Cabinet Storage Products

Assembly Instructions Storage Products (UltraStor, Acoustis, Adjustable Shelf, Cover Panels, Closure Panels) Wood Compartment Doors Full Wood Door Compartment Grille Doors Full Grille Door No Doors Contents Important User Information.............................. 2 General...2 Manufacturer...2 Intended Use...2 Warranty...2 Safety Precautions.................................... 3 Required Tools........................................ 4 Wall Fasteners - Not Supplied........................... 4 Fastener Parts List.................................... 5 Identification................................... 6 Assembly - Group 1................................... 12 Assembly - Group 2................................... Assembly - Group 3................................... 16 Assembly - Group 4................................... 18 Assembly - Group 5................................... 20 Assembly - Group 6 17.......................... 22 Assembly - Group 16 62......................... 24 Level s........................................ 25 Attach Doors - Description.............................. 27 Attach Doors - Acousti Doors Only.................. 28 Attach Doors - Grille Doors.............................. 29 Attach Doors - Individual Compartment Doors............... Attach Doors - Single Full-Length Doors................... 32 Attach Doors - Double Compartment Doors................. 34 Attach Doors - Double Full-Length Doors................... 36 Attach Backing - Acoustis Only..................... 38 Secure s - UltraStor............................. 39 Connect s Together...39 Secure s to Back Wall...41 To Secure s Back-to-Back...42 Secure s - Acoustis........................ 43 Connect s Together...43 Secure s 2-1/2 From Back Wall... 45 Cover Panel Installation................................ 46 End Cover Panels...46 Center Cover Panels...49 Closure Panel Installation............................... 50 Work Surface Tops (s 50-62 Only).................. 51 Maintenance.................................. 52 Compartment Labeling........................... 52 Visit the Storage Products web page at wengercorp.com for detailed instructions and videos. Note: Note: Please read and understand these instructions before assembling or setting up. If you need additional information, contact Wenger Corporation using the information below. Wenger Corporation 2018 Printed in USA 2018-09 Part #250B394-02 Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448 Questions? Call...USA: (800) 4WENGER (493-6437) Worldwide: +1-507-455-4100 wengercorp.com

Important User Information General Copyright 2018 by Wenger Corporation All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser s personal use. Printed and bound in the United States of America. The information in this manual is subject to change without notice and does not represent a commitment on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may appear in these instructions. In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions. The manufacturer reserves the right to change this product at any time. The information in this document is not intended to cover all possible conditions and situations that might occur. The end user must exercise caution and common sense when assembling or installing Wenger Corporation products. If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437) or +1-507-455-4100 worldwide. Manufacturer The UltraStor and Acoustis are manufactured by: Wenger Corporation 555 Park Drive Owatonna, MN 55060 (800) 4WENGER (493-6437) +1 (507) 455-4100 wengercorp.com Intended Use This product is designed to store musical instruments and garments. This product is intended for indoor use in normal ambient temperature and humidity conditions it must not be exposed to prolonged outside weather conditions. This product is intended to be assembled only as described in these instructions. Warranty This product is guaranteed free of defects in materials and workmanship for ten full years from date of shipment. A full warranty statement is available upon request. 2

Safety Precautions Throughout this manual you may find cautions and warnings which are defined as follows: WARNING means that failure to follow the instruction may result in serious injury or death. CAUTION means that failure to follow the instruction may result in serious injury or damage to property. Read all of these safety instructions before assembling or using the cabinets.! CAUTION Make sure anyone assembling or setting up the cabinets has read and understands these instructions.! CAUTION Failure to comply with Warnings and Cautions in this document can result in damage to property or serious injury.! CAUTION It is unsafe for only one person to assemble or move the cabinets.! CAUTION Make sure the cabinets are securely attached to walls or adjoining cabinets after assembly is complete.! CAUTION Always wear safety glasses and gloves when assembling or installing the cabinets.! CAUTION Assemble and install the cabinets only on flat, solid surfaces.! CAUTION Do not stand or walk on the top of any cabinet. 38 (973 mm) cabinets with work surface tops have a maximum load capacity of 250 lbs. (3 kg) for evenly distributed loads. All other cabinets have a top maximum load capacity of 50 lbs. (23 kg).! CAUTION Do not hang anything from cabinet doors or shelves. 3

Required Tools Open-End Wrenches: 1/4, 3/8, 7/16, 1/2" Screwdrivers: Flat Head, Phillips Head Hex Bits/Wrenches Cordless Drill with 3/16 and 3/8 Bits and Sockets Plastic Mallet Non-marring Clamps Carpenter s Level Carpenter s Square Tape Measure Utility Knife Impact Driver NOTE: To save assembly time, it is recommended to have more than one of each type of screwdriver on hand. Wall Fasteners - Not Supplied Because materials and construction of walls can vary, fasteners for attaching the cabinets to the structure are not provided. The installer must choose the appropriate fastener and follow the manufacturer s instructions.! CAUTION Inferior or improperly installed fasteners could cause the cabinets to tip over. Determine the construction of the walls. If cabinets are attached to the wall and adjacent cabinets; no attachment to the floor is required for standard installation. For seismic, peninsula or island configurations, cabinets would be attached to the floor. See Secure s on pages 39-45 for more information. Fastener Guidelines: If the wall is wood stud-and-drywall construction, attachment should be by lag screws (1/4 minimum). If the wall is metal stud-and-drywall construction, attachment should be by toggle bolt (1/4 minimum). If the wall is concrete block construction, attachment should be by Concrete screw (Tapcon) or toggle bolt (1/4 minimum). If the wall is poured concrete construction, attachment should be by Concrete screw (Tapcon) or wedge-type concrete anchors. Note: Each wall connection must be rated for a minimum of 500 lbs of tension. Other fasteners may be used if the connection strength requirement is met. 4

Fastener Parts List Assembly Fasteners 5 7 8 Wood Dowel 8-32 Insert Nut 1/4-20 x 1.38 Machine Screw 12 7 x 50 mm Hex Socket Screw 22 37 27 39 #7 x 5/8 Flat Head Screw #8 x 1-1/4 Pan Head Screw 1/4-20 x 5/8 Button Head Screw 20 #8 x 5/8 Pan Head Screw Tack Glide 23 1/4-20 Hex Nut 33 #8-32 x 3/4 Flat Head Screw 43 60 #8-32 x 1 Machine Screw 10-24 Hex Cap Nut 1/4-20 x 1.77 Machine Screw Cover Panel Fasteners 54 55 #8 x 1-1/4 Truss Head Screw 56 #8 x 1-3/8 Wood Screw 1/4-20 x 2.359 Machine Screw Work Surface Top Fasteners 57 59 #8 x 1.5 Wood Screw #8 x 5/8 Sheet Metal Screw 5 1/4-20 Insert Nut 0.35 x 0.6 Vinyl Cap

