JANUARY, 2017 FEATURES 1 Features High performance ratings for structural, air infiltration and water resistance Meets AAMA performance class and grades of HC60, HC80, HC100 and HC120 Meets South Florida Building Code and SBCCI SSTD 12 for Small Missile Impact Resistance Forced Entry Resistance tested per AAMA 1303. Available as,,,, and configurations ptional vertical mullions for additional sidelites Accommodates 3/16", 7/32", 1/4", /16", 3/8", 1/2", 9/16", /8" and 1" infills ptional factory glazing (Sliding Panels nly) Heavy duty stainless steel casters Stainless steel track insert for sliding panels Stainless steel MS Hookbolt Lock ptional architectural finishes including anodized and applied coatings Interior or exterior insect screens
2 BLANK PAGE JANUARY, 2017
JANUARY, 2017 INDE 3 ELEVATINS...4 STANDARD DETAILS... thru 7 INSECT SCREENS / INFILL PTINS...8 HARDWARE PTINS...9 WINDLAD CHARTS...10 LAWS AND BUILDING AND SAFETY CDES GVERNING THE DESIGN AND USE F GLAZED ENTRANCE, WINDW, AND CURTAIN WALL PRDUCTS VARY WIDELY. KAWNEER DES NT CNTRL THE SELECTIN F PRDUCT CNFIGURATINS, PERATING HARDWARE, R GLAZING MATERIALS, AND ASSUMES N RESPNSIBILITY THEREFR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI ) units are found in these details: m meter cm centimeter mm millimeter s second Pa pascal MPa megapascal
4 ELEVATINS JANUARY, 2017 ELEVATINS ARE NUMBER KEYED T DETAILS 3 1 1 3 FIED SLIDE 6 7 4 2 UNIT 3 3 1 7 PP. SLIDE FIED 6 PP. 2 4 UNIT 3 1 PP. 3 FIED FIED 10 4 4 UNIT SLIDE 6 7 2 3 1 FIED SLIDE 6 4 2 UNIT 1 3 FIED SLIDE SLIDE FIED 6 8 6 PP. PP. FIED 9 PP. 4 4 2 2 4 UNIT
JANUARY, 2017 STANDARD DETAILS SCALE 3" = 1'-0' 6-3/32" (14.78) 2-2/32" (70.64) PERABLE HEAD (HC60/80/100/120) 3-3/32" (78.8) FIED HEAD (HC60) 1 3 3-3/32" (78.8) FIED HEAD (HC80/100/120) 3A 3-23/32" (94.46) 3-23/32" (94.46) 3-3/32" (78.8) 3-3/32" (78.8) 6-13/32" (162.72) PERABLE SILL (HC60/80/100) (HC120),, nly 2 PERABLE SILL (HC120) nly FIED SILL (HC60) 4 FIED SILL (HC80/100/120) 4A NTE: 9/16" INFILL SHWN. FR ADDITINAL GLAZING PTINS SEE PAGE 8. 2A
6 STANDARD DETAILS JANUARY, 2017 SCALE 3" = 1'-0" 1-1/4" (31.7) FIED JAMB (63.) INTERLCK STILE (HC60) 4-1/4" (109.9) LCK JAMB 6 7 1/8" (3.18) (63.) INTERLCK STILE (HC80/100) 6A (63.) INTERLCK STILE (HC120) 6B 1/8" (3.18) (63.) 3-1/4" (82.) (63.) 3-1/4" (82.) MEETING STILE (HC60/80) MEETING STILE (HC100/120) 8 8A
JANUARY, 2017 STANDARD DETAILS 7 SCALE 3" = 1'-0" 4-1/4" (109.9) LCK STILE MULLIN (HC60) 4-1/4" (109.9) LCK STILE MULLIN (HC80/100) 9 9A 2" 1" 4-1/4" (109.9) LCK STILE MULLIN (HC120) 2" 1" (63.) 9B 10 PTINAL MEMBERS FIED MULLIN HEAD RECEPTR ETERIR GLAZED HEAD RECEPTR INTERIR GLAZED NTE: Head Receptors cannot currently be used with Interior Screens.
8 INSECT SCREENS / INFILL PTINS JANUARY, 2017 SCALE 3" = 1'-0" ETERIR SCREENS HEAD INTERLCK LCK JAMB INSECT SCREEN HEAD SILL INSECT SCREEN NTE: Standard screen includes plated steel hardware. ptional screen available with stainless steel hardware. INTERIR SCREENS SCREEN WITH APPLIED CLSURE FR SCREEN LATCH INSECT SCREEN SILL INSECT SCREEN NTE: Also available with 3/16" and 7/32" infills. INTERLCK INFILL PTINS LCK JAMB NTE: Standard screen includes plated steel hardware. ptional screen available with stainless steel hardware. SCREEN WITH APPLIED CLSURE FR SCREEN LATCH 1/4" /16" 3/8" 1/2" 9/16" /8" 1"
JANUARY, 2017 HARDWARE PTINS 9 HARDWARE DESCRIPTIN AR MS 1847 LCK AR MS 180A-0 HKBLT (Interior) Extruded Pull with Thumbturn (Exterior) Extruded Pull with Applied Cylinder or Blank Extruded Pull (Interior) Extruded Pull with Thumbturn (Exterior) Blank Flush Pull (Interior) Full Length Extruded Pull with Thumbturn (on Lock Panel) (Exterior) Blank Flush Pull (Interior) Full Length Extruded Pull with Thumbturn (on Lock Panel) (Exterior) Blank Extruded Pull (Interior) Flush Pull with Slide perator (Exterior) Blank Flush Pull,,,,,, (Interior) Flush Pull with Slide perator (Exterior) Flush Pull with Cylinder,, (Interior) Blank Extruded Pull with Mortise Cylinder or Thumbturn (Exterior) Blank Extruded Pull with Mortise Cylinder (Interior) Blank Extruded Pull with Mortise Cylinder or Thumbturn (Exterior) Blank Flush Pull with Mortise Cylinder (Interior) Full Length Extruded Pull with Mortise Cylinder or Thumbturn (Exterior) Blank Extruded Pull with Mortise Cylinder (Interior) Full Length Extruded Pull with Mortise Cylinder or Thumbturn (Exterior) Blank Flush Pull with Mortise Cylinder,,,, (Interior) Dummy Flush Pull with Mortise Cylinder or Thumbturn (Exterior) Blank Flush Pull with Mortise Cylinder,,
10 WIND LAD CHARTS JANUARY, 2017 FR WINDLAD R DEADLAD INFRMATIN, PLEASE CNTACT YUR KAWNEER APPLICATIN ENGINEERING DEPARTMENT.