Model Name : Features : ㅡ Flickerless ㅡ Full-protection provided: OCP/OVP/OTP/SCP/OLP ㅡ Low Power Dissipation (Stand-by mode : <0.5Wh) ㅡ Wide Vout : 25 ~ 50Vdc ㅡ UL8750 / UL1310 ㅡ Compliant with CB, CE, UL safety requirements for LED lighting ㅡ Constant Current Type ㅡ IP 67 E480967
Electrical specification No. 1 4 5 6 Nominal Input Voltage 120 Nominal Input Frequency 47 50/60 Power Factor (PF) 90 - - % Total Harmonic Distortion (THD) - - 20 7 Inrush Current - - 60 A 8 11 12V Output Voltage 10.8 Min Typ Max Unit Remark 100 3.75 - - - - % Vdc Wh Storage Temperature -40 25 80 Dielectric Withstand Voltage Electrical Efficiency 84 87-9 Turn-on Delay 10 12 13 14 15 Output Open LED Protection Input to Case - - - Hz 700 735 ma LED Output Voltage 25-50 Vdc Adjustable of LED Current 12V Output Current 500 700 12 13.2 17 STBY Power Dissipation - - 0.5 18 21 22 23 25 26 27 31 ESD Item LED Output Current 665 Operating Temperature Humidity 20 Input to Output Output to Case Contact Discharge Air Discharge - - 0.5 s ma - - - - % 1) % 1) ma 2) @Cold Start, 3) @50Vdc Load 2) 20 MHz Bandwidth, 2) Rset Vdc 2) ma - - 59 Vdc 28 Line to Line 6 7 - Surge 29 Line to Ground 8 9-4 - 8 220 277 2 Variable Input Voltage 108-300 Vac 3 Maximum Input Current - - 0.4 Arms 16 19 20 LED Output Current Ripple - - 70 12V Output Voltage Ripple - - ± 1.2 Output Short Circuit Protection 25 50-85 24 Insulation Resistance 10 - - MΩ 30-40 Case Temperature (Tc) - 50 85 0.5-63 3.75 - - - - Vac 20 MHz Bandwidth, 2) LED Off_Remote Low @Vpeak No Damage Ta = 60 500Vdc between Input & Output Apply for 1 minute 6) 4) 4) 5) 5)
Application Notes 1) Test Condition:120/277Vac 50/60Hz Input,Typical LED Load,Ambient Temperature 25, Measure at the cable-end 2) Test Condition: 220Vac 60Hz Input, LED Max. Load, 30min Aging, Ambient Temperature 25 3) The interval of turn on/off should be over 1sec. 4) Surge Specification above is higher than IEC/EN 61000-4-5 Level 4 (Differential 2, Common 4 ) 5) The metal case of the LED driver must be connected with F.G 6) ESD Specification above meets IEC/EN 61000-4-2 Requirements (Contact Level 2, Air Level 3) 7) The metal case of the driver should be grounded. 8) Determined by Paragraph 34.1.2, UL1310 or Paragraph 8.4.2, UL8750, EN61347-1, EN61347-2-13 Safety Standards Including safety requirements above, the LED driver complies with the following safety standards: No. Item Description 1 UL8750, UL1310 UL Safety Standards (Class 2, Dry and Damp Location) 2 IEC/EN 55015 Conducted and Radiated Emission Test 3 IEC/EN 61000-3-2 Harmonic current emissions: Class C 4 IEC/EN 61000-3-3 Voltage Fluctuations and Flicker 5 IEC/EN 61000-4-2 Electrostatic Discharge (ESD): Contact Level 2, Air Level 3 6 IEC/EN 61000-4-3 Radio-frequency Electromagnetic Fields 7 IEC/EN 61000-4-4 Electrical Fast Transients (EFT) 8 IEC/EN 61000-4-5 Surges: Level 4 9 IEC/EN 61000-4-6 Injected Currents 10 IEC/EN 61000-4-8 Power Frequency Magnetic Fields 11 IEC/EN 61000-4-11 Voltage Dips and Short Interruptions
Operating window Preliminary *Currently Measurement Data Life Time vs Tcase 120000 100000 Life Time [hrs] 80000 60000 40000 20000 120Vac_16S(50V) 220Vac_16S(50V) 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Tc [ ] Remark) LED Driver has a rated lifetime of 50,000 hours @ Tc 70
*Currently Measurement Data Power Factor(%) 100.00% 9LED-500mA 90.00% 9LED-700mA 80.00% 12LED-500mA 70.00% 60.00% 16LED-500mA 50.00% 16LED-700mA 120 220 277 Input Voltage (Vac) Power Factor THD(%) THD 35.00% 30.00% 25.00% 20.00% 15.00% 10.00% 5.00% 0.00% 120 220 277 Input Voltage (Vac) 9LED-500mA 9LED-700mA 12LED-500mA 16LED-500mA 16LED-700mA Efficiency(%) Eff 100.00% 90.00% 80.00% 70.00% 60.00% 50.00% 120 220 277 Input Voltage (Vac) 9LED-500mA 9LED-700mA 12LED-500mA 16LED-500mA 16LED-700mA
Output Current( ma ) Current 800.00 700.00 600.00 500.00 400.00 300.00 200.00 100.00 0.00 Dimming curve 120 220 277 Input Voltage (Vac) Preliminary *Currently Measurement Data 9LED-500mA 9LED-700mA 12LED-500mA 16LED-500mA 16LED-700mA Current 800.00 700.00 600.00 500.00 400.00 300.00 200.00 100.00 0.00 10 9.3 9 8 7 6 5 4 3 2 1 0 Dimming Voltage (Vdc) 9LED-500mA 9LED-700mA 12LED-500mA 15LED-700mA Adjustable of Current( Rset ) 750 LED Current[mA] 700 650 600 550 500 1,000 10,000 100,000 1,000,000 Rset [Ω] Rset
Mechanical Specification TOP BOTTOM Enclosure Size Unit Width Length Height Mount Length Overall Length mm 53.6 177.6 33.9 185.4 192.6 inch 2.11 6.99 1.33 7.30 7.58 Case Material : Aluminium
Wiring Diagram LIVE : Black Neutral : White Caution L N 1) Before installing LED driver, AC power should be turned off. After installing LED driver, AC power should be turned on. 2) When this LED driver are installed as an independent lamp controlgear, end-customer should protect connecting leads of pri/sec. cable with a certified element. 3) Waterproof connector or Junction box can be assembled with output cables for operating in dry/wet/damp or outdoor environment. LED Control gear 4) Wires should be less than 1m when installed in final equipment L L E S D R V G G LED + : Red LED : Blue Vsen : White Rset : Orange DIM : Violet RMT : Green 12V : Yellow GND : Black GND : Blue 2nd Signal Description Name Vsen Rset DIM RMT 12V GND GND Feature check LED Out Voltage Adjustable of current Dimming LED On/Off Control Source 2nd GND 2nd GND Purpose Monotoring LED Open/Short (for Connectivity Module) Control LED Output Current Control Brightness Stand by Mode Supply Controller Power Signal GND Signal GND Rating Label Drawing
Barcode Label Box Label Material Code ITEM LOT No REV. A** ********* MAKER USER Model Code SOLUM Model Code SOLUM LOT NO & Quantity of Products Quantity [PCS] 24 SOLUM EXP. Date 20**.**.** ~ 20**.**.** Product Date ~ After 5 years ************* **** ********* USER Barcode
Packing Drawing 1. Out Box Dimmension Weight Quantity 540(L) 355(W) 170(H) [mm] < 14Kg 24EA / 1Box TRY BODY NIL PAD OUT BOX 2. Pallet