUST MASK PHILLIPS BIT CARPENTER'S SQUARE (2) 1/2'' Panhead Screw (16) 2'' Lag Screw (4) 3/4'' Panhead Screw (2) 1-3/4'' Panhead Screw (4) 1-1/2'' Lag Bolt (1) T20 Torx Bit (6) 1-1/4'' Wood Screw (2) 1/4'' Flat Washer (54) 2'' Wood Screw (4) 5/16'' Flat Washer (96) 2-1/2'' Wood Screw (1) T30 Torx Bit (18) 1-1/4'' Lag Screw (4) Tarp Washer 4

R (2) EZ Frame Brace (R) (3) 'L' Bracket (2) EZ Frame Brace (L) THIS PRODUCT IS INTENDED FOR USE BY CHILDREN FROM AGES 2-10 YEARS For Home / Residential Use ONLY 1212 Barberry Drive Janesville, WI 53545 1-800-888-1232 www.swing-n-slide.com (1) Play Handle (1) PlayfulPlatform Tarp (1) Name Plate (4) Anchor-Its (4) Anchor-It Straps Playful Platform Plan (1) Plan 5

Platform Board List (1) 1 x 4 x 18 (1) 1 x 4 x 19 (12) 1 x 4 x 21 (1) 1 x 4 x 24 (2) 1 x 4 x 27 Angle Cut NOM INAL M ATERIAL SIZE LISTED SIZE T RUE SIZE English(*) Metric(Cm) English(*) Metric(Cm) 1x4 2.5x7.6 3/4x3-1/2 1.9x9 1x6 2.5x15.3 3/4x5-1/2 1.9x14 5/4x4 3.2x10.2 1x3-1/2 2.5x9 5/4x6 3.2x15.3 1x5-1/2 2.5x14 2x2 5x5 1-1/2x1-1/2 3.8x3.8 2x3 5x7.6 1-1/2x2-1/2 3.8x6.4 2x4 5x10 1-1/2x3-1/2 3.8x9 2x6 5x15.3 1-1/2x5-1/2 3.8x14 3x3 7.6x7.6 3 x3 7.6x7.6 4x4 10x10 3-1/2x3-1/2 9x9 (*) Estimated Sizing Due to Cutting Process (1) 5/4 x 4 x 10 Angle Cut (2) 5/4 x 4 x 16 (3) 5/4 x 4 x 24 (1) 2 x 4 x 13-5/8 (2) 2 x 4 x 18 (2) 2 x 4 x 46 (4) 2 x 4 x 94 (1) 2 x 4 x 12 Slide Stake (2) 5/4 x 2-1/2 x 19 (2) 5/4 x 2-1/2 x 48 (1) 4 x 4 x 10 Angle Cut 6

How to select the correct fastener Use these 2 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them. 1'' x 4'' to 2'' x 4'' Playful Platform Assembly Instructions (3) 2'' screws Apply 2" screws to the 1'' x 4'' boards when attaching to 2'' x 4'' uprights. 1'' x 4'' to 1'' x 4'' (2) 1-1/4'' screws Use 1-1/4'' screws when mounting 1'' x 4'' boards to 1''x4'' boards. 7

OPTION 1 INSTRUCTIONS Fig. 1 (3) 2'' screws Note: Screws Must Be Driven Through 5/4'' x 4'' Into The 2'' x 4''. 5/4'' x 4'' x 10'' Angle NOTE: Double check your measurements to make sure the structure is square. (3) 2'' screws 1'' x 4'' x 27'' Angle (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 1 Frame Assembly: 2'' Wood Screw 1. Install (1) 5/4'' x 4'', (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 1). 2-1/2'' Wood Screw 8

Fig. 2 NOTE: Double check your measurements to make sure the structure is square. (3) 2'' screws 1'' x 4'' x 27'' Angle (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 2 Frame Assembly Cont.: 2'' Wood Screw 1. Install (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 2). 2-1/2'' Wood Screw 9

Fig. 3 2'' x 4'' x 13-5/8'' Angle (3) 2-1/2'' screws 86'' Frame 2 Frame Assembly Cont.: 1. Install (1) 2'' x 4'' as shown in (Fig. 3). 2-1/2'' Wood Screw 10

Fig. 4 (3) 1-1/4'' Lag screws 3 5/8 3-5/8'' Frame 2 Swing Beam Support: 1. Install Swing Support Bracket as shown in (Fig. 4). 1-1/4'' Lag Screw 11