0 6 Identification STOP Locate the individual to be assembled and go the indicated page for instructions. s are grouped according to similar assembly procedures. Doors, Backing, End Panel Installation and placement will be adressed separately. 1519 05 see Group 1, page 08 050606 08 0101 04 0202 04 09 06 18 0901 07 04120505 03 12 06 1002 03 04 0808 0707 10 08 01 200909 07 02 03 01 06 05 13 01 02 03 04 08 02 06 05 03 09 07 01 06 04 05 08 02 07 04 03 08 01 01 07 08 0808 02 02 03 03 06 0606 05 0505 04 0404 01 01 09 07 0707 02 02 03 03 06 06 05 05 04 04 08 08 09 0 07 07 #1 #2 #4 #5 #13 #18 33 24 23 24 32 2331 22 36 34 22 21 24 19 23 21 24 20 23 22 1818 21 22 19 20 18 21 24 19 23 20 41 19 24 23 22 24 18 23 08 19 21 22 12 09 07 20 18 22 2412 23 10 20 2412 23 20 21212021 22 26 24 23 09 0819 081908 28 28 22 12 09 09 07 071807 18 1919 24 20 23 22 18 10 27 27 1818 29 10 29 27 20 21 26 13 22 25 24 20 23 27 26 22 18 2525 26 13 20 20 21 21 13 13 25 27 25 25 26 25 26 262626 26 27 272727 25252525 26 250A893 27 27 26 25 1919 50 42 #22 #23 #24 #25 51 52 42 42 41 6743 42 44 33 31 41 3265 42 66 41 43 65 42 44 47 31 45 46 42 33 33 33 31 31 32 45 43 47 32 32 44 43 424242 41 41 44 45 4646 45 41 43 42 44 41 43 41 43 43 4470444444 44 45 71 454545 4546 72 41 41 27 28 434343 26 29 25 250A700 45 46 46 250A700 28 43 28 28 27 44 44 29 27 27 250A700 2626 26 29 29 45 45 46 46 2525 25 250A700 250A893 250A893 250A700 250A893 250A700 250A700 250A700 250A893 250A700 250A893 250A700 250A893 250A700 250A893 250A700 250A893 250A893 250A893 250A893 3636 42 #19 36 24 36 36 36 24 45 3636363646 36 #20 #21 54 #26 #27 #28 #29 55 56 #46 50 5050 50 75 76 67 76 7575 66 65 73 44 75 76 7347 6776 67 67 45 74 74 46 70 73 65 44 6574 65 7566668266 76 7171 7272 73 4470 44 47 45 74 46 75 76 76 47 47 71 72 45 45 80 46 46 80 70 75 73 75 76 83 74 71 72 73 79 79 70 75 76 78 78 74 73 71 72 75 76 81 74 70 76 73 58 74 77 75 75 71 71 72 7272 72 73 70 70 77 76 73 74 71 74 70 71 73 7077 77 74 7 73 74 71 71 72 72 70 70 77 77 77 Continued on following page. 77777777 77 6 54 5454 54

66 66 66 66 21 24 424 24 20 51 67 67 67 22 36 36 36 24 23 41 41 41 26 25 28 2828 28 27 2727 27 26 2626 26 29 2929 29 (continued) 5555 52 53 5656 5757 Group 1 (continued), see page 12 55 54 55 55 51 52 80 54 5354 5582 51 52 53 54 79 81 25 2525 25 Identification 5454 50 50 78 53 5355 53 52 54 31 3131 31 27 250A893 250A893 250A893 56 56 5683 56 57 57 57 57 8383 56 55 80 80 80 54 54 80 44 4444 44 1 A893 5959 5858 57 42 82 83 82 82 81 55 59 83 83 #5155 #52 #54 #55 #56 59 #57 58 81 81 82 59 43 44 58 58 83 56 45 46 81 5966 58 56 57 66 66 65 65 65 65 71 71 72 7266 47 4747 47 45 4545 45 70 70 46 4646 4657 71 72 70 250A700 250C880 UltraStor Cover Panel 6060 59 58 83 83 er Panel rerpanel Panel er Panel 72 75 7575 75 60 6262 73 76 7676 76 61 60 60 60 60 59 59 #60 #61 74 60 60 56 28 250A700 250A700 250A700 57 33 3333 34 43 43 32 3232 32 29 59 58 #58 47 60 67 6767 67 73 73 73 50 5050 50 61 65 74 74 74 6161 58 58 #59 42 42 42 77 7777 77 61 61 75 #70 62 62 62 78 7878 78 62 #71 54 5454 54 #72 76 79 7979 79 61 61 61 61 62 80 8080 80 77 81 8181 81 78 79 82 8282 82 83 8383 8 62 62 #73 #77 #78 #79 #80 250C880 250C880 250C880 250C880 UltraStor UltraStor UltraStor UltraStor Cover Cover Cover Cover Panel Panel Panel Panel 250C880 UltraStor Cover Pane 62 6262 6 Continued on following page. 7

