Product catalogue 2018/1 Solar mounting components
Table of contents Roof hooks Page 2 Fasteners for trapezoidal and corrugated roofing Page Clamps Page 13 Profiles Page 14 Connecting elements Page 17 Accessories for profiles and connectors Page 18 Elevation angles Page 18 Module mounting parts Page 20 Mounting accessories Page 25 Free of cost sample-ordering Page 28 Overview mounting systems Page 2 Certifi ed to EN 10 0-1:2000 +A1 :2011
Your contact persons Markus Stehle and Katja Pasold Managing directors Detlef Penzel Sales force Phone +4 151 55001321 d.penzel@ altec-metalltechnik.de Annelie Steinmark Sales mounting systems Phone +4 3663 4210-224 a.steinmark@ altec-metalltechnik.de Kristin Eichler Sales mounting systems Phone +4 3663 4210-234 k.eichler@ altec-metalltechnik.de Doreen Schilling Sales mounting systems Phone +4 3663 4210-225 d.schilling@ altec-metalltechnik.de Katja Wisotzki Sales solar components Phone +4 3663 4210-200 k.wisotzki@ altec-metalltechnik.de Ines Görler I am on parental leave and will soon be back! Building approval DIBt Z-1-14. 4.4-4- 65 8 issued comp mpli lian t componen ents
Shingle roof hook Shingle- and slate roof hooks are screwed through the formwork upon the rafter. Two 6 80 mm sunk woodscrews are required to attach the short shingle roof hooks, for long slate roof hooks you need three. After mounting a careful sealing of the roof hook is necessary. For slate covering you need a cover plate in addition. This plate replaces the slate at the location of the roof hook. Shingle roof hook Material: 6 mm stainless steel 1.4301; hole 7 sunk For use with full-thread woodscrew for wood connection as of Z-.1-72 Shingle roof hook height adjustable Material: 6 mm stainless steel 1.4301; hole 7 sunk For use with full-thread woodscrew for wood connection as of Z-.1-72 65 0 135 141 d 70 d 70 5 d Slot 15S003068000 30 15S003568000 35 15S003561000 11 15S004068000 40 15S004061000 11 d Slot 15S003568H00 35 15S003561H00 11 15S004068H00 40 15S004061H00 11 Roof mounting parts 2
Slate roof hook Shingle- and slate roof hooks are screwed through the formwork upon the rafter. Two 6 80 mm sunk woodscrews are required to attach the short shingle roof hooks, for long slate roof hooks you need three. After mounting a careful sealing of the roof hook is necessary. For slate covering you need a cover plate in addition. This plate replaces the slate at the location of the roof hook. Slate roof hook Material: 6 mm stainless steel 1.4301; hole 7 sunk For use with full-thread woodscrew for wood connection as of Z-.1-72 Slate roof hook height adjustable Material: 6 mm stainless steel 1.4301; hole 7 sunk For use with full-thread woodscrew for wood connection as of Z-.1-72 d d 65 0 250 256 70 70 5 d Slot 15S103068000 30 15S103568000 35 15S103561000 11 15S104068000 40 15S104061000 11 d Slot 15S103568H00 35 15S103561H00 11 15S104068H00 40 15S104061H00 11 You need slate roof hooks with your specifications? We create you an offer! Name E-Mail Phone a = b = c = f = Slot Slot 11 height adjustable Quantity Roof mounting parts +4 3663 4210-211 info@altec-metalltechnik.de 3
Plain tile roof hook without base plate Plain tile roof hooks for roofs with plain tile covering are screwed directly upon the rafter with two flat head screws. Since the lengthwise protruding bracket of the plain tile roof hooks rests on the tiles beneath, we recommend replacing the clay tile with a metal tile. Please contact us with regard to crown tiles so that we can match the material to the roofing. To avoid edge pressure it is recommended to use EPDM-strips 40 3 ( 5EPDM0403010) where the roof hooks hit. Plain tile roof hook without base plate Material: 6 mm stainless steel 1.4301; hole, for use with flat head screw with countersunk slit (approv. no. Z-.1-453) Plain tile roof hook without base plate, height adjustable Material: 6 mm stainless steel 1.4301; hole, for use with flat head screw with countersunk slit (approv. no. Z-.1-453) d 32 32 105 0 21 21 320 326 d 120 120 145 d Slot 15B003568000 35 15B004068000 40 d Slot 15B003568H00 35 15B004068H00 40 You need plain tile roof hooks with your specifications? We create you an offer! Roof mounting parts a = b = c = d = e = f = Name E-Mail Phone with base plate: 150 80, Holes 150 80, Holes 7 150 60, Holes 180 80, Holes Slot Slot 11 height adjustable Quantity 4 +4 3663 4210-211 info@altec-metalltechnik.de
