Ⅰ IP65 IP67 A
SPECIFICATION MODEL HBG24024 HBG24036 HBG24048 HBG240 DC VOLTAGE 24V 36V 48V V CONSTANT CURRENT REGION Note.2 14.4 ~ 24V 21.6 ~ 36V 28.8 ~ 48V 36 ~ V RATED CURRENT 10A 6.7A 5A 4.0A RATED POWER Note.5 240W 240W 240W 240W RIPPLE & NOISE (max.) Note.3 150mVpp 250mVpp 250mVpp 350mVpp OUTPUT CURRENT ADJ. RANGE Adjustable for AType (via builtin potentiometer) 6 ~ 10A 4.0 ~ 6.7A 3 ~ 5A 2.4 ~ 4.0A VOLTAGE TOLERANCE Note.4 ±2.0% LINE REGULATION ±0.5% LOAD REGULATION ±0.5% SETUP, RISE TIME Note.6 500ms,1ms /230VAC 2500ms,1ms /115VAC HOLD UP TIME (Typ.) 15ms /115VAC, 230VAC VOLTAGE RANGE Note.5 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) INPUT PROTECTION OTHERS NOTE FREQUENCY RANGE POWER FACTOR EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT OVER CURRENT OVER VOLTAGE OVER TEMPERATURE WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC TOTAL HARMONIC DISTORTION SHORT CIRCUIT SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note. 8 47 ~ 63Hz PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC@ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< %(@load %/115VC,230VAC; @load 80%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) 92.5% 92.5% 93% 93.5% 2.5A / 115VAC 1.3A / 230VAC 1.2A / 277VAC COLD START 75A(twidth= 680μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 2 units (circuit breaker of type B) / 3 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 27 ~ 34V 43 ~ 52V 52 ~ 63V 62 ~ 85V Shut down and latch off o/p voltage, repower on to recover Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. Tcase=40 ~ 75 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=75 ~ 95% RH noncondensing 40 ~ 80, 10 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750,CSA C22.2 No.250.1312, ENEC EN613471, EN61347213 independent, EN62384; IP65 or IP67 approved I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:0.5KVAC I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN32 Class C (@load 75%) ; EN33 EMC IMMUNITY Compliance to EN42,3,4,5,6,8,11, EN61547,light industry level ( surge immunity:lineearth:4kv,lineline:2kv) MTBF 663.8K hrs min. Telcordia SR332 (Bellcore) ; 190.7Khrs min. MILHDBK217F (25 ) DIMENSION ψ191.5mm *69mm (D * H) PACKING 2.1Kg; 8pcs/18.3Kg/2.09CUFT
BLOCK DIAGRAM fosc : KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.L.P. V V FG PFC CONTROL O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (min.) (A) Constant Voltage area (C) Hiccup Protection (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 50 Io(%) Typical output current normalized by rated current (%)
DIMMING OPERATION AC/L(Brown) AC/N(Blue) FG (Green/Yellow) V(Red) V(Black) DIM(BLUE) DIM(WHITE) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) % 90% 80% 70% % 50% 40% 30% % 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Applying additive resistance: Output current (%) % 90% 80% 70% % 50% 40% 30% % 10% 10% % 30% 40% 50% % 70% 80% 90% % Duty cycle of additive 10V PWM signal dimming input V % 90% V DIM DIM DO NOT connect "DIM to V" Additive Resistance Output current (%) 80% 70% % 50% 40% 30% % 10% 10K/N K/N 30K/N 40K/N 50K/N K/N 70K/N 80K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HBG240CSPEC 1616
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HBG240 BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture.
OUTPUT LOAD vs TEMPERATURE 80 80 VAC 230VAC LOAD (%) 40 LOAD (%) 40 40 25 10 0 15 30 50 70 (HORIZONTAL) 40 0 10 30 50 70 75 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 65 Constant Current Mode 90 1 80 70 0.98 0.96 0.94 LOAD (%) 50 40 PF 0.92 0.9 0.88 0.86 0.84 277V 230V 115V 0.82 90 125 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) Hz Derating is needed under low input voltage. 50% % 70% 80% 90% % (240W) LOAD TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 65 EFFICIENCY vs LOAD possess superior working efficiency that up to 93% can be reached in field applications. 48V Model, Tcase at 65 25% 94.5 THD % 15% 10% 5% 277VAC 230VAC 115VAC EFFICIENCY(%) 89.5 84.5 79.5 277V 230V 115V 0% 50% % 70% 80% 90% % 74.5 10% % 30% 40% 50% % 70% 80% 90% % LOAD LOAD
LIFE TIME 1 LIFETIME(Kh) 80 40 0 25 30 35 40 45 50 55 65 70 75 Tc a s e ( )
MECHANICAL SPECIFICATION Case No.213 Unit:mm BlankType 69 52.5 ψ191.5 12.5 300± 300± M12*P1.7518h AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG*3C SJTW 14AWG*2C V(Red) V(Black) 30 tc 150 45 4ψ8.0 tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point Ta AType ψ191.5 69 52.5 12.5 M12*P1.7518h 300± 300± AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG*3C SJTW 14AWG*2C V(Red) V(Black) 32.5 25.25 30 tc 150 45 4ψ8.0 Ta tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point BType ψ191.5 69 52.5 12.5 M12*P1.7518h AC/L(Brown) AC/N(Blue) FG (Green/Yellow) 300± SJTW 18AWG*3C 300± SJTW 14AWG*2C V(Red) V(Black) 30 DIM(BLUE) DIM(WHITE) 300± SVT 18AWG*2C tc 150 45 4ψ8.0 Ta tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point
INSTALLATIONS Hanger Chain High Bay Light Caution Please inspect the appearance of the driver if the package is damaged. There should not be any cracks. Please do not drop or bump the driver. All screws including the suspension screw should be paired with a spring washer and locked tight. The entire luminaire, including the driver, should be limited to 15Kg or less. The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation. Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.