EUD320SxxxDV Features Ultra High Efficiency (Up to 94%) Full Power at Wide Output Current Range (Constant Power) Thermal Sensing and Protection for LED Module 010V/PWM/Timer Dimmable (3 Timer Modes) DimtoOff with Standby Power 0.5 W Alwayson Auxiliary Power: 12Vdc, 200mA Output Lumen Compensation Input Surge Protection: 6kV lineline, 10kV lineearth AllAround Protection: OVP, SCP, OTP Waterproof (IP67) SELV Output Suitable for Independent Use 7 Years Warranty Description The EUD320SxxxDV series is a 320W, constantcurrent, programmable LED driver that operates from 90305 Vac input with excellent power factor. Created for many lighting applications including high bay, high mast, aquaculture and sports, it provides a dimtooff mode with low standby power. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure troublefree operation, protection is provided against input surge, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range FullPower Current Range(1) Default Output Current 1051500mA 10501500mA 1400 ma 1542200mA 15402200mA 2100 ma 2243200mA 22403200mA 2800 ma 3224600mA 32204600mA 4200 ma 4696700mA 46906700mA 6700 ma Input Voltage Range(2) Output Voltage Range Max. Output Power Typical Efficiency (3) Power Factor 120Vac 220Vac Model Number 90~305 Vac/ 107~305Vdc 320 W 94.0% 0.99 0.96 EUD320S150DV 127~250 Vdc 90~305 Vac/ 127~250 Vdc 90~305 Vac/ 127~250 Vdc 90~305 Vac/ 127~250 Vdc 90~305 Vac/ 127~250 Vdc 73~208Vdc 320 W 93.5% 0.99 0.96 EUD320S220DV 50~143Vdc 320 W 93.5% 0.99 0.96 EUD320S320DV 35~100Vdc 320 W 93.5% 0.99 0.96 EUD320S460DV(4) 24 ~ 68Vdc 320 W 93.5% 0.99 0.96 EUD320S670DV(4) Notes: (1) Output current range with constant power at 320W (2) Certified Voltage range 100240Vac or 127250Vdc (except CCC, PSE, KC and KCC) (3) Measured at full load and 220Vac input (see below General Specifications for details). (4) SELV Output 1 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV EUD320S150DV IV Operating Area EUD320S220DV EUD320S320DV EUD320S460DV 60%Load 100%Load 78 65 52 EUD320S670DV (469,68) (2814,68) (4690,68) (10%Ioset,320/Ioset) (Ioset,320/Ioset) (6700,47.5) 100%Load 39 26 13 0 (670,24) 60%Load Good Performance Area Allowed Operating Area (Ioset,24) (6700,28.5) (6700,24) 0 1350 2700 4050 5400 6750 8100 Output Current (ma) Note: 4690mA Ioset 6700mA Programmed Operating Area 2 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Input Specifications Input Voltage 90 Vac 305 Vac 127250Vdc Input Frequency 47 Hz 63 Hz Leakage Current 0.70 ma Input AC Current Inrush Current(I 2 t) 1.90 A 2 s PF 0.90 THD 20% THD 10% Output Specifications IEC605981; 240Vac/ 60Hz, grounding effectively 3.30 A Measured at full load and 120 Vac input. 1.80 A Measured at full load and 220 Vac input. At 220Vac input, 25 cold start, duration=3.52 ms, 10%Ipk10%Ipk. See Inrush Current Waveform for the details. At 100240Vac, 5060Hz, 60%100% Load (192320W) At 220240Vac, 5060Hz, 75%100% Load (240320W) Output Current Tolerance 5%Ioset 5%Ioset At full load condition Output Current Setting(Ioset) Range EUD320S150DV EUD320S220DV EUD320S320DV EUD320S460DV EUD320S670DV Output Current Setting Range with Constant Power EUD320S150DV EUD320S220DV EUD320S320DV EUD320S460DV EUD320S670DV Total Output Current Ripple (pkpk) Output Current Ripple at < 200 Hz (pkpk) 105 ma 154 ma 224 ma 322 ma 469 ma 1050 ma 1540 ma 2240 ma 3220 ma 4690 ma 1500 ma 2200 ma 3200 ma 4600 ma 6700 ma 1500 ma 2200 ma 3200 ma 4600 ma 6700 ma 5%Iomax 10%Iomax At full load condition, 20 MHz BW 2%Iomax Startup Overshoot Current 10%Iomax At full load condition No Load Output Voltage EUD320S150DV EUD320S220DV EUD320S320DV EUD320S460DV EUD320S670DV 350 V 240 V 160 V 115 V 78 V At full load condition. Only this component of ripple is associated with visible flicker. Line Regulation ±0.5% Measured at full load Load Regulation ±1.5% 3 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Output Specifications (Continued) Turnon Delay Time Temperature Coefficient of Ioset 1.0 s 0.5 s Measured