CERTIFICATE OF APPROVAL No CF 5610 1 This is to certify that, in accordance with TS00 General Requirements for Certification of Protection Products The undermentioned products of Parkhouse Road, Carlisle, Cumbria CA3 0JU Tel: 01228 511770 Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT EUROSPEC Residential Range of Mortice Locks and Latches TECHNICAL SCHEDULE TS23 The Contribution of Locks and Latches to the Performance of Resisting sets Signed and sealed for and on behalf of Exova (UK) Limited trading as Warrington Certification Paul Duggan Certification Manager Next audit test due: 10/01/2019 Frequency: Annually Valid to: 8 th January 2023 Page 1 of 11
1. The locks and latches covered by this certificate are all steel cased. The approval applies to the following products: Reference ESE5025 ESE5030 EDE5025 EDE5030 LSE5230 LSE5225 LSE5325 LSE5330 LDE5325 LDE5330 BAE5025 BAE5030 ULE5025 ULE5030 Description Euro profile sashlock Euro profile sashlock Euro profile deadlock Euro profile deadlock 2 lever sashlock 2 lever sashlock 3 lever sashlock 3 lever sashlock 3 lever deadlock 3 lever deadlock Bathroom lock Bathroom lock Upright latch Upright latch All locks have a maximum 22 mm wide forend and a maximum 25 mm wide strikeplate (excluding the latchbolt lip), and are available with either a Euro profile cylinder or lever options. The latchbolt and deadbolt are brass, and the case, forend and strikeplates are all of steel, with a minimum latchbolt/deadbolt projection of 12 mm. The forends and strikeplates incorporate either square or radiused corners. The full list of the lock/latch variants is identified in Annex A. 2. This approval relates to their use with the following assemblies:- Latched and unlatched, intumescent sealed assemblies consisting of timber faced and edged leaves with timber, cellulosic or mineral cores in timber frames having a fire of up to 60 minutes (Code ITT). 3. This certificate is designed specifically to demonstrate compliance of the product or system with Approved Document B (England and Wales); the Technical Handbooks (Scotland); Technical Booklet E (N. Ireland). If compliance is required with other regulatory or guidance documents there may be additional considerations or conflicts to be taken into account. Page 2 of 11 Signed
4. This approval relates to the use of the above locks/latches in contributing to the fire performance of timber based sets and metallic based sets, as defined in BS EN 1634-1 or BS 476: Part 22: 1987. 5. The locks are approved on the basis of: i) Initial type testing to EN 1634-1 and EN 12209 ii) An appraisal against TS23 iii) Certification of quality management system to ISO 9001. iv) Inspection and surveillance of factory production control v) On-going audit testing in accordance with TS23 requirements 6. The mortice locks and/or latches should only be used with assemblies of proven fire (as defined in BS EN 1634-1 or BS 476: Part 22: 1987), the critical aspects of the set construction are considered to be the material of the frame, the leaf to frame clearance gaps and the lipping material. Attention should be paid to these details and these should not be amended from that previously fire tested. The following minimum specification shall be followed: Timber-based assemblies (Code ITT30 and ITT60): i) frame density - 450 kg/m³ (30 minutes), 640 kg/m 3 (60 minutes) ii) leaves shall have a minimum thickness of 44 mm for 30 minute s and 54 mm for 60 minute s. iii) Lipping density - 640 kg/m 3. 