Product size: Coffee Table: L45*W45*H40 cm Rocker: W65*D94*H79.5 cm The frame of this product is manufactured from mild steel coated with a weather resistant paint. Steel has a natural tendency to rust over time and, whilst we expect you to be able to enjoy your furniture for many years to come, we recommend that you check the product from time to time for signs of paint damage and/ or rust. If the paint should become damaged, or if rust begins to form, you should clean the affected area and apply a suitable thinners based touch-up paint. Such paints are readily available from all good hardware and DIY stores. This product is for Domestic Use only IMPORTANT, RETAIN FOR FUTURE REFERENCE READ CAREFULLY A. Mir & Co., Ltd. 1 / 8
Warnings Before you start Don ts IMPORTANT, RETAIN FOR FUTURE REFERENCE READ CAREFULLY See enclosed instructions for assembly, safety and care information. Failure to follow the warnings could result in serious injury. Handle heavy parts with care. Ensure that this product is fully assembled as illustrated before use. This product should only be used on firm, level ground. Keep small parts out of reach of children. Do not stand or climb onto this product. This product is intended for domestic use only. Furniture can be dangerous if incorrectly used. No liability will be accepted for damage or injury caused by incorrect use of this product. Dos When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for assembly. Remove all packaging and banding and place the components carefully on suitable surfaces to prevent damaging or scratching them. Do not use scourers, abrasives, washing powders, chemical cleaners or any other substances containing abrasives since these substances can damage the product, including the glass panel. Never tilt the chair during use. Do not place very hot or very cold items on the glass surface unless adequately thick table-mats are used to prevent such items from coming into contact with the glass. Do not use the glass as a chopping surface. Do not strike glass with hard or pointed items. Do not strike the glass with hard or pointed items. Do not use power tools to construct this product. Do not use this product if parts are missing, damaged or worn. Do not sit or lean on the table. Do not stand or climb onto the product and do not use it as a ladder, as this could lead to it unbalancing and overturning. Never drag furniture when moving it, always lift it. Number of people required for assembly Two people. Time to assemble Check the pack and make sure you have all of the parts listed. Check all screws and bolts are tightened and inspect regularly. This product is suitable for all year outdoor use, but we recommend that a furniture cover be used to add additional protection to your product when not in use. During severe weather conditions and in the winter months we recommend moving your furniture inside into a cool, dry place. Before storage, ensure that the product is clean and dry. To clean, wipe down with a sponge and warm soapy water and wipe with a clean, dry cloth. Cushions should be cleaned following the care instruction on the label. Tools required 40 minutes Tips: Do NOT fully tighten bolts before all components are connected. Only fully tighten once you are satisfied with the alignment of all components. Do not overtighten bolts. A. Mir & Co., Ltd. 2 / 8
This Set is a combination set of 3 pieces. Please find the combination part. Member Part Combination Part No. Diagram Name Qty MP1 Table 1 PC MP2 Rocker 2 PCS A. Mir & Co., Ltd. 3 / 8
Components, fixtures & fittings (not actual size) Parts List Part No. Diagram Qty Part No. Diagram Qty A 1 PC B 4 PCS Table Top Table Legs C 4 PCS D 2 PCS Rocker Armrest/Leg Rocker Seat/Backrest E Rocker Connecting Bar 4 PCS F 4 PCS G 1 PC F1 1 PC L Shaped Tool Spanner N15 M6*15mm 32 PCS N65 M6*65mm 12 PCS N68 M6*68mm 8 PCS DP D13/6.5mm Washer 56 PCS A. Mir & Co., Ltd. 4 / 8
F4 M6 Nut 4 PCS F10 M6 Bolt Head Cap 52 PCS F6 4 PCS AK 2 PCS M6 Nut Cap Allen Key Step by step assembly instructions Note: All Bolt Head Caps and Nut Caps should not be attached before finally tightening all Bolts with Spanner & Allen Key. Only tighten all bolts when you are satisfied with the alignment of all components. A. Mir & Co., Ltd. 5 / 8
Aruba 3 Piece Bistro Rocker Set MP1 Coffee Table Step One Place the Table Top (A) upside down on a flat, non-abrasive surface to avoid scratching the table surface or rim. Step Two Loosely attach the Table Legs (B) onto the Table Top (A) using Washers (DP) and Bolts (N15). Once you are satisfied with the alignment of all components, carefully tighten all bolts using Allen Key (AK). Do not over-tighten. Cover each bolt with Bolt Head Cap (F10). Turn over the assembled table. Your Coffee Table is now ready for use. A. Mir & Co., Ltd. 6/8
Aruba 3 Piece Bistro Rocker Set MP2 - Armchair Step One Assemble the Rocker Armrest/Legs (C) to the Rocker Connecting Bars (E) using Washers (DP), Bolts (N65), Bolt Head Caps (F10), Nuts (F4) and Nut Caps (F6). Step Two Rear Part: Assemble the Rocker Seat/Backrest (D) to the Rocker Armrest/Legs (C) using Washers (DP), Bolts (N68) and Bolt Head Caps (F10). Front Part: Connect Rocker Seat/Backrest (D) to the Connecting Bar and Rocker Armrest/Legs (C) using Washers (DP), Bolts (N68) and Bolt Head Caps (F10). A. Mir & Co., Ltd. 7/8
Step Three Assemble the Part (F) to the Rocker Seat/Backrest (D) using Washers (DP), Bolts (N15), and Bolt Head Caps (F10). Step Four Use L-Shaped Tool (G) to tighten the Part (F). Your Rocker is now ready for use. PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE A. Mir & Co., Ltd. 8 / 8