TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System

Submittal Bulletin TE-7700 Series Issue Date July 10, 2003 TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System The TE-7700 Series RF Wireless Room Temperature Sensing System consists of a TE-7710 Series RF Wireless Temperature and Set Point, and a TE-7720 or TE-7730 Series RF Receiver. Together, these components monitor the temperature set point and zone temperature, and transmit this data to the receiver at predefined intervals. The information is translated into a control signal that works directly with a wide variety of Johnson Controls and compatible competitors digital controllers in Heating, Ventilating, and Air Conditioning (HVAC) systems. The TE-7700 Series RF Wireless Room Temperature Sensing System uses 900 MHz spread-spectrum technology to prevent accidental and unauthorized interference, and to provide better propagation characteristics within the building. Field-addressable DIP switches establish a unique, secure address between each transmitter and receiver. The TE-7700 system provides indication of RF signal strength and low battery. Indication of zone bus communication is also provided on the TE-7720 Series RF Receiver. To optimize comfort in larger zones, a single receiver can average the measured temperature of up to four transmitters in the zone, or select the highest or lowest measured temperature of the zone. Optional signal strength site survey tools are available to determine the appropriate location of the RF wireless temperature sensing system, prior to its installation. These fast-update, 5-second interval tools verify that the RF signal strength is sufficient to ensure proper operation. Figure 1: TE-7700 Series RF Wireless Room Temperature Sensing System Note: The TE-7700 Series RF Wireless Room Temperature Sensing System consists of a TE-7710 Series RF Wireless Temperature and Set Point, and a TE-7720 Series RF Receiver (for zone bus interface with Johnson Controls VMA1400 Series Digital Controllers) or a TE-7730 Series RF Receiver (for analog interface with Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, and compatible competitors digital controllers). Features and Benefits RF Wireless Design Improved Application Flexibility Allows for quick, economical, and low-maintenance installation, reducing total installed cost Provides an alternative to hardwired room temperature sensing counterparts, especially in installations where building aesthetics (such as solid walls or ceilings, temporary walls, or decorative surfaces) would normally hinder hardwiring Continued on next page... 2003 Johnson Controls, Inc. 1 Code No. LIT-1201504 www.johnsoncontrols.com

Features and Benefits (Cont.) 900 MHz Spread-Spectrum Technology Works with Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, VMA1400, and Compatible Competitors Digital Controllers Field-Addressable DIP Switches Multiple Temperature Averaging and High/Low Selection Three-Level RF Signal Strength Light-Emitting Diode (LED) Integral to the Receiver Zone Bus Activity LED (TE-7720-0 Only) Low Battery Indication (Via Zone Bus for TE-7720-0; Via Low Battery Relay and LED for TE-7730-0) Manual Occupancy Override Pushbutton One-to-One Control Approach Nominal 60-Second Transmission Intervals Universal Mounting Optional Signal Strength Site Survey Tools Available to Determine the Appropriate Temperature Sensing System Location Prior to Installation Prevents accidental and unauthorized interference, and provides better propagation characteristics within the building Establishes a new platform for room temperature sensing communications Establish a unique, secure address between each transmitter and receiver Optimizes comfort in larger zones since a single receiver can average the measured temperature of up to four transmitters in the zone, or select the highest or lowest measured temperature of the zone Provides visual indication of adequate RF signal strength in nominal 60-second intervals, and minimizes the need for pre-installation signal strength measurements using a site survey tool Provides direct, visual indication of communication between the receiver and the VMA1400 Series Digital Controller Provides battery condition to warn supervisory equipment in advance when the battery needs to be replaced Signals the receiver that the zone is occupied, to override time-of-day scheduling Enhances reliability by reducing susceptibility to signal interference and by preventing a single point of failure in multiple zone applications Provide optimal HVAC control, while conserving battery life Provides added flexibility since the temperature transmitter may be easily relocated after initial installation Fast-update, 5-second transmission intervals provide quick assurance of a strong RF transmission signal for proper operation 2 TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin

RF Wireless s RF Receivers T E 7 7 1 0 T E 7 7 0 0 Set Point Adjustment and Scale Type 0 = None 1 = Temperature, Warmer/Cooler 2 = Temperature, Scaled (55 to 85 F/13 to 29 C) Indication Type N = None B = Liquid Bulb Thermometer Digital Controller Interface 2 = Zone Bus Interface with Johnson Controls VMA1400 Series Digital Controllers 3 = Analog Interface with Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, and Compatible Competitors Digital Controllers Table 1: and Receiver Models Available Figure 2: Features and Options Ordering Matrices for RF Wireless s and RF Receivers Code Number Description TE-7710-0N* TE-7710-1N* TE-7710-1B* TE-7710-2N* TE-7710-2B* TE-7720-0** TE-7730-0** RF Wireless, No Set Point Adjustment, No Liquid Bulb Thermometer Indication RF Wireless, Warmer/Cooler Set Point Adjustment, No Liquid Bulb Thermometer Indication RF Wireless, Warmer/Cooler Set Point Adjustment, with Liquid Bulb Thermometer Indication RF Wireless, Temperature Set Point Adjustment Scaled 55 to 85 F (13 to 29 C), No Liquid Bulb Thermometer Indication RF Wireless, Temperature Set Point Adjustment Scaled 55 to 85 F (13 to 29 C), with Liquid Bulb Thermometer Indication RF Receiver for TE-7710 Series s, Includes 6 ft (1.8 m) Cable to Connect Power and Zone Bus Interface Between Receiver and Johnson Controls VMA1400 Series Digital Controllers RF Receiver for TE-7710 Series s, Includes 6 ft (1.8 m) Cable to Connect Power and Analog Interface Between Receiver and Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, and Compatible Competitors Digital Controllers * Includes one 3.0-volt lithium battery. ** Configured and commissioned using either HVAC PRO software (Release 8.04B or later; AS-AHU, AS-UNT, AS-VAV, and VMA1400 Series Digital Controllers only), or GX-9100 Programming Tool (Release 7.02 or later; DX-9100 Series Digital Controllers only) and GX-9100 Commissioning Tool (Release 8.04 or later; DX-9100 Series Digital Controllers only). TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin 3

Table 2: Accessories and Replacement Parts Available Code Number Duracell Ultra 123, Panasonic CR123A, Toshiba CR123A, GE/Sanyo CR123A, or Equivalent TE-7710-100 TE-7720-100 TE-77DO-601 TE-77DO-602 CBL-STAT25 CBL-STAT50 CBL-STAT75 CBL-STAT100 GRD10A-608 T-4000-119 Description Replacement Battery (Purchase Locally), 3.0-Volt Lithium Battery (One Required for, One Required for Signal Strength Site Survey Tool, and Three Required for Receiver Signal Strength Site Survey Tool) RF Wireless Signal Strength Site Survey Tool (For Use with TE-7720-100 RF Wireless Receiver Signal Strength Site Survey Tool) RF Wireless Receiver Signal Strength Site Survey Tool (For Use with TE-7710-100 RF Wireless Signal Strength Site Survey Tool) RF Wireless Door Replacement Kit with Johnson Controls Logo (10 per Kit) RF Wireless Door Replacement Kit without Johnson Controls Logo (10 per Kit) 25 ft (7.6 m) Interface Cable to Connect Zone Bus Between TE-7720 Series RF Receiver and Johnson Controls VMA1400 Series Digital Controllers (Does Not Include Power Cable) 50 ft (15.2 m) Interface Cable to Connect Zone Bus Between TE-7720 Series RF Receiver and Johnson Controls VMA1400 Series Digital Controllers (Does Not Include Power Cable) 75 ft (22.9 m) Interface Cable to Connect Zone Bus Between TE-7720 Series RF Receiver and Johnson Controls VMA1400 Series Digital Controllers (Does Not Include Power Cable) 100 ft (30.5 m) Interface Cable to Connect Zone Bus Between TE-7720 Series RF Receiver and Johnson Controls VMA1400 Series Digital Controllers (Does Not Include Power Cable) Plastic Guard with Baseplate and Mounting Ring Allen-Head Adjustment Tool (30 per Bag) 4 TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin

Side View (Wallbox Mounted) 9/32 (7) Front View (Wallbox Mounted) Height (Surface Mounted) 3-3/16 (81) 4-3/4 (121) Height (Wallbox Mounted) 1-13/32 (36) 3-3/16 (81) Side View (Surface Mounted) Note: The wallbox-mounted arrangement assumes that a standard 2 x 4 in. (51 x 102 mm) wallbox is used. 1-13/32 (36) Figure 3: TE-7710 Series RF Wireless Temperature and Set Point s Dimensions, in. (mm) 4-13/16 (122) 2-1/16 (52) 5-3/4 (146) Figure 4: TE-7720 and TE-7730 Series RF Receivers Dimensions, in. (mm) TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin 5