Fig. 5 (4) 2'' Lag screws per Bracket 3'' Center Brackets on 4'' x 4'' x 10'' Double check to make sure structure is square 4'' x 4'' x 10'' Angle Fig. 5a (3) 2-1/2'' wood screws 4'' x 4'' x 10'' Angle Fig. 5b (3) 1-1/4'' Lag screws UNDERSIDE VIEW Frame 2 2-1/2'' Wood Screw 2'' Lag Screw Swing Beam Support Cont.: 1. Attach (2) Swing beam Brackets as shown in (Fig. 5). 2. Secure Assembly in place on Frame as shown in (Fig. 5a). 3. Finish securing Assembly in place with 'L' Bracket as shown in (Fig. 5b). 1-1/4'' Lag Screw 12

DETAIL VIEW UNIT ROTATED 180 Fig. 6a (2) 2-1/2'' wood screws 5/4'' x 4'' x 24'' Double check to make sure structure is square 10-3/4'' Fig. 6 5/4'' x 4'' x 24'' 10'' 2'' x 4'' x 18'' 2'' x 4'' x 18'' (2) 2-1/2'' wood screws 10'' Frame 1 1'' x 4'' x 24'' (2) 2-1/2'' wood screws Install Frame Braces: 2-1/2'' Wood Screw 1. Install (1) 1'' x 4'', (1) 5/4'' x 4'', and (2) 2'' x 4'' boards as shown in (Fig. 6), and (Fig. 6a). 13

Fig. 7 (2) 2-1/2'' wood screws 2-1/2'' Wood Screw Platform Assembly: 1. Lift second half of Platform and secure in place in (4) locations as shown in (Fig. 7). 14

Fig. 8 (2) 2-1/2'' wood screws (12) 1'' x 4'' x 21'' NOTE: There must be a 3/8'' Nominal Gap between deck boards. Install Deck: 2-1/2'' Wood Screw 1. Install Deck boards, evenly spaced with a 3/8'' Gap, as shown in (Fig. 8). 15

Fig. 9 NOTE: Double check your measurements to make sure the boards are square. (2) 2-1/2'' wood screws (2) 5/4'' x 4'' x 24'' 24-1/4'' 37-3/4'' Install Step Rungs: 1. Install Step Rungs as shown in (Fig. 9). 2-1/2'' Wood Screw 16

Fig. 10 1-1/2'' 92-1/2'' PB 8263 Swing Beam Hole Locations 5 87-1/2'' 1. Tap Wood Loc Washer and Carriage Bolt into swing beam at locations shown in (Fig. 10). 8 7/8 3 3/4 78-5/8'' 74-7/8'' Fig. 10a 101/4 3 3/4 64-5/8'' 60-7/8'' 6-1/2'' CARRIAGE BOLT 7 1/4 53-5/8'' 3'' x 5-1/2'' Swing Beam WOOD LOC WASHER 3 3/4 49-7/8'' 94'' 121/4 37-5/8'' 3 3/4 33-7/8'' 7 1/4 3 3/4 26-5/8'' 22-7/8'' 101/4 12-5/8'' 3 3/4 8-7/8'' 8-7/8'' 3-1/2'' 17

Fig. 11 3'' x 5-1/2'' Swing Beam WASHER LOC-NUT WASHER LOC-NUT Swing Beam Drill Locations 1. Flip 3'' x 5-1/2'' Swing Beam so Carriage Bolts point downward as shown in (Fig. 11). 2. Install the swing hanger onto the beam by sliding over two carriage bolts (refer to (Fig. 10) for placement) and apply two washers and two loc-nuts per Swing Hanger. Make certain to orient swing hanger as shown in (Fig 11). Note: When attaching D-Ring, make certain threads are pointing up. This will help keep the D-Ring from loosening over time. 3. Repeat for all four hangers. Note: Examine all hardware after the loc-nuts are fully tightened. If more than two threads are exposed, cut the excess bolt off with a hacksaw or other suitable cutting tool. 18

