TM I N S TA L L AT I O N I N S T R U C T I O N S
READ THESE INSTRUCTIONS page 2 Installer Tips: Installation is best completed with the help of one or two people. Prior to beginning, please read through all instructions pertinent to your installation. (Doors, panels, etc...) Panels are to be installed horizontally between posts, parallel with the ground. Prior to beginning, if at all possible lay out the parts where they are to be installed. Make sure all posts are installed perpendicular to the floor, shims may be required. Use 3.5 spacer block (NOT SUPPLIED) to support the panel during the installation on one side if only one person is installing panels. See 2A on page 3 Standard partitioning assembly Begin installation at a wall (if your plan calls for a wall connection), using a 2.5 post at wall. Hinge door opening is determined by transom. Consult your plan for location and dimensions. Temporarily install transom at floor level. Assembly hooks will be installed on the inside of enclosure. Self-Tapping Screw Installation Recommendations: When installing self-tapping screws use a standard variable speed screw gun equipped with an adjustable clutch or depth locating nosepiece. Take care not to over tighten or strip, set the drill accordingly. DO NOT USE IMPACT TYPE GUN WHEN INSTALLING SELF-TAPPING SCREWS. Because screws could strip, securely clamp component parts in place before attaching with self-tapping screws. If screws are overtightened and strip, drill through post and use bolts (NOT SUPPLIED) of adequate size. Tools Required: 1/2 masonry bit (drill holes in floor for post) 3/8 wrench or socket (screws for attaching door parts) 1/2 wrench or socket (screws to secure panels if used instead of drive rivet) 3/4 wrench or socket (secure nuts on floor anchor) 7/16 wrench or socket (various 1/4 bolts for ceiling, panel kits plates, etc.) Phillips screw driver (install lock) Small Hammer Parts Recommended: Floor Anchors (Part #H5814 in Kit Post. 1/2 x 3-3/4 ) and Matrix Shims (Part #H5820 in Kit Post) Drill Bits (Various) Flat Screw Driver Tape Measure Electric Screw Gun Safety Items (hardhat, gloves, safety glasses & steel toed work shoes); remove jewelry The following installation instructions should be used as a guide for installing Wireway Husky EZ-Matrix Partitions. Good common sense and appropriate safety precautions must be used during installations. The product may be unstable during installation; accordingly - temporary bracing should be used until all hardware is tightened and the product is properly anchored to the floor. Permanent field bracing (NOT SUPPLIED) may be installed. Call Factory. Installation problems arising from job site conditions should be referred to a professional installer. Refer product assembly questions to Wireway Husky Corp. 800-438-5629. Tools Recommended: Safety Ladder (most jobs too tall to reach from floor) Carpenter Level Chalk Line Heavy Duty Wire Cutters Prior to Installation: Prior to beginning installation please check bill of lading to make sure that you have all the parts required for the assembly Make sure that the installation area is clear of all obstructions Read thoroughly all the instructions pertinent to your installation Safety Items Safety gloves, hard hat and safety glasses should be worn during installation.
STANDARD PARTITION ASSEMBLY 8 and 10 Panel Arrangements Screws page 3 5 LINE POST 2-1/2 SQ 46-3/16 6 Hardware 1/2 Nut and washer 3 INSTALL PANELS HORIZONTALLY 2 FLOOR ANCHOR HEIGHT EZ-Matrix Installation Instructions: - EZ-Matrix installation is best accomplished with two or three persons. - Use a chalkline to mark the partition runs on the floor. Dimensions to be used are outside measurements 1. Right Angles can easily be made by use of a 3-4-5 triangle - see sketch. 3-4-5 triangle 3 4 5 4 INSTALLING DRIVE RIVET - Starting with a line post 5 : lag the first post to the floor using two Floor Anchors 2. Make sure the slots in the tube face inward of the enclosure. - 3 Install the hooks of the first panel in the lagged 2.5 Line Post at the lowest level. Engage the panel s opposing hooks in the next unlagged Line Post. Install one heavy-duty drive rivet per hook for maximum security. - Use 3.5 spacer block (NOT SUPPLIED) to support the panel during the installation on one side if only one person is installing panels. See 2A standard partitioning assembly VIEW FROM OUTSIDE ENCLOSURE 1 CHALK LINE 2A SPACER BLOCK 2 FLOOR ANCHOR - Lag the second 6 2.5 square post to the floor using two Floor Anchors 2. - Install the top panel. Install one per side minimum, but use six drive rivets if desired. Alternate: use removeble 5/16 x 1 self threading Screws (Not included) in place of the 1/4 heavy-duty drive rivet.
