IP65 IP67 Metal housing with class I design Standby power consumption <0.5W at remote off Ⅰ current output. HLG600H operates from 90~305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to, with the fanless design, the entire series is able to operate for 40 ~ 90 case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HLG600H is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system. I B I File Name:HLG600HSPEC 170714
SPECIFICATION MODEL OUTPUT INPUT HLG600H12 HLG600H15 HLG600H HLG600H24 HLG600H30 HLG600H36 HLG600H42 HLG600H48 HLG600H54 DC VOLTAGE 12V 15V V 24V 30V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.4 6 ~12V 7.5 ~ 15V 10 ~ V 12 ~ 24V 15 ~ 30V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V RATED CURRENT 40A 36A 28A 25A A 16.7A 14.3A 12.5A 11.2A RATED POWER 480W 540W 560W 600W 600W 601.2W 600.6W 600W 604.8W RIPPLE & NOISE (max.) Note.2 150mVpp 150mVpp 150mVpp 150mVpp 0mVpp 250mVpp 250mVpp 250mVpp 350mVpp VOLTAGE ADJ. RANGE Adjustable for AType only (via builtin potentiometer) 10.2 ~ 12.6V 12.7 ~ 15.8V 17 ~ 21V.4 ~ 25.2V 25.5 ~ 31.5V 30.6 ~ 37.8V 35.7 ~ 44.1V 40.8 ~ 50.4V 45.9 ~ 56.7V CURRENT ADJ. RANGE Adjustable for AType only (via builtin potentiometer) ~ 40A 18 ~ 36A 14 ~ 28A 12.5 ~ 25A 10 ~ A 8.3 ~ 16.7A 7.1 ~ 14.3A 6.2 ~ 12.5A 5.6 ~ 11.2A VOLTAGE TOLERANCE Note.3 ±3.0% ±2.0% ±1.5% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% LOAD REGULATION ±2.0% ±1.5% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME Note.6 500ms, 80ms/ 115VAC, 230VAC HOLD UP TIME (Typ.) 15ms / 115VAC, 230VAC VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) Note.5 TOTAL HARMONIC DISTORTION EFFICIENCY 230VAC (Typ.) 277VAC AC CURRENT (Typ.) INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF 0.98/115VAC, PF 0.95/230VAC, PF 0.93/277VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< % (@ load 50% /115VAC, 230VAC; @ load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION (THD) section) 92% 93.5% 94.5% 95% 92.5% 93.5% 94.5% 95% 7A / 115VAC 3.3A / 230VAC 2.9A / 277VAC LEAKAGE CURRENT STANDBY POWER CONSUMPTION <0.75mA / 277VAC <0.5W at remote off OVER CURRENT Note.4 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION 13 ~ 16V 16.5 ~.5V 22 ~ 26V 26 ~ 30V 32.5 ~ 36.5V 39.5 ~ 43.5V OVER VOLTAGE Shut down o/p voltage, repower on to recover 46 ~ 50V 52.5 ~ 56.5V 59 ~ 63V OVER TEMPERATURE Shut down o/p voltage, repower on to recover FUNCTION REMOTE ON/OFF CONTROL Power on : "High" >2 ~ 5V or Open circuit Power off : "Low" <0 ~ 0.5V or Short circuit 5V STANDBY 5V SB : 5V@0.5A ; tolerance ± 5%, ripple : mvpp(max.) WORKING TEMP. Tcase= 40 ~ 90 (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase= 90 ENVIRONMENT WORKING HUMIDITY ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~ 85, 10 ~ 95% RH noncondensing TEMP. COEFFICIENT VIBRATION ± 0.03%/ (0 ~ 55 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.8 UL609501, UL8750(type HL ), CSA C22.2 No. 250.1312, ENEC EN613471, EN61347213 independent, EN62384, IP65 or IP67, J613471, J61347213 approved SAFETY & WITHSTAND VOLTAGE I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC EMC ISOLATION RESISTANCE I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH (Note 9) EMC EMISSION Note.8 Compliance to EN55015, EN6032 Class C (@ load 50% ) ; EN6033 EMC IMMUNITY Compliance to EN6042,3,4,5,6,8,11, EN61547, EN55024, light industry level ( surge immunity LineEarth 4KV, LineLine 2KV) MTBF 76.9K hrs min. MILHDBK217F (25 ) OTHERS DIMENSION 280*144*48.5mm (L*W*H) PACKING 3.9Kg; 4pcs/16.6Kg/0.9CUFT NOTE 95% 95% 95.5% 95.5% COLD START 70A(t width=0 μs measured at 50% I peak) at 230VAC; Per NEMA 410 1 unit (circuit breaker of type B) / 2 units (circuit breaker of type C) at 230VAC File Name:HLG600HSPEC 170714