Fig. 12 3-1/2'' FACE (8) 2-1/2 Screws A-Frame Assembly Align the edges of the 3" x 3-1/2" legs with the edges of EZ Frame Bracket 3-1/2'' FACE 3'' FACE 1. layout 3'' x 3-1/2 s and 2'' x 4'' as shown in (Fig. 12). 2. Align EZ Frame Bracket with face of 3'' x 3-1/2''s. 3. Secure EZ Frame Bracket with (8) 2-1/2'' screws to 3'' x 3-1/2''s making sure they are flush with each other. 4. Secure 2'' x 4'' to 3'' x 3-1/2''s as shown in (Fig. 12a). 5. Flip over and add 2nd bracket. Repeat steps 2 and 3. Fig. 12a EZ Frame Bracket 3" x 3-1/2" x 94'' 3" x 3-1/2" x 94'' (4) 2-1/2'' screws (4) 2-1/2'' screws 2" x 4" x 47-1/2" 3-1/2'' FACE 49-1/2" 92-5/8" 2-1/2'' screw 19

Fig. 13 Washer 2-1/2'' screws Loc-Nut 2-1/2'' screw A-Frame Assembly cont. 1. Align EZ-Frame Bracket with carriage bolts on Swing Beam as shown in (Fig. 13). 2. Attach A-Frame beam to Swing Beam using (2) washers and (2) Loc-Nuts and (2) screws as shown in (Fig. 13). 3. Tighten Loc-Nut. Repeat on other bracket. Note: Examine all hardware after the loc-nuts are fully tightened. If more than two threads are exposed, cut the excess bolt off with a hacksaw or other suitable cutting tool. 20

A-Frame Assembly cont. 1. With the help of others, lift A-Frame and Swing Beam Assembly and center onto unit as shown in (Fig. 14). 2. Secure Swing Beam with Hardware shown in (Fig. 14a). Fig. 14 Swing Beam Fig. 14a Swing Beam View from Deck 2'' Lag screw x 4 (each bracket) 21

Fig. 15 (4) 2'' Lag Screws AND (4) 2'' wood screws per Brace (2) Braces per side of unit Install EZ-Frame Braces: 2'' Wood Screw 1. Install (2) EZ-Frame Braces per side of the units as shown in (Fig. 15). 2'' Lag Screw 22

22-1/2'' Playful Platform Assembly Instructions Fig. 16 Double check to make sure boards are square 5/4'' x 2-1/2'' x 48'' 5/4'' x 2-1/2'' x 48'' (2) 2'' wood screws per side FLUSH Secure Tarp Supports: 1. Secure Tarp Supports as shown in (Fig. 16). 2'' Wood Screw 23

(2) 2'' wood screws Fig. 17 5/4'' x 2-1/2'' x 19'' (2) 2'' wood screws 5/4'' x 2-1/2'' x 19'' Tarp Support Installation Cont.: 2'' Wood Screw 1. Install Tarp support Cross Braces as shown in (Fig. 17). 24

22-1/4'' Playful Platform Assembly Instructions Fig. 18 (2) 5/4'' x 4'' x 16'' (2) 2'' wood screws Double check to make sure boards are square 22-1/4'' Fig. 18a (2) 2'' wood screws 1'' x 4'' x 19'' Tarp Support Braces Cont.: 1. Install Vertical Tarp Supports and Cross Brace as shown in (Fig. 18) and (Fig. 18a). 2'' Wood Screw 25

Fig. 19a Fig. 19 Washer 3/4'' Screw 2 Per Side Fig. 19b 1'' x 4'' x 18'' (4) 1-1/4'' wood screws Secure Tarp and Slide Support: 1-1/4'' Wood Screw 1. Secure Tarp in Place as shown in (Fig. 19), and (Fig. 19a). 2. Secure Slide Support in place as shown in (Fig. 19b). 3/4'' screw 26

Slide Installation. 1. Install Slide centered in the provided opening as shown in (Fig. 20). 2. Attach Stake to end of slide as shown in (Fig. 20a). Fig. 20 Fig. 20a (2) 1-1/4'' screws 2'' x 4'' x 12'' 2'' Above Ground 1'' Truss Screw Use truss head screws to to secure slide to deck. Anchor-It Fig. 21 metal strap Flat Washer 1-1/2" lag bolt Anchor-It Installation. Instructions for Anchoring Swing N Slide Activity Centers 1. Determine the final location of your activity center. 2. Place the Anchor-It stakes adjacent to the base and near the corners of your activity center (at the bottom of the legs on swing sets) and twist the auger-style stakes into the ground until only the loop is exposed. 3. Place the metal strap through the loop of the Anchor-It stake and secure it to the unit with a lag screw and washer as illustrated to the right. Note: Attach the strap to the unit with as little play as possible using whatever holes in the strap that work best. Anchor-It 27

