Power MOSFET PRODUCT SUMMRY V DS (V) 600 R DS(on) () V GS = 0 V 0.75 Q g max. (nc) 49 Q gs (nc) 3 Q gd (nc) 20 Configuration Single D D 2 PK (TO-263) G FETURES Low gate charge Q g results in simple drive requirement vailable Improved gate, avalanche and dynamic dv/dt ruggedness vailable Fully characterized capacitance and avalanche voltage and current Material categorization: for definitions of compliance please see www.vishay.com/doc?9992 Note * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non-rohs-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information / tables in this datasheet for details. PPLICTIONS G D S S N-Channel MOSFET Switch mode power supply (SMPS) Uninterruptible power supply High speed power switching PPLICBLE OFF LINE SMPS TOPOLOGIES ctive clamped forward Main switch ORDERING INFORMTION Package D 2 PK (TO-263) D 2 PK (TO-263) D 2 PK (TO-263) Lead (Pb)-free and Halogen-free SiHFS9N60-GE3 SiHFS9N60TRR-GE3 a SiHFS9N60TRL-GE3 a Lead (Pb)-free Note a. See device orientation. Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. ). b. Starting T J = 25 C, L = 6.8 mh, R g = 25, I S = 9.2 (see fig. 2). c. I SD 9.2, di/dt 50 /μs, V DD V DS, T J 50 C. d..6 mm from case. IRFS9N60PbF IRFS9N60TRRPbF a IRFS9N60TRLPbF a SiHFS9N60-E3 SiHFS9N60TR-E3 a SiHFS9N60TL-E3 a BSOLUTE MXIMUM RTINGS (T C = 25 C, unless otherwise noted) PRMETER SYMBOL LIMIT UNIT Drain-Source Voltage V DS 600 V Gate-Source Voltage V GS ± 30 Continuous Drain Current V GS at 0 V T C = 25 C 9.2 I D T C = 00 C 5.8 Pulsed Drain Current a I DM 37 Linear Derating Factor.3 W/ C Single Pulse valanche Energy b E S 290 mj Repetitive valanche Current a I R 9.2 Repetitive valanche Energy a E R 7 mj Maximum Power Dissipation T C = 25 C P D 70 W Peak Diode Recovery dv/dt c dv/dt 5.0 V/ns Operating Junction and Storage Temperature Range T J, T stg -55 to 50 Soldering Recommendations (Peak temperature) d for 0 s 300 C S6-0763-Rev. D, 02-May-6 Document Number: 9287
THERML RESISTNCE RTINGS PRMETER SYMBOL TYP. MX. UNIT Maximum Junction-to-mbient R thj - 40 C/W Maximum Junction-to-Case (Drain) R thjc - 0.75 SPECIFICTIONS (T J = 25 C, unless otherwise noted) PRMETER SYMBOL TEST CONDITIONS MIN. TYP. MX. UNIT Static Drain-Source Breakdown Voltage V DS V GS = 0, I D = 250 μ 600 - - V V DS Temperature Coefficient V DS /T J Reference to 25 C, I D = m - 0.66 - V/ C Gate-Source Threshold Voltage V GS(th) V DS = V GS, I D = 250 μ 2.0-4.0 V Gate-Source Leakage I GSS V GS = ± 30 V - - ± 00 n V DS = 600 V, V GS = 0 V - - 25 Zero Gate Voltage Drain Current I DSS V DS = 480 V, V GS = 0 V, T J = 25 C - - 250 μ Drain-Source On-State Resistance R DS(on) V GS = 0 V I D = 5.5 b - - 0.75 Forward Transconductance g fs V DS = 25 V, I D = 3. 5.5 - - S Dynamic Input Capacitance C iss VGS = 0 V, - 400 - Output Capacitance C oss V DS = 25 V, - 80 - Reverse Transfer Capacitance C f =.0 MHz, see fig. 5 rss - 7. - pf V DS =.0 V, f =.0 MHz - 957 - Output Capacitance C oss V GS = 0 V V DS = 480 V, f =.0 MHz - 49 - Effective Output Capacitance C oss eff. V DS = 0 V to 480 V c - 96 - Total Gate Charge Q g - - 49 Gate-Source Charge Q gs I V GS = 0 V D = 9.2, V DS = 400 V see fig. 6 and 3 b - - 3 nc Gate-Drain Charge Q gd - - 20 Turn-On Delay Time t d(on) - 3 - Rise Time t V DD = 300 V, I D = 9.2 r - 25 - R g = 9., R D = 35.5 Turn-Off Delay Time t d(off) see fig. 0 b - 30 - ns Fall Time t f - 22 - Gate Input Resistance R g f = MHz, open drain 0.5-3.2 Drain-Source Body Diode Characteristics