7. When fitted to insulated ITT 30 or ITT60 timber or mineral composite assemblies, The required protection will be as follows: i) The required protection for 30 minute ITT s will be 0.8 mm thickness of graphite-based sheet material, around the lock case and behind the forend and strike plate. ii) The required protection for 60 minute ITT s will be 0.8 mm thickness of graphite-based sheet material around the lock case and behind the forend and strike plate. Additionally the perimeter intumescent fire seal within the frame/ edge shall by-pass the strike plate or forend by a minimum of 7 mm wide on each side (with the exception of the latchbolt lip where present). Note: Failure to install the intumescent protection will invalidate this certificate Page 3 of 11 Signed
8. The mortice locks and/or latches and their associated strikeplates and keeps may only be fitted in the manner described in this certificate and subject to any limitations on the inclusion of locks/latches specified for the leaf. This approval is applicable only to the specified locks used with assemblies of proven fire (as defined in BS EN 1634-1) and when using appropriate intumescent protection. 9. Lock assemblies not incorporating a latching mechanism shall only be fitted to proven unlatched assemblies. 10. The locks/latches should not be fitted higher than 1100 mm from the to the finished floor level of the surrounding floors. 11. Timber sets shall be installed in accordance with BS 8214. 12. The approval relates to on-going production. Product and/or its immediate packaging is identified with the manufacturer s name, the product name or number, the CERTIFIRE name or name and mark, together with the CERTIFIRE certificate number and where appropriate. Page 4 of 11 Signed
13. The following table shows the acceptable set types and fire periods: : - approved - Not approved Approved Type Class IMM MM ITT ITM ITC FD20 FD30 FD60 FD90 FD120 FD240 E 20 EI 20 E 30 EI 30 E 60 EI 60 E 90 EI 90 E 120 EI 120 E 240 EI 240 Page 5 of 11 Signed
14. s are classified as the following types: Type MM - 20 minute to 240 minute sets that consist of metallic leaves in metallic frames that do not contain intumescent materials in the frame to leaf gap. Type IMM - 20 minute to 240 minute sets that consist of metallic leaves in metallic frames that contain intumescent materials in the frame to leaf gap. Type ITT - 20 minute to 120 minute sets containing intumescent seals and consisting of non-metallic faced and edged leaves hung in timber frames Type ITM - 20 minute to 120 minute sets containing intumescent seals and consisting of non-metallic faced and edged leaves hung in metal frames. Type ITC - 20 minute to 120 minute sets containing intumescent seals and consisting of non-metallic faced and edged leaves hung in proprietary composite frames, of which the principal material is other than timber or metal but which may include any other materials. Scope of Approval The maximum dimension of strikeplate approved is as follows: Width (excl. latchbolt lip) Height Thickness Latchbolt lip height 24 mm 125 mm 85 mm Plastic dust boxes may be incorporated behind the strikeplates of for both 30 minute and 60 minute s. Page 6 of 11 Signed
