6480 BARLOW CORNER TV ASSEMBLY INSTRUCTIONS. IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY. Tools Needed Helpline If you have any problems with this product or require any replacement fittings please contact Customer Services Tel: 0844 844 8 Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty. Should you need to return the unassembled product, please repack in the original packaging. IMPORTANT We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions. Carefully check that you have all parts before beginning assembly. Keep fittings out of children's reach and keep children well away from the construction area. We recommend that the packaging is used to protect the surfaces during assembly. A minimum of 2 persons is required to assemble this product. PRODUCT INFORMATION Made from particleboard,mdf with a wood effect finish. Made in Indonesia. CARE INSTRUCTIONS For general cleaning, periodically dust with a soft cloth. Do not rub or scrub the surface when cleaning. Any spills should be removed immediately with a soft clean damp cloth and dried immediately. Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage. Ensure the mats and coasters used do not have an abrasive surface underneath. Do not put hot dishes directly on the surfaces of the item. Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping. Never drag pieces of furniture across the floor as this will cause damage to the joints. All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary. 1 of
FITTINGS 15x12 mm..5x2 mm. 8x2 mm. 25x0 mm. P4x15 mm. F6x1 mm. Ax20 Bx20 Cx1 Dx2 Ex2 Fx8 00 mm. 00 mm. F6x1 mm..5x5 mm. x1 mm. F 8x50 mm. F10X0 mm. GRx2 GLx2 Hx4 Ix4 Jx6 Kx1 Lx1 PARTS 1x1 2x1 x1 x1 x1 5x1 x1 x1 x1 8x1 x2 x2 x2 x2 12x2 2 of
STEP ONE Insert 6x cambolts (B) into the holes of panel 1.Tighten with a screwdriver. Insert 2x camlocks (A) into the holes of panel 2 and ensure that arrow indicator is pointing towards the panel edge before tightening with a screwdriver. Insert 2 x wooden dowels ( C ) into the end on panel 2. Insert 4x cambolts (B) into the holes of panel. 1 2 STEP TWO Recommend to use cross-blade screwdriver. Insert 4 x camlocks (A) into the holes of panel and and ensure that arrow indicator is pointing towards the panel edge. Insert 2 x cambolts (B) and 4 x mini cambolts (J) into the holes of panel and. Insert 4 x wooden dowels (C) into the holes of panel and. Insert 4 x bendy cambolts (I) into the inserted nut holes of panel and.and tighten clockwise by hand until tight. STEP THREE Recommend to use cross-blade screwdriver. Insert 2x camlocks (A) into the holes of panel 5 and ensure that arrow indicator is pointing towards the panel edge. Insert 4x wooden dowels (C) into the holes of panel 5. Insert 6 x camlocks (A) into the holes of panel and. Ensure that arrow indicator is pointing towards the panel edge. Insert 2 x wooden dowel (C) into the end of panel and. Insert 2 x mini cambolts (J) into the hole of panel and. 5 of
STEP FOUR Insert 2x camlocks (A) into the holes of panel and ensure that arrow indicator is pointing towards the panel edge. Insert 1x wooden dowel (C) into the holes of panel. Insert 2x wooden dowels (C) into the holes of panel 8. 8 STEP FIVE Attach panel to the panel 5 and secure by tightening 1x screws (K) clockwise with a cross-blade screwdriver until tight. 5 STEP SIX Adjust the bendy cambolts to go directly into the holes of panel and. Attach panel to panel by tightening 2 x camlocks (A) clockwise with a flat-blade screwdriver. Attach panel to panel by tightening 2 x camlocks (A) clockwise with a flat-blade screwdriver. TOP VIEW 4 of
STEP SEVEN Attach the assembled unit ( - ) and ( - ) to the panel 2 by tightening 2 x camlocks (A) clockwise with a flat-blade screwdriver. STEP EIGHT Attach the assembled unit (panel 5 and ) to assembled unit by tightening 1x screw (L) clockwise with a crossblade screwdriver. 5 2 STEP NINE Carefully attach panel into the assembled unit. This should be lifted and positioned by 2 people. Secure panel to the assembled unit by tightening 6 x housing screws (on the bottom side of panel ) clockwise with a cross-blade screwdriver. A Tighten 4 x camlocks (A) clockwise with a flatblade screw screwdriver. 5 A 2 5 5 of
STEP TEN Carefully lift the unit upright. This should be lifted by 2 persons. Attach panel 1 to the assembled unit by tightening 6x camlocks (A) clockwise with cross-blade screwdriver. 1 STEP ELEVEN Attach panel 8 to assembled unit by tightening 4x screws (H) clockwise with a cross-blade screwdriver. 1 8 Finished side STEP TWELVE Insert 4 x cambolts (B) into the holes of panel (x2). Attach 2 x handle (D) to the holes of panel (x2) and secure by tightening 2 x screw (H) clockwise with a screwdriver. Insert 2x camlock (A) into the hole of panel (x2). Turn over panel and insert 2 x cambolt (B), 4 x wooden dowels ( C ). 6 of
STEP THIRTEEN Insert 2 x camlock (A) into the hole of panel (x2). Turn over panel and insert 2 x cambolt (B), 4 x wooden dowels ( C ). Insert 4 x camlocks (A) and 8 x wooden dowels (C) into the holes of panel (x2). STEP FOURTEEN Attach panel and to panel and tightening camlocks (A) clockwise with a cross-blade screwdriver Repeat this step for the remaining parts. STEP FIVETEEN Insert panel 12 to the recessed grooves of panel, and. Repeat this step for the remaining parts. 12 of
STEP SIXTEEN Attach panel to the assembled unit by tightening 2x camlocks (A) clockwise with a flat-blade screwdriver. Repeat this step for the remaining parts. 12 STEP SEVENTEEN Attach 1x male runner (GR) to the assembled unit by tightening 2x screws (F) clockwise with a screwdriver. Attach 1x male runner (GL) to the assembled unit by tightening 2x screws (F) clockwise with a screwdriver. Repeat this step for the remaining a assembled drawer. STEP EIGHTEEN Insert the drawer unit to the assembled unit. And now, this cabinet is ready for use. 1 Next Retail Ltd, Desford Road, Leicester, LE1 4AT 8 of
6480 BARLOW CORNER TV (FOIL STICKER) The foil sticker is used for covering the camlock or predrilled holes of products. They will help making the grain and colour is even and consistency. FITTINGS Dia. 20 mm. M x 20 HOW TO USE THE FOIL STICKER. Correct Wrong Note : Whilst position foil stickers to cover the holes. Ensure that you arrange them on the centre of the holes before sticking. And ensure the grain direction of foil sticker have to be in the same direction as current surface area. Next Retail Ltd, Desford Road, Leicester, LE1 4AT of