Installation Manual -G006 Corner Climber YM11554 63 ½ (1.61m) (0.69m) (0.51m) (0.51m) (0.69m) Yardistry Ltd. Mount Forest, ON Canada N0G 2L1 Toll Free Customer Support: 1.888.509.4382 info@yardistrystructures.com www.yardistrystructures.com evised 08/24/2011 1
!Important Safety Notice! Yardistry components are intended for privacy, decorative and ornamental use only. roduct is NOT INTENDED for the following: - A safety barrier to prevent unsupervised access to pools, hot tubs, spas, or ponds. - Safety railings for elevated platforms or decks. - As load bearing support for a building, structure, heavy objects or swings. - Used in structures that trap wind, rain or snow that would create extra load on the product. ermanent structures may require a building permit. As the purchaser and or installer of this product you are advised to consult local planning, zoning, and building inspection departments for guidance on applicable building codes and or zoning requirements. Wood is NOT flame retardant and will burn. Grills, fire pits and chimneys are a fire hazard if placed too close to a Yardistry structure. Consult user s manual of the grill, fire pit or chimney for safe distances from combustible materials. During installation, follow all safety warnings provided with your tools and use OHSA approved safety glasses. Some structures may require two or more people to install safely. Check for underground utilities before digging or driving stakes into the ground! General Information: Wood components are manufactured with Cedar (C. Lanceolata) which is protected with factory applied water-based stain. Knots, small checks (cracks) and weathering are naturally occurring and do not affect the strength of the product. Annual application of a water-based water repellent sealant or stain will help reduce weathering and checks. Warranty: Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer s installation instructions. atents ending Tape Measure Carpenters Level Carpenters Square Standard or Cordless Drill Tools equired #2 hillips or obertson Safety Glasses Bits or Screwdriver Adult ers 1/8 Drill Bit encil 8 Step Ladder Keys To Assemble Success This identifies information that requires special attention. Improper assembly could lead to an unsafe or dangerous condition. Check that set or assembly is properly level before proceeding. Use Level Use Measure Distance Use Where this is shown, 2 or 3 people are required to safely complete the step. To avoid injury or damage to the assembly make sure to get help! Check that assembly is square before tightening bolts. Use a measuring tape to assure proper location. Square Assembly re-drill 1/8 & 3/16 Bit re-drill a pilot hole before fastening screw or lag to prevent splitting of wood. This indicates time to tighten bolts, but not too tight! Do not crush the wood. This may create splinters and cause structural damage. Tighten Bolts 2 No Yes
Material List Top and Bottom ail - 7 1/4 (18.4cm) and 20 (50.8cm) S4 #8 x 2 1/4 Wood Screw S5 S7 #10 x 1 an Head Screw #8 x 1 1/2 Wood Screw 4x4 osts - 1x 63 (1.60m) and 49 1/4 (1.25m) (12) anel Clips (3) ost Caps A1 (2)Arch Topper X2 (2) Two High X anel 3
Insert male into female. Slide down altos a medida que se adquieran. à deux ou until à trois flush carreaux with de hauteur adjacent panel. *Use los tornillos de acero inoxidable (vendus séparément). de 2 1/4" que se incluyen en el juego *Utilisez les vis en acier inoxydable de Introduzca el extremo macho en de sujetadores de paneles para 2-1/4 el po fournies extremo dans le hembra. nécessaire de Deslícelo hacia abajo hasta que reforzar el ensamblado. fixations quede pour panneaux al ras afin del fixer et panel adyacente. de renforcer l'assemblage. 1. emove the upper metal connectors on both sides of X2 - Two High X anel. eattach the metal connectors to X2 by 2securing the bottom Assemble Insérez les two holes anels pièces of the metal side de by raccordement connectors side. mâles dans les pièces de raccordement femelles. to the Faites top two glisser holes on le X2 so that the metal connectors stick out from the Conecte top. panneau Slide los A1 vers paneles Arch bas lado Topper jusqu'à a lado. between ce qu'il the two soit protruding au même metal connectors on the top of X2. Attach the metal connectors to the factory drilled holes in A1. (Fig. 1A) *Ensure anels are Assemblez niveau que les le panneaux panneau côte adjacent. à côte. oriented correctly! (Fig. 1B) Step 1- Assemble Wings 2. Secure panels with a S4-2 1/4 Wood Screw the location indicated by the large arrow in the direction of the arrow. When pre-drilled holes are not available use a 1/8 Drill Bit to drill holes on an angle in the inside of the panel as shown. (Fig. F) 3. Secure -Top and Bottom ails to anel Assembly with S4-2 1/4 Wood Screws locations indicated by arrows in the direction of the arrow. *- Top and Bottom ails will overhang 1/4 on either side of panel. Except on Arch Topper!! Thick iece of Wood Fig. F 2 1/4 Screw * - Top and Bottom ails may Small Connectors. need to be cut to 20 (50.8cm) emove the male connectors from the outside of the C. nectores and 7 1/4 (18.4cm) panel assembly. les petites (It pièces is recommended to use a Mitre Quite los conectores masculinos del exterior de la nt. Box or Mitre Saw) asamblea de panel. 