P-Q Controls, Inc. Doc. No: part_numbering_110.doc Phone (860) 583-6994 95 Dolphin Road Rev: A Date: 3.17.2008 Fax (860) 583-6011 Bristol, CT, 06010 MODEL 110 PART NUMBERING (Hall Effect Only) For special configurations, please call for assistance M110 S BD FT CS 56 Author: MSOffice Page: 1 of 1 MODEL M110 Foot Pedal SPRING S (Standard) H (Heavy) Ordering non-standard spring may increase lead time MECHANICAL OPTION BD (bi-directional) UD (uni-directional) ELECTRICAL OPTION CASE OPTION NC (No Case) Mating connector sold separately. PQ#: A-09014-05 CS (Case w/ Strain Relief & Deutsch conn.) CT (Case w/ terminal block) TREADLE OPTION FT (Full Treadle) HT (Half Treadle) NT (No Treadle) Deutsch Connector Terminal Block ELECTRICAL OPTIONS 56 = 10-30VDC, 2.5V NTRL ± 1.5V, 1.5 AMP DIR. AUX OUT 57 = 10-30VDC, 2.5V NTRL ± 1.25V, 1.5 AMP DIR. AUX OUT 58 = 5VDC, ± 30%, NO DIRECTIONAL AUX OUT 59 = 5VDC, ± 40%, NO DIRECTIONAL AUX OUT 60 = 18-60VDC, SEVCON, 1.5 AMP DIR. AUX OUT 61 = 10-30VDC, 2.5V NTRL ± 2.0V, 1.5 AMP DIR AUX OUT 62 = 10-30VDC, DANFOSS 63 = 10-30VDC, 0.0V NTRL + 10.0V, 1.5 AMP DIR AUX OUT 64 = 10-30VDC, 2.5V NTRL ± 1.5V, 1.5 AMP 50% DIR. AUX OUT 65 = 18-60VDC, PWR PAK SVCN, 0.2 AMP SINK DIR. AUX OUT 67 = 10-30VDC, 0.0V NTRL + 5.0V, 1.5 AMP DIR AUX OUT 68 = 10-30VDC, 2.5V NTRL ± 2.0V, 1.5 AMP 50% DIR. AUX OUT 69 = 5VDC, ± 10%, NO DIRECTIONAL AUX OUT 70 = 5VDC, ± 25%, NO DIRECTIONAL AUX OUT 71 = 10-30VDC, 4-20mADC (4mADC NTRL, 20mADC ends) 1.5 AMP DIR. AUX OUT 72 = 10-30VDC, 4-20mADC (12mADC NEUT, 4 and 20mADC ends) 1.5 AMP DIR. AUX OUT 73 = SPLIT SUPPLY INPUT (0vdc NEUT, POS. VS & NEG. VS @ ENDS) 15mAMP DIR. AUX OUT If you do not see your option listed, please call for assistance. Valve Drive Board may be required to control hydraulic valve (sold separately) For more details of electrical options, please see pages 4-5 of Datasheet M110. Property of P-Q Controls, Inc.