R Playful Platform Assembly Instructions Fig. 22 1-1/4'' Screw THIS PRODUCT IS INTENDED FOR USE BY CHILDREN FROM AGES 2-10 YEARS For Home / Residential Use ONLY 1212 Barberry Drive Janesville, WI 53545 1-800-888-1232 www ID TAG: 1. Secure your product ID tag onto easy to read location of any 4'' x 4'' using (2) 1-1/2'' screws as shown in (Fig. 22). Safety Handle Fig. 22a Safety Handle: 1. Mount safety handle in the climber openings approximately 11'' above the deck surface (Fig. 22a). 1-3/4 Panhead screw washer 11" Deck Surface 1-3/4 Panhead screw 28

OPTION 2 INSTRUCTIONS Fig. 1 (3) 2'' screws Note: Screws Must Be Driven Through 5/4'' x 4'' Into The 2'' x 4''. (3) 2'' screws 5/4'' x 4'' x 10'' Angle 1'' x 4'' x 27'' Angle NOTE: Double check your measurements to make sure the structure is square. (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 1 Frame Assembly: 2'' Wood Screw 1. Install (1) 5/4'' x 4'', (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 1). 2-1/2'' Wood Screw 29

NOTE: Double check your measurements to make sure the structure is square. Fig. 2 (3) 2'' screws 1'' x 4'' x 27'' Angle (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 2 Frame Assembly Cont.: 1. Install (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 2). 2'' Wood Screw 2-1/2'' Wood Screw 30

Fig. 3 2'' x 4'' x 13-5/8'' Angle (3) 2-1/2'' screws 86'' Frame 2 Frame Assembly Cont.: 1. Install (1) 2'' x 4'' as shown in (Fig. 3). 2-1/2'' Wood Screw 31

Fig. 4 (3) 1-1/4'' Lag screws 3 5/8 3-5/8'' Frame 2 Swing Beam Support: 1. Install Swing Support Bracket as shown in (Fig. 4). 1-1/4'' Lag Screw 32

Fig. 5 3'' (3) 1-1/4'' Lag screws per Bracket 4'' x 4'' x 10'' Angle Fig. 5a (3) 2-1/2'' wood screws 4'' x 4'' x 10'' Angle Fig. 5b (3) 1-1/4'' Lag screws UNDERSIDE VIEW Frame 2 Swing Beam Support Cont.: 2-1/2'' Wood Screw 1. Attach (2) L Brackets as shown in (Fig. 5). 2. Secure Assembly in place on Frame as shown in (Fig. 5a). 3. Finish securing Assembly in place with Metal Bracket as shown in (Fig. 5b). 1-1/4'' Lag Screw 33

DETAIL VIEW UNIT ROTATED 180 (2) 2-1/2'' wood screws 5/4'' x 4'' x 24'' Fig. 6a Double check to make sure structure is square Fig. 6 10-3/4'' 5/4'' x 4'' x 24'' 10'' 2'' x 4'' x 18'' 2'' x 4'' x 18'' 10'' (2) 2-1/2'' wood screws Frame 1 (2) 2-1/2'' wood screws 1'' x 4'' x 24'' Install Frame Braces: 2-1/2'' Wood Screw 1. Install (1) 1'' x 4'', (1) 5/4'' x 4'', and (2) 2'' x 4'' boards as shown in (Fig. 6), and (Fig. 6a). 34

Fig. 7 (2) 2-1/2'' wood screws Platform Assembly: 2-1/2'' Wood Screw 1. Lift second half of Platform and secure in place in (4) locations as shown in (Fig. 7). 35

Fig. 10 Remove Existing A-Frame: 1. IF You already have the A-Frame on your Tower Swing Beam assembled, remove it along with the (2) E-Z Frame Brackets attached. Support the Swing Beam with a Ladder or with the help of an assistant until the Playful Platform can be manueverd in place. 38

Swing Beam Attachment cont. 1. With the help of others, position Swing Beam on Brackets and center onto unit as shown in (Fig. 11). 2. Secure as shown in (Fig 11a). Fig. 11 Swing Beam Fig. 11a Swing Beam View from Deck 1-1/4'' Lag Screw x 3 (each bracket) 39