4. epeat until two panel assemblies Enlever les connecteurs mâles de l'extérieur de are created. l'assemblée de panneau. Groove Drill Hole on an Angle Skinny iece of Wood A1 male connector conector masculino connecteur mâle short male connector ctory drilled holes. ros pretaladrados. répercés à l'usine. ilot holes to the right Fig. 1B - Filler Strips on Bottom of anel! Screws* are 2 1/4" stainless steel included in anel Clip set. Los tornillos* son de acero inoxidable de 2 1/4" y se incluyen en el juego de sujetadores de paneles. *Les vis sont celles de 2-1/4 po en acier inoxydable qui sont fournies dans le nécessaire de fixations pour panneaux. conector masculino corto le connecteur mâle court Fig. 1A x2 X2 A1 Arch Topper Top & Bottom ail At 7 1/4 (18.4cm) X2 Two High X anel Top & Bottom ail At 20 (50.8cm) 8x S4 #8-2 1/4 Wood Screws 4
Step 2- Attach anel Clips For Wings 1. On a flat surface place - 4x4 ost on its side and position anel Clips in locations indicated in Figures 1 and 1A. Ensure anel Clips are oriented as shown in Diagrams! 2. anel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3/8 or 3.49cm away from the side of the post as shown in Fig. 2. 3. With anel Clips in place, mark screw holes with a pencil and pre-drill holes with a 1/8 drill bit. (Not provided) 4. Secure anel Clips in locations indicated in figure 1 and 1A with S7- #8 x 1 1/2 wood screws. 5. epeat for each post configuration. Fig. 1A- Top View C Fig. 2 1 3/8 (3.5cm) re-drill holes and secure with S7- #8 x 1 1/2 Wood Screws Note: ost A has anel Clips on two sides! B A Front View Fig. 1 Side View Fig. 1 B A C (138.2cm) (111.8cm) 38 38 38 (101.6cm) (96.5cm) (101.6cm) (96.5cm) (101.6cm) (96.5cm) (111.8cm) (20.3cm) (20.3cm) (20.3cm) 4x4 ost at 49 1/4 (1.25m) 1 - anel Clips 1x 4x4 ost at 63 (1.60m) 24x S7 #8 x 1 1/2 Wood Screw 5
Step 3- Attaching ost Caps 1. lace a ost Cap on each 4x4 ost 2. Secure ost Cap with 2 S7- #8-1 1/2 Wood Screws x3 3x ost Caps 6x S7 #8-1 1/2 Wood Screws 6
This identifies information that requires special Step 4- Attach attention. Wings Improper assembly to could osts lead to an unsafe or dangerous condition. Check that set or assembly is properly level before proceeding. Use Use re-drill 1/8 & 3/16 Bit Where this is shown, 2 or 3 1. lace panel assemblies on posts as shown people (Fig.1) are allowing required to a safely 2 gap between the bottom of the post and the bottom edge complete of the bottom the step. rail To avoid on the panel assembly. Note: Assemble with the help injury of another or damage adult! to the assembly make sure to get help! 2. With a 1/8 drill bit, predrill holes as shown in figure 2. 3. Fasten the panel assembles Measure to Check the post that and assembly anel is Clips square with a Square S5-1 an Head Screw provided Distance in location before of circles. tightening (Fig. bolts. 1) Assembly *osts must be securely installed to support structure. Consult local Use a measuring tape to assure building codes and ground conditions proper location. for required footing design. It is recommended the structure be secured to existing stone, concrete or deck. CAUTION rotrusion Hazard Once the assembly is tightened, watch for Fig. exposed 1 threads. If a thread protrudes from the T-Nut, remove the bolt and add washers to eliminate this condition. Extra washers have been provided for this purpose. roper Hardware Assembly Lag screws require drilling pilot holes to avoid splitting wood. Only a flat washer is required. For ease of installation liquid soap can be used on all lag-type screws. For bolts, tap T-Nut into hole with hammer. Insert the hex bolt through lock washer first then flat washer then hole. Because the assemblies need to be squared do not completely tighten until instructed. ay close attention to diameter of the bolts. 5/16 is slightly larger than 1/4. Note: Wafer head bolts with blue lock tight or a bolt with a Ny-Lok nut do NOT require a lock washer. Lag Screw Hex Bolt Lock Washer Flat Washer 6 re-drill a pilot hole before fastening screw or lag to prevent splitting of wood. This indicates time to tighten bolts, but not too tight! Do not crush the wood. This may create splinters and cause structural damage. Fig. 2. redrill Holes and Fasten with NoS5-1 an Head Screw If Bolt protrudes beyond T-Nut Lag Assembly Flat Washer Bolt Assembly Use an extra Flat Washer Tigh Bo Ye Before mounting use factory drilled guides to drill 1/8 T-Nut (Hammer Do not cr B 2 (5.1cm) A 2 (5.1cm) C 1 4x4 ost 1 S5 #10 x 1 an Screws 7