13 19 19 Identification (continued) 29 27 A700 700 2528 A700 25 25 2528 28 78 78 32 34 #10 33 # 32 44 44 66 6633 45 65 43 46 45 46 32 4546 65 32 46 47 33 47 4629 29 29 29 47 4731 31 45 28 28 28 28 50 46 65 66 47 32 32 15 27 29 13 27 29 2913 13 13 35 33 33 31 33 17 17 31 28 28 31 17 31 3132 33 1 15 15 153 35 34 42 42 41 41 #8 43 #9 44 43 44 45 43 46 44 45 45 43 46 44 43 28 44 29 250A700 250A700 27 26 250A893 250A893 27 27 27 26 26 26 29 29 67 65 50 52 51 67 66 50 50 51 33 # 3551 67 33 47 34 31 67 66 33 65 32 46 66 45 65 47 31 47 33 33 47 31 31 3445 6667 65 6632 32 32 46 65 35 47 67 66 35 65 34 # 51 53 #43 72 72 74 7547 74 45 74 45 6575 45 45 65 79 78 80 #44 77 77 7565 73 75 73 7576 46 66 46 46 46 76 6678 78 79 #65 76 76 76 76 78 79 79 76 76 74 76 476674 67 47 47 47 67 79 79 77 77 80 81 #66 79 77 80 77 77 77 80 #45 82 #74 54 #47 67 65 65 65 65 77 77 7778 81 50 75 75 50 80 80 78 83 55 66 66 66 66 78 78 78 79 82 54 54 #75 50 #50 54 76 7651 51 81 81 79 5854 55 55 #81 55 51 #53 56 57 67 52 52 67 67 67 82 82 79 79 77 77 79 80 80 83 59 55 66 52 53 55 55 54 54 76 76 71 3 44 4671 44 4444 47 7447 7 31 33 32 29 31 31 12 15 26 26 28 12 12 28 13 25 25 12 27 27 28 27 28 29 15 28 29 12 10 26 26 10 10 10 29 26 27 29 13 2713 31 27 24 24 23 23 2421 23 22 22 24 23 22 20 20 2421 23 24 3 22 22 Group 2, see page 09 24 23 07 1008 09 08 08 08 09 09 09 07 07 0710 26 28 25 12 28 27 25 27 26 25 12 10 26 25 26 25 50 50 50 50 52 56 53 53 80 80 78 78 80 83 83 81 81 58 56 56 5351 51 51 51 57 81 81 81 82 59 54 54 54 5456 57 57 57 #82 250C880UltraStor UltraStor CoverPanel Panel 250C880 250C880 250C880UltraStor UltraStorCover CoverPanel Panel 250C880 UltraStorCover Cover 250C88082UltraStor Cover Panel 61 Panel 60 80 83 Panel 80 82 250C880 Cover 7981 82 80 80 80 83 UltraStor 81 78 82 82 82 58 79 79 79 78 78 78 81 81 81 81 82 59 83 58 81 59 58 250C880 250C880 Ul U 61 83 59 83 83 83 60 62 62 UltraStor Cover Panel250C880 UltraStor Cover Panel 62 8 250C880 UltraStor Cover Panel 250C880 UltraStor Cover Panel 55 55 Continued on following page. 62 60 61 60 61 60 61

Identification (continued) Group 3, see page 16 67 #12 #15 #67 #76 #83 Group 4, see page 18 31 32 33 #31 #32 #33 #34 #35 #36 Continued on following page. 9

Identification (continued) Group 5, see page 20 07 #3 #6 #7 Group 6, see page 22 17 #17 #62 10

Before Installation Overview Assembly and installation should be performed by skilled technical persons, and only after carefully studying these instructions. It is suggested that the cabinets are setup in a space that is large enough to safely handle the cartons, pieces, finished cabinets, and dunnage. Inspect the condition of the wall and floor where the cabinets will be located. If the wall is not straight, establish a reference line so that the fronts of all cabinets will line up. Also, determine the highest point on the floor, which will establish the leveled height of each row of cabinets. Build only one cabinet at a time, to avoid intermixing parts. Build each according to these instructions for the specific model. Do not start installing doors until all cabinets are assembled and in their final location, leveled, and secured to adjacent walls and cabinets. After all cabinets are in place, distribute the door cartons and door hardware sets to each cabinet. Assemble and hang the doors one at a time according to the instructions. Then clean off any fingerprints, dirt, and dust, using a clean rag and mild spray cleaner or acetone. Before You Begin Keep the Packing List with the cabinet, for reference until the unit is completely assembled. Read the complete assembly procedure before beginning the assembly. The cabinet carton is marked with the cabinet number as shown in Identification. Hardware packs may contain extra fasteners that are not required on all cabinets. Because of the variety of possible wall surfaces, wall fasteners are not included. Have your maintenance personnel recommend an appropriate type for safe, secure attachment and have the fasteners available before assembling the cabinet. At least two people (preferably four) are required to assemble the cabinet and set it upright. Installation Procedures 1. Identify which is being assembled. Refer to Identification, the cabinet carton and any installation drawings. 2. Assemble the cabinet according to Assembly on pages 12-24. 3. Level the cabinet according to Level s on pages 25-26. 4. If the cabinet has doors, attach them according to Attach Doors on pages 27-37. 5. If the cabinet is an Acousti, attach the backing material according to Secure Backing on page 38. 6. Secure cabinets to the structure walls or secure them together according to Secure s on pages 39-45. 7. Install optional cover panels to the exposed cabinet ends according to Cover Panel Installation on pages 46-49. 8. Install top closure panels to close empty spaces behind cabinets according to Closure Panel Installation on page 50. 9. For s 50-62, attach work surface tops according to Work Surface Tops on page 51.

Assembly - Group 1 s 01, 02, 04, 05, 13, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 46, 51, 52, 54, 55, 56, 57, 58, 59, 60, 61, 70, 71, 72, 73, 77, 78, 79, 80 Hardware used: 8-32 Insert Nut t #8 x 5/8 Pan Wood Tack Head Screw 1$ 1/4-20 x 1.38 Dowel Glide 1@ i 7 x 50 mm Hex Machine Screw Socket Screw 1! Fixed Height u Shelf Clip y Leveler Bracket 1# 5 8 9 Left Hinge or Right Hinge Detail 1A Detail 1F 12 4 5 3 Right Hinge or Left Hinge 13 1 Detail 1B Detail 1G 6 15 16 17 Fixed Shelf or Adjustable Shelf 7 Detail 1C 7 15 6 Detail 1D 16 Shelf Clip 13 4 Left Side Detail 1E Latch Detail 1H Shelf Pin 10 Right Side 2 12 12

