TOOLS Page Q 2 Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2 Page Q 3 Changeable carbide drill (WHM) Page Q 3/1 Drilling machine Tonisco Page Q 3/2 Page Q 4 Tools Pipe cutter, Chamfering tool, Saddle blade, Locking plier Page Q 4/1 Extractors, Hydrant-Master Universal Key, Operating key Page Q 4/2 Valve key 1", Assembly key Page Q 4/3 Q 1/1 Edition 11.2017
TOOLS Application examples Q 1/2 Edition 09.2015
Drilling machine For drilling under pressure Can be used for drilling pipes of steel, ductile iron, AC, PE and PVC When drilling under pressure, swarf is washed out via an outlet Rotated by ratchet handle and fed by feed wing nut The ratchet is connected to the drill shaft with a simple locking device Pipe saddle adapters and reducers are sealed with captivated rubber rings Drilling machine No. 5800 Order No. Description Content case Dimensions 360 5820 Drilling machine 5810 Case 5830 Ratchet 5840 Shaft 5850 Twist drill for steel, ductile iron and AC pipes 5860 Cup drill for PE and PVC-pipes 5890 Reducing adapter with rubber seals 5900 Equal adapter with rubber seals 5910 1 pc. Allen key size 5 5920 2 pc. C spanner for adapter 8401 Saddle blade for shut-off 5800 Complete in case (weight 17,5) 2" - 1" 2" - 1¼" 2" - 1½" 2" - 2" SW 5 1" - 1¼" 1½" - 2" 7 1 2 5 3 4 6 9 Suitable accessories 8 10 Cup drill for steel and ductil iron pipes: No. 5870 Reducing adapter with rubber seals (2" - 2½"): No. 5890 Adapter for ISO-combination tapping valve (2" - 1½"): No. 5940 Adapter for thread-cutting machine REMS AMIGO 2: No. 5008555 11 12 No. 5860 Cup drill For PE- and PVC-pipes No. 5850 Twist drill For steel, ductile iron and AC-pipes 1 Ratchet 2 Shaft locking bolt 3 Feed wing nut 4 Red marking 5 Drill shaft 6 Body 7 O-ring 8 Rubber seal 9 Ball valve outlet (carrier) 10 Adapter or reducer 11 Hexagonal socket 12 Twist drill Q 2/1 Edition 06.2017
Motorised Drilling machine Powered drilling machine with continuous feed 3 drive options Hand ratchet, petrol engine, pneumatic drive Also for under pressure drilling Massively increases the service life of the drilling tools For quick and simple drilling of ductile iron-, steel-, AC-, PE and PVC-pipes Motorised power and continuous feed are necessary for driving the special carbide drills which are needed for cement lined cast iron pipes Suitable accessories Content case Order No. Description 5825 Drilling machine 5815 Case 5830 Ratchet 5840 Shaft 5845 Short shaft for motorised drive 5850 Twist drill for steel, ductile iron and AC pipes 5860 Cup drill for PE and PVC-pipes 5890 Reducing adapter with rubber seals 5900 Equal adapter with rubber seals 5920 2 pcs. C spanner for adapter 8401 Saddle blade for shut-off 5805 Complete in case (weight 22,5) Dimension 2" - 1" 2" - 1¼" 2" - 1½" 2" - 2" 1" - 1¼" 1½" - 2" Cup drill for steel and ductile iron pipes: No. 5870 Reducing adapter with rubber seals (2" - 2½"): No. 5890 Adapter for ISO combination tapping valve (2" - 1½"): No. 5940 Special version for cement lined cast iron pipes and AC pipes: No. 5805W Carbide drill: No. 5855W Adapter for thread-cutting machine REMS AMIGO 2: No. 5008555 Drilling machine with hand ratchet Standard version (in metal case) No. 5805 Petrol engine including adapter for drilling machine No. 5805 No. 5835 Pneumatic (air consumption: 540 l/min) including adapter for drilling machine No. 5805 No. 5836 No. 5805 No. 5835 No. 5836 6 9 11 10 12 3 2 1 7 5 4 8 No. 5860 Cup drilling For PE- and PVC-pipes No. 5850 Twist drill For steel, ductile iron and AC-pipes 1 Cup drill or twist drill 2 Hexagonal socket 3 Adapter or reducer 4 Knurled nut 5 Gear transmission 6 Shaft 7 Shaft locking bolt 8 Ball valve (washout) 9 Carrier 10 O-ring 11 Red marking 12 Body Q 2/2 Edition 06.2017