at 120Vac input, 60%100% Load Measured at 220Vac input, 60%100% Load 0.03%/ C Case temperature = 0 C ~Tc max 12V Auxiliary Output Voltage 10.8 V 12 V 13.2 V 12V Auxiliary Output Source Current 0 ma 200 ma Return terminal is Dim Note: All specifications are typical at 25 C unless otherwise stated. General Specifications Efficiency at 120 Vac input: EUD320S150DV Io=1050mA Io=1500mA EUD320S220DV Io=1540mA Io=2200mA EUD320S320DV Io=2240mA Io=3200mA EUD320S460DV Io=3220mA Io=4600mA EUD320S670DV Io=4690mA Io=6700mA 89.5% 88.0% 89.5% 88.5% 89.5% 87.5% 89.0% 87.5% 89.0% 87.5% 90.0% 90.5% 89.5% 91.0% 89.5% 91.0% 89.5% Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Efficiency at 220 Vac input: EUD320S150DV Io=1050mA Io=1500mA EUD320S220DV Io=1540mA Io=2200mA EUD320S320DV Io=2240mA Io=3200mA EUD320S460DV Io=3220mA Io=4600mA EUD320S670DV Io=4690mA Io=6700mA 90.5% 90.5% 90.0% 90.0% 89.5% 94.0% 92.5% 93.5% 92.5% 93.5% 93.5% 93.5% Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) 4 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV General Specifications (Continued) Efficiency at 277 Vac input: EUD320S150DV Io=1050mA Io=1500mA EUD320S220DV Io=1540mA Io=2200mA EUD320S320DV Io=2240mA Io=3200mA EUD320S460DV Io=3220mA Io=4600mA EUD320S670DV Io=4690mA Io=6700mA 91.0% 90.5% 90.0% 90.5% 90.0% 94.0% 93.0% 94.0% 92.5% 94.0% 93.5% 92.5% 93.5% 5 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Standby power 0.5 W Measured at 230Vac/50Hz; Dimming off MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w 237,000 Hours 97,000 Hours 40 C +89 C 40 C +75 C Measured at 220Vac input, 80%Load and 25 C ambient temperature (MILHDBK 217F) Measured at 220Vac input, 80%Load and 70 C case temperature; See lifetime vs. Tc curve for the details Case temperature for 7 years warranty. Please see Inventronics Warranty Statement for complete details. Storage Temperature 40 C +85 C Humidity: 5%RH to 100%RH Dimensions Inches (L W H) Millimeters (L W H) 8.86 3.86 1.75 225 98 44.8 Net Weight 1875 g Note: All specifications are typical at 25 C unless otherwise stated. Dimming Specifications With mounting ear 9.88 3.86 1.75 251 98 44.8 Absolute Maximum Voltage on the Vdim (+) Pin 20 V 20 V Source Current on Vdim (+)Pin 200 ua 300 ua 450 ua Vdim(+) = 0 V Dimming Output Range EUD320S150DV EUD320S220DV EUD320S320DV EUD320S460DV EUD320S670DV EUD320S150DV EUD320S220DV EUD320S320DV EUD320S460DV EUD320S670DV 10%Ioset Ioset 105mA 154mA 224mA 322mA 469mA Ioset 1050mA Ioset 1500mA 1540mA Ioset 2200mA 2240mA Ioset 3200mA 3220mA Ioset 4600mA 4690mA Ioset 6700mA 105mA Ioset < 1050mA 154mA Ioset < 1540mA 224mA Ioset < 2240mA 322mA Ioset < 3220mA 469mA Ioset < 4690mA
EUD320SxxxDV Dimming Specifications (Continued) Recommended Dimming Input Range 0 V 10 V Dim off Voltage 0.35 V 0.5 V 0.65 V Dim on Voltage 0.55 V 0.7 V 0.85 V Default 010V dimming mode. Hysteresis 0.2 V PWM_in High Level 3 V 10 V PWM_in Low Level 0.3 V 0.6 V PWM_in Frequency Range 200 Hz 3 KHz PWM_in Duty Cycle 1% 99% PWM Dimming off (Positive Logic) PWM Dimming on (Positive Logic) PWM Dimming off ( Negative Logic) PWM Dimming on ( Negative Logic) 3% 5% 8% 5% 7% 10% 92% 95% 97% 90% 93% 95% Hysteresis 2% Dimming mode set to PWM in PC interface. Note: All specifications are typical at 25 C unless stated otherwise. Safety &EMC Compliance Safety Category Standard CE EN 613471, EN61347213 EMI Standards EN 55015 (1) EN 6100032 EN 6100033 EMS Standards EN 6100042 EN 6100043 Notes Conducted emission Test &Radiated emission Test Harmonic current emissions Voltage fluctuations & flicker Notes Electrostatic Discharge (ESD): 8 kv air discharge, 4 kv contact discharge RadioFrequency Electromagnetic Field Susceptibility TestRS EN 6100044 Electrical Fast Transient / BurstEFT EN 6100045 Surge Immunity Test: AC Power Line: line to line 6 kv, line to earth 10 kv (2) EN 6100046 EN 6100048 EN 61000411 EN 61547 Conducted Radio Frequency Disturbances TestCS Power Frequency Magnetic Field Test Voltage Dips Electromagnetic