DENTAL DIAMOND BURS RHODIUM-PLATINUM DELTADENT snc Via Cavour, 42-20865 Usmate (MB) Tel +39 039 6829298 - Fax +39 039 6076721 www.deltadent.it - info@deltadent.it
BALL SHAPES S1-S1A Spherical burs for preparing small cavities S2-S2A-S3-S3A Spherical burs for cavities and preparing the shoulder and occlusal grooves S4-S5-S6 Spherical burs with diamond-coated neck for shoulder preparation and stump finishig ROUND HEAD TAPERED SHAPES S7-S8-S64 Burs for initial reduction and finishing roundshoulder of crowns, for round-shoulder inlays with or without chamfering, for preparing the finish line of crowns S14-S15-S16 Burs for intial reduction and finishing of crowns and round-shoulder inlays, for the finish line of crowns Ø 021 - stem mm 19 Ø 021 - stem mm 21 S1 S1A S2 S2A S3 S3A S4 S5 S6 S7 S8 S64 S14 S15 S16 001 001 001 001 001 001 002 002 002 199 199 198 198 197 198 FLAT HEAD TAPERED SHAPES / HEXAGONAL SHAPES S9-S10-S11-S12-S13 Burs for initial reduction and finishing of sharp-shoulder crowns and for square-shoulder inlays S17A Medium grain burs for initial reduction of occlusal surfaces and for occlusal corrections TAPERED / CYLINDRICAL SHAPES WITH 50 TAPERED HEAD S21B Tapered burs with tapered head for reducing and preparing the stump with 50 shoulder S18-S19 Cylindrical burs for the abrasion of the tooth and the epithelial lining of the gingival sulcus; facilitates proper redution of gum tissue and tooth structure S20-S21-S21A Cylindrical burs with tapered head for reducing and preparing the stump with 50 shoulder Ø 031 - stem mm 19 Ø 010 - stem mm 18 S9 S10 S11 S12 S13 S17A S21B S18 S19 S20 S21 S21A 170 172 172 173 173 037 289 286 288 289 289 131 INVERTED CONE SHAPES S23-S23A-S24-S24A-S25-S25A-S46 Burs for undercut preparation HOURGLASS / OLIVE SHAPES S26-S27-S28 Burs for finishing undercuts and preparing occlusal grooves in molars and premolars S29-S29A-S29B-S29C Burs for finishing lingual surfaces of incisors and respective gingival margin Ø 021 - stem mm 19 Ø 016 - stem mm 20 Ø 023 - stem mm 20 Ø 023 - stem mm 19 S23 S23A S24 S24A S25 S25A S46 S26 S27 S28 S29 S29A S29C S29B 010 010 010 010 010 010 225 019 019 019 257 257 257 277 FLAT HEAD CYLINDRICAL SHAPES S32-S32A-S33-S34-S34A-S35-S37 Burs for initial reduction and preparation finishing of sharp shoulder crowns and square-shoulder inlays ROUND HEAD CYLINDRICAL SHAPES S36-S36A-S38-S39-S39A-S39B Burs for initial reduction and preparation finishing of roundshoulder crowns and round-shoulder inlay with or without chamfering and for preparing the finish line of crowns Ø 010 - stem mm 21 Ø 008 - stem mm 19 S32 S32A S33 S34 S34A S35 S37 S36 S36A S38 S39 S39A S39B 109 108 110 111 111 111 109 141 141 139 140 141 141
NEEDLE / FISSURE SHAPES S40-S41-S41A-S42-S43-S43A-S43B-S57-S58-S58A Burs for penetrating into the interproximal spaces, for crossing interdental spaces and for the related finishing NON DIAMOND HEAD SHAPES S48-S49 Burs for penetrating into the subgingival spaces without causing damagem or bleeding, identification and widening the entrance of the root canals Ø 010 - stem mm 20 Ø 012 - stem mm 23 Ø 010 - stem mm 25 Ø 014 - stem mm 20 Ø 010 - stem mm 21 Ø 008 - stem mm 24 Ø 007 - stem mm 23 S40 S41 S41A S42 S43 S43A S43B S57 S58 S58A S48 S49 165 166 166 166 164 164 164 196 540 699 190 190 INVERTED CONE SHAPES WITH ROUNDED HEAD