STANDARD PARTITION ASSEMBLY page 4 Bottom Panel - First Panel Installed Top Panel - Complete Installation FIRST POST 4 INSTALL TOP PANEL SECOND POST 5 ADD MID PANEL CLIP 1 LAG FIRST POST IN PLACE 2 INSTALL PANEL AND SECOND POST 3 LAG SECOND POST IN PLACE VIEW FROM OUTSIDE ENCLOSURE
DOOR ARRANGEMENTS Sliding Doors page 5 1. Door opening width: The distance between 2-1/2 square line posts is determined using transom overhead (if present) Measuring width of the door opening minus 1-3/4. If transom is used (See page 8) install temporarily at base of door opening to establish precise opening width (used in swing and slide doors). 2. Customer to install lock. (See pages 10-11). 3. Attach two 4 wheel trolley into the door 1/2 diameter holes provided. (See page 6). 4. Using two 5/16 x 3 carriage bolts, attach the bottom slam. Using two 5/16 x 3 carriage bolts, attach the latch receiver. (See page 14). 5. Fasten the track bracket assembly (See page 6 B ) to the post on either side of the door opening using 1/4 x 1 hex head self threading screws. 6. Install the door track in the track bracket assemblies. Secure the track by tightening the set screws provided in the two track brackets. 7. Slide the door s trolleys into the overhead track. (See page 6). 8. Install a track bumper as a keeper for the door trolley. (See page 7). 9. Attach the bottom guide as shown on page 7.
DOOR ARRANGEMENTS Single Sliding Door page 6 Sliding Door Assembly for 6, 8 and 10 Doors B 4 WHEEL TROLLEY TRUCK END OF TRACK IF POST IS AVAILABLE. OTHERWISE, USE MID-PANEL BRACKET. FOR DETAILS SEE PAGE 5 OPENING MUST BE WIDTH OF DOOR MINUS 1-3/4 4 WHEEL TROLLEY IN THE DOOR
FOR DETAILS SEE PAGE 5 DOOR ARRANGEMENTS Double Sliding Door page 7 TRACK BUMPER RUBBER BUMPER TRACK BUMPER (Used to stop slide door trolley (to prevent overtravel of door trolleys) BOTTOM GUIDE CANE BOLT-PADLOCK HASP PROVIDED (Lock into floor when doors in closed position) OPENING MUST BE WIDTH OF DOOR MINUS 1-3/4
DOOR ARRANGEMENTS Swing Door page 8 HEADER ONLY USED WHEN TRANSOM IS NOT USED. (FULL HEIGHT DOOR) Temporarily install door transom at bottom to establish proper door opening. Come back later to finish door installation. SINGLE SWING DOOR DOUBLE SWING DOOR 1. The opening between line posts for a hinged door installation is exactly equal to the installed transom width. 2. Install the Transom and fasten the line posts to the floor. 3. Install the cylinder lock or padlock attachment with the door in a horizontal position. See page 9.