Assembly - Group 1 (continued) Preassembly NOTE: For panel orientation: The Left Side Panel q, Right Side Panel w and any Center Panels e have a notch in the bottom front corner. The side panels also have a groove in the rear to receive the Back Panel r. 1. Install Door Mounts. Skip this step if doors will not be installed. a. Per each compartment, lay the Panels flat. For a left side door hinge, lay with the left surface up. For a right side door hinge, lay with the right surface up. b. See Detail 1A. Install door hinge mounts. Use a plastic mallet to pound 8-32 Insert Nuts t into the holes (three per Hinge Mount) located toward the front edge of each Panel. c. See Detail 1B. Install door striker plate mounts. Turn the panels over, use a plastic mallet to pound 8-32 Insert Nuts t into the holes (two per Striker Plate Mount) located toward the front edge of each Panel. 2. Install Shelf Clips. For Fixed Height Shelves only, Adjustable Height Shelf Clips are pre-installed. a. See Detail 1C. Per each compartment, turn the panels so their inside surface is up. b. Push Fixed Height Shelf Clips y (two Clips in each panel side/four per shelf) into the inside surface of both compartments (Side or Center Panels). c. Turn any Center Panels over and repeat on the other side. NOTE: Panels can be large and difficult to keep aligned when attaching together with screws. To assist, peg the panels first by inserting Wood Dowels to fit snugly into 5/16 -diameter holes in the Panels. They may need to be tapped into place. 3. Insert Wood Dowels i into: the left and right side edges of the Top Panel o the top edge and notch of any Center Panels e the backside of the Bottom Front Stretcher Panel 1). Panel Assembly 1. Turn the Left and Right Side Panels q and w on edge, with the front edges down. With Wood Dowels i, peg the Side Panels to the Top Panel o. Attach the Side Panels to the side edges of the Top Panel o with 7 x 50 mm Hex Socket Screws 1!. 2. s 05, 19, 24 only. See Detail 1D. Attach one Tube 1& to both the Left and Right Side Panels q and w with one 1/4-20 x 1.38 Machine Screw u on each side. The Tube will slide through any Center Panels. 3. Peg any Center Panels e to the Top Panel o and attach them with 7 x 50 mm Hex Socket Screws 1!. 4. Attach the Back Panel r. a. See Detail 1E. The Bottom Stretcher Panel overlaps the bottom edge of the Back Panel. b. With the three Rear Stretcher Panels facing up, slide the Back Panel into the groove on the Side and Top Panels. 5. Attach the sides of the Rear Stretcher Panels to both Side Panels, using 7 x 50 mm Hex Socket Screws 1!. 6. Turn the assembly to face the front edges up. 7. Check that the assembly is square and tighten all screws. Attach Glides and Levelers 1. See Detail 1F. Tack Glides help protect corners and edges while moving the into place. Push or hammer plastic tack glides 1@ into the bottom edge of the Side and any Center panels, about 2 from the corners. 2. With Wood Dowels i, peg the Front Stretcher Panel 1) to the notch in the Side Panels and any Center Panels. 3. Attach Leveler Brackets. a. See Detail 1G. Attach Leveler Brackets 1# to the inside of all four corners of the cabinet using #8 x 5/8 Pan Head Screws 1$. The Leveler Brackets attach to the inside of both Side Panels and to the Front or Rear Stretcher Panels. b. If there are Center Panels, attach only one Leveler Bracket to the left-front side of the right-most Center Panel. Attach the other side to the Front Stretcher Panel. c. After the Leveler Brackets are attached, screw the levelers in so the plastic glides extend slightly further than the bottom of the levelers. Install Upper Shelves 1. Tip the assembled upright. 2. Recheck that the is square. 3. Recheck and tighten all hex-socket screws. 4. See Detail 1H. Starting at the top of the, snap in the upper levels of shelves. Do not install Shelves in 38 tall cabinets. a. For Fixed Height Shelves 1%, snap each shelf down into the Shelf Clips at each corner. b. For Adjustable Height Shelves 1^, flip the Shelf Pin down the in each corner at the desired shelf height and slide the shelf onto the Shelf Clips until the Latch clicks. To remove a shelf, pull out on the Latch and slide the shelf out. Wider shelves may have a Latch on each side. NOTE: To simplify leveling, do not install any lower levels of Shelves yet. Final Adjustment 1. Slide the assembled to the intended location. 2. Level the using a 1/4 socket or wrench on the leveler brackets. See Leveling s on page 25. 3. Install the remaining Shelves into the lower levels. Final Bank Assembly 1. Assemble, position and level any remaining cabinets. 2. After all cabinets in the bank have been positioned: a. Attach the Doors. See Attach Doors on page 27. b. Secure the cabinets, see Secure s on pages 39-45. 13

Assembly - Group 2 s 08, 09, 10,,,, 43, 44, 45, 47, 50, 53, 65, 66, 74, 75, 81, 82 Hardware used: 8-32 Insert Nut t #8 x 5/8 Pan Wood Tack Head Screw 1$ 1/4-20 x 1.38 Dowel Glide 1@ i 7 x 50 mm Hex Machine Screw Socket Screw 1! Fixed Height u Shelf Clip y Leveler Bracket 1# 5 8 Left Hinge or Right Hinge 12 9 4 Detail 2A Detail 2F 5 13 Right Hinge or Left Hinge 1 Detail 2B Detail 2G 6 Fixed Shelf or Adjustable Shelf 15 16 7 Detail 2C 4 6 18 Detail 2D 19 16 13 Left Side Detail 2E Latch Detail 2H Shelf Pin 10 Right Side 2 12

Assembly - Group 2 (continued) Preassembly NOTE: For panel orientation: The Left Side Panel q and Right Side Panel w have a notch in the bottom front corner. The side panels also have a groove in the rear to receive the Back Panel r. 1. Install Door Mounts. Skip this step if doors will not be installed. a. Per each compartment, lay the Panels flat. For a left side door hinge, lay with the left surface up. For a right side door hinge, lay with the right surface up. b. See Detail 2A. Install door hinge mounts. Use a plastic mallet to pound 8-32 Insert Nuts t into the holes (three per Hinge Mount) located toward the front edge of each Panel. c. See Detail 2B. Install door striker plate mounts. Turn the panels over, use a plastic mallet to pound 8-32 Insert Nuts t into the holes (two per Striker Plate Mount) located toward the front edge of each Panel. 2. Install Shelf Clips. For Fixed Height Shelves only, Adjustable Height Shelf Clips are pre-installed. a. See Detail 2C. Per each compartment, turn the panels so their inside surface is up. b. Push Fixed Height Shelf Clips y into the back inside surface of both compartments. Bottom Shelf requires two Clips in each panel side/four per shelf and Upper Shelves require one Clip in each panel side/two per shelf) NOTE: Panels can be large and difficult to keep aligned when attaching together with screws. To assist, peg the panels first by inserting Wood Dowels to fit snugly into 5/16 -diameter holes in the Panels. They may need to be tapped into place. 3. Insert Wood Dowels i into: the left and right side edges of the Top Panel o the backside of the Bottom Front Stretcher Panel 1). Panel Assembly 1. Turn the Left and Right Side Panels q and w on edge, with the front edges down. With Wood Dowels i, peg the Side Panels to the Top Panel o. Attach the Side Panels to the side edges of the Top Panel o with 7 x 50 mm Hex Socket Screws 1!. 2. Attach the Back Panel r. a. See Detail 2D. The Bottom Stretcher Panel overlaps the bottom edge of the Back Panel. b. With the three Rear Stretcher Panels facing up, slide the Back Panel into the groove on the Side and Top Panels. 3. Attach the sides of the Rear Stretcher Panels to both Side Panels, using 7 x 50 mm Hex Socket Screws 1!. 4. Turn the assembly to face the front edges up. 5. With Wood Dowels i, peg the Cross Stretcher Panel 1* to the Bottom Rear Stretcher Panel, then peg the Front Stretcher Panel 1) to it. 6. With Wood Dowels i, peg the Front Stretcher Panel 1) to the notch in the Side Panels. 7. s 50 and 53 only. See Detail 2E. Attach Top Front Stretcher Panel. a. Place the Top Front Stretcher Panel 1( underneath the Top Panel and between the Side Panels. b. Attach the sides of the Top Front Stretcher Panel to both Side Panels, using 7 x 50 mm Hex Socket Screws 1!. 8. Check that the assembly is square and tighten all screws. Attach Glides and Levelers 1. See Detail 2F. Tack Glides help protect corners and edges while moving the into place. Push or hammer plastic tack glides 1@ into the bottom edge of the Side and any Center panels, about 2 from the corners. 2. Attach Leveler Brackets. a. See Detail 2G. Attach Leveler Brackets 1# to the inside of all four corners of the cabinet using #8 x 5/8 Pan Head Screws 1$. The Leveler Brackets attach to the inside of both Side Panels and to the Front or Rear Stretcher Panels. b. After the Leveler Brackets are attached, screw the levelers in so the plastic glides extend slightly further than the bottom of the levelers. Install Upper Shelves 1. Tip the assembled upright. 2. Recheck that the is square. 3. Recheck and tighten all hex-socket screws. 4. See Detail 2H Starting at the top of the, snap in the upper levels of shelves. Do not install Shelves in s 50 and 53. a. For Fixed Height Shelves, rest the Shelf on the Rear Shelf Clips and attach the Front Support Tubes to the Side Panels using with one 1/4-20 x 1.38 Machine Screw u on each side. b. For Adjustable Height Shelves 1^, flip the Shelf Pin down the in each corner at the desired shelf height and slide the shelf onto the Shelf Clips until the Latch clicks. To remove a shelf, pull out on the Latch and slide the shelf out. Wider shelves may have a Latch on each side. NOTE: s 10 and have two upper shelves; has only one upper shelf, in the middle. NOTE: To simplify leveling, do not install any lower levels of Shelves yet. Final Adjustment 1. Slide the assembled to the intended location. 2. Level the using a 1/4 socket or wrench on the leveler brackets. See Leveling s on page 25. 3. Install the remaining Shelves into the lower levels. Final Bank Assembly 1. Assemble, position and level any remaining cabinets. 2. After all cabinets in the bank have been positioned: a. Attach the Doors. See Attach Doors on page 27. b. Secure the cabinets, see Secure s on pages 39-45. 15