BLOCK DIAGRAM 5VSB DETECTION CIRCUIT fosc : KHz(5V) 70KHz(12V~54V) POWER SWITCHING PWM CONTROL RECTIFIERS & FILTER 5VSB I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. V V DIM DIM (B Type) PS/ON CONTROL PS/ON DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current region Should there be any compatibility issues, please contact MEAN WELL. 50 Io (%) Typical output current normalized by rated current (%) File Name:HLG600HSPEC 170714
DIMMING OPERATION FG (Green/Yellow) AC/L(Brown) AC/N(Blue) HLG600H RC(Brown) RC & GND(Black) 5V SB(Yellow) DIM(Blue) DIM(White) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 0 ~ 10VDC % 90% Output current (%) 80% 70% 60% 50% 40% 30% % 10% 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Output current (%) % 90% 80% 70% 60% 50% 40% 30% % 10% 0% 0% 10% % 30% 40% 50% 60% 70% 80% 90% % Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM V V DIM Additive Voltage DIM DO NOT connect "DIM to V" Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" DIM DO NOT connect "DIM to V" Additive Resistance Output current (%) % 90% 80% 70% 60% 50% 40% 30% % 10% 0% Short 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance Note : 1. Min. dimming level is about 6% and the output current is not defined when 0%< Iout<6%. 2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. File Name:HLG600HSPEC 170714
OUTPUT LOAD vs TEMPERATURE 80 80 60 60 LOAD (%) 40 LOAD (%) 40 40 25 10 0 15 30 50 55 60 70 (HORIZONTAL) 40 25 0 45 55 65 75 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) If HLG600H operates in constant current mode with the rated current, the maximum workable Ta is 55. STATIC CHARACTERISTICS POWER FACTOR(PF) CHARACTERISTIC Tcase at 80 Constant Current Mode 90 1.00 0.98 0.96 80 0.94 LOAD (%) 70 60 50 40 PF 0.92 0.90 0.88 0.86 0.84 0.82 277V 230V 115V 0.80 90 115 125 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) 60Hz 0.78 50% 60% 70% 80% 90% % (600W) LOAD Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 80 16 14 EFFICIENCY vs LOAD possess superior working efficiency that up to can be reached in field applications. 48V Model, Tcase at 80 98 12 96 THD(%) 10 8 6 4 277VAC 230VAC 115VAC EFFICIENCY (%) 94 92 90 88 277V 230V 115V 2 86 0 84 50% 60% 70% 80% 90% % 10% % 30% 40% 50% 60% 70% 80% 90% % LOAD LOAD File Name:HLG600HSPEC 170714
LIFETIME 1 80 LIFETIME(Kh) 60 40 0 30 40 50 60 70 80 90 Tc a s e ( ) File Name:HLG600HSPEC 170714
MECHANICAL SPECIFICATION AType Case No. 228 Unit:mm 13.4 8.9 280 253.2 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) BType FG (Green/Yellow) AC/L(Brown) AC/N(Blue) SJTW 18AWG SJTW 18AWG 15 15 25± 2 13.4 8.9 25± 2 15 97 15 97 144 144 Tcase Tcase 47 47 tc : Max. Case Temperature tc : Max. Case Temperature tc 280 253.2 tc 126.6 Io ADJ. ADJ. Vo 126.6 UL2517 22AWG ψ 4.5 4PL LED 350± UL2517 22AWG UL2517 18AWG ψ 4.5 4PL RC(Brown) RC & GND(Black) 5V SB(Yellow) 48.5 48.5 RC(Brown) RC & GND(Black) 5V SB(Yellow) DIM(Blue) DIM(White) File Name:HLG600HSPEC 170714
BlankType 13.4 8.9 280 253.2 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) SJTW 18AWG 47 126.6 ψ 4.5 4PL RC(Brown) RC & GND(Black) 5V SB(Yellow) 25± 2 48.5 15 15 97 144 Tcase tc UL2517 22AWG tc : Max. Case Temperature INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html File Name:HLG600HSPEC 170714