Plain tile roof hook with base plate Plain tile roof hooks for roofs with plain tile covering are screwed directly upon the rafter with two flat head screws. Since the lengthwise protruding bracket of the plain tile roof hooks rests on the tiles beneath, we recommend replacing the clay tile with a metal tile. Please contact us with regard to crown tiles so that we can match the material to the roofing. To avoid edge pressure it is recommended to use EPDM-strips 40 3 ( 5EPDM0403010) where the roof hooks hit. Plain tile roof hook with base plate Material bracket: 6 mm stainless steel 1.4301 Material base plate: 4 mm stainless steel 1.4016, 2 6 holes For use with flat head screw with countersunk slit (approval no. Z-.1-453) Plain tile roof hook with base plate, height adjustable Material bracket: 6 mm stainless steel 1.4301 Material base plate: 4 mm stainless steel 1.4016, 2 6 holes For use with flat head screw with countersunk slit (approval no. Z-.1-453) 150 150 105 218 301 80 32 0 218 307 80 32 d 120 d 120 145 d Slot 12B013568000 35 12B013561000 11 12B014068000 40 12B014061000 11 d Slot 12B013568H00 35 12B013561H00 11 12B014068H00 40 12B014061H00 11 Roof mounting parts 5
Pantile roof hook Pantile roof hooks have been especially designed for use on pantile roofs and are screwed directly onto the rafters. If the batten is higher than 30 mm we recommended using a rafter shim and longer flat head screw. Pantile roof hook Material bracket: 6 mm stainless steel 1.4301 Material base plate: 4 mm stainless steel 1.4016, 2 6 holes For use with flat head screw with countersunk slit (approval no. Z-.1-453) Pantile roof hook height adjustable Material bracket: 6 mm stainless steel 1.4301 Material base plate: 4 mm stainless steel 1.4016, 2 6 holes For use with flat head screw with countersunk slit (approval no. Z-.1-453) 150 150 80 187 45 12 45 85 0 104 104 80 d 130 d 130 155 d Slot 12P113568000 35 12P113561000 11 12P114068000 40 12P114061000 11 d Slot 12P113568H00 35 12P113561H00 11 12P114068H00 40 12P114061H00 11 You need pantile roof hooks with your specifications? We create you an offer! Roof mounting parts a = b = c = d = e = f = g = Name E-Mail Phone with base plate: 150 80, holes 150 80, holes 7 150 60, holes 180 80, holes Slot Slot 11 height adjustable Quantity 6 +4 3663 4210-211 info@altec-metalltechnik.de
Pantile roof hooks for special requirements Pantile roof hook for higher static load Material bracket: 8 mm stainless steel 1.4301 Material base plate: 4 mm stainless steel 1.4016, 2 6 holes For use with flat head screw with countersunk slit (approval no. Z-.1-453) Pantile roof hook Double height adjustable Material bracket: 6 mm stainless steel 1.4301 Material base plate: 4 mm stainless steel 1.4016, 2 6 holes For use with flat head screw with countersunk slit (approval no. Z-.1-453) 150 135 80 18 45 203 33 54 0 0 102 105 80 40 130 d 122 163 12P114081000 d 22236580H000 35 22236280H000 40 Roof mounting parts 7
Accessories for roof hooks Cover plate for slate roof hooks Material: aluminium 0.8 mm Other dimensions on request! For use with two screws ( 4ASIV0204025) We recommend to apply an expansion strip between the plate and the slate. Metal tile for plain tile Material: aluminium 0.8 mm Other dimensions on request! The metal tile for plain tile covering prevents the lower tile being crushed by the load. Because the clay tile does not need to be cut out, installation is greatly simplified. The metal tile is cut to standard size and is fixed to the rafter with two screws (item no: 4ASIV0204025). Alternatively, with crow tiles, it is hung to the tile beneath. We recommend to apply an expansion strip between the plate and the slate. Measures 1123100230 1.000 230 Measures 1123200181 360 180 Rafter slim 80 80 mm; Material: wood Differences in height created by uneven battens or roof warping can be resolved by using rafter shims. Compensating sheave 40 50 mm; Material: aluminium If height differences are present, these allow for better and even rail positioning. Thickness 120808005000 5 120808010000 10 120808015000 15 Thickness Slot 113040501800 1 113040502800 2 113040503800 3 113040505800 5 113040501100 1 113040502100 2 11 113040503100 3 113040505100 5 Roof mounting parts 8 Expanding water stop reel Expanding water stop is used as a water proofing seal, for example with metal tiles on roof or with plain tile roofing as a seal on the transition to the roofing. 5QB04015080 Measures Thickness 4 ; reel = 8 m