System Operation The TE-7700 Series RF Wireless Room Temperature Sensing System is designed to work directly with Johnson Controls and compatible competitors digital controllers in HVAC systems, to monitor the temperature set point and zone temperature. This RF system consists of a wireless TE-7710 Series Temperature and Set Point, and a TE-7720 or TE-7730 Series Receiver. Figures 5 and 6 illustrate the relationship between the TE-7710 Series, the TE-7720 or TE-7730 Series Receiver, and the digital controller. The TE-7710 Series RF Wireless and the TE-7720-0 RF Receiver with zone bus interface function with Johnson Controls VMA1400 Series Digital Controllers. The RF receiver outputs zone temperature, temperature set point, field strength measurements, and low battery indication via the zone bus. The TE-7710 Series RF Wireless and the TE-7730-0 RF Receiver with analog interface function with Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, and compatible competitors digital controllers. Compatible models should have analog inputs that are scalable to accept a 0 to 5 VDC signal for zone temperature and temperature set point (if required), and binary inputs for low battery indication and occupancy status (if required). Note: Due to the 900 MHz operating frequency of the TE-7700 Series RF Wireless Room Temperature Sensing System, this product is generally not acceptable for use outside of the United States, Canada, Mexico, Australia, New Zealand, or South America. The battery-operated transmitter of the TE-7700 Series RF Wireless Room Temperature Sensing System communicates the temperature set point and zone temperature approximately every 60 seconds. These 60-second transmission intervals provide optimal HVAC control, while conserving battery life. The transmitted information is combined with a unique, secure DIP switch selectable address and other supporting data prior to transmission. To optimize comfort in larger zones, a single receiver can average the measured temperature of up to four transmitters in the zone, or select the highest or lowest measured temperature of the zone. In multiple transmitter applications requiring set point adjustment, only one of the transmitters needs to include set point adjustment capability. A receiver with the same address as the transmitter receives the transmitted information and converts the data into the appropriate units and electrical format to be understood by the digital controller. This information also indicates the transmitter battery condition, to warn supervisory equipment in advance when the battery needs to be replaced. The zone bus link of the TE-7720-0 RF Receiver also includes diagnostic data, such as field strength measurements and transmission number, to help with commissioning and site evaluation. A three-level RF signal strength LED minimizes the need for pre-installation signal strength measurements using a site survey tool. A continuous illumination of the three-level RF signal strength LED indicates that the receiver has power and is ready for operation. Transmission intervals occur approximately every 60 seconds, with three-level LED indication occurring immediately after every transmission. A second zone bus LED on the TE-7720-0 RF Receiver provides direct, visual indication of communication between the receiver and the Johnson Controls VMA1400 Series Digital Controller. A second low battery LED on the TE-7730-0 RF Receiver provides convenient, advance indication of a low battery condition on the transmitter. A continuous illumination of the low battery LED indicates that the transmitter battery needs to be replaced. A manual occupancy override pushbutton on the TE-7710 Series allows the occupant to control the temperature of a zone by overriding time-of-day scheduling. This feature allows the end user to signal the receiver that the space is occupied after normal business hours or on weekends. Optional signal strength site survey tools are available to determine the appropriate location of the TE-7700 Series RF Wireless Room Temperature Sensing System prior to its installation. These fast-update, 5-second interval site survey tools verify that the RF transmission signal is sufficient to ensure proper system operation. Refer to the TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Product Bulletin (LIT-1201503) for additional product information. 6 TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin

Recommended Applications Using the mounting hardware included with each component, the TE-7700 Series RF Wireless Temperature Sensing System is ideal for installations where building aesthetics would normally hinder hardwiring. Recommended applications for this RF wireless system are numerous and include the following: museums, historical buildings, atriums, or other sites where building retention and its historical preservation are important office buildings, university campuses, educational facilities, correctional facilities, and other structures that incorporate brick or solid concrete walls and/or ceilings buildings featuring marble, granite, glass, mirrored, wood veneer, or other decorative surfaces that present significant challenges when attempting hardwiring office buildings, retail stores, and other commercial real estate where tenant turnover is frequent and temporary walls and ceilings are common stadiums, arenas, gymnasiums, convention centers, airports, zoos, and other locations that feature large, open spaces buildings containing asbestos walls or other biohazards that cannot be disturbed TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin 7

