799 HAVANA BOOKCASE ASSEMBLY INSTRUCTIONS. IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY. Tools Needed Helpline If you have any problems with this product or require any replacement fittings please contact Customer Services Tel: 0 999 Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty. Should you need to return the unassembled product, please repack in the original packaging. IMPORTANT We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions. Carefully check that you have all parts before beginning assembly. Keep fittings out of children's reach and keep children well away from the construction area. We recommend that the packaging is used to protect the surfaces during assembly. A minimum of persons is required to assemble this product. PRODUCT INFORMATION Made from particleboard,mdf with a wood effect finish. Made in Indonesia. CARE INSTRUCTIONS For general cleaning, periodically dust with a soft cloth. Do not rub or scrub the surface when cleaning. Any spills should be removed immediately with a soft clean damp cloth and dried immediately. Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage. Ensure the mats and coasters used do not have an abrasive surface underneath. Do not put hot dishes directly on the surfaces of the item. Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping. Never drag pieces of furniture across the floor as this will cause damage to the joints. All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary. of
FITTINGS x mm. 7.X mm. x mm. P6x9 mm. Fx9 mm. P6x9 mm. mm. F0x0 mm Ax Bx Cx Dx Ex Fx6 Gx Hx0 GLUE 6x0 mm. 0 mm.. Ix Jx Kx PARTS x x x X X 6X STEP ONE X X X of
. Insert 6 x cambolts (B) into the holes of panel and tighten with a screwdriver. STEP TWO. Insert x camlocks (A) into the holes of panel and ensure that arrow indicator is pointing towards the panel edge before tightening with a screwdriver.. Glue and Insert x wooden dowels (C) into the end of panel. STEP THREE. Insert x camlocks (A) into the holes of panels (x), ensure that arrow indicator is pointing towards the panel edge before tightening with a screwdriver.. Insert x cambolts (B) into the holes of panels (x).. Glue and Insert x wooden dowels (C) into the end of panels (x). STEP FOUR. Insert x camlocks (A) into the holes of panel, ensure that arrow indicator is pointing towards the panel edge before tightening with a screwdriver.. Insert x cambolts (B) into the holes of panel and tighten with a screwdriver.. Glue and Insert x wooden dowels (C) into the end of panel. of
STEP FIVE. Insert x camlocks (A) into the holes of panels (x), ensure that arrow indicator is pointing towards the panel edge before tightening with a screwdriver.. Glue and Insert x wooden dowels (C) into the end of panels (x) and 6. 6 STEP SIX. Insert x camlocks (A) into the holes of panel, ensure that arrow indicator is pointing towards the panel edge before tightening with a screwdriver.. Insert x cambolts (B) into the holes of panel.. Glue and Insert x wooden dowels (C) into the end of panel. STEP SEVEN. Insert x camlocks (A) into the holes of panel, ensure that arrow indicator is pointing towards the panel edge before tightening with a screwdriver.. Insert x cambolts (B) into the holes of panel.. Glue and Insert x wooden dowels (C) into the end of panel. STEP EIGHT. Glue x wooden dowels (C) on panel.. Attach panel to panel 6 by using x screws (H),turn clockwise with a cross-head screwdriver until tight. of
STEP NINE. Glue x wooden dowels (C) into the end of panel.. Attach panel to panel and tighten camlocks with a screwdriver to secure the panel together.. Attach panel to the panel by using x screws (H),turn clockwise with a cross-head screwdriver until tight. STEP TEN. Glue x wooden dowels (C) into the end of panel.. Attach panel to panel and tighten camlocks with a screwdriver to secure the panel together.. Attach panel to panel by using x screws (H),turn clockwise with a cross-head screwdriver until tight. STEP ELEVEN. Glue x wooden dowels (C) on panel.. Attach panel to panel to the assembled unit and tighten camlocks with a screwdriver to secure the panel together.. Attach panel to the to the assembled by using x screws (H),turn clockwise with a cross-head screwdriver until tight. of
STEP TWELVE. Glue x wooden dowels (C) on panel 6.. Attach panel 6 to panel by using x screws (H),turn clockwise with a cross-head screwdriver until tight. 6 STEP THIRTHTEEN. Glue 6x wooden dowels (C) on panels, (x) and.. Attach the fixed shelves assembled unit to panel and tighten camlocks with a screwdriver to secure all panels together..attach panel to the assembled unit and tighten camlocks with a screwdriver to secure all panels together. STEP FOURTEEN. Insert panel into the recessed grooves of panels, and.and ensure the tape is facing forward to back side of the item. 6 of
STEP FIFTEEN. Turn the unit upright. This should be lifted by persons.. Glue 6x wooden dowels (C) on panels, and.. Attach panel to the assembled unit and tighten camlocks with a screwdriver to secure all panels together. STEP SIXTEEN.Secure the backboard by tighten 6 x screws(f) with a screwdriver.. Attach x backboard fasteners (I) to the backboard grooves of unit and secure by using x screws (E),turn clockwise with a cross-head screwdriver until tight. STEP SEVENTEEN. Attach x straps (J) to the predrilled holes of panel, using x washers (G) and x screws (D),turn clockwise with a screwdriver until tight. G 7 of
STEP EIGHTEEN. Fix the other ends of the strap to the wall using appropriate screw, washer and wall plug for your wall type. WARNING: Always ensure the area to be drilled is free from hidden electrical wires, water and gas pipes. NOTE: Wall fixing are not included. Please source suitable fixings for your wall type. If it doubt please consult a qualified trade person. FOIL STICKERS Dia. 0 mm. L x HOW TO USE THE FOIL STICKER. Correct Incorrect Use the foil stickers to cover all visible camlock holes from construction. Ensure when placing the sticker the grain of sticker follows the direction of the grain of the panel. This will give a better visual appearance. Next Retail Ltd, Desford Road, Leicester, LE9 AT of