Assembly - Group 3 s 12, 15, 67, 76, 83 Hardware used: 8-32 Insert Nut t 5 Wood Dowel i Tack Glide 1@ 7 x 50 mm Hex Socket Screw 1! #8 x 5/8 Pan Head Screw 1$ 1/4-20 Hex Nut 2@ 1/4-20 Insert Nut 2) 1/4-20 x 5/8 Button Head Screw 2# 1/4-20 x 1.77 Machine Screw 6) Leveler Bracket 1# 8 Left Hinge or Right Hinge Detail 3A 20 23 Detail 3F 9 4 4 1 Detail 3B 19 12 Detail 3C 23 13 15 16 Detail 3D Left Side 13 16 21 Detail 3E 22 60 Latch Detail 3G Shelf Pin 10 Right Side 2 12 16

Assembly - Group 3 (continued) Preassembly NOTE: For panel orientation: The Left Side Panel q and Right Side Panel w have a notch in the bottom front corner. The side panels also have a groove in the rear to receive the Back Panel r. 1. Install Door Mounts. Skip this step if doors will not be installed. a. Per each compartment, lay the Panels flat. For a left side door hinge, lay with the left surface up. For a right side door hinge, lay with the right surface up. b. See Detail 3A. Install door hinge mounts. Use a plastic mallet to pound 8-32 Insert Nuts t into the holes (three per Hinge Mount) located toward the front edge of each Panel. 2. See Detail 3E (s 12, 15 and 67 only). There are holes in each side panel that will be used later for shelf support bar screws (two holes per shelf in each side panel). Use a plastic mallet to pound 1/4-20 Insert Nuts 2) into these holes. NOTE: Panels can be large and difficult to keep aligned when attaching together with screws. To assist, peg the panels first by inserting Wood Dowels to fit snugly into 5/16 -diameter holes in the Panels. They may need to be tapped into place. 3. Insert Wood Dowels i into: the left and right side edges of the Top Panel o the backside of the Bottom Front Stretcher Panel 1). the top of the Top Front Stretcher Panel 1(. Panel Assembly 1. Turn the Left and Right Side Panels q and w on edge, with the front edges down. With Wood Dowels i, peg the Side Panels to the Top Panel o. Attach the Side Panels to the side edges of the Top Panel o with 7 x 50 mm Hex Socket Screws 1!. 2. Attach the Back Panel r. a. See Detail 3B. The Bottom Stretcher Panel overlaps the bottom edge of the Back Panel. b. With the three Rear Stretcher Panels facing up, slide the Back Panel into the groove on the Side and Top Panels. 3. Attach the sides of the Rear Stretcher Panels to both Side Panels, using 7 x 50 mm Hex Socket Screws 1!. 4. Turn the assembly to face the front edges up. 5. With Wood Dowels i, peg the Front Stretcher Panel 1) to the notch in the Side Panels. 6. Attach Top Front Stretcher Panel. a. Place the Top Front Stretcher Panel 1( underneath the Top Panel and between the Side Panels. b. Attach the sides of the Top Front Stretcher Panel to both Side Panels, using 7 x 50 mm Hex Socket Screws 1!. 7. Check that the assembly is square and tighten all screws. Attach Glides and Levelers 1. See Detail 3C. Tack Glides help protect corners and edges while moving the into place. Push or hammer plastic tack glides 1@ into the bottom edge of the Side and any Center panels, about 2 from the corners. 2. Attach Leveler Brackets. a. See Detail 3D. Attach Leveler Brackets 1# to the inside of all four corners of the cabinet using #8 x 5/8 Pan Head Screws 1$. The Leveler Brackets attach to the inside of both Side Panels and to the Front or Rear Stretcher Panels. b. After the Leveler Brackets are attached, screw the levelers in so the plastic glides extend slightly further than the bottom of the levelers. Install Upper Shelves 1. Tip the assembled cabinet upright. 2. Recheck that the cabinet is square. 3. Recheck and tighten all hex-socket screws. 4. See Detail 3E. If doors will be installed, attach a Bumper Assembly 2! to the center two holes under the Front Shelf Support Bar using 1/4-20 x 1.77 Machine Screws 6) and 1/4-20 Hex Nuts 2@. For Double Full-Length Doors: Attach the Bumper Assembly the front of the Bottom Shelf. For Double Compartment Doors: Attach the Bumper Assembly to the front of every Shelf. 5. See Detail 3F (Fixed Height Shelf s 12, 15 and 67 only). Using two 1/4-20 x 5/8 Button Head Screws 2# on each side, attach the Fixed Height Shelves 1% into the Screw Inserts installed in Preassembly Step 2. See Detail 3G (Adjustable Height Shelf s 76 and 83 only). Starting at the top of the, flip the Shelf Pin down in each corner at the desired shelf height and slide the Adjustable Height Shelves 1^ onto the Shelf Clips until the Latch clicks. To remove a shelf, pull out on the Latch and slide the shelf out. Wider shelves may have a Latch on each side. NOTE: To simplify leveling, do not install any lower levels of Shelves yet. Final Adjustment 1. Slide the assembled to the intended location. 2. Level the using a 1/4 socket or wrench on the leveler brackets. See Leveling s on page 25. 3. Install the remaining Shelves into the lower levels. Final Bank Assembly 1. Assemble, position and level any remaining cabinets. 2. After all cabinets in the bank have been positioned: a. Attach the Doors. See Attach Doors on page 27. b. Secure the cabinets, see Secure s on pages 39-45. 17

