IP67 ~
SPECIFICATION MODEL OUTPUT INPUT PROTECTION OTHERS NOTE VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT(Typ.) LEAKAGE CURRENT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. MAX. CASE TEMP. EMC IMMUNITY MTBF DIMENSION PACKING Note.5 WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC DC VOLTAGE RATED CURRENT RATED POWER Note.5 CONSTANT CURRENT REGION Note.2 CURRENT RIPPLE CURRENT TOLERANCE SETUP, RISE TIME Note.6 HOLD UP TIME (Typ.) TOTAL HARMONIC DISTORTION MAX. No. of PSUs on 16A CIRCUIT BREAKER OVER CURRENT SHORT CIRCUIT SAFETY STANDARDS Note.8 WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION 40W Constant Current Mode LED Driver Note.8 0ms, ms / 115VAC 16ms/230VAC 16ms/115VAC 500ms, ms / 230VAC 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF 0.97/115VAC, PF 0.95/230VAC, PF 0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) LPF40D12 LPF40D15 LPF40D LPF40D24 LPF40D30 LPF40D36 LPF40D42 LPF40D48 LPF40D54 12V 15V V 24V 30V 36V 42V 48V 54V 3.34A 2.67A 2A 1.67A 1.34A 1.12A 0.96A 0.84A 0.76A 40.08W 40.08W 40W 40.08W 40.2W 40.32W 40.32W 40.32W 41.04W 7.2 ~12V 9 ~ 15V 12 ~ V 14.4 ~ 24V 18 ~ 30V 21.6 ~ 36V 25.2 ~ 42V 28.8 ~ 48V 32.4 ~ 54V 5.0% max. @rated current ±5.0% THD< %(@load %/115VC,230VAC; @load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) 84% 85% 86% 87% 88% 88% 88.5% 89% 89% 0.6A / 115VAC 0.3A / 230VAC 0.25A/277VAC COLD START 50A(twidth= 210μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 12 units (circuit breaker of type B) / units (circuit breaker of type C) at 230VAC <0.75mA / 240VAC 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed. 15 ~ 17V 17.5 ~ 21V 23 ~ 27V 28 ~ 35V 34 ~ 40V 41 ~ 49V 46 ~ 54V 54 ~ 63V 59 ~ 66V Shut down o/p voltage, repower on to recover Shut down o/p voltage, repower on to recover Tcase=40 ~ (Please refer to OUTPUT LOAD vs TEMPERATURE section) Tcase= ~ 95% RH noncondensing 40 ~, 10 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750, CSA C22.2 No. 250.008(except for 48V, 54V), ENEC EN613471, EN61347213 independent, EN62384, IP67, J613471, J61347213 approved ; design refer to UL9501, TUV EN9501 I/PO/P:3.75KVAC I/PO/P:M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015,EN6032 Class C (@load %) ; EN6033 Compliance to EN6042,3,4,5,6,8,11; EN61547, light industry level ( surge immunity LineLine 2KV) 1144.7K hrs min. Telcordia SR332 (Bellcore) ; 394.9Khrs min. MILHDBK217F (25 ) 162.5*43*32mm (L*W*H) 0.45Kg; 32pcs/15.4Kg/0.93CUFT
BLOCK DIAGRAM fosc : KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.L.P. V V DIM DIM O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. Vo(%) (min.) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 Io(%) Typical output current normalized by rated current (%)
DIMMING OPERATION 3 in 1 dimming function AC/N(Blue) AC/L(Brown) LPF40D V(Red) V(Black) DIM(Blue) DIM(White) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) % 90% % 70% % 50% 40% 30% % 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) % 90% % 70% % 50% 40% 30% % 10% 10% % 30% 40% 50% % 70% % 90% % Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM DIM Additive Resistance Output current (%) % 90% % 70% % 50% 40% 30% DO NOT connect "DIM to V" % 10% 10K/N K/N 30K/N 40K/N 50K/N K/N 70K/N K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N L Relay Switch Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Brown Blue AC/L AC/N LPF40D DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture.
OUTPUT LOAD vs TEMPERATURE LOAD (%) 40 LOAD (%) 40 40 30 0 15 30 40 50 70 (HORIZONTAL) 40 30 15 0 15 30 50 65 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 70 LOAD (%) 90 70 50 40 90 125 135 145 155 165 175 1 0 230 305 INPUT VOLTAGE (V) Hz Derating is needed under low input voltage. PF 1 0.99 0.98 0.97 0.96 0.95 0.94 0.93 0.92 0.91 0.9 0.89 0.88 0.87 0.86 0.85 0.84 50% % 70% % 90% % (40W) LOAD 277VAC 230VAC 115VAC THD TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 70 24% 22% % 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% 50% % 70% % 90% % LOAD 277VAC 230VAC 115VAC EFFICIENCY vs LOAD possess superior working efficiency that up to 89% can be reached in field applications. 48V Model, Tcase at 70 EFFICIENCY(%) 93 92 91 90 89 88 87 86 85 84 83 82 81 79 78 77 76 75 74 73 72 71 70 10% % 30% 40% 50% % 70% % 90% % LOAD 277VAC 230VAC 115VAC
LIFE TIME 1 LIFETIME(Kh) 40 0 30 40 50 70 Tc a s e ( )
MECHANICAL SPECIFICATION CASE NO.: LPFB Unit:mm 162.5 3.5 AC/N(Blue) AC/L(Brown) 300± SJTW 18AWG 2C 3.5 ψ3.6 3.5 43 13 tc ψ3.6 3.5 300± Style 2464 18AWG 2C(V,V) Style 2464 22AWG 2C(DIM,DIM) V(Red) V(Black) DIM(Blue) DIM(White) tc : Max. Case Temperature 32 INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html