Fig. 12 (4) 2'' Lag Screws AND (4) 2'' wood screws per Brace (1) Brace per side of unit Install EZ-Frame Braces: 2'' Wood Screw 1. Install (1) EZ-Frame Braces per side of the units as shown in (Fig. 12). 2'' Lag Screw 40

22-1/2'' Playful Platform Assembly Instructions Fig. 13 Double check to make sure boards are square 5/4'' x 2-1/2'' x 48'' 5/4'' x 2-1/2'' x 48'' FLUSH (2) 2'' wood screws per side Secure Tarp Supports: 1. Secure Tarp Supports as shown in (Fig. 13). 2'' Wood Screw 41

Fig. 14 (2) 2'' wood screws 5/4'' x 2-1/2'' x 19'' 5/4'' x 2-1/2'' x 19'' (2) 2'' wood screws Tarp Support Installation Cont.: 1. Install Tarp support Cross Braces as shown in (Fig. 14). 2'' Wood Screw 42

22-1/4'' 22-1/4'' Playful Platform Assembly Instructions Fig. 15 Double check to make sure boards are square (2) 5/4'' x 4'' x 16'' (2) 2'' wood screws Tarp Support Braces Cont.: 2'' Wood Screw 1. Install Vertical Tarp Supports as shown in (Fig. 15). 43

Fig. 16 (2) 2'' wood screws 1'' x 4'' x 19'' Tarp Support Braces Cont.: 1. Install Tarp Cross Brace as shown in (Fig. 16). 2'' Wood Screw 44

Fig. 17a Fig. 17 Washer 3/4'' Screw 2 Per Side Secure Tarp: 1. Secure Tarp in Place as shown in (Fig. 17), and (Fig. 17a). 3/4'' screw 45

Fig. 18 1'' x 4'' x 18'' (4) 1-1/4'' wood screws Secure Deck Support: 1. Secure 1'' x 4'' x 18'' Deck Support Board under the Platform Deck as shown in (Fig. 18). 1-1/4'' Wood Screw 46

2'' x 4'' x 56-3/4'' 2'' x 4'' x 56-3/4'' Playful Platform Assembly Instructions THESE INSTRUCTIONS SUPERCEDE THE PLAN INCLUDED WITH YOUR ROCK WALL KIT Fig. 19 Fig. 19a (16) 1'' x 4'' x 24'' (2) 2-1/2'' screws 3/4'' 21'' 1-1/2'' (2) 2-1/2'' screws (2) 2-1/2'' screws Rock Wall Assembly and Installation: 1. Assemble Rock as shown in (Fig. 19). 2. Install Rock wall on Unit as shown in (Fig. 19a). 2-1/2'' Wood Screw 47

Fig. 20 Hold (rock) (2)"T" nuts Climbing Rock Installation 1. Mark locations of Climbing Rocks on the Climbing Wall in a pattern that will easily allow your child to climb to the deck. Make sure the bolt hole locations are clear of wall supports before drilling. 2. Drill holes through the wall at the desired locations using a 3/8" drill bit. Install Climbing Rocks as shown in (Fig. 20). 3. Make sure the Climbing Wall and Climbing Rock connections are secure before allowing any children to play on the Climbing Wall. 3/8" Holes (2) 1-1/4'' Hex Head Bolts (1) Loc Washer per bolt (1) Flat Washer per bolt Fig. 21 metal strap Flat Washer 1-1/2" lag bolt Anchor-It Anchor-It Installation. Instructions for Anchoring Swing N Slide Activity Centers 1. Determine the final location of your activity center. 2. Place the Anchor-It stakes adjacent to the base and near the corners of your activity center (at the bottom of the legs on swing sets) and twist the auger-style stakes into the ground until only the loop is exposed. 3. Place the metal strap through the loop of the Anchor-It stake and secure it to the unit with a lag screw and washer as illustrated to the right. Note: Attach the strap to the unit with as little play as possible using whatever holes in the strap that work best. Anchor-It 48

Questions???... Call our Customer Service Department at 1-800-888-1232 R PlayCore Inc. 2009 Printed In USA LA 6046

PB 8263 Swing Beam Kit check out http://www.swing-n-slide.com/planupdates.html for updates to these instructions For more information, visit this link: http://www.swing-n-slide.com 28' Minimum Safe Use Zone ASSEMBLY INSTRUCTIONS Swing N Slide 1212 Barberry Drive Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232