Trapezoidal roof mounting parts ALTEC SD_TRAFIX-H Material: aluminium, EN AW-6063 T66; pierced; with EPDM tape laminated; delivery includes 2 thin metal screws ALTEC SD_TRAFIX-V-SELECT Material: aluminium, EN AW-6063 T66; pierced; with EPDM tape laminated; delivery includes 4 thin metal screws NEW 1TCB28220164 1TVE17737500 for ledge spacing 177, 183, 10, 207, 214, 250, 275, 280, 305, 310, 315, 333, 350, 375 ALTEC SD_TRAFIX-V Material: stainless steel 1.4301 (trapezoidal sheet fastener); A2-70 (thin metal screws); aluminium (profile); black plastic (end caps) EPDM tape close cell, glue on one side only, reel Description Measures Thickness 1TF5000102 1TF5000204 1TF5000205 single sheet fastener Two sheet fasteners with 450 mm profile 40 40 standard and 4 thin metal screws 6.0 25 as TF5000204, with end caps 5EPDM0303010 30 10.000 5EPDM0403010 40 10.000 5EPDM1002020 100 20.000 5EPDM1202020 120 20.000 3 2 5EPDM1203020 120 20.000 3 NEW EPDM tape close cell, glue on one side only, strip Measures Thickness 1EPDM1001002 100 100 1EPDM1001202 100 120 2 1EPDM1101002 110 100 Roof mounting parts
For this check list as download and further check lists please visit www.altec-metalltechnik.de/en/downloads Check list for trapezoidal metal shoe Enquiry Order (mark with a cross where applicable) +4 3663 4210-211 +4 3663 4210-0 info@ altec-metalltechnik.de Name: No./address: Post code/town: Telephone: Fax: E-mail: Number of units*: Delivery date: *In the case of trapezoidal metal shoes a quantity deviation of approx. + 1 % and/or 1 unit) of the total quantity is possible. with plate with angled bar with bar with welded bolt Slot: M8 M10 Slot: M8 M10 Slot: M8 M10 Threaded bolt: M8 M10 Accessories With drilling screws: yes no with EPDM tape: cutted linear meters Sizes Please measure the seams of the corrugation so that we can calculate an individual o er for you. We can supply you with 2 mm thick EPDM strip for the trapezoidal shoe at an additional cost. c a d a: mm b: mm c: mm d: mm Roof mounting parts f Material of corrugated sheet: b f: mm 10 Place/date: Company stamp/signature:
Trapezoidal shoes custom made product Trapezoidal shoes with different attachments will be especially produced for the needed crown widths. This helps to ensure optimal fit and leak on the roof. The choices are three different attachments: Bridge, angle or threaded bolts. Due to the bearing surfaces of the trapezoidal shoe can ensure optimal power transfer to the roof. It is among other things very well suited as a basis for an elevated trapezoidal roof mounting. It is supplied with EPDM-sealing tape. Please use our checklist for trapezoidal shoes! Trapezoidal shoe with plate Trapezoidal shoe with welded bolt on request Description with bolt M8 or M10 60 Top width 25 30 mm 31 45 mm 45 60 mm Trapezoidal shoe with angled bar Trapezoidal shoe with bar Description Slot Top width Angle 30 6 25 30 mm Angle 35 6 11 25 30 mm Angle 30 6 31 45 mm Angle 35 6 11 31 45 mm Angle 30 6 45 60 mm Angle 35 6 11 45 60 mm Description Slot Top width Bar 30 6 25 30 mm Bar 35 6 11 25 30 mm Bar 30 6 31 45 mm Bar 35 6 11 31 45 mm Bar 30 6 45 60 mm Bar 35 6 11 45 60 mm Roof mounting parts 11
Trapezoidal/corrugated roof mounting parts Hanger bolt with locking nuts and EPDM-sealing washer Material: stainless steel 1.4301 Hanger bolts or dowel screws with wood thread (lower) and machine thread (upper). They are delivered pre-assembled with an EPDM sealing washer, securing nuts and two locking nuts. Adapter plate for hanger bolts or threaded rod fastenings Material: stainless steel 1.4301 Adapter plates are used as connecting elements between hanger bolts or threaded rods and profile rails. Rails are fastened with hammer head screws via the slot and can be positioned this way. The round hole is used to fasten the adapter to the hanger bolt. with calotte/storm calotte on request Measures Hexagon bolt 11200102000 M10 200 SW7 4112M2122500 M12 250 SW Measures Hanger bolt Mounting screw 15AB03568100 35 6 80 M10 M8 15AB04068200 40 6 85 M12 M8 15AB04061200 40 6 85 M12 M10 15AB04081200 40 8 85 M12 M10 Solar fastener for wave profile or trapezoidal sheet with self-tapping thread Material: stainless steel 1.4301 The solar fastener can be used in steel girders with a thickness of 1.5 to 10 mm. Depending on the material, pre-drilling before assembly may be required. Roof mounting parts Threaded upper section Length M10 50 or M10 70 100, 125, 150, 200 12