Assembly - Group 4 s 31, 32, 33, 34, 35, 36 Hardware used: 8-32 Insert Nut t #8 x 5/8 Pan Wood Tack Head Screw 1$ 1/4-20 x 1.38 Dowel Glide 1@ i 7 x 50 mm Hex Machine Screw Socket Screw 1! Fixed Height u Shelf Clip y Leveler Bracket 1# Left Hinge or 5 Right Hinge 13 8 9 4 Detail 4A Detail 4F 5 24 Right Hinge or Left Hinge 1 Detail 4B Detail 4G 6 7 15 16 Detail 4C 24 4 6 18 Detail 4D Left Side 13 10 12 Right Side 2 12 Detail 4E 18

Assembly - Group 4 (continued) Preassembly NOTE: For panel orientation: The Left Side Panel q and Right Side Panel w have a notch in the bottom front corner. The side panels also have a groove in the rear to receive the Back Panel r. 1. Install Door Mounts. Skip this step if doors will not be installed. a. Per each compartment, lay the Panels flat. For a left side door hinge, lay with the left surface up. For a right side door hinge, lay with the right surface up. b. See Detail 4A. Install door hinge mounts. Use a plastic mallet to pound 8-32 Insert Nuts t into the holes (three per Hinge Mount) located toward the front edge of each Panel. c. See Detail 4B. Install door striker plate mounts. Turn the panels over, use a plastic mallet to pound 8-32 Insert Nuts t into the holes (two per Striker Plate Mount) located toward the front edge of each Panel. 2. Install Shelf Clips. For Fixed Height Shelves only, Adjustable Height Shelf Clips are pre-installed. a. See Detail 4C. Per each compartment, turn the panels so their inside surface is up. b. Push Fixed Height Shelf Clips y into the back inside surface of both compartments. Bottom Shelf requires two Clips in each panel side/four per shelf and Upper Shelves require one Clip in each panel side/two per shelf) NOTE: Panels can be large and difficult to keep aligned when attaching together with screws. To assist, peg the panels first by inserting Wood Dowels to fit snugly into 5/16 -diameter holes in the Panels. They may need to be tapped into place. 3. Insert Wood Dowels i into: the left and right side edges of the Top Panel o the backside of the Bottom Front Stretcher Panel 1). Panel Assembly 1. Turn the Left and Right Side Panels q and w on edge, with the front edges down. With Wood Dowels i, peg the Side Panels to the Top Panel o. Attach the Side Panels to the side edges of the Top Panel o with 7 x 50 mm Hex Socket Screws 1!. 2. Attach the Back Panel r. a. See Detail 4D. The Bottom Stretcher Panel overlaps the bottom edge of the Back Panel. b. With the three Rear Stretcher Panels facing up, slide the Back Panel into the groove on the Side and Top Panels. 3. Attach the sides of the Rear Stretcher Panels to both Side Panels, using 7 x 50 mm Hex Socket Screws 1!. 4. Turn the assembly to face the front edges up. 5. With Wood Dowels i, peg the Cross Stretcher Panel 1* to the Bottom Rear Stretcher Panel, then peg the Front Stretcher Panel 1) to it. 6. With Wood Dowels i, peg the Front Stretcher Panel 1) to the notch in the Side Panels. 7. Check that the assembly is square and tighten all screws. Attach Glides and Levelers 1. See Detail 4E. Tack Glides help protect corners and edges while moving the into place. Push or hammer plastic tack glides 1@ into the bottom edge of the Side and any Center panels, about 2 from the corners. 2. Attach Leveler Brackets. a. See Detail 4F. Attach Leveler Brackets 1# to the inside of all four corners of the cabinet using #8 x 5/8 Pan Head Screws 1$. The Leveler Brackets attach to the inside of both Side Panels and to the Front or Rear Stretcher Panels. b. After the Leveler Brackets are attached, screw the levelers in so the plastic glides extend slightly further than the bottom of the levelers. Install Upper Shelves 1. Tip the assembled upright. 2. Recheck that the is square. 3. Recheck and tighten all hex-socket screws. 4. See Detail 4G. If the has a Hanger Bar 1%. a. Align the Hanger Bar tabs with the holes in the middle of both Side Panels. The flat surface of the bar (with holes) should face toward the front of the. b. Attach the Hanger Bar, using two #8 x 5/8 Pan Head Screws 1$ on each side. NOTE: When installing the Hanger Bar or Upper Shelf Support Bracket, loosening the screws in the top panel May help to prevent scratching the Side Panels. 5. Starting at the top of the, snap the upper levels of Fixed Height Shelves 1% down into the Shelf Clips. Rest the Shelf on the Rear Shelf Clips and attach the Front Support Tubes to the Side Panels using with one 1/4-20 x 1.38 Machine Screw u on each side. NOTE: To simplify leveling, do not install the bottom Shelf yet. Final Adjustment 1. Slide the assembled to the intended location. 2. Level the using a 1/4 socket or wrench on the leveler brackets. See Leveling s on page 25. 3. Install the remaining Shelves into the lower levels. Final Bank Assembly 1. Assemble, position and level any remaining cabinets. 2. After all cabinets in the bank have been positioned: a. Attach the Doors. See Attach Doors on page 27. b. Secure the cabinets, see Secure s on pages 39-45. 19

