IP65 IP67 Ⅰ Ⅰ A D File Name:HVGSPEC 180413
SPECIFICATION MODEL HVG15 HVG HVG24 HVG30 HVG36 HVG42 HVG48 HVG54 DC VOLTAGE 15V V 24V 30V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.4 9~15V 10~V 12~24V 15~30V 18~36V 21~42V 24~48V 27~54V RATED CURRENT RATED POWER 5A 75W 4.8A 96W 4A 96W 3.2A 96W 2.65A 95.4W 2.28A 95.76W 2A 96W 1.77A 95.58W RIPPLE & NOISE (max.) Note.2 150mVpp 150mVpp 150mVpp 0mVpp 0mVpp 0mVpp 0mVpp 0mVpp OUTPUT VOLTAGE ADJ. RANGE Adjustable for A/ABType only (via the builtin potentiometer) 13.5 ~ 17V 17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 38 ~ 46V 43 ~ 53V 49 ~ 58V CURRENT ADJ. RANGE Adjustable for A/ABType only (via the builtin potentiometer) 2.75 ~ 5A 2.64 ~ 4.8A 2.2 ~ 4A 1.76 ~ 3.2A 1.45 ~ 2.65A 1.25 ~ 2.28A 1.1 ~ 2A 0.97 ~ 1.77A VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION LOAD REGULATION ±1.5% SETUP, RISE TIME Note.6 500ms, 80ms /230VAC, 347VAC, 480VAC HOLD UP TIME (Typ.) 30ms/347VAC, 480VAC VOLTAGE RANGE Note.5 180 ~ 528VAC 254VDC ~ 747VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE POWER FACTOR (Typ.) 47 ~ 63Hz PF 0.98/230VAC, PF 0.98/277VAC, PF 0.97/347VAC, PF 0.93/480VAC @full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< %(@ load 50%/230VAC, 277VAC, 347VAC [@ load 60% only for 15V model]; @ load 75%/480VAC) TOTAL HARMONIC DISTORTION INPUT (Please refer to TOTAL HARMONIC DISTORTION (THD) section) EFFICIENCY (Typ.) AC CURRENT (Typ.) 89% 0.38A / 347VAC 90% 91% 0.28A / 480VAC 91% 90.5% 90.5% 91% 91% INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER COLD START 25A(t width=900 μs measured at 50% I peak) at 480VAC; Per NEMA 410 5 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 480VAC LEAKAGE CURRENT <0.75mA / 480VAC OVER CURRENT 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION 18 ~ 21V 23 ~ 27V 28 ~ 34V 34 ~ 38V 41 ~ 46V OVER VOLTAGE Shut down o/p voltage with autorecovery or repower on to recovery 47 ~ 53V 54 ~ 60V 59 ~ 65V OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. Tcase=40 ~ 90 (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase=90 ENVIRONMENT WORKING HUMIDITY ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 60 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY & EMC OTHERS NOTE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION UL8750(type HL ), CSA C22.2 No. 250.008, EAC TP TC 004, IP65 or IP67 approved I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN6032 Class C (@ load 50% load, @ load 60% only for 15V model) ; EN6033, FCC Part 15 Subpart B, EAC TP TC 0 EMC IMMUNITY Compliance to EN6042,3,4,5,6,8,11, EN61547, light industry level ( surge immunity LineEarth 4KV, LineLine 2KV ), EAC TP TC 0 MTBF 174.9K hrs min. MILHDBK217F (25 ) DIMENSION 236**mm (L*W*H) PACKING 1.18Kg; 12pcs/15.2Kg/0.74CUFT File Name:HVGSPEC 180413
Block Diagram Fosc : 80KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. O.T.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. V V DIM DIM (B Type) DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current region Should there be any compatibility issues, please contact MEAN WELL. 50 Io (%) Typical output current normalized by rated current (%) File Name:HVGSPEC 180413
DIMMING OPERATION HVG DIM(Blue) DIM(White) V(Black) V(Red) 3 in 1 dimming function (for B/ABType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 0 ~ 10VDC % 90% Output current (%) 80% 70% 60% 50% 40% 30% % 10% 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Output current (%) % 90% 80% 70% 60% 50% 40% 30% % 10% 0% 0% 10% % 30% 40% 50% 60% 70% 80% 90% % Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM V V DIM Additive Voltage DIM DO NOT connect "DIM to V" Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" DIM DO NOT connect "DIM to V" Additive Resistance Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. Output current (%) % 90% 80% 70% 60% 50% 40% 30% % 10% 0% Short 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HVGSPEC 180413
OUTPUT LOAD vs TEMPERATURE 80 80 60 60 LOAD (%) 40 LOAD (%) 40 40 25 10 0 15 30 50 60 70 (HORIZONTAL) 40 25 0 45 55 65 75 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 80 1.00 Constant Current Mode 90 0.98 LOAD (%) 80 70 60 50 40 PF 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 480V 347V 277V 230V 180 347 440 480 528 INPUT VOLTAGE (V) 60Hz 0.80 50% 60% 70% 80% 90% % LOAD (W) TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD possess superior working efficiency that up to 91% can be reached in field applications. 48V Model, Tcase at 80 48V Model, Tcase at 80 25 0.96 0.92 0.88 THD(%) 15 10 5 230VAC 277VAC 347VAC 480VAC EFFICIENCY(%) 0.84 0.80 0.76 0.72 0. 0.64 480V 347V 277V 230V 0 50% 60% 70% 80% 90% % 0.60 10% % 30% 40% 50% 60% 70% 80% 90% % LOAD LOAD File Name:HVGSPEC 180413
LIFE TIME 1 80 LIFETIME(Kh) 60 40 0 30 40 50 60 70 80 90 Tc a s e ( ) File Name:HVGSPEC 180413
MECHANICAL SPECIFICATION AType Case No. 994 Unit:mm 236 12 9.6 9.4 34.2 9.4 34 Vo ADJ. 104.4 Io ADJ. V(Black) V(Red) ψ 4.2 4PL : Max. Case Temperature BType 236 12 9.6 9.4 34.2 9.4 34 104.4 V(Black) V(Red) UL2517 18AWG ψ 4.2 4PL DIM(Blue) DIM(White) : Max. Case Temperature File Name:HVGSPEC 180413
ABType 236 12 9.6 9.4 34.2 9.4 34 Vo ADJ. 104.4 Io ADJ. UL2517 18AWG ψ 4.2 4PL DIM(Blue) DIM(White) V(Black) V(Red) DType 12 9.6 236 9.4 9.4 34.2 104.4 ψ 4.2 4PL : Max. Case Temperature 34 V(Black) V(Red) : Max. Case Temperature File Name:HVGSPEC 180413
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HVG to operate in dry/wet/damp or outdoor environment. AC source I/P HVG O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4PIN 5A/PIN M1204 10A max. 5PIN 5A/PIN M1205 10A max. M15 Order No. Suitable Current 2PIN 12A/PIN M1502 12A max. LED Lamp Cable Joiner 66 26 CJ041 suitable for 14AWG~16AWG CJ042 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HVG O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ042. Junction Box Option 374 76 10 5 61 8.5 32 8.5 6 2ψ5 3 PF 1/2" 150± 35 V(Black) V(Red) 3 PF 1/2" 150± Optional junction box available for A type, please contact MEAW WELL for details. 86 INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html File Name:HVGSPEC 180413