Clamps for folding roofs For all clamps you must ensure that the first profile rail runs transverse to the felt. If required, install a cross connector. For a save mounting it is recommended checking of the connection between roofing surface and roof construction through experts. Standing seam clamp Material: stainless steel 1.4301 Standing seam clamp Material: stainless steel 1.4301 Hole Clamping range 115451108110 3.5 115451110110 11 Hole Clamping range 115451008020 3.5 115451010020 11 215451008510 5 215451010510 11 Rolled top standing seam clamp Material: stainless steel 1.4301 Folded sheet metal clamp (RIB-ROOF) Material: stainless steel 1.4301 Hole 115452008020 115452010020 11 Hole Used for 115453108410 RIB-ROOF 465 115453110410 11 115453108510 RIB-ROOF 500 115453110510 11 Custom solutions for other seam roofs You have a very special seamed roof but no suitable clamping? Our experienced team will develop your special solution. Please let us have a sample of the seamed roof together with your enquiry and we will reach a tight fit. Roof mounting parts 13
Profiles Material: aluminium, EN AW-6063 T66 Channel width 11; slot width 22.4 to accept hammer-head screws Length over 6,000 mm on request. Additional standard rail length We are now supplying a new standard length for our 28 28, 33 38, 40 40 light and standard profiles: 5200 mm. Saving This length fits perfectly with current module widths of one metre. You will save on the cost of materials and don t need to cut rails to size on site. We have also priced in a saving for you on this rail length it s worth comparing! We can make you an offer at a comparable price to the standard 6-metre rails. Profile 68 15 Profile 28 22 Length Weight 630P06815060 6,000 130P06815000 cut to required length 0.477 kg/m (up to 6,000) Length Weight 630P02822061 6.000 130P02822001 cut to required length 0,602 kg/m (up to 6,000) Profile 28 28 Profile 38 33 Profiles and connectors 14 Length Weight 630P02828061 6,000 630P02828052 5,200 130P02828001 NEW cut to required length (up to 6,000) 0.75 kg/m Length Weight 630P03833060 6,000 630P03833052 5,200 130P03833000 NEW cut to required length (up to 6,000) 0.745 kg/m
Profiles Material: aluminium, EN AW-6063 T66 Channel width 11; slot width 22.4 to accept hammer-head screws Length over 6,000 mm on request. Profile 40 40 light Profile 40 40 standard Length Weight 630P04040L61 6,000 630P04040L52 5,200 NEW 630P04040L41 4,500 130P04040L01 cut to required length (up to 6,000) 0.66 kg/m Length Weight 630P04040S60 6,000 630P04040S52 5,200 NEW 630P04040S40 4,500 130P04040S00 cut to required length (up to 6,000) 1.074 kg/m Profile 40 40 standard, black anodised Profile 40 60 Length Weight 63EP04040S60 6,000 13EP04040S00 cut to required length 1.074 kg/m (up to 6,000) Length Weight 630P04060060 6,000 130P04060000 cut to required length 1.454 kg/m (up to 6,000) Profiles and connectors 15
Profiles Material: aluminium L-Profile T-Profile Measures Length Weight 630W30303C 30 30 3 0.462 kg/m 630W40404C 40 40 4 0.821 kg/m 6,000 630W50504C 50 50 4 1.037 kg/m 630W50505C 50 50 5 1.283 kg/m Measures Length Weight 630T60804C 60 80 4 6,000 1.46 kg/m Special profiles and connectors on request Material: aluminium, EN AW-6063 T66 Profile 45 75 Connector/Expansion connector for profile 45 75 Connector includes 8, expansion connector includes 4 drilling screws JT3-6-5,5 25, without sealing washer Profile 65 100 Minimum order 1 t = 360 m Profile 75 120 Minimum order 1 t = 280 m Profiles and connectors 16