Tstat Wiring To Supply Transformer 24 VAC 24 VAC COM TE-7720 Series RF Receiver with Zone Bus Interface Johnson Controls VMA1400 Series Digital Controller TE-7720-0 RECEIVER RF SIGNAL ZONE BUS 24 VAC 24 VAC COM ZONE BUS to VMA1400 (Tstat) RF ADDRESS MULT XMTRS 24VAC: 1 24VAC: 2 Power and Zone Bus Interface with Johnson Controls VMA1400 Series Digital Controller (6 ft Interface Cable Included with TE-7720 Series RF Receiver) RF Transmission Signal from to Receiver TE-7710 Series RF Wireless Temperature and Set Point Liquid Bulb Thermometer Set Point Adjustment Slider Mounting Base WIRELESS Manual Occupancy Override Pushbutton Pull Tab Access Door Figure 5: TE-7710 Series RF Wireless Temperature and Set Point, TE-7720 Series RF Receiver with Zone Bus Interface, and Johnson Controls VMA1400 Series Digital Controller 8 TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin

TE-7730-0 RECEIVER ANALOG INTERFACE RF SIGNAL Tstat LOW BATTERY 24 VAC TE-7730 Series RF Receiver with Analog Interface 24 VAC COMMON OCCUPANCY RELAY LOW BATTERY RELAY RELAY COMMON ZONE TEMPERATURE OUT SET POINT OUT OUT COMMON RF ADDRESS REMOVE FOR AS-AHU, DX-9100 Note: Remove Jumper J1 for Johnson Controls AS-AHU and DX-9100 Series Digital Controller applications that require disabling the manual override status via the zone temperature. Do not remove Jumper J1 for Johnson Controls AS-UNT or AS-VAV Digital Controller applications. Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, or Compatible Competitors Digital Controller To Supply Transformer 24 VAC 24 VAC COM 24 VAC 24 VAC COM OCC BI LOW BAT BI BI COM* TEMP AI-1** SET PT AI AI COM RED BLK BLU YEL GRN WHT ORN BRN Power and Analog Interface with Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, or Compatible Competitors Digital Controller (6 ft Interface Cable Included with TE-7730 Series RF Receiver) RED BLK BLU YEL GRN WHT ORN BRN RF Transmission Signal from to Receiver TE-7710 Series RF Wireless Temperature and Set Point Liquid Bulb Thermometer * Relay Common (green wire) should be connected to either Binary In COM or Binary In SRC, depending on the digital controller. ** Zone Temperature Out (white wire) should be connected to analog input AI-1 of the digital controller (zone temperature). Set Point Adjustment Slider Mounting Base WIRELESS Manual Occupancy Override Pushbutton Pull Tab Access Door Figure 6: TE-7710 Series RF Wireless Temperature and Set Point, TE-7730 Series RF Receiver with Analog Interface, and Johnson Controls AS-AHU, AS-UNT, AS-VAV, DX-9100, or Compatible Competitors Digital Controller TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin 9

Technical Specifications Product and Receiver Models Accessories and Replacement Parts Digital Controller Interface Power Requirements Addressing (, Receiver, and Site Survey Tools) System Accuracy Temperature Indicator Temperature Set Point Transmission Range (, Receiver, and Site Survey Tools) Transmission Intervals Receiver Outputs Mounting Hardware Continued on next page... TE-7720-0 TE-7730-0 TE-7700 Series RF Wireless Room Temperature Sensing System Refer to Table 1. Refer to Table 2. Power and Zone Bus Interface Between TE-7720-0 RF Receiver and VMA1400 Series Digital Controllers Power and Analog Interface Between TE-7730-0 RF Receiver and AS-AHU, AS-UNT, AS-VAV, DX-9100, and Compatible Competitors Digital Controllers One 3.0-Volt Lithium Battery Included with Each ; Battery Life: 36 Months Typical (24 Months Minimum); Battery Condition Transmitted Approximately Every 60 Seconds; Replacement Batteries: Duracell Ultra 123, Panasonic CR123A, Toshiba CR123A, GE/Sanyo CR123A, or Equivalent (Purchase Locally) Receiver 24 VAC +10%/-15%, 50/60 Hz, 4.5 VA, Class 2 Site Survey Tool Receiver Site Survey Tool Measured Temperature Temperature Set Point Type One 3.0-Volt Lithium Battery Included with Each Site Survey Tool; Replacement Batteries: Duracell Ultra 123, Panasonic CR123A, Toshiba CR123A, GE/Sanyo CR123A, or Equivalent (Purchase Locally) Three 3.0-Volt Lithium Batteries Included with Each Site Survey Tool; Replacement Batteries: Duracell Ultra 123, Panasonic CR123A, Toshiba CR123A, GE/Sanyo CR123A, or Equivalent (Purchase Locally) DIP Switches, Field Adjustable for up to 510 Unique Addresses (Addresses 0 and 511 are Invalid) ±1F (±0.6C ) Over a Range of 55 to 85 F (13 to 29 C); ±1.5F (±0.9C ) Over a Range of 32 to 55 F (0 to 13 C) and 85 to 110 F (29 to 43 C) ±1.5F (±0.9C ) Over a Range of 55 to 85 F (13 to 29 C) Liquid-Filled Bulb Thermometer Range 55 to 85 F or 13 to 29 C Resolution Fahrenheit Scale Graduated in 10F Intervals; Celsius Scale Graduated in 5C Intervals Adjustment Single Temperature, Scaled F/ C Resolution Site Survey Tools TE-7720-0 TE-7730-0 Receiver Fahrenheit Scale Graduated in 5F Intervals; Celsius Scale Graduated in 2C Intervals 1 Mile or 5,280 ft (1,609.3 m) Maximum in Open Air; 1,000 ft (304.8 m) Maximum for Indoor Line-of-Sight; 200 ft (61 m) Practical Average Indoors Every 60 Seconds (±20 Seconds) Every 5 Seconds (±2 Seconds) One Zone Bus Output for Temperature, Set Point, Field Strength Measurements, and Low Battery Indication Two Analog Outputs for Zone Temperature and Set Point: 0 to 5 VDC, 2 ma Maximum; Two Binary Outputs for Occupancy and Low Battery Indication: Dry Contacts Rated for 24 VAC, 50 ma Maximum Two Expandable Wall Anchors (Preferred Mounting Method) or Double-Sided Adhesive Foam Tape Four No. 6 Sheet Metal Screws 10 TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin

Technical Specifications (Cont.) Ambient Operating Temperature Limits Ambient Storage Temperature Limits (, Receiver, and Site Survey Tools) Ambient Humidity Limits (, Receiver, and Site Survey Tools) Materials Standards Compliance Receiver Terminations Cable Between Receiver and Johnson Controls Digital Controller Continued on next page... and Site Survey Tool Receiver and Receiver Site Survey Tool Operating Storage and Site Survey Tool Receiver and Receiver Site Survey Tool United States Canada Australia and New Zealand TE-7720-0 TE-7730-0 TE-7720-0 TE-7730-0 0 to 122 F (-18 to 50 C) 32 to 122 F (0 to 50 C) -40 to 160 F (-40 to 71 C) 5 to 95% RH, Noncondensing 5 to 90% RH, Noncondensing NEMA 1 White Plastic Housing Gray Plastic Housing with UL94-5VB Flammability Rating NEC Class 2 Compliant UL 916 Energy Management Equipment (UL) UL94-5VB Flammability Rating (Receiver Housing is Plenum Rated per UL 1995 Heating and Cooling Equipment) FCC Compliant to CFR 47, Part 15, Subpart B, Class A Transmission Complies with FCC Part 15.247 Regulations for Low Power Unlicensed s ( FCC Identification: L2V AX630) CSA C22.2 No. 205 Signal Equipment (cul) Industry Canada ( Industry Canada Identification: IC 279A-TE7710XX) Australia/NZ Emissions Compliant (C-Tick Mark) Two Spade Terminals that Accept One Two-Position, Screw-Terminal Pluggable Block (Pluggable Block Included with Receiver) Eight Spade Terminals that Accept One Two-Position and Two Three-Position, Screw-Terminal Pluggable Blocks (Pluggable Blocks Included with Receiver) 6 ft (1.8 m) Power and Zone Bus Interface Cable Included with Each Receiver; Cables to Connect Zone Bus Only (No Power) Measuring 25 ft (7.6 m), 50 ft (15.2 m), 75 ft (22.9 m), and 100 ft (30.5 m) are Available (Refer to Table 2.) 6 ft (1.8 m) Power and Analog Interface Cable Included with Each Receiver TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin 11

Technical Specifications (Cont.) Dimensions Shipping Weights and Site Survey Tool Receiver and Receiver Site Survey Tool and Site Survey Tool Receiver and Receiver Site Survey Tool 3-3/16 in. Long x 3-3/16 in. Wide x 1-13/32 in. High (81 mm Long x 81 mm Wide x 36 mm High) 4-23/32 in. Long x 5-29/32 in. Wide x 1-31/32 in. High (120 mm Long x 150 mm Wide x 50 mm High) 0.3 lb (0.14 kg) 1.0 lb (0.45 kg) The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. Controls Group 507 E. Michigan Street P.O. Box 423 Milwaukee, WI 53201 Published in U.S.A. www.johnsoncontrols.com 12 TE-7700 Series Radio Frequency (RF) Wireless Room Temperature Sensing System Submittal Bulletin