S47-S47A-S47B-S45 Burs for preparing cavities with undercut and rounded bottom edge; avoids microfractures of filling materials; for preparing shoulders, for occlusal grooves and lingual grooves in incisors FLAME SHAPES S44-S50-S51-S52-S53-S54-S55-S56 Burs for executing chamfers on the gingival margin, for preparing crowns, for chamfer preparations, for finishing composite restorations and retouching ceramics; for penetrating into the interproximal and subgingival spaces Ø 012 - stem mm 24 S47 S47A S47B S45 S44 S50 S51 S52 S53 S54 S55 S56 237 237 238 273 298 249 249 250 250 250 250 248 SPECIAL BALL SHAPES S59-S60-S61-S62-P1 Spherical burs for preparing small cavities PERIODONTOLOGY SHAPES P1-P2-P3-P4-P5-P6-P7-P8-S63 Medium grain burs for preparing stumps with subgingival chamfer Ø 008 - stem mm 23 Ø 010 - stem mm 24 Ø 012 - stem mm 24 Ø 021 - stem mm 24 S59 S60 S61 S62 P1 P2 P3 P4 P5 P6 P7 P8 S63 001 001 001 001 297 299 297 298 299 298 299 298 299 TORNADO SHAPES / WHEEL SHAPES T1-T2-T3 Burs used for to quickly abrade the axial walls of the stump S30-S31 Burs for finishing lingual surfaces of upper and lower incisors AMALREM SHAPES A1-A2-A3-A4-A5 Coarse grain burs used for amalgam removal or as a crown cutter; excellent for cutting metal and ceramic Ø 037 - stem mm 17 Ø 042 - stem mm 17 Ø 021 - stem mm 19 T1 T2 T3 S30 S31 A1 A2 A3 A4 A5 511 513 519 040 040 001 245 171 109 110
MINIATURE SHAPES FOR CHILDREN AND LIMITED SPACE M1-M2-M3-M4-M5-M6-M7-M8-M9 Burs used where space is limited, with children, small mouths and for treatments on 7th and 8th teeth M1 M2 M3 M4 M5 M6 M7 M8 M9 001 010 172 109 110 165 297 298 237 C1F-C2F-C3F-C4F-C5F-C6F-C7F-C8F Fine grain burs (40 micron), used for composite finishing C9F-C10F-C11F-C12F-C13F-C15F-C16F-C20F Fine grain burs (40 micron), used for compiste finishing C1F C2F C3F C4F C5F C6F C7F C8F C9F C10F C11F C12F C13F C15F C16F C20F 001 257 297 298 287 198 131 141 250 199 172 173 198 289 277 283 C21F-C34F-C34AF-C35F-C36F-C39BF-C41AF-C42F Fine grain burs (40 micron), used for composite finishing C50F-C58F-C58AF-C59F-C60F-C61F-C62F-C29CF Fine grain burs (40 micron), used for composite finishing C21F C34F C34AF C35F C36F C39BF C41AF C42F C50F C58F C58AF C59F C60F C61F C62F 289 111 111 141 141 141 166 166 249 540 699 298 299 298 272 C29CF 257 SHAPES FOR SUPER POLISHING OF COMPOSITES C1S-C2S-C3S-C4S-C5S-C6S Extra fine grain burs (15 micron), used for super polishing of composites Ø 020 - stem mm 20 Ø 014 - stem mm 20 Ø 010 - stem mm 25 Ø 012 - stem mm 24 Ø 008 - stem mm 24 Ø 007 - stem mm 23 Ø 020 - stem mm 20 Ø 016 - stem mm 20 Ø 020 - stem mm 19 Ø 014 - stem mm 17 Ø 014 - stem mm 16 Ø 010 - stem mm 16 Ø 014 - stem mm 16 Ø 010 - stem mm 18 Ø 016 - stem mm 17 Ø 014 - stem mm 16 C1S C2S C3S C4S C5S C6S 001 257 297 298 287 198
SHAPES FOR FINISHING CERAMIC AND ZIRCONIUM CE1-CE2-CE3-CE4-CE5-CE6-CE7-CE7B Burs of double-layer rhodium-platinum alloy, used for finishing ceramic and zirconium SHAPES FOR FINISHING CERAMIC AND ZIRCONIUM CE8-CE9-CE10-CE11-CE12-CE13-CE14-CE15 Burs of double-layer rhodium-platinum alloy, used for finishing ceramic and zirconium Ø 023 - stem mm 19 Ø 042 - stem mm 17 Ø 010 - stem mm 21 CE1 CE2 CE3 CE4 CE5 CE6 CE7 CE7B CE8 CE9 CE10 CE11 CE12 CE13 CE14 CE15 001 001 001 197 010 010 277 257 040 166 249 109 141 111 196 248 SURGICAL SHAPES S65C-S66C-S67C