Connecting elements Cross connector Material: aluminium, EN AW-6063 T66 Attachment of 38 33, 40 40 Standard, 40 60, 65 100 and 75 120 profile rails to other profiles (cross connection) Profile connector 4-hole Material: stainless steel 1.4301 for profiles 28 28, 38 33, 40 40 light and standard The profile connectors are delivered completely pre-assembled with hammer head bolts and locking nuts. pre-assembled with Measures/Description 1101003K000 Cylinder head screw M6 16, threaded plate 11501441K020 30 6 200 for rail connection outside of the centre of moments 1101001K000 Hammer head screw M8 20, hex nut, washer 11501441K120 30 4 200 for rail connection at the centre of moments 1101004K000 Hexagon head screw M6 16, threaded plate, washer L-angle Material: stainless steel 1.4301 pre-assembled with 2 hammer head screws and locking nuts Expansion connector Material: aluminium, EN AW-6063 T66 Measures 115070404K30 30 4 1130111K0010 for profiles 28 28, 38 33, 40 40 light and standard, 40 60 Z-angle Material: stainless steel 1.4301 pre-assembled with 2 hammer head screws and locking nuts Measures 115060284K10 30 4 28 Profiles and connectors 17
Accessories for profiles and connectors Edge clip Material: polyamid 6.6, UV stabilised Cable tie Material: polyamid 6.6, UV stabilised 5KANSW482003 5KANSW482005 Used for parallel to edge transverse to edge Measures 5UNISW483000 4,8 20 300 End cap for profile rails Material: black plastic Lightning protection Measures 118000282800 28 28 118000383300 38 33 118000404000 40 40 118000604000 40 60 113036080100 Elevation angles Elevation angles from the ALTEC Metalltechnik GmbH range are manufactured specifically for your particular project. Therefore, it is necessary that we receive your required module installation angle and existing roof slope. We also machine the base fixing holes in order to position the holes precisely please complete the check list. All parts are delivered unassembled and then simply bolted together on site. Pre-assembled and welded angles can be supplied for a surcharge. The size and design of the elevation angle should always consider the local conditions and load requirements. Please use our check list for elevation angles! Profiles and connectors 18
For this check list as download and further check lists please visit www.altec-metalltechnik.de/en/downloads Check list for elevation angles Enquiry Order (mark with a cross where applicable) +4 3663 4210-211 +4 3663 4210-0 info@ altec-metalltechnik.de Name: No./address: Post code/town: Telephone: Mobile phone: Fax: E-mail: Units required: Elevation normal a Distance between contact points b Lower edge of angle to lower edge of module mm mm a α c b c Distance between angles mm Elevation angles Number of diagonal struts units multiple a Distance between contact points a 1 Distance between contact points mm mm b Lower edge of angle to lower edge of module mm a α c b c Distance between angles mm Elevation angle Number of diagonal struts units Modules Module size: Length: mm Width: mm Height: mm Weight: kg Module arrangement: vertical horizontal Do you require a structural stability analysis? yes no Profiles and connectors 1
Clamping plates Clamping plate for use in smallest possible module spacing (7 mm), hole for screw M8 on request Plate size 50 26 4, Material: aluminium, EN AW-6063 T66 Clamping plate unmounted Clamping plate unmounted, black anodised for screw 313030264600 M6 313E30264600 for screw M6 Clamping plate with hexagon bolt Delivery includes threaded plate M6, hexagon bolt and washer Other module heights available on request. Clamping plate with hexagon bolt, black anodised Delivery includes threaded plate M6, hexagon bolt and washer Other module heights available on request. Module height Screw 113030284600 28 32 M6 45 113030334600 33 37 M6 50 113030384600 38 42 M6 55 113030434600 43 47 M6 60 113030484600 48 50 M6 65 Module height Screw 113E30284600 28 32 M6 45 113E30334600 33 37 M6 50 113E30384600 38 42 M6 55 113E30434600 43 47 M6 60 113E30484600 48 50 M6 65 Module mounting parts 20
Mid-clamps Module space 1 mm, Clamp length 70 mm, hole for screw M8 on request Material: aluminium, EN AW-6063 T66 Mid-clamp unmounted Mid-clamp unmounted, black anodised for screw 31030700600 M6 31E30700600 for screw M6 Mid-clamp with cylinder head screw Delivery includes threaded plate M6 and cylinder head crew Other module heights available on request. Mid-clamp with cylinder head screw, black anodised Delivery includes threaded plate M6 and cylinder head crew Other module heights available on request. Module height Screw 11032300600 30 33 M6 20 11032340600 34 38 M6 25 1103230600 3 43 M6 30 11032440600 44 48 M6 35 1103240600 4 50 M6 40 Module height Screw 11E32300600 30 33 M6 20 11E32340600 34 38 M6 25 11E3230600 3 43 M6 30 11E32440600 44 48 M6 35 11E3240600 4 50 M6 40 Module mounting parts 21
