HZ104100TX Black Contemporary Bar Cabinet Assembly Instructions For assistance with assembly contact: Southern Enterprises, Inc. customer service 1-800-33-09 service@seidal.com www.seidal.com PO#: Page 1
Black Contemporary Bar Cabinet Parts list Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures. Using the incorrect hardware will cause damage. A B C top panel D bottom panel E left side panel F u p right side panel G of 3 fixed shelf panel H back panel I wine rack shelf panel J wine rack vertical panel K left door L right door M door shelf panel N O drawer front left drawer side right drawer side drawer back Page 2
P Q R drawer bottom S middle glass rack T side glass rack 1 of 32 legs 2 of 32 metal rack 3 of 32 wood dowel Dia /1 x 1-3/1 L 4 of cam bolt of 8 cam lock 2 hinge 7 short screw: Dia 1/8 x 1/2 L 8 round head screw: Dia 1/8 x 1/2 L 9 knob 10 small bolt 11 magnet 12 left female slide 13 left male slide right female slide right male slide Page 3
14 1 8 1 L bracket 17 long screw: Dia 1/8 x 1-1/4 L 18 medium screw: Dia 1/8 x 1 L 19 wall bracket screw: Dia 1/8 x /8 L 20 wall bracket 21 plastic strap anchor wall screw: Dia 1/8 x 1-3/8 L Care and cleaning instructions: Before using, wipe with a clean, dry cloth. For replacement parts or questions, please Periodically apply furniture wax to renew call customer service at 1-800-33-09 the finish. Avoid rubbing or scratching the surface with rough or abrasive objects. Assembly Tool Required No.2 Phi Assembly Tool Required No.2 Phillips Screwdriver (Not included) Tool List: 3/1" drill bit, drill, tape measure and pencil. Page 4
Black Contemporary Bar Cabinet Assembly Instructions Wood may scratch easily, be careful when assembling. Attach left female slide (10) to left side panel (C) with short screws (). Tighten short screws () with a phillips Tip: Make sure to attach short screws () in the same hole on left female slide (10) as shown on inset. If you have correctly attached one screw, every other screw should align with the holes on female left slide (10). The front of the panel can be distinguished by the finish. Figure 1 Attach right female slide (12) to right side panel (D) with short screws (). Tip: Make sure to attach short screws () in the same hole on right female slide (12) as shown on inset. If you have correctly attached one screw, every other screw should align with the holes on right female slide (12). Figure 2 Page
Figure 3 C E E 3 D Insert cam locks (3) into holes on fixed shelf panels (E) Screw cam bolts (2) into holes on left side panel (C). Attach left side panel (C) to fixed shelf panels (E) by inserting wood dowels (1) and cam bolts (2) into corresponding holes until left side panel (C) and fixed shelf panels (E) meet. Tighten by rotating cam lock (3) clockwise with a phillips screwdriver Repeat procedure to attach right side panel (D) to fixed shelf panels (E) Insert cam locks (3) into holes on pre-assembled unit. Screw cam bolts (2) into holes on the bottom of top panel (A). Attach top panel (A) to pre-assembled unit by inserting wood dowels (1) and cam bolts (2) into corresponding holes until top panel (A) and pre-assembled unit meet. Tighten by rotating cam locks (3) clockwise with a phillips Figure 4 Attach magnet (9) to top panel (A) with round head screw (). Insert cam locks (3) into holes on pre-assembled unit. Screw cam bolts (2) into holes on the top side of bottom panel (B). Attach bottom panel (B) to pre-assembled unit by inserting wood dowels (1) and cam bolts (2) into corresponding holes until bottom panel (B) and pre-assembled unit meet. Tighten by rotating cam locks (3) clockwise with a phillips screwdriver Figure 2 1 2 B Attach magnet (9) to bottom panel (B) with round head screws (). Page
Attach legs (S) to pre-assembled unit by hand. Attach middle glass racks (Q) and side glass rack (R) to pre-assembled unit with wood dowel (1) and long screws (1). Tighten long screws () with a phillips R Figure Attach wine rack vertical panel (H) and wine rack shelf panel (G) together as shown. Figure 7 Insert pre-assembled wine rack to the unit from the back as shown. Figure 8 Page 7
up Attach back panel (F) to the backside of pre-assembled unit with round head screw (). Tip: Make sure the arrow on back panel (F) is pointing up. F Figure 9 I/J T 8 7 T Attach metal rack (T) to left door (I) and right door (J) with short screws (). Attach knob (7) to left door (I) & right door (J) with small bolts (8). Tighten screws and small bolt with a phillips Figure 10 2 2 Insert cam locks (3) into holes on door shelves (K). Screw cam bolts (2) into holes on pre-assembled doors. Attach door shelves (K) to pre-assembled doors by inserting wood dowels (1) and cam bolts (2) into corresponding holes until door shelves (K) and pre-assembled doors meet. Tighten by rotating cam locks (3) clockwise with a phillips Repeat steps for the second door. Figure 11 Page 8
Attach L brackets (14) to pre-assembled doors with screws (). Figure 12 Attach hinges (4) to the sides of the pre-assembled unit with short screws (). 4 4 4 4 Figure 13 Page 9
2 Attach the left drawer side (M) and right drawer side (N) to drawer back panel (O). Make sure to line up the grooves on panels (O, N, and M). Secure panels (O, N, and M) with medium screws (1).Insert drawer bottom panel (P) into the corresponding grooves of drawer back panel (O) and left drawer side (M) and right drawer side (N). Insert cam locks (2) into predrilled holes on left drawer side (M) and right drawer side (N). Screw cam bolts into holes on the backside of drawer front (L), Attach drawer front (L) to pre-assembled drawer box by inserting cam bolts (2) into corresponding holes until drawer front (L) and pre-assembled drawer box meet. Figure 14 Tighten by rotating cam locks (3) clockwise with a phillips Attach left male slide (11) and right male slide (13) with short screw () to pre-assembled unit. Figure 1 Page 10
Insert drawer box into the unit. Please check to make sure the drawer box male slides are inserted into side panel s female slides. Figure 1 wall 2 0 1 8 2 1 2 0 1 8 2 1 Attach wall bracket (18) to the back panel using wall bracket screw (17). Tighten wall bracket screw (17) using a phillips 1 8 1 7 Mark two desired locations on the wall and drill two 3/1" holes. Insert plastic anchors (20) into the two holes on the wall as shown, you will need a hammer help you. Then attach the wall bracket (18) to the wall using wall screws (21). Tighten wall screws (21) using a phillips Figure 17
Move this item close to the wall and tie both wall brackets (18) with plastic strap (17) as shown in diagram. Anti-tipping hardware must be used for this product to avoid tipping and injury. Figure 18 Your black contemporary bar cabinet is ready for use. Figure 19
Parts Replacement Form Page 11 Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Needed Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise. Please contact Southern Enterprises at 800-33-09 or in Dallas 972-89-0111/ 9am 4pm Mon-Fri Central time if you have product issues or email us at service@seidal.com. Please ask for customer service representative for issues involving damages or replacement parts. Please ask for technical assistance representative for any issues with product and assembly/construction. Please contact the retailer that you purchased from for returns. Customer Service 1-800-33-09 service@seidal.com Southern Enterprises, Inc. 00 Freeport Parkway, Suite 200 Coppell, Texas 7019 Page 12