SPECIFICATION SilverStone 00W SFX Switching Power Supply FSP00-60GHS Meet 80 Plus Active PFC Circuit Full Range Input Small Size. GENERAL DESCRIPTION AND SCOPE This is the specification of Model UFSP00-60GHSU; AC-line powered switching power supply with active PFC (Power Factor Correction) circuit, meet EN6000-- and with Full Range Input features. The specification below is intended to describe as detailedly as possible the functions and performance of the subject power supply. Any comment or additional requirements to this specification from our customers will be highly appreciated and treated as a new target for usto approach.. REFERENCE DOCUMENTS The subject power supply will meet the EMI requirements and obtain main safety approvals as following:. EMI REGULATORY - FCC Part 5 Subpart J, Class B 5 Vac operation. - CISPR Class B 0 Vac operation. Copyright 009 SilverStone Technology Co., Ltd. All Rights Reserved
. SAFETY - NEMKO EN 60950 - TUV EN60950 OR VDE EN60950 - CSA-C. NO. 60950 - IEC 60950 - UL 60950 - CE : EN 550:998+A: 000, Class B EN 6000--: 000 EN 6000--: 995+A: 00 CISPR: 997+A: 000, Class B AS/NZS CISPR : 00, Class B. INPUT ELECTRICAL SPECIFICATIONS.. AC INPUT Parameter Min. Nom. () Max. Unit V in (5VAC) 90 5 5 VAC rms V in (0VAC) 80 0 65 VAC rms V in Frequency 7 -- 6 HZ Nominal voltages for test purposes are considered to be within.0v of nominal... INRUSH CURRENT Maximum inrush current from power-on (with power on at any point on the AC sine) and including, but not limited to, three line cycles, shall be limited to a level below the surge rating of the input line cord, AC switch if present, bridge rectifier, fuse, and EMI filter components. Repetitive ON/OFF cycling of the AC input voltage should not damage the power supply or cause the input fuse to blow. Copyright 009 SilverStone Technology Co., Ltd. All Rights Reserved
.. INPUT LINENT & POWER FACTOR (At Full load) AC input Input line current P.F.@ Full Load P.F.@ Pin=75W 5V <.5Amps rms > 0.95 >0.8 0V <.0Amps rms > 0.9 >0.75.. EFFICIENCY.. General Under the load conditions defined in Table and Table. The loading condition for testing efficiency shown in Table represents a fully loaded system. a ~ 50-60% (typical) loaded system.and a ~ 0-0% (light) loaded system. Table. Loading Table for Efficiency Measurement 00W (loading shown in Amps) Loading +V +V +5V +.V -V +5Vsb Full Typical Light 7.56.78.5 8.6..7.5 5.75. 0.6 5..09 0.7 0.8 0.07.8 0.9 0.7 Table. Minimum Efficiency Vs Load Full Typical Loading Voltage load load Minimum Efficiency for test purposes are considered to be within ±.0% of nominal. Light load Required Minimum Efficiency 5V 80% 8% 80% Required Minimum Efficiency 0V 80% 8% 80% Copyright 008 SilverStone Technology Co., Ltd. All Rights Reserved
.0. OUTPUT ELECTRICAL REQUIREMENTS. OUTPUT VOLTAGE AND CURRENT RATING Output MINIMUM NORMAL MAXIMUM PEAK LOAD LINE RIPPLE LOAD LOAD LOAD LOAD REG REG. & NOISE +.V 0.5A 0A - 5% % 70mV P-P +5V 0.5A A - 5% % 70mV P-P +VDC.0A A 9A 5% % 0mV P-P +VDC.0A 6A 9A 5% % 0mV P-P -V 0.0A 0.5A - 0% % 0mV P-P +5VSB 0.0A.5A.5A 5% % 70mV P-P ( ) +.V & 5V total output not exceed 5W. ( )Total output continuous shall not exceed 00W watts. ( )+V Peak current is 9A(less then 0m Sec.),minimum voltage during peak is >0.8Vdc. ( )5Vsb Peak current is A(less then 500m Sec.), minimum voltage during peak is >.5Vdc. ( 5 )maximum combined current for the V outputs shall be A. Voltages and ripple are measured at the load side of mating connectors with a 0. uf monolithic ceramic capacitor paralleled by a 0 uf electrolytic capacitor across the measuring terminals... LOAD CAPACITY SPECIFICATIONS The cross regulation defined as follows, the voltage regulation limits DC include DC Output ripple & noise. LOAD +.V +5V +V DC +V DC -V +5VSB Condition_ X X X X X.5A Condition_ 0.5A 0.5A A A 0A 0A Condition_ 0.5A 0.5A A A 0.5A 0A Condition_ 0.5A 5A A 6A 0.A 0.A Condition_5 A A A A 0.A 0.A Condition_6 A A A A 0.A 0.A Condition_7.5A A 6.7A 6.7A 0.A A Condition_8 8A A A A 0A 0.A Condition_9 0A.8A 6.7A 6.7A 0.A A.. HOLD-UP TIME (@FULL LOAD) 5V / 60Hz : 7 msec. Minimum. 0V / 50Hz : 7mSec. Minimum. The output voltage will remain within specification, in the event that the input power is removed or interrupted, for the duration of one cycle of the input frequency. The interruption may occur at any point in the AC voltage cycle. The power good signal shall remain high during this test. Copyright 008 SilverStone Technology Co., Ltd. All Rights Reserved