Assembly - Group 5 s 03, 06, 07 Hardware used: 8-32 Insert Nut t #8 x 5/8 Pan Wood Tack Head Screw 1$ #8 x 1-1/4 Pan Dowel Glide 1@ Head Screw 2& i 7 x 50 mm Hex Socket Screw 1! Fixed Height Shelf Clip y Leveler Bracket 1# 5 8 9 13 Left Hinge or Right Hinge 4 Detail 5A Detail 5F 5 25 Right Hinge or Left Hinge 28 26 1 Detail 5B Detail 5G 6 15 6 28 Detail 5C 4 27 Detail 5D 25 26 18 Left Side 13 Detail 5E 12 10 Right Side 2 12 20

Assembly - Group 5 (continued) Preassembly NOTE: For panel orientation: The Left Side Panel q, Right Side Panel w and any Center Panels e have a notch in the bottom front corner. The side panels also have a groove in the rear to receive the Back Panel r. 1. Install Door Mounts. Skip this step if doors will not be installed. a. Per each compartment, lay the Panels flat. For a left side door hinge, lay with the left surface up. For a right side door hinge, lay with the right surface up. b. See Detail 5A. Install door hinge mounts. Use a plastic mallet to pound 8-32 Insert Nuts t into the holes (three per Hinge Mount) located toward the front edge of each Panel. c. See Detail 5B. Install door striker plate mounts. Turn the panels over, use a plastic mallet to pound 8-32 Insert Nuts t into the holes (two per Striker Plate Mount) located toward the front edge of each Panel. 2. Install Shelf Clips. a. See Detail 5C. Per each compartment, turn the panels so their inside surface is up. b. Push Fixed Height Shelf Clips y (two Clips in each panel side/four per shelf) into the inside surface of both compartments (Side or Center Panels). c. Turn any Center Panels over and repeat on the other side. NOTE: Panels can be large and difficult to keep aligned when attaching together with screws. To assist, peg the panels first by inserting Wood Dowels to fit snugly into 5/16 -diameter holes in the Panels. They may need to be tapped into place. 3. Insert Wood Dowels i into: the left and right side edges of the Top Panel o the top edge and notch of any Center Panels e the backside of the Bottom Front Stretcher Panel 1). Panel Assembly 1. Turn the Left and Right Side Panels q and w on edge, with the front edges down. a. With Wood Dowels i, peg the Side Panels to the Top Panel o. b. Attach the Side Panels to the side edges of the Top Panel o with 7 x 50 mm Hex Socket Screws 1!. 2. Peg the Center Panels e to the Top Panel o. a. Peg the Closure Panel 2^ to the Center Panels e. b. Peg the Inside Rear Stretcher Panel 2* to the inside of both Side Panels in front of the groove along the cabinet back (about halfway down). c. Attach the Center Panels e to the Top Panel o with 7 x 50 mm Hex Socket Screws 1!. Do not attach the Closure Panel 2^ or the Inside Rear Stretcher Panel 2* with screws yet. 3. Attach the Back Panel r. a. See Detail 5D. The Bottom Stretcher Panel overlaps the bottom edge of the Back Panel. b. With the three Rear Stretcher Panels facing up, slide the Back Panel into the groove on the Side and Top Panels. 4. Align and clamp the Filler Panel 2% with the Closure Panel 2^ so the pilot holes in the Filler Panel face the Closure Panel. Both Panels should be flush along all edges. NOTE: The Filler Panel 2% is not used on cabinets with a Full- Length Door Installed. 5. See Detail 5G. Attach the Filler Panel 2% to the Closure Panel 2^ using four #8 x 1-1/4 Pan Head Screws from the back side (inside of the cabinet) until the heads of the screws are nearly flush with the back surface and the Filler Panel is tight against the Closure Panel. 6. Attach the Closure Panel 2^, the sides of the Rear Stretcher Panels and Inside Rear Stretcher Panel 2* to both Side Panels, using 7 x 50 mm Hex Socket Screws 1!. 7. With Wood Dowels i, peg the Cross Stretcher Panel 1* to the Bottom Rear Stretcher Panel, then peg the Front Stretcher Panel 1) to it. 8. With Wood Dowels i, peg the Front Stretcher Panel 1) to the notch in the Side Panels. 9. Turn the assembly to face the front edges up. 10. Check that the assembly is square and tighten all screws. Attach Glides and Levelers 1. See Detail 5E. Tack Glides help protect corners and edges while moving the into place. Push or hammer plastic tack glides 1@ into the bottom edge of the Side and any Center panels, about 2 from the corners. 2. Attach Leveler Brackets. a. See Detail 5F. Attach Leveler Brackets 1# to the inside of all four corners of the cabinet using #8 x 5/8 Pan Head Screws 1$. The Leveler Brackets attach to the inside of both Side Panels and to the Front or Rear Stretcher Panels. b. After the Leveler Brackets are attached, screw the levelers in so the plastic glides extend slightly further than the bottom of the levelers. Install Upper Shelves 1. Tip the assembled upright. 2. Recheck that the is square. 3. Recheck and tighten all hex-socket screws. 4. Starting at the top of the, snap the upper levels of Fixed Height Shelves 1% down into the Shelf Clips. NOTE: To simplify leveling, do not install the bottom Shelf yet. Final Adjustment 1. Slide the assembled to the intended location. 2. Level the using a 1/4 socket or wrench on the leveler brackets. See Leveling s on page 25. 3. Install the remaining Shelves into the lower levels. Final Bank Assembly 1. Assemble, position and level any remaining cabinets. 2. After all cabinets in the bank have been positioned: a. Attach the Doors. See Attach Doors on page 27. b. Secure the cabinets, see Secure s on pages 39-45. 21

Assembly - Group 6 17 Hardware used: 8-32 Insert Nut t Wood Dowel i #8 x 5/8 Pan Head Screw 1$ 7 x 50 mm Hex Socket Screw 1! 1/4-20 Insert Nut 2) Tack Glide 1@ 1/4-20 x 5/8 Button Head Screw 2# 3/4 Flat Head Screw 3) Leveler Bracket 1# 0.35 x 0.6 Vinyl Cap 3# Side Leveler 2( Cleat 3@ Left Hinge or 5 Right Hinge 23 31 8 9 4 Top Back Panel pilot holes face outside the. Detail 6A Detail 6F 19 12 Detail 6B 8 13 1 Detail 6C 31 15 5 20 Left Side 33 32 23 13 29 2 20 Detail 6D Right Side 5 4 29 23 31 12 Bottom Back Panel pilot holes face inside the. Detail 6G Detail 6E 22