Immunity Requirements Applies To Lighting Equipment 6 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2) To perform electric strength (hipot) testing, the GDT ground disconnect (nut and metal lock sheet) on the driver endcap should be removed temporarily to prevent the internal gas discharge tube from conducting (as allowed by IEC 605981 Clause 10.2). After testing is completed, these items must be reinstalled to restore linetoearth surge protection and secure the end cap. Derating Lifetime vs. Case Temperature 7 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Inrush Current Waveform Efficiency vs. Load EUD320S150DV(Io=1050mA) EUD320S150DV(Io=1500mA) EUD320S220DV(Io=1540mA) EUD320S220DV(Io=2200mA) 8 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV EUD320S320DV(Io=2240mA) EUD320S320DV(Io=3200mA) EUD320S460DV(Io=3220mA) EUD320S460DV(Io=4600mA) EUD320S670DV(Io=4690mA) EUD320S670DV(Io=6700mA) 9 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Power Factor Total Harmonic Distortion Protection Functions External Thermal Protection NTC R1 7.81 kohm R2 4.16 kohm Protection Current Floor When R_NTC falls below R1, External Thermal Protection is triggered, reducing output current until R2 is reached. When R_NTC is less than R2, output current is reduced to the programmed Protection Current Floor. 10%Ioset 60%Ioset 100%Ioset 10%Ioset>Iomin (default setting is 60%) Iomin 60%Ioset 100%Ioset 10%Ioset Iomin (default setting is 60%) Over Temperature Protection Short Circuit Protection Over Voltage Protection Decreases output current, returning to normal after over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. 10 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Dimming 010V Dimming The recommended implementation of the dimming control is provided below. Implementation 1: DC Input Notes: 1. The dimmer can also be replaced by an active 010V voltage source signal or passive components like resistors and zener. 2. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 3. If 010V dimming is not used, Dim + should be open. PWM Dimming Implementation 2: Positive logic Implementation 3: Negative logic 11 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Time Dimming Time dimming control includes 3 kinds of modes, they are Self AdaptingMidnight, Self Adapting Percentage and Traditional Timer. Self AdaptingMidnight: Automatically adjusts the dimming curve based on the ontime of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self AdaptingPercentage: Automatically adjusts the ontime of each step by a constant percentage = (actual ontime for the past 2 days if difference <15 min) / (programmed ontime from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes. Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRGMUL2 (Programmer) datasheet for details. 12 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Mechanical Outline DIMMING WIRE(VDE 5*0.5mm 2 7.2) AC/L (BROWN) AC/N (BLUE) GND (YELLOW/GREEN) INPUT(VDE H05RNF 3*1.0mm 2 7.2) TC OUTPUT(VDE H05RNF 2*1.0mm V+ (BROWN) V (BLUE) PINK BLUE/WHITE BLACK/WHITE PURPLE GRAY 2 6.8) PROJ: Unspecified tolerance:±1 RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products. 13 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com
EUD320SxxxDV Revision History Change Date Rev. Description of Change Item From To 20160328 A Datasheets Release / / KC / Added Models Notes Updated 20170726 B Input Specifications PF/THD Updated Output Specifications Temperature Coefficient of Ioset Updated General Specifications Dimensions Updated Mechanical Outline / Updated Features Alwayson Auxiliary Power Added 20171025 C 20180122 C Features 7 Years Warranty Added General Specifications Operating Case Temperature for Warranty Tc_w Updated Description / Updated General Specifications Lifetime Updated Operating Case Temperature for Warranty Tc_w +70 C +75 C Lifetime vs. Case Temperature / Updated 14 / 14 www.inventronicsco.com Tel: 8657156565800 Fax: 8657186601139 sales@inventronicsco.com