..OUTPUT RISE TIME (0% TO 95% OF FINAL OUTPUT VALUE, @FULL LOAD) 5V-rms or 0V-rms +.Vdc : 0ms Maximum + 5Vdc : 0ms Maximum + Vdc : 0ms Maximum + 5Vsb : 5ms Maximum - Vdc : 0ms Maximum.5.OVER VOLTAGE PROTECTION Voltage Source Protection Point +.V.76V-.5V +5V 5.6V-7.0V +V.0V-6.5V.6.OVER-CURRENT PROTECTION OUTPUT VOLTAGE Max. overcurrent limit +.V 60A +5V 8A +V DC 5A +V DC 0A.7.SHORT CIRCUIT PROTECTION Output short circuit is defined to be a short circuit load of less than 0. ohm. In the event of an output short circuit condition on +.V, +5V or +V output, the power supply will shutdown and latch off without damage to the power supply. The power supply shall return to normal operation after the short circuit has been removed and the power switch has been turned off for no more than seconds..8. POWER SIGNAL POWER GOOD @ 5/0V,FULL LOAD POWER FAIL @5/0V, FULL LOAD 00 500mSec. msec. minimum 5 Copyright 009 SilverStone Technology Co., Ltd. All Rights Reserved
5.0 FAN NOISE REQUIREMENTS 5..The subject power supply is cooled by a self-contained, 80mm 5mm, VDC fan 6.0 ENVIRONMENTAL REQUIREMENTS The power supply will be compliant with each item in this specification for the following Environmental conditions. 6.. TEMPERATURE RANGE Operating +0 to +50 deg. C Storage -0 to +80 deg. C The maximum continuous power rating of supply is 00W at 50? 6.. HUMIDITY Operating Storage 5 95% RH, Non-condensing 5 95% RH, Non-condensing 6.. VIBRATION TThe subject power supply will withstand the following imposed conditions without experiencing non-recoverable failure or deviation from specified output characteristics. Vibration Operating Sine wave excited, 0.5 G maximum acceleration, 0-50 Hz swept at one octave / min. Fifteen minute dwell at all resonant points, where resonance is defined as those exciting frequencies at which the device under test experiences excursions two times large than non-resonant excursions. Plane of vibration to be along three mutually perpendicular axes. 6.. GROUND LEAKAGE CURRENT The power supply groud leakage current shall be less than.5 ma. 6.5. RELIABILITY The power supply reliability,when calculated by MIL-HDBK-7;latest revision, are exceed 00,000 hours with all output at maximum load and an ambient temperature of 5?. 6.6. DIELECTRIC STRENGTH Primary to Frame Ground : 800 Vac for sec. Primary to Secondary : 800Vac for sec 6.7. INSULATION RESISTANCE Primary to Frame Ground : 0 Meg.ohms Minimum 6 Primary to Secondary : 0 Meg.ohms Minimum Copyright 009 SilverStone Technology Co., Ltd. All Rights Reserved
7. LABELLING Label marking will be permanent, legible and complied with all agency requirements. 7.. MODEL NUMBER LABEL Labels will be affixed to the sides of the power supply showing the following: - Manufacturer s name and logo. - Model no., serial no., revision level, location of manufacturer. - The total power output and the maximum load for each output. - AC input rating. 8.0. MECHANICAL SPECIFICATIONS 8. Physical Dimension 5 mm (W) 6.5 mm (H) 00 mm (D) 8. Connectors Define Blue Green White Signal Pin Pin Signal +.V +.V +.Vsense -VDC +.V 5 PS-ON 6 7 5 8 6 9 7 N/C 0 8 PWRGOOD 9 +5Vsb 0 +V +5Vsense +V +.V Grey Purple ATX V PIN(+PIN EPS V in split mode) Signal Pin Pin Signal GND +V GND +V 7 Copyright 009 SilverStone Technology Co., Ltd. All Rights Reserved
8. Connectors Define Signal Pin Pin Signal +V +V SATA connector Signal +.V +5V +V Pin 5 6PIN PCI Express connector Signal Pin Pin Signal +V +V 5 +V 6 8 Copyright 009 SilverStone Technology Co., Ltd. All Rights Reserved