End-clamps Clamp length: 40 mm (individual length and other module heights on request) Material: aluminium, EN AW-6063 T66 hole for screw M8 on request End-clamp with bar without bar Module height Type unmounted with cylinder head screw with hexagon bolt 31 with bar 31020310600 11022310600 11020310600 33 with bar 31020330600 11022330600 11020330600 35 without bar 31020350600 11022350600 11020350600 38 without bar 31020380610 11022380610 11020380610 3 with bar 3102030600 1102230600 1102030600 40 without bar 31020400600 11022400600 11020400600 41 with bar 31020410600 11022410600 11020410600 42 without bar 31020420600 11022420600 11020420600 45 without bar 31020450600 11022450600 11020450600 46 with bar 31020460610 11022460610 11020460610 50 without bar 31020500600 11022500600 11020500600 End-clamp black anodised with bar without bar Module height Type unmounted with cylinder head screw with hexagon bolt Module mounting parts 22 31 with bar 31E20310600 11E22310600 11E20310600 33 with bar 31E20330600 11E22330600 11E20330600 35 without bar 31E20350600 11E22350600 11E20350600 38 without bar 31E20380610 11E22380610 11E20380610 3 with bar 31E2030600 11E2230600 11E2030600 40 without bar 31E20400600 11E22400600 11E20400600 41 with bar 31E20410600 11E22410600 11E20410600 42 without bar 31E20420600 11E22420600 11E20420600 45 without bar 31E20450600 11E22450600 11E20450600 46 with bar 31E20460610 11E22460610 11E20460610 50 without bar 31E20500600 11E22500600 11E20500600
Slip protection Slip protection end-clamp Slip protection cylinder head screw Material: A2, for mounting hole 6 mm with cylinder head screw with hexagon bolt Module height 11053310600 11050310600 31 11053330600 11050330600 33 11053350600 11050350600 35 11053380610 11050380610 38 1105330600 1105030600 3 11053400600 11050400600 40 11053410600 11050410600 41 11053420600 11050420600 42 11053450600 11050450600 45 11053460610 11050460610 46 11053500600 11050500600 50 Screw 10120206010 M6 10 Slip protection end-clamp, black anodised mit Zylinderkopfschraube with hexagon bolt Module height 11E53310600 11E50310600 31 11E53330600 11E50330600 33 11E53350600 11E50350600 35 11E53380610 11E50380610 38 11E5330600 11E5030600 3 11E53400600 11E50400600 40 11E53410600 11E50410600 41 11E53420600 11E50420600 42 11E53450600 11E50450600 45 11E53460610 11E50460610 46 11E53500600 11E50500600 50 Module mounting parts 23
Universal clamps Universal mid-clamp Material: aluminium, EN AW-6063 T66 Clamp length: 70 mm, module space 1 mm Delivery includes snap fit block M6 and cylinder head screw M6 25. Other module heights available on request. Universal mid-clamp black anodised Material: aluminium, EN AW-6063 T66 Clamp length: 70 mm, module space 1 mm Delivery includes snap fit block M6 and cylinder head screw M6 25. Other module heights available on request. Module height 11038350600 35 50 Module height 11E38350600 35 50 Universal end-clamp Material: aluminium, EN AW-6063 T66 Clamp length: 70 mm. Delivery includes snap fit block M6 and cylinder head screw M6 40 resp. 45. Universal end-clamp black anodised Material: aluminium, EN AW-6063 T66 Clamp length: 70 mm. Delivery includes snap fit block M6 and cylinder head screw M6 40 resp. 45. Module height 11028350600 35 46 11028400600 40 50 Module height 11E28350600 35 46 11E28400600 40 50 Universal module clamping for horizontally, elevated module mounting set Material: aluminium, EN AW-6063 T66 Material: aluminium, EN AW-6063 T66 Material: stainless steel 1.4301 Module mounting parts Clamp Anti-slide protection Slip protection Modulhöhe Screw 11021000800 25 50 113056404810 M8 20 115051000000 24