HINGED DOOR PADLOCK ATTACHMENTS page 9 INSERT ATTACHMENT THROUGH SLOT AS SHOWN DRILL THROUGH AND BOLT Swing Door Hardware
LOCK OPTIONS page 10 DOOR/GATE LOCKS Key Lock Thumb-Turn Latch Door Knob Entry Interior Key Door Knob Lever Handle SWING DOOR - INSIDE VIEW SWING DOOR - OUTSIDE VIEW Can Be Hinged Left = Swing out; or Hinged Right = Swing in ELECTRICAL LOCKING DEVICES Coded Card Reader Ten-Digit Key Pad Electro-Magnetic Lock Electric Strike Master Lock ADA Handle Five-Button Coded Access Lock Push Paddle Push Bar Alarm Lock SLIDE DOOR - INSIDE VIEW SLIDE DOOR - OUTSIDE VIEW
LOCK ASSEMBLY page 11 SLIDE DOOR LOCK - INSIDE VIEW SWING DOOR LOCK - INSIDE VIEW
MID PANEL CONNECTION page 12 MID PANEL - OUTSIDE VIEW MID PANEL - INSIDE VIEW MID PANEL SUPPORT BAR MID PANEL CONNECTOR
HARDWARE ITEMS page 13 1 One way Screw Universal Metal Shim 1/2 Washer Double Hook Clips (For Custom Fit Panels) For Corners 1/2 Nut Drive Rivet 1-1/4 Hex Screw 1-5/8 Bolt For Posts 3-3/4 Lag Slide Door Track MID PANEL TRACK BRACKET (Used for attaching slide door track bracket to mid panel where no posts are available.) 4 WHEEL TROLLEY TRUCK FOR SLIDE DOOR continued...
SLIDE DOOR HARDWARE ITEMS page 14 Bottom Guide LATCH RECEIVER Latch Receiver BOTTOM SLAM 4 WHEEL TROLLEY TRUCK Bottom Slam LATCH RECEIVER AND BOTTOM SLAM ON POST (Bolts to install included) MID PANEL TRACK BRACKET
VIEW FROM OUTSIDE ENCLOSURE CEILING SUPPORT Ceiling Panel Assembly CEILING CLIP CEILING TUBE CONNECTION page 15 Hook easily installs into post for a secure fit. 2-1/2 TUBING BACK CLIP SCREW VIEW FROM INSIDE ENCLOSURE
APPLICATIONS MID PANEL TRACK HANGER USED AT CORNERS page 16 MARKET SEGMENTS Communications Industry Residential Manufacturing Government and Military Retailers and Restaurants DEA Applications Warehousing, Office MID PANEL CLIP
TROUBLESHOOTING TIPS page 17 Swing Door: Door does not latch - make sure post are level and plum - make sure distance between post is the same as at transom and bottom. - turn key and/or thumb turn to see if tongue retracts. - make sure lock tongue and strike bar receiver align. - make sure lock tongue is facing in proper position. Rounded face of tongue should always contact the strike bar. Slide Door: Door does not latch - make sure Post are level and plum - make sure tounge is installed with rounded end up - make sure tounge is aligned with latch receiver - turn key and see if tongue retracts down. - adjust hight and tilt of door with top trolley bolts.
CUSTOM PANEL page 18 Cut-To-Fit Six clips are included with your order. Panels can be cut with 2 adjustability. VIEW OF HOOK AND POST OUTSIDE ENCLOSURE VIEW OF HOOK AND POST INSIDE ENCLOSURE DRIVE RIVET HEAD RIVET END - FLARED TAMPER PROOF BACKPLATE DOUBLE HOOK FASTENER CUSTOMIZED (SPECIAL WIDTH PANELS)
POST EXTENSIONS page 19 2-1/2 Tubular Posts Heavy duty 2-1/2 tubular posts are double the strength of 2 square commercial tubing. 1 1 DRIVE RIVET INSTALLED AT FACTORY SPLICE TUBE ENGAGING BOTTOM POST Use flathead screwdriver to align spliced post to bottom post
CORNER POST EXTENSIONS page 20 Corner Posts SPLICE CORNER TUBE ENGAGING BOTTOM POST
TERMS AND CONDITIONS page 21 It is the intent of Wireway Husky Corp. that any product received by our Customers fully meets their expectations. Wireway Husky product is Marketed and Distributed by a number of pre-qualified Distributor organizations around the world. If you have any questions about the applications or installation of your product or, in the event that this product is received by you in a form you believe to be sub-standard or below expectations, please contact the Distributor responsible for specifying and suppling your product. If for some unforeseen circumstance the particular Distributor is unavailable or unresponsive, we then encourage you to call Wireway Husky All parts subject to change without notice 2008, Wireway Husky Corp. All Rights Reserved. Ches #12527