TOOLS REQUIRED TAPE MEASURE HAMMER CARPENTER'S SQUARE ELECTRIC DRILL (1) T20 & T30 Torx Bit SAFETY GLASSES & DUST MASK (2) Split Beam bracket (2) Wrap-Loc (2) 3X3 TO 4X4 Shelf-Loc (2) EZ Frame Brackets (28) 2-1/2'' screws (28) 2" lag screw (2) 5/16''Hex Head Lag Screws (14) 6-1/2'' Bolts (14) 5/16'' flat washers (14) Loc-Nuts (14) Wood Loc Washers 4

Swing Beam Assembly Instructions BOARD LIST (1) 2'' x 4'' x 47-1/2'' (1) 4'' x 4'' x 47-1/2'' (2) 3'' x 3-1/2'' x 94'' (1) 3'' x 5-1/2'' x 94'' (1) Ring-Trap Combo (2) Extra Duty-Swing Seats (6) Extra-Duty Swing Hangers Swing Beam Plan (2) Anchor-It Straps (2) Anchor-It (1) Plan 5

Swing Beam Assembly Instructions Fig. 1 Fig. 2 84-1/2'' (1) 2'' Lag Screws Per Bracket 84-1/2'' (2) 2'' Lag Screws Per Bracket Fig. 2a (2) 2'' Lag Screws Tip: Flex brackets to make installation of 4'' x 4'' easier Fig.2b Approx. 1/4'' Fig. 3 (5) 2'' Lag Screws Per Bracket 4" x 4" x 47-1/2" A. Swing Beam Support 1. Attach the Swing Beam Kit on the side of the tower illustrated in (Fig. 1). Make certain you have provided for the Minimum Safe Use Zone. 2. Attach Wrap Brackets to Uprights as shown in (Fig. 1). Use only one (1) 2'' Lag Screw to hold bracket in place. 3. AttachShelf Brackets to Wrap Brackets as shown in (Fig. 2). Use only two (2) 2'' Lag Screws to attach brackets as shown in (Fig. 2a). 4. Spread open Shelf Brackets as shown in (Fig. 2b). Slide 4'' x 4'' into brackets and secure as shown in (Fig. 3). 2'' Lag screw 6

Swing Beam Assembly Instructions Fig. 4 A-FRAME 1-1/2'' 92-1/2'' B. Swing Beam Hole Locations 5 87-1/2'' 1. Tap Wood Loc Washer and Carriage Bolt into swing beam at locations shown in (Fig. 4a). 8 7/8 3 3/4 78-5/8'' 74-7/8'' 101/4 3 3/4 64-5/8'' 60-7/8'' Fig. 4a 7 1/4 53-5/8'' 6-1/2'' CARRIAGE BOLT 3 3/4 49-7/8'' 94'' WOOD LOC WASHER 121/4 3'' x 5-1/2'' Swing Beam 37-5/8'' 3 3/4 33-7/8'' 7 1/4 3 3/4 26-5/8'' 22-7/8'' 101/4 12-5/8'' 3 3/4 8-7/8'' 8-7/8'' 3'' 3-1/2'' 7

Swing Beam Assembly Instructions Fig. 5 4'' x 6'' Swing Beam WASHER LOC-NUT WASHER D-RINGS LOC-NUT C. Swing Beam Drill Locations 1. Flip 3'' x 5-1/2'' Swing Beam so Carriage Bolts point downward as shown in (Fig. 5). 2. Install the swing hanger onto the beam by sliding over two carriage bolts (refer to (Fig. 4) for placement) and apply two washers and two loc-nuts per Swing Hanger. Make certain to orient swing hanger as shown in (Fig 5). Note: When attaching D-Ring, make certain threads are pointing up. This will help keep the D-Ring from loosening over time. 4. Repeat for all six hangers. 8

Swing Beam Assembly Instructions Fig. 6 3-1/2'' FACE (8) 2-1/2 Screws D. A-Frame Assembly Align the edges of the 3" x 3-1/2" legs with the edges of EZ Frame Bracket 3-1/2'' FACE 3'' FACE 1. layout 3'' x 3-1/2 s and 2'' x 4'' as shown in (Fig. 6). 2. Align EZ Frame Bracket with face of 3'' x 3-1/2''s. 3. Secure EZ Frame Bracket with (8) 2-1/2'' screws to 3'' x 3-1/2''s making sure they are flush with each other. 4. Secure 2'' x 4'' to 3'' x 3-1/2''s as shown in (Fig. 6a). 5. Flip over and add 2nd bracket. Repeat steps 2 and 3. Fig. 6a EZ Frame Bracket 3" x 3-1/2" x 94'' 3" x 3-1/2" x 94'' (4) 2-1/2'' screws (4) 2-1/2'' screws 2" x 4" x 47-1/2" 3-1/2'' FACE 49-1/2" 93" 2-1/2'' screw 9