MOSFET symbol Continuous Source-Drain Diode Current I S showing the - - 9.2 D integral reverse G Pulsed Diode Forward Current a I SM p - n junction diode - - 37 Body Diode Voltage V SD T J = 25 C, I S = 9.2, V GS = 0 V b - -.5 V Body Diode Reverse Recovery Time t rr - 530 800 ns Body Diode Reverse Recovery Charge Q rr T J = 25 C, I F = 9.2, di/dt = 00 /μs b - 3.0 4.4 μc Forward Turn-On Time t on Intrinsic turn-on time is negligible (turn-on is dominated by L S and L D ) Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. ). b. Pulse width 300 μs; duty cycle 2 %. c. C oss eff. is a fixed capacitance that gives the same charging time as C oss while V DS is rising from 0 to 80 % V DS. S S6-0763-Rev. D, 02-May-6 2 Document Number: 9287
TYPICL CHRCTERISTICS (25 C, unless otherwise noted) I D, Drain-to-Source Current () 00 0 VGS TOP 5V 0V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.7V 4.7V I D, Drain-to-Source Current () 00 0 T J = 50 C T J = 25 C 20µs PULSE WIDTH 0. T J = 25 C 0. 0 00 V DS, Drain-to-Source Voltage (V) Fig. - Typical Output Characteristics V DS= 50V 20µs PULSE WIDTH 0. 4.0 5.0 6.0 7.0 8.0 9.0 0.0 V GS, Gate-to-Source Voltage (V) Fig. 3 - Typical Transfer Characteristics I D, Drain-to-Source Current () 00 0 VGS TOP 5V 0V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.7V 4.7V 20µs PULSE WIDTH T J = 50 C 0 00 V DS, Drain-to-Source Voltage (V) Fig. 2 - Typical Output Characteristics r DS(on), Drain-to-Source On Resistance (Normalized) 3.0 2.5 2.0.5.0 0.5 I D = 9.2 V GS = 0V 0.0-60 -40-20 0 20 40 60 80 00 20 40 60 T J, Junction Temperature ( C) Fig. 4 - Normalized On-Resistance vs. Temperature S6-0763-Rev. D, 02-May-6 3 Document Number: 9287
C, Capacitance (pf) 2400 2000 600 200 800 400 iss oss rss V GS = 0V, f = MHz C iss = C gs C gd, C ds SHORTED C rss = Cgd C oss = C ds Cgd I SD, Reverse Drain Current () 00 0 T J = 50 C T J = 25 C 0 0 00 000 V DS, Drain-to-Source Voltage (V) Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage V GS = 0 V 0. 0.2 0.5 0.7.0.2 V SD,Source-to-Drain Voltage (V) Fig. 7 - Typical Source-Drain Diode Forward Voltage V GS, Gate-to-Source Voltage (V) 20 6 2 8 4 I = D 9.2 V DS = 480V V DS = 300V V DS = 20V FOR TEST CIRCUIT SEE FIGURE 3 0 0 0 20 30 40 50 Q G, Total Gate Charge (nc) Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage I D, Drain Current () 000 00 0 OPERTION IN THIS RE LIMITED BY R DS(on) 0us 00us ms 0ms TC = 25 C TJ = 50 C Single Pulse 0. 0 00 000 0000 V DS, Drain-to-Source Voltage (V) Fig. - Maximum Safe Operating rea S6-0763-Rev. D, 02-May-6 4 Document Number: 9287
0.0 V DS R D I D, Drain Current () 8.0 6.0 4.0 2.0 R g V GS 0 V Pulse width µs Duty factor 0. % D.U.T. - V DD Fig. 0a - Switching Time Test Circuit V DS 90 % 0.0 25 50 75 00 25 50 T C, Case Temperature ( C) Fig. 8 - Maximum Drain Current vs. Case Temperature 0 % V GS t d(on) t r t d(off) t f Fig. 0b - Switching Time Waveforms Thermal Response (Z thjc ) 0. D = 0.50 0.20 0.0 0.05 t 0.02 SINGLE PULSE t2 0.0 (THERML RESPONSE) Notes:. Duty factor D = t / t 2 0.0 2. Peak T J = P DM x Z thjc TC 0.0000 0.000 0.00 0.0 0. t, Rectangular Pulse Duration (sec) PDM Fig. - Maximum Effective Transient Thermal Impedance, Junction-to-Case 5 V V DS t p V DS L Driver R g 20 V t p D.U.T I S 0.0 Ω - V DD I S Fig. 2a - Unclamped Inductive Test Circuit Fig. 2b - Unclamped Inductive Waveforms S6-0763-Rev. D, 02-May-6 5 Document Number: 9287