Surgery burs with high-resistance stainless steel shank and diamond-coated surface designed with a special manufacturing process Ø 014 - stem mm 25 Ø 014 - stem mm 30 Ø 018 - stem mm 30 S65C S66C 254 254 199 S67C CHAMFER PREPARATION KIT P3-P6-P7-P8-S29-C3F-C59F-C60F-C61F-C58F Chamfer preparation kit with autoclavable base Ø 023 - stem mm 20 Ø 008 - stem mm 24 P3 P6 P7 P8 S29 C3F C59F C60F C61F C58F 297 298 299 298 257 297 298 299 298 540 SHOULDER PREPARATION KIT S34A-S34-S39B-S39A-S36A-C34AF-C34F-C39BF-C8F- C36F Shoulder preparation kit with autoclavable base S34A S34 S39B S39A S36A C34AF C34F C39BF C8F C36F 111 111 141 141 141 111 111 141 141 141
RHODIUM-PLATINUM DIAMOND BURS TOP DIAMCO working better in not a luxury, but a needsità patent n 1223562 NON-TOXIC The precious Rhodium / Platinum alloy in TOP - DIAMCO burs maintains its metallographic properties unchanged at the high temperatures that can be reached during the work and is virtually indestructible. DOUBLE LIFE The exceptional hardness of the Rhodium / Platinum alloy in TOP - DIAMCO burs, no less than 950 Wickers (against 300 provided by nickel and 600 by chromium), prevents the detachment of diamond crystals; this bur is therefore used until complete consumption of the cutting edges, while maintaining its exceptional features unchanged. LOW HEAT DEVELOPMENT The use of natural diamond in TOP - DIAMCO burs ensures the absence of overheating, unlike the synthetic diamond; moreover, its low coefficient of friction and high abrasive power lower the preparation time, thus allowing you to further reduce the development of heat and the risk of pulpal damage. ABSENCE OF VIBRATIONS The shanks of TOP - DIAMCO burs are made of special high-resistance stainless steel and are electronically calibrated; the diamond-coated surfaces are deposited through an ion bombardment process, which guarantees the perfect uniformity; these features ensure the total absence of vibrations during the work. SELF-CLEANING - HIGH CUTTING SPEED The high molecular compactness of the precious Rhodium / Platinum alloy in TOP - DIAMCO burs, more than three times higher than the conventional binders, in addition to conferring it an exceptional resistance, makes the surface water repellent; during the high-speed rotation, this feature rejects more than 90% of the machining debris. STERILIZABILITY The precious Rhodium / Platinum alloy in TOP - DIAMCO burs can be sterilized an infinite number of times using any system, as the surface layer of the binder is resistant to acids; the burs maintain their colour features unchanged, do not darken and do not tarnish under any circumstances. Diametro della parte lavorante Diameter of the working piece Durchmesser des Arbeitenden Teiles Diamètre de la pièce en fonction Diámetro de la parte que trabaja () 008-010 012-014 016-018 021-023 025-027 029-031 033-040 042-050 Numero di giri consigliato Recommended speed Empfohlene Anzhal der Umdrehungen Nombre de tour conseillés Número acconsejado de revoluciones 100 000-220 000 70 000-220 000 55 000-160 000 40 000-120 000 35 000-110 000 30 000-95 000 25 000-75 000 15 000-60 000 Numero max. di giri R.P.M. Max. speed R.P.M. Max. Anzhal der Umdrehungen R.P.M. Nombre max. de tours R.P.M. Número máx. de revoluciones por minuto R.P.M. 450 000 450 000 450 000 300 000 160 000 140 000 120 000 95 000