Swing Beam Assembly Instructions Fig. 7 Washer 2-1/2'' screws Loc-Nut 2-1/2'' screw E. A-Frame Assembly cont. 1. Align EZ-Frame Bracket with carriage bolts on Swing Beam as shown in (Fig. 7). 2. Attach A-Frame beam to Swing Beam using (2) washers and (2) Loc-Nuts and 2 screws as shown in (Fig. 7). 3. Tighten Loc-Nut. Repeat on other bracket. 10

Swing Beam Assembly Instructions F. A-Frame Assembly cont. Fig. 8 1. Position Split-Brackets on 4'' x 4'' x 47-1/2'' as shown in (Fig. 8). 2. With the help of others, lift A-Frame and Swing Beam Assembly and center onto unit as shown in (Fig. 8a). 3. Secure as shown in (Fig 8a). Swing Beam 22'' Fig. 8a Swing Beam View from Deck 2'' Lag screw x 8 (each bracket) 11

Swing Beam Assembly Instructions Fig. 9 G. Attach Swings onto Swing Hangers 1. Attach the end link of each Swing Chain to one Swing Hanger D Ring as shown in (Fig. 9). Make certain to secure each D Ring in the closed position by using an adjustable wrench. 12

Swing Beam Assembly Instructions Fig. 10 Fig. 11 H. Install Anchor-Its 1. (1) Anchor-It must be installed on each leg of the Swing Beam. 2. Screw a Anchor-It into the ground near each leg until only the triangular head remains as shown in (Fig. 10) and (Fig. 11). 3. Insert a strap through the head of theanchor-it. Align holes of strap as illustrated and attach to the unit using one 1-1/2" lag bolt and washer per Anchor-It. 13

Swing Beam Assembly Instructions 14

15 Swing Beam Assembly Instructions

Questions???... Call our Customer Service Department at 1-800-888-1232 PlayCore Inc. 2008 Printed In USA LA 5870

R PB 8285 check out http://www.swing-n-slide.com/planupdates.htm for updates to these instructions. Kit Components: PB 8263 Swing Beam PB 8270 Platform NE 4700-T Slide Assembly Instructions: PAGES 8-28 29' NOTE: PAGES 29-49 DO NOT APPLY TO THE PB 8285 DESIGN 22' No. of Children: Up to 6 Min. Use Zone: 29' x 22' Set Dim. 12'W x 10'L x 9'H Est. Building Time: 2 hrs. (Tower only.) ASSEMBLY INSTRUCTIONS Swing N Slide 1212 Barberry Drive Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232 PlayCore Inc. 2010 Printed In USA LA 6084

Assembly Instructions NOTE: THESE SLIDE INSTRUCTIONS REPLACE THOSE ON PAGE 27 OF YOUR ASSEMBLY PLAN. Fig. 20 Fig. 20a 1 2 5 11 3 6 10 4 7 8 9 Fig. 20b (22) 5/16'' loc-nut (44) 5/16'' flat washers Fig. 20c (2) 1-1/4'' screws 2'' x 4'' x 12'' 2'' Above Ground Summit Slide Installation. 1. Align Summit slide sections together on the ground. Begin attaching two Summit slide sections together by securing the two outer most bolts in place finger tight (see (Fig. 20a) for proper Bolt Sequence). Following this pattern install (1) bolt, (2) washers and (1) loc-nut per hole (see (Fig. 20b)). Once all (11) bolts, (22) flat washers and (11) loc-nuts are in place go back and tighten all hardware with appropriate tools. 2. Consult (Fig. 20) For proper placement of Summit slide on your unit. 3. Drive wood stake into ground leaving 2'' exposed. 4. Secure the Summit slide bottom to the stake using (2) 1-1/4'' deck screws. (Fig. 20C). 5. Attach Summit slide to unit as shown in (Fig. 20). PlayCore Inc. 2010 Printed In USA LA 6084 2