Assembly - Group 6 17 (continued) Preassembly NOTE: For panel orientation: The Left Side Panel q and Right Side Panel w have a notch in the bottom front corner. 1. Lay the Right Side Panel w flat with the outside surface up. The dowel holes do not go through to the outside surface. 2. Install Door Mounts. Skip this step if doors will not be installed. See Detail 6A. Install door hinge mounts. Use a plastic mallet to pound 8-32 Insert Nuts t into the holes (three per Hinge Mount) located toward the front edge of each Panel. These will later be used for Door Hinges. 3. See Detail 6D. Pound 8-32 Insert Nuts t into the holes (three per Hinge Mount) located toward the front edge of each Panel. These will later be used for Side Levelers. 4. There are thirty holes in the Side Panel that will be used for the Shelf Support Bar. Pound 1/4-20 Insert Nuts 2) into all of these holes. 5. See Detail 6D. Pound 1/4-20 Insert Nuts 2) into the two holes located at the bottom of the Side Panel. These will later be used for Cleats. 6. See Detail 6B. Tack Glides help protect corners and edges while moving the into place. Push or hammer plastic tack glides 1@ into the bottom edge of the Side Panel, about 4 from the corners. 7. See Detail 6E. Attach a Side Leveler 2( towards the front of the Panel using 3/4 Flat Head Screws 3) into the Insert Nuts from Step 3. 8. Repeat steps 1 through 7 on the Left Side Panel q. NOTE: Panels can be large and difficult to keep aligned when attaching together with screws. To assist, peg the panels first by inserting Wood Dowels to fit snugly into 5/16 -diameter holes in the Panels. They may need to be tapped into place. 9. Insert Wood Dowels i into: the left and right side edges of the Top Panel o the top of the Top Front Stretcher Panel 1(. 10. Attach the sides of the Top Front Stretcher Panel 1( to the Top Panel o using 7 x 50 mm Hex Socket Screws 1!. Panel Assembly 1. Turn the Left and Right Side Panels q and w on edge, with the front edges down. a. With Wood Dowels i, peg the Side Panels to the Top Panel o. b. Attach the Side Panels to the side edges of the Top Panel o and the Top Front Stretcher Panel 1( with 7 x 50 mm Hex Socket Screws 1!. 2. With Wood Dowels i, peg the two Back Panels r together and attach them to the Side and Top Panels with 7 x 50 mm Hex Socket Screws 1!. NOTE: The pilot holes at the top of the Top Back Panel face outside of the cabinet and the pilot holes at the bottom of the Bottom Back Panel face inside of the cabinet. 3. For support, temporarily attach one Shelf Support Bar 3! to the bottom of both Side Panels with 1/4-20 x 5/8 Button Head Screws 2# into the Insert Nuts from Step 5. 4. Attach Leveler Brackets. a. See Detail 6C. Attach Leveler Brackets 1# to the inside back corners of the cabinet using #8 x 5/8 Pan Head Screws 1$. The Leveler Brackets attach to the inside of both Side Panels and to the Rear Stretcher Panels. b. After the Leveler Brackets are attached, screw the levelers in so the plastic glides extend slightly further than the bottom of the levelers. Level the 1. Tip the assembled cabinet upright. 2. Check that the assembly is square and tighten all screws. 3. Detach the Shelf Support Bar 3! from the bottom of the Side Panels and set the 1/4-20 x 5/8 Button Head Screws 2# aside. 4. Attach Cleats 3@. NOTE: To keep the cabinet square, maintain the same distance between both Side Panels at the front of the cabinet as it already exists at the rear of the cabinet. a. Attach one Cleat 3@ to each Side Panel using the Screws from Step 3 in the slotted hole of each bracket into the Insert Nuts. Depending on available space, one or two screws may be used. b. Anchor the cleats to the floor using appropriate fasteners (not supplied). 5. Apply one 0.35 x 0.6 Vinyl Cap 3# to each Post of all four Levelers. Install Shelf 1. Attach the Fixed Height Shelf 1% at the required height into the Insert Nuts in the Side Panels using two 1/4-20 x 5/8 Button Head Screws 2# at the end of each Shelf Support Bar 3!. 2. Attach the remaining Shelf Support Bar 3! removed in Step 3 above. a. Align the Bar 3! with the Insert Nuts in the Side panels underneath the middle of the Shelf. b. Attach the both ends of the Bar to the Insert Nuts in the Side Panels using two 1/4-20 x 5/8 Button Head Screws 2#. Final Adjustment 1. Slide the assembled to the intended location. 2. Level the using a 1/4 socket or wrench on the leveler brackets. See Leveling s on page 25. 3. Install the remaining Shelves into the lower levels. Final Bank Assembly 1. Assemble, position and level any remaining cabinets. 2. After all cabinets in the bank have been positioned: a. Attach the Doors. See Attach Doors on page 27. b. Secure the cabinets, see Secure s on pages 39-45. 23

Assembly - Group 6 62 Assembly NOTE: 62 ships fully assembled. Final Adjustment 1. Slide the to the intended location. 2. Check that the assembly is square and tighten all screws. 3. See Detail 6H. Level the using a 1/4 socket or wrench on the leveler brackets. See Leveling s on page 25. 4. Snap the plugs in the round leveler access holes in the bottom shelves. Final Bank Assembly 1. Assemble, position and level any remaining cabinets. 2. After all cabinets in the bank have been positioned: a. Attach the Doors. See Attach Doors - Description on page 27. b. Secure the cabinets, see Secure s on pages 39-45. Detail 6H Leveler Access Hole 24

Level s NOTE: For proper door alignment, follow these instructions carefully. Do not try to level the cabinets to match soffits. Do not try to plumb the cabinet to match adjacent walls. 1. Move the assembled cabinets to be within a few inches of their final location according to the layout drawings and adjust them to be level with each other. 2. a. Check the level of the entire floor where the cabinets will be installed. b. Determine the highest point of the floor in that area. c. The cabinet installed at this highest location will be the reference for all other cabinets to be leveled against. 3. Adjust the levelers on one side until the front edges of the cabinet side panels are plumb (side-to-side). 25

Level s (continued) 4. Measure A and B with a tape and adjust the front levelers until A=B (+1/32 inch). 6. Recheck that A=B. Readjust if necessary (repeat steps 2-4). 5. Adjust both front levelers equally until the front edges of the cabinet are plumb (front-to-back). 7. Adjust the levelers on the adjacent cabinet so it will line up with the top of the highest cabinet. 8. Repeat steps 3-7 for the remaining cabinets. 26

Attach Doors - Description Door Identification Wood and grille door variations are available for the cabinet models. To attach the doors, refer to the appropriate instructions on the following pages. Skip this procedure for cabinets without doors. Individual Compartment Doors (Page ) Single Full-Length Door (Page 32) Double Compartment Doors (Page 34) Double Full-Length Doors (Page 36) 27