E S, Single Pulse valanche Energy (mj) 600 500 400 300 200 00 TOP BOTTOM I D 4. 5.8 9.2 0 25 50 75 00 25 50 Starting T, Junction Temperature ( J C) Fig. 2c - Maximum valanche Energy vs. Drain Current Current regulator Same type as D.U.T. 0 V Q G 2 V 0.2 µf 50 kω 0.3 µf Q GS Q GD D.U.T. V - DS V G V GS Charge Fig. 3a - Basic Gate Charge Waveform 3 m Fig. 3b - Gate Charge Test Circuit I G I D Current sampling resistors S6-0763-Rev. D, 02-May-6 6 Document Number: 9287
Peak Diode Recovery dv/dt Test Circuit D.U.T. - Circuit layout considerations Low stray inductance Ground plane Low leakage inductance current transformer - - R g dv/dt controlled by R g Driver same type as D.U.T. I SD controlled by duty factor D D.U.T. - device under test - V DD Driver gate drive P.W. Period D = P.W. Period V GS = 0 V a D.U.T. I SD waveform Reverse recovery current Body diode forward current di/dt D.U.T. V DS waveform Diode recovery dv/dt V DD Re-applied voltage Inductor current Body diode forward drop Ripple 5 % I SD Note a. V GS = 5 V for logic level devices Fig. 4 - For N-Channel maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?9287. S6-0763-Rev. D, 02-May-6 7 Document Number: 9287
Package Information TO-263B (HIGH VOLTGE) (Datum ) 3 4 E 4 L 4 D H 2 C 3 C L2 B B 5 Detail c2 B Gauge plane 0 to 8 L3 L L4 Detail Rotated 90 CW scale 8: H B Seating plane 2 x b2 2 x e 2 x b 0.00 M M B Plating 5 b, b3 c ± 0.004 M B Base metal E D 4 (c) c 5 Lead tip (b, b2) Section B - B and C - C Scale: none E View - 4 MILLIMETERS INCHES MILLIMETERS INCHES DIM. MIN. MX. MIN. MX. DIM. MIN. MX. MIN. MX. 4.06 4.83 0.60 0.90 D 6.86-0.270-0.00 0.25 0.000 0.00 E 9.65 0.67 0.380 0.420 b 0.5 0.99 0.020 0.039 E 6.22-0.245 - b 0.5 0.89 0.020 0.035 e 2.54 BSC 0.00 BSC b2.4.78 0.045 0.070 H 4.6 5.88 0.575 0.625 b3.4.73 0.045 0.068 L.78 2.79 0.070 0.0 c 0.38 0.74 0.05 0.029 L -.65-0.066 c 0.38 0.58 0.05 0.023 L2 -.78-0.070 c2.4.65 0.045 0.065 L3 0.25 BSC 0.00 BSC D 8.38 9.65 0.330 0.380 L4 4.78 5.28 0.88 0.208 ECN: S-820-Rev., 5-Sep-08 DWG: 5970 Notes. Dimensioning and tolerancing per SME Y4.5M-994. 2. Dimensions are shown in millimeters (inches). 3. Dimension D and E do not include mold flash. Mold flash shall not exceed 0.27 mm (0.005") per side. These dimensions are measured at the outmost extremes of the plastic body at datum. 4. Thermal PD contour optional within dimension E, L, D and E. 5. Dimension b and c apply to base metal only. 6. Datum and B to be determined at datum plane H. 7. Outline conforms to JEDEC outline to TO-263B. Document Number: 9364 www.vishay.com Revision: 5-Sep-08
N826 RECOMMENDED MINIMUM PDS FOR D 2 PK: 3-Lead 0.420 (0.668) 0.635 (6.29) 0.355 (9.07) 0.45 (3.683) 0.35 (3.429) 0.200 (5.080) 0.050 (.257) Recommended Minimum Pads Dimensions in Inches/(mm) Return to Index Document Number: 73397 -pr-05 www.vishay.com
Legal Disclaimer Notice Vishay Disclaimer LL PRODUCT, PRODUCT SPECIFICTIONS ND DT RE SUBJECT TO CHNGE WITHOUT NOTICE TO IMPROVE RELIBILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. ll operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 20/65/EU of The European Parliament and of the Council of June 8, 20 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 20/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709 standards. Please note that some Vishay documentation may still make reference to the IEC 6249-2-2 definition. We confirm that all the products identified as being compliant to IEC 6249-2-2 conform to JEDEC JS709 standards. Revision: 02-Oct-2 Document Number: 9000