MODEL VIEWS MY NOT REPRESENT EXCT MODEL PURCHSED B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 1 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:08 M, DWG To PDF.pc3
TOOLS REQUIRED 1 2 " WRENCH 1 2 " SOCKET ND TORQUE WRENCH - OPTIONL 4MM LLEN WRENCH SSEMBLY COMPONE ITEMS INCLUDED PRT # PRT QTY TOP ND ON SSEMBLY N/ TOP SSEMBLY (FCTORY SSEMBLED) 1 CBINET N/ CBINET - SIZE VRIES 1 LEGS VRIES LEG,MPL - HEIGHT VRIES 2 LEG HRDWRE 520001 LEG HRDWRE KIT, 1 LEG 2 LEG BRCE N/ LEG BRCE - SIZE VRIES 1 STRETCHER N/ STRETCHER - 20.75" LONG 1 CONFIRMTS - LEGS 227578 CONFIRMTS - STRETCHER 228564 SCREW,7MMX90MM,CONN,LLENHED, BLCK SCREW,7MMX50MM,CONN,LLENHED, BLCK BOLT - INTERNL ON 231922 BOLT, 3 8-16 X 625 HEX HED 2 WSHER - INTERNL ON 100451 WSHER, 5 16 FLT ZINC PLTED 2 PENCIL LEDGE 14-0027 PENCIL LEDGE 1 SCREWS - PENCIL LEDGE 236263 SCREW,#6X 3 4 TRUSS HED,QUD BLCK 6 4 4 B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES TOOLS ND SSEMBLY COMPONE 2 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:13 M, DWG To PDF.pc3
ON SIDE FCING UP STEP 1: LY ON SSEMBLY ON FLOOR WITH ON SIDE FCING UP. **NOTE** BE SURE TOP SSEMBLY IS ON CLEN SURFCE SUCH S PCKGING FOM, CRDBORD, OR BLNKET TO PREVENT DMGE B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 3 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:18 M, DWG To PDF.pc3
STEP 2: INSERT HNGER BOLT ON ONE LEG THROUGH THE CORNER BRCKET ND INSERT LOCK WSHER ND HEX NUT. SCREW ON NUT USING 1 2" WRENCH OR 1 2" SOCKET ND TORQUE WRENCH. DO NOT TIGHTEN LL THE WY. REPET FOR THE OTHER LEG. THE LEG WITH CHMFER MUST GO ON THE FRONT OF THE TBLE WITH CHMFERED EDGE FCING OUT. INSERT HNGER BOLT THROUGH HERE WITH LOCK WSHER ND HEX NUT FRONT LEG BCK LEG FRONT ON HINGE LEG WITH CHMFER NEEDS TO BE FCING OUT CLOSE UP OF CORNER LEG SSEMBLY CLOSE UP OF LEG WITH CHMFER B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 4 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:23 M, DWG To PDF.pc3
LEG LEVELER STEP 3: SCREW LEG LEVELERS INTO T-NUT ON BOTTOM OF LEGS. CLOSE UP OF LEG LEVELER SSEMBLY B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 5 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:28 M, DWG To PDF.pc3
LEG BRCE STEP 4: TTCH BRCE TO LEGS INSERT CONFIRMTS INTO ONE LEG ND SCREW INTO BRCE. REPET FOR THE OTHER LEG. MKE SURE BRCE IS STRIGHT ND LL CONFIRMTS RE SECURE. B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 6 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:33 M, DWG To PDF.pc3
STRETCHER STEP 5: TTCH STRETCHER TO BRCE WITH HRDWRE PROVIDED. GO BCK TO STEP 2 ND TIGHTEN UP THE HNGER BOLTS FOR ECH LEG USING 1 2" WRENCH OR 1 2" SOCKET ND TORQUE WRENCH, TO MINIMUM OF 12FT LBS BUT NOT TO EXCEED 17FT LBS. B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 7 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:38 M, DWG To PDF.pc3
STEP 6: LEFT SIDE FLIP ON SSEMBLY OVER ONTO LEGS. LIGN HOLES ON STRETCHER TO HOLES ON LEFT SIDE OF CBINET. TKE OUT DRWERS TO TTCH STRETCHER FROM INSIDE THE CBINET. TTCH TO CBINET WITH HRDWRE PROVIDED. CONFIRMTS STRETCHER OUTSIDE OF CBINET INSIDE OF CBINET DRWERS ND HRDWRE REMOVED FOR CLRITY B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 8 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:43 M, DWG To PDF.pc3
BRCKET - TYPICL TTCH ON SSEMBLY TO CBINET THROUGH HERE ON BOTH BRCKETS BCK ON INTERNL ON STEP 7: FRONT ON POSITION ON SSEMBLY SO INNER HOLES OF BRCKETS ON INTERNL ON RE LINED UP WITH TWO HOLES ON LEFT SIDE OF CBINET. FRONT ON WILL BE FLUSH WITH FRONT OF CBINET ND BCK ON WILL BE FLUSH WITH BCK OF THE CBINET. TTCH ON SSEMBLY TO LEFT SIDE OF CBINET WITH HRDWRE PROVIDED. DJUST LEG LEVELERS TO LEVEL ON SSEMBLY WITH CBINET. CLOSE UP OF ON SSEMBLY SHOWN (TOP REMOVED FOR CLRITY) B UPD STEP 1 12/29/14 EMK NME - ECN NO. : : : DIMENSION RE IN INCHES 9 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:48 M, DWG To PDF.pc3
PENCIL LEDGE STEP 8: LINE UP PENCIL LEDGE ON SIDE OF DJUSTBLE TOP IN DESIRED LOCTION. PRE-DRILL HOLES IN TOP TO PREVENT SPLITTING. SCREW PENCIL LEDGE TO TOP USING HRDWRE PROVIDED. SET YOUR TBLE IN PLCE. PUT DRWERS BCK IN. COMPLETE UNIT SHOWN B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 10 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:53 M, DWG To PDF.pc3