Mounting accessories Hammer head screw Material: A2-70, General building approval Z-14.4-658 Locking nut DIN 623 Material: A2-70 Size 40HKS0208020 M8 20 40HKS0208030 M8 30 40HKS0208040 M8 40 40HKS0210030 M10 30 Size 46230208000 M8 46230210000 M10 46230212000 M12 Hexagon nut DIN 34 (EN ISO 4032) Material: A2-70 Threaded plate Material: A2, General building approval Z-14.4-658 Size 40340206000 M6 40340208000 M8 40340210000 M10 40340212000 M12 40GP00206001 for screw M6 System mat with fixing flaps foil-laminated Upper side with fixing flaps, the bottom side (foil-laminated) prevents the migration of plasticizers between roof cladding and building protection mat 5BSMA0401206 Measures 400 120 6mm Mounting accessories 25
Mounting accessories Hexagon bolt M6 DIN 33 (EN ISO 4017) Material: A2-70 Hexagon bolt M8 DIN 33 (EN ISO 4017) Material: A2-70 6 11,05 8 14,38 4 Length 10 5,3 Length 13 Length 40330206045 45 40330206050 50 40330206055 55 40330206060 60 40330206065 65 Length 40330208016 16 40330208020 20 40330208025 25 40330208035 35 40330208040 40 Thin metal screw self-tapping Material: A2-70, general building approval Z-14.1-537, Z-14.1-4 Drilling screw Ruspert -Covering Material: A2-70 general building approval Z-14.1-537, Z-14.1-4 d l 4BSRP0206025 6.0 25 d l 42062206325 6.3 25 Cylinder head screw with hexagon socket DIN 12 (EN ISO 4762) Material: A2-70 Torx head countsunk wood screw with internal serration fully threaded Material: A2-70 general building approval Z-.1-72 Mounting accessories d l 40120206010 6 10 40120206025 6 25 40120208016 8 16 40120208030 8 30 d l 4ASIV0206080 6 80 26
Mounting accessories Flat head screw with countsunk slit Material: A2-70 general building approval Z-.1-453 Hexagon head wood screw M8 DIN 571 Material: A2-70 dk d 8 14,2 l 5,5 0,6l Length 13 d l dk Length 4TKIT206100 6 100 14 4TKIT208100 8 100 17,5 405710208080 80 405710208100 100 Washer DIN 125 (EN ISO 708) Material: A2-70 Washer DIN 021 (EN ISO 703) Material: A2-70 Size Size 401250206400 for M6 401250208400 for M8 401250210500 for M10 401250213000 for M12 40210206400 for M6 40210208400 for M8 40210210500 for M10 40210213000 for M12 Mounting accessories 27
Free samples You are welcome to configure your own sample set based on the individual components in this catalog. Request of samples is free of charge. Sample for pitched roof system MUSDM01 Contains: 1 shingle roof hook, 1 pantile roof hook, 1 profile 40 40 standard, 1 profile 38 33, 1 end cap für profile 40 40, 1 cross-connector, 1 end-clamp, 1 mid-clamp, 1 slip protection end-clamp, 1 hammer head screw, 1 locking nut with serrated flange Sample for pitched roof system black anodised MUSDME01 Contains: 1 profile 40 40 standard, 1 end-clamp, 1 mid-clamp, 1 slip protection end-clamp Free of cost sample-ordering 28 Sample for trapezoidal roof mounting MUTDM01 Contains: 1 ALTEC SD_TRAFIX-V-SELECT, 1 ALTEC SD_TRAFIX-V, 1 ALTEC SD_TRAFIX-H
ALTEC SD_ON-ROOF Pitched roof system on-roof mouting Select the roof mounting parts in accordance to your roof cladding: Roof hooks for numerous kinds of roof covering (shingle, slate, plain tile or pantile) Hanger bolts and solar fasteners are used for roofs with corrugated sheeting Subsequently the profile rails will be mounted (vertically or horizontally) Vertical module mounting After assembling of the mounting rails on the roof mounting parts the module will be fitted on them. Vertical mounting on tiles and corrugated roofs Horizontal module mounting (cross connection) The profiles will be assembled on the roof mounting parts. The mounting rails will be fixed on the profiles by using cross-connectors. Select from our range of clamps the most optimal component. There are module clamping angles or alternatively end-clamps and clamping plates or alternatively midclamps. Horizontal mounting (cross connection) on tiles, seamed and corrugated roofs Our Check list mounting system can be found at www.altec-metalltechnik.de/en/downloads/ Overview mounting systems 2
ALTEC SD_TRAFIX Trapezoidal roof-mounting ALTEC SD_TRAFIX-H (for horizontal module installation) Use therefore our trapezoidalc-profile connector, which only consists of four parts: One piece cut c-profile (pre-drilled and with EPDM tape covered), one piece of midclamp and end-clamp as well as two thin metal screws. No pre-drilling necessary. ALTEC SD_TRAFIX-V (for vertical module installation) Universal using of our trapezoidal mounting system on almost all trapezoidal metal roof covering. It guarantees an easy and fast mounting, less material necessary. Overview mounting systems Overview mounting systems NEW ALTEC SD_TRAFIX-V-SELECT (for vertical module installation) For urgent projects on trapezoidal roofs with module installed vertical, this mounting system means you can work cost-effectively and flexibly. You can mount every module width with ease, because you can choose to position the solar modules at any point on the rail. 30
