Owner s Manual 200200C Coin Counter & Sorter
TABLE OF CONTENTS 1. Product Views Front and Rear Views Display 2. Operation Modes Counting Mode Power Saving Mode Batch Mode Coin Tube Attachments 3. Troubleshooting Error-Message Display Codes 4. Specifications 5. Safety/Warnings Cleaning the Machine Maintenance Notice 6. Warranty Page 2 3 4 4 5 6 7 8 9 10 11 1
1. PRODUCT VIEWS 200200C Front and Rear Views 1 2 3 1. Control Panel 2. Coin Hopper 3. Coin Trays 4. Coin Tubes 5. Handle 6. Coin Access Panel 7. Power Button 5 6 4 7 2
1. PRODUCT VIEW Display 5 6 PRINT 7 1 BAT SET CLEAR 2 4 3 1. Start/Stop Key 2. Clear Key 3. Set Key 4. Batch Key 5. (Minus) Key 6. + (Plus) Key 7. Print Report Key 3
2. OPERATION MODES 200200C COUNTING MODE 1) Remove all uncounted coins from the machine during the previous count 2) Batch amounts need to be a "0" for each denomination a. Press "Set" key to view batch amounts by denomination b. Press "Clear" key to set the 0.01 (penny) to 0 c. Press "Set" key to move arrow down to next denomination d. Continue steps b and c above until all denominations are set to "0" 2) Place the coins into the hopper and press the "Start/Stop" key 3) The machine will start counting while sorting the coins 4) The machine will stop automatically when all coins in the coin hopper are counted 5) You can add more coins and the totals will continue from the last count or press the "Clear" key to reset POWER SAVING MODE The machine will enter sleep mode after 5 minutes. It can be returned to working mode by pressing any key. 4
2. OPERATION BATCH MODE This mode allows you to batch a specific quantity of each coin denomination. Standard batch quantities for coin rolls: Coin Batch Amount Pennies 50 Nickels 40 Dimes 50 Quarters 40 Dollars 25 Custom batch quantities: 1) Press "Set" Key to view batch amounts by denomination 2) Press "Batch" Key to raise the batch amounts by the following increments: 0.01 10 for each "Batch" key pressed 0.05 10 for each "Batch" key pressed 0.10 20 for each "Batch" key pressed 0.25 20 for each "Batch" key pressed 1.00 20 for each "Batch" key pressed 3) Press "-" or "+" key to increase amount by 1 lower or higher 4) Press "Set" key to move to the next denomination 5) Continue steps 2-4 until all batch denominations are set 6) Place the coins into the hopper and press the "start/stop" key 7) The machine will start counting while sorting coins 8) The machine will stop automatically when the batch quantity for the denomination is reached 5
2. OPERATION (CONTINUED) 200200C Coin Tube Attachments The coin tube attachments allow you to sort coins directly into standard, paper roll wrappers. 1) Remove the coin tray(s) 2) Insert wrapper into the coin tube with the crimped end down. Make sure the top of the wrapper is below the top of the coin tube 3) Slide coin tube(s) into the proper coin slot 4) Set the coin roll batch quantities see Batch Mode 5) Load coins into the hopper and press the start/stop key 6) When the selected amount of coins is obtained, the unit will stop. Remove the full tube and repeat steps 2 & 3 above 7) Press the "Start/Stop" key to continue 6
3. TROUBLESHOOTING Error-Message Display Codes Error Code Meaning Remedy E1 - E8 Counting sensor error Clean the counting sensor E9 Coins remaining in the machine Remove remaining coins from the machine E10 Motor detecting sensor error Make sure 2 screws for motor sensor are in and in alignment 7
4. SPECIFICATIONS 200200C Specifications Dimensions: 14.2" x 11.1" x 13.4" (W x H x D) Weight: Counting Speed: 9.3 lbs 345 coins/min Power Consumption: Maximum 45W Power Source: 110VAC / 60 Hz Control Panel Screen Size: 1.5" x 2.75" Hopper Capacity (Pennies): 1,650 8
5. SAFETY/WARNINGS Cleaning the Machine Warning: Before doing any cleaning, turn the power switch off and disconnect the power cord. 1. External: a) Using a compressed air duster or soft cloth, clean all external parts of the machine. Do not use cleaning solvents. 2. Internal a) Remove 3 external screws around the housing b) Carefully lift up housing and make sure not to disturb connected wires c) Using a compressed air duster or soft cloth, clean the sensors and other dirty parts d) Set the housing back on the unit, make sure internal wiring is not exposed and power button is aligned 9
6. WARRANTY 200200C Maintenance Notice 1) Do not put fingers inside the coin hopper or channel when the machine is in operation 2) The machine must be safely connected to the power source 3) The machine must be used and kept in dry location. Do not operate in high temperatures, humidity or smoke 4) Only use supplied power cord 5) Do not start the machine with the coin access panel open 6) Do not open the coin access panel when the machine is working 10
Warranty STEELMASTER provides a limited, one-year replacement warranty for this unit (200200C). This warranty is limited and conditional as the following: One-year from the date of original purchase. Applies only to the original purchaser. All warranty claims must be accompained by the proof of purchase. Warranty is limited to defects in workmanship or material. It does not apply to damages in handling the product, general misuse, poor maintenance or shipping. Warranty liability does not extend or cover any loss, harm or damages from miscounts or failures in coin counting. Warranty does not guarantee the absolute accuracy of the unit in all environments and conditions. The warranty allows for the replacement of this or similar unit within the warranty period only and STEELMASTER discretion. All warranty returns must be authorized in writing and proper approved forms included in the prepaid return package. All approved warranty returns need to be returned to: Block, Inc.; MMF Division 1111 Wheeling Road Wheeling, Illinois 60090 USA Customer Service/Support 800.323.8181 11
FEATURES Notes 200200C 12
FEATURES Notes 13
1708072