Classification codes: ESE5025 & ESE5030 Sashlocks: & 2 H 8 1 0 F 1 B A 2 0 EDE5030 & EDE5025 Deadlocks: & 2 H 8 1 0 F 1 B A 0 0 LSE5325 LSE 5225, LSE 5230 & LSE5330 Sashlocks: & 2 H 8 1 0 F 1 K D 2 A ULE5030 & ULE 5025 Upright latches: & 2 H 8 1 0 F - B 0 2 0 BAE 5025 & BAE 5030 & 2 H 8 1 0 F - B G 2 0 LDE 5325 & LDE 5330 & 2 H 8 1 0 F 1 K D 0 A Page 7 of 11 Signed
Further Information Further information regarding the details contained in this certificate may be obtained from Carlisle Brass Ltd (Tel: 01228 511770). Further information regarding CERTIFIRE certification and other approved products can be obtained from CERTIFIRE (Tel: 01925 646777). Page 8 of 11 Signed
CODE BAE5025EB BAE5025EB/R BAE5025NP BAE5025NP/R BAE5025SN BAE5025SN/R BAE5025BK/B BAE5025FB/B BAE5030BK/B BAE5030FB/B BAE5030EB BAE5030EB/R BAE5030NP BAE5030NP/R BAE5030SN BAE5030SN/R DESCRIPTION Annex A FACE PLATE LATCH/ BOLT RESIDENTIAL - RADIUS brass brass RESIDENTIAL - RADIUS (POLISHED) Polished Nickel Nickel RESIDENTIAL - RADIUS (SATIN) Satin Nickel Nickel EASI-T BATHROOM LOCK (RESIDENTIAL) 64mm - BLH black brass EASI-T BATHROOM LOCK (RESIDENTIAL) 64mm - BLH bronze brass EASI-T BATHROOM LOCK (RESIDENTIAL) 76mm - BLH black brass EASI-T BATHROOM LOCK (RESIDENTIAL) 76mm - BLH bronze brass RESIDENTIAL - RADIUS brass brass RESIDENTIAL - RADIUS (POLISHED) Polished Nickel Nickel RESIDENTIAL - RADIUS (SATIN) Satin Nickel Nickel EDE5025EB EDE5025NP EDE5025SN EDE5030EB EDE5030NP EDE5030SN 64mm 64mm 64mm 76mm 76mm 76mm Page 9 of 11 Signed
Annex A - Continued CODE ESE5025EB ESE5025NP ESE5025SN ESE5030EB ESE5030NP ESE5030SN LDE5325EB LDE5325NP LDE5325SN LDE5330EB LDE5330NP LDE5330SN LSE5225BK/B LSE5225EB/B LSE5225FB/B LSE5225NP/B LSE5225SN/RB LSE5225NP/RB LSE5325EB LSE5325EB/R LSE5325NP LSE5325NP/R LSE5325SN DESCRIPTION FACE PLATE LATCH/ BOLT CASE 64mm CASE 64mm CASE 64mm CASE 76mm CASE 76mm CASE 76mm EASI-T 3 LEVER DEADLOCK 64mm EASI-T 3 LEVER DEADLOCK 64mm EASI-T 3 LEVER DEADLOCK 64mm EASI-T 3 LEVER DEADLOCK 76mm EASI-T 3 LEVER DEADLOCK 76mm EASI-T 3 LEVER DEADLOCK 76mm 64mm - BLH black brass 64mm - BLH brass brass 64mm - BLH bronze brass 64mm - BLH Polished Nickel Nickel RADIUS 64mm - BLH Polished Nickel Nickel RADIUS 64mm - BLH Satin Nickel Nickel RESIDENTIAL - RADIUS brass brass RESIDENTIAL - RADIUS (POLISHED) Polished Nickel Nickel Page 10 of 11 Signed
Annex A - Continued CODE LSE5325SN/R LSE5230EB/B LSE5230FB/B LSE5230NP/B LSE5330EB LSE5330EB/R LSE5330NP LSE5330NP/R LSE5330SN LSE5330SN/R ULE5025NP ULE5025NP/R ULE5030NP ULE5030NP/R ULE5025SN ULE5025SN/R ULE5030SN ULE5030SN/R DESCRIPTION FACE PLATE LATCH/ BOLT RESIDENTIAL - RADIUS (SATIN) Satin Nickel Nickel 76mm - BLH brass brass 76mm - BLH bronze brass 76mm - BLH Polished Nickel Nickel RESIDENTIAL - RADIUS brass brass RESIDENTIAL - RADIUS (POLISHED) Polished Nickel Nickel RESIDENTIAL - RADIUS (SATIN) Satin Nickel Nickel EASI-T UPRIGHT LATCH 64mm RESIDENTIAL (POLISHED) Polished Nickel Nickel EASI-T UPRIGHT LATCH 64mm RESIDENTIAL - RADIUS (POLISHED) Polished Nickel Nickel EASI-T UPRIGHT LATCH 76mm RESIDENTIAL (POLISHED) Polished Nickel Nickel EASI-T UPRIGHT LATCH 76mm RESIDENTIAL - RADIUS (POLISHED) Polished Nickel Nickel EASI-T UPRIGHT LATCH 64mm RESIDENTIAL (SATIN) Satin Nickel Nickel EASI-T UPRIGHT LATCH 64mm RESIDENTIAL - RADIUS (SATIN) Satin Nickel Nickel EASI-T UPRIGHT LATCH 76mm RESIDENTIAL (SATIN) Satin Nickel Nickel EASI-T UPRIGHT LATCH 76mm RESIDENTIAL - RADIUS (SATIN) Satin Nickel Nickel Page 11 of 11 Signed