HRDWRE 4 - wood dowels 20 - cam 8 - large 12 - shelf pins 4 - adhesive cam covers 20 - cams 8 - brackets Missing hardware? Please call 800.606.6387 for replacements. WLL MOUNTING HRDWRE 2 - small 2 - large 2 - straps 4 - brackets 2 - plastic anchors Thank you for purchasing the Wood Grain 6 Shelf ookcase. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. s you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. Note: 2 people are required to safely assemble this product. COMPONENTS TOOLS REQUIRED phillips head screwdriver (We recommend the use of hand tools instead power tools) NOTE: Make sure arrows on each cam point toward nearest edge with holes 2 - fixed shelves 1 - bottom crossbar 3 - adjustable shelves 1 - top NOTE: Do not over tighten the cam 1 - crossbar 3 - back s top 2 - side s (1 left, 1 right) 1 ) Insert 2 wood dowels, 2 cam and 2 cams into crossbar as shown. Secure, but do not over tighten, cam, using a phillips head screwdriver. Make sure arrow on each cam point toward nearest edge with holes. ) Insert 2 wood dowels and 4 cam into top as shown. Page 1 of 5
right side bottom left side 2 Insert 7 cam and 2 cams into left and right side s as shown, using a screwdriver. 3 ) Insert 6 cams into bottom as shown. ) Insert 4 cams into each as shown. NOTE: Make sure grooves of fixed shelves, bottom assembly and left side positioned as shown crossbar bottom assembly bottom right side 4 Fit cam into corresponding holes of bottom as shown. Using a phillips head screwdriver, turn cams clockwise until each cam securely engages each cam screw. 5 Fit cam of right side into corresponding holes of 2 fixed shelves and bottom assembly. Make sure grooves of fixed shelves, bottom assembly and left side are positioned as shown. Secure all cams. Page 2 of 5
back back left side 6 Slide 2 back s into corresponding groves of assembled unit as shown. 7 With the assistance of another adult, fit cam of left side into corresponding holes of assembled unit as shown. Secure all cams. top back 8 Slide remaining back into corresponding groves of assembled unit as shown. 9 Fit cam of top into corresponding holes of left and right side s as shown. Secure all cams. Page 3 of 5
shelf pin NOTE: Do not over tighten the 10 With the assistance of another adult, position unit upright. Insert 12 shelf pins into assembled unit at desired shelf heights. 11 ttach 8 brackets to back of assembled unit with 8 large as shown. Secure, but do not over tighten, using a phillips head screwdriver. adhesive cam cover adjustable shelf CLENING ND CRE Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer. 12 ) Place 3 adjustable shelves onto shelf pins as shown. Make sure each shelf is securely supported by shelf pins. ) Fit 4 adhesive cam covers into exposed cams as shown. ssembly is now complete. Page 4 of 5
SFETY MOUNTING INSTRUCTIONS: For added safety and stability, it is recommended that the mounting hardware be installed. For safe mounting, it is essential to use anchors appropriate to your type (i.e. plaster, dry, concrete, etc.). Mount to wood studs whenever possible. ) ttach 2 brackets to back of unit using 2 small as shown. ) Determine the final location of unit. Mark position on the, approximately 2" below each bracket mounted to the back of the unit. C) Drill a hole in the stud. If the stud is not available, drill a hole in the that is slightly smaller in diameter than the anchor. Squeeze the wings of the plastic anchor and insert into the hold. If necessary, gently tap the plastic anchor until the flange of the anchor is flush with the. D) ttach brackets to the by inserting 1 large screw through each bracket and into each plastic anchor in the. E) Place the unit so the brackets on the back edge are aligned with the brackets on the. F) Lace one end of the strap through each bracket, and into the other end of the strap. G) Pull the strap tightly until secure. Wall mounting assembly is now complete. WLL C plastic anchor D bracket large screw small screw bracket F strap NOTE: If you are unsure about your type or what mounting method you should use, consult a qualified professional or your local hardware store. Page 5 of 5