Application: The Model 110 provides weather resistant, heavy-duty mechanism to convert foot motion into an electronic, electrical, or electrohydraulic system input over an extended life of operation. The Model 110 has proven itself as an industry leader in foot pedal technology, with decades of use in the field from high-end OEM companies. The housing is rugged cast aluminum material with adjustable mechanical stops, which provide an independent external control of the limits of travel. This unit mounts via a 4-bolt pattern, identical to hydraulic output foot controls made by the United States and European manufacturers for ease of interchangeability. The centering spring is a multi-coil high-cycle-life torsion spring, which provides the return force of the unit. The pivot is an oversized.75 inch diameter oil-impregnated bronze bushing, which further adds rigidity to the mechanism. MECHANICS: The Model 110 is now available with Hall Effect sensing, which eliminates any contact between moving electrical parts while further improving overall precision. Silicone dipping and potting further protects the electronics from direct exposure to the environmental corrosives. Gaskets seal both ends of the enclosure, and access openings allow for electrical adjustments on some models. The end cap provides six #6 screw terminals for electrical connection. A cap with electrical quick disconnect is also available. ELECTRONICS: Hall Effect (contactless) sensing is standard, which eliminates wear between moving electrical parts, improving reliability. Multiple output options are available in Hall Effect models. Also available are multiswitch (for 1, 2, or 3 incremental speeds), Potentiometric, and Pulse Width Modulated outputs (PWM, 22 watts). Valve drive boards are fully adjustable, including LO and HI output, ramp, and frequency (sold separately). Key Advantages: Contactless Hall Effect Technology Precise single-axis proportional control Totally enclosed weather-resistant construction EMI & RFI resistant Specifications: Electrical: Supply: Range 5-60 VDC (depending on electrical option) Output: Hall (typical): Max (+) Travel: 4.0 V DC Max (-) Travel: 1.0 V DC Centered: 2.5 VDC Output Impedance: 220 OHMS See electrical options page for further Hall Effect electrical options PWM (Pulse Width Modulated) 0-95% V in (both extremes adjustable) 22 watts maximum Switch Rating: 5A inductive to 15V 1.5 A inductive to 30V Potentiometric Rating: 2 Watts All inputs & outputs fully protected. Mechanical: Travel: Bidirectional ± 10 or ± 15 Unidirectional + 20 Operating Torque: Bidirectional 25-31 in-lbs. Unidirectional 25-37 in-lbs. Environmental: Temperature: - 40 to 85 C (- 40 to 185 F) Weather tight: sealed control packaging Electronics potted in epoxy.
MODEL 110 PART NUMBERING (Hall Effect Only) For special configurations, please call for assistance 110 S BD FT NC 56 Model 110 Foot Pedal Spring: S (Standard) H (Heavy) Ordering non-standard spring may increase lead time Mechanical Options: BD (Bi-Directional) UD (Uni-Directional) Electrical Option Case / Housing Option: NC (No Case) Mating connector sold separately. PQ#: A-09014-05 CS (Case w/ Strain Relief & Deutsch conn.) CT (Case w/ terminal block) Treadle Option: FT (Full Treadle) HT (Half Treadle) NT (No Treadle) Electrical Options: If you do not see your option listed, please call for assistance. Hydraulic valves require additional valve drive board. 56 = 10-30VDC, 2.5V NTRL ± 1.5V, 1.5 AMP DIR. AUX OUT 57 = 10-30VDC, 2.5V NTRL ± 1.25V, 1.5 AMP DIR. AUX OUT 58 = 5VDC, ± 30%, NO DIRECTIONAL AUX OUT 59 = 5VDC, ± 40%, NO DIRECTIONAL AUX OUT 60 = 18-60VDC, SEVCON, 1.5 AMP DIR. AUX OUT 61 = 10-30VDC, 2.5V NTRL ± 2.0V, 1.5 AMP DIR AUX OUT 62 = 10-30VDC, DANFOSS 63 = 10-30VDC, 0.0V NTRL + 10.0V, 1.5 AMP DIR AUX OUT 64 = 10-30VDC, 2.5V NTRL ± 1.5V, 1.5 AMP 50% DIR. AUX OUT 65 = 18-60VDC, PWR PAK SVCN, 0.2 AMP SINK DIR. AUX OUT 67 = 10-30VDC, 0.0V NTRL + 5.0V, 1.5 AMP DIR AUX OUT 68 = 10-30VDC, 2.5V NTRL ± 2.0V, 1.5 AMP 50% DIR. AUX OUT 69 = 5VDC, ± 10%, NO DIRECTIONAL AUX OUT 70 = 5VDC, ± 25%, NO DIRECTIONAL AUX OUT 71 = 10-30VDC, 4-20mADC (4mADC NTRL, 20mADC ends) 1.5 AMP DIR. AUX OUT 72 = 10-30VDC, 4-20mADC (12mADC NEUT, 4 and 20mADC ends) 1.5 AMP DIR. AUX OUT 73 = SPLIT SUPPLY INPUT (0vdc NEUT, POS. VS & NEG. VS @ ENDS) 15mAMP DIR. AUX OUT See the following pages for more details of electrical options (Options subject to change).