ALTEC SD_VARIO Pitched roof systems elevated assemblies If the roof isnʼt sloped enough, the modules can be elevated by our mounting systems for pitched roofs to get the maximum yield. With an elevation angle, the slope of the module can be adjusted to gain the maximum annual efficiency. The construction of that elevation angle each containing a support, bearing and base angle is aligned and assembled locally. An optimum utilization of the roof surface is achieved when all elevation angles are erected on a continuous base angle. The distance between the module rows depends on the shade factor. The type of mounting system used depends on the roof covering. Hanger bolts, trapezoidal shoes or roof-hooks can all be used for attaching the angles. The selection of the material and design is determined by the individual parameters (e. g. slope of the roof, wind and snow load). Vertically and horizontally mounted modules Elevation with continuous base angle Fastening with hanger bolt, roof hook or trapezoidal shoe Our Check list elevation angles can be found at www.altec-metalltechnik.de/en/downloads/ Overview mounting systems 31
ALTEC FD_COMPACT Optimised flat roof ballast system Also suitable for higher snow loads! Both the South and the eastwest-elevated system are suitable for use on most flat roofs with a maximum slope of 5. The 15 angle frames are physically connected by a continuous base rail. Thanks to this cross-linked structure an area up to within 0.5 m from the roof edge can be used for module placement. This is possible on a building height of up to 25 meters, even for flat roofs without parapets. The framed modules are horizontally attached to the frame bases which allows rapid assembly without any need for additional clamps. The ALTEC flat-roof mounting system has been optimised by wind tunnel tests. For south facing elevations the ballast is applied on the rear wind sheet, with the eastwest elevation frames have ballast laid on the rails underneath the modules. Overview mounting systems 32 Our Check list ballast optimised flat roof system can be found at www.altec-metalltechnik.de/en/downloads/
ALTEC FD_VARIO Flat roof systems with different elevation angles Ballast free adhesive mounting This elevation can be fixed to almost all foil and bitumen roofs without ballasting. The rails are fixed directly to the roof with special laminate pointing. The roof covering has to be sufficiently fixed to the load carrying frame. The installers must be certified before commencement. The modules can be arranged exclusively horizontally next to each other. Advice, planning and projection occurs by our trained staff. Edging stone ballasting If edging stones are used to weigh down the system, these are put directly onto the arms of the aluminium T-profile. You should put building protection mats under the elevation angles to protect the roofing and prevent indentations. A vertical and horizontal module assembly is possible. The installation of wind plates can reduce the required ballast. Our Check lists elevation angles and ballast free adhesive mounting can be found at www.altec-metalltechnik.de/en/downloads/ Overview mounting systems 33
ALTEC Metalltechnik GmbH Industriegebiet 1 0724 Crispendorf GERMANY Phone +4 3663 4210-0 Fax +4 3663 4210-211 info@altec-metalltechnik.de www.altec-metalltechnik.de facebook.com/altec.metalltechnik All rights reserved 2018 ALTEC Metalltechnik GmbH Photos: ALTEC Metalltechnik GmbH Photo U1: thinkstockphotos.de All information about product characteristics, such as measurements, weights and colours in the catalog is based on available knowledge at time of printing, subject to technical changes and errors. Our Terms and Conditions of Sales and Delivery can be found on our website at www.altec-metalltechnik.de All dimensions are indicated in mm.