Drilling machine Changeable carbide drill (WHM) Dimensiones: Cup drill for steel and ductile iron pipes No. 5870 Continuous feed and motorised power are necessary! Easy and cost saving replacement of worm cutting tips without any technical efforts One cutting tip holder for each two dimensions of cutting tips Available as set for one dimension each and in single components for an individual demand WHM-drill for cast iron, cement lined cast iron and AC pipes No. 5855W Order No. Description Dimensions 5855W 5856 5857 NN52 5911 WHM-drill complete WHM-cutting tip holder including set bolt WHM-cutting tip Borehole sealing sleeve Torx-set bolt for WHM-cutting tip holder TORX-pin key 1" - 1¼" 1½" - 2" 2" - Ø 36 GWS 25 1" - 1¼" GWS 32 1½" - 2" WHM-cutting tip holder No. 5856 WHM-cutting tip No. 5857 Set bolt No. NN52 TORX-pin key No. 5911 Q 3/1 Edition 02.2017
Drilling machine Tonisco The Tonisco drilling machine is suitable for drilling up to Ø 89 pipelines made of steel, ductile iron, AC, PE and PVC Manual feed by means of a feed nut with a handwheel TONISCO-drilling machine No. 5807 Content case Order No. Description Dimensions Drilling machine Case Electrical drive* Ratchet 220 V 50 Hz 1000 vatios Shaft + extensions Adapter for hole sawing 1¼" - Ø 30 1½" - Ø 38 Hole saw 5807 2" - Ø 44 DN 80 - Ø 70 DN 100 - Ø 89 Centre drill Ø 7 1" Drill adapter with external thread 1¼" 1½" 2" Drill adapter with flange DN 80 DN 100 * Attention: 230 V - please observe safety regulations. TONISCO-drilling machine No. 5807 can also be leased. Thread adapter Flange adapter Hole saw Centre drill Q 3/2 Edition 09.2015
TOOLS Cut pipes square and straight The lever design minimises the force required Pipe cutter Cuts PE- and PVC pipes No. 6050 Order No. For Ø Pipe Weight 6050 Model I: up to 1¼" or Ø 40 Model II: up to 2" or Ø 63 0,30 1,10 Symbol photo For easy assembly of ISO push-fit fittings the pipe should be beveled. We recommend our precision-made steel chamfering tool. This provides the correct chamfer when turned clockwise a few times on the pipe end Chamfering tool For beveling PE pipes No. 6000 Order No. Ø Pipe DN Weight 6000 20 ½" 0,07 25 ¾" 0,07 32 1" 0,10 40 1¼" 0,17 50 1½" 0,22 63 2" 0,62 For shut-off saddles and shut-off adapters For under pressure drilling Saddle blade No. 8401 Order No. Size Weight 8401 Model I: For saddle 1" - 1¼" Model II: For saddle 1½" - 2" 0,20 0,25 To hold and push the open POM clamp for the assembly of fittings with cone that can be dismantled (No. 6301) Made of stainless steel Locking plier No. 6011 Q 4/1 Edition 09.2015
TOOLS First ensure that the grip ring is not under tension. When pushed in, the extractors separate the grip ring from the pipe, which can then be pulled out Application: for all Hawle products with ISO push-fit fittings Extractors For dismantling ISO push-fit fittings No. 6010 Order No. Ø Pipe DN Qty. Extractors Weight 6010 20 ½" 2 0,04 25 ¾" 2 0,07 32 1" 2 0,09 40 1¼" 2 0,14 50 1½" 2 0,19 63 2" 2 0,36 75 3 0,18 90 3 0,31 110 3 0,41 ISO Made of aluminium and ductile iron with reversible ratchet For opening and closing For operating coupling caps A + B + C For operating hose couplings B + C For breaking theft indicator caps Hydrant-Master Universal Key Lightweight - robust - practical No. 3461 Order No. Weight 3461 2,50 Order No. Operating key for Length Weight 3410 Service valves 850 1,90 3420 Valves, extension spindles and below ground hydrants 1130 4,10 3460 Above ground hydrants 420 1,25 Operating key No. 3410 No. 3420 No. 3460 No. 3410/3420 No. 3460 Q 4/2 Edition 09.2015
TOOLS Installation tool to change air valve 1" No. 9876 Valve key For air valve 1" No. 3454 For assembling service valves No. 2491, No. 2500, No. 2520, No. 2800 Of stainless steel No damage to epoxy powder coating No stress on the bonnet Operated via size 36 hexagonal nut with regular spanner or using the ratchet of the HAWLE drilling machine Assembly key for service valves with internal thread No. 3456 Order No. For internal thread Weight 3456 1¼" / 2" 0,50 1" / 1½" 0,65 Q 4/3 Edition 11.2017